Cannot establish multiple simultaneous PPTP connections with the CISCO 1841.

Hello everyone;
I have recently tested a PPTP connection with a CISCO 1841 router and got success. I have configured a windows 7 client and successfully connected to the router and was able to access the documents in the server PC that I have mentioned in the attached diagram. I have created number of different users in the CISCO 1841 too. While some one is having a connection, another user cannot connect to it, which means multiple simultaneous connections aren't possible. Do I have to create a ACL for the PPTP and if yes, How ?
FastEthernet0/0 is up, line protocol is up
Internet address is 192.168.100.1/25
Broadcast address is 255.255.255.255
Address determined by non-volatile memory
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is not set
Inbound access list is 100
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is enabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is enabled
IP fast switching on the same interface is disabled
IP Flow switching is disabled
IP CEF switching is enabled
IP CEF Feature Fast switching turbo vector
IP multicast fast switching is enabled
IP multicast distributed fast switching is disabled
IP route-cache flags are Fast, CEF
Router Discovery is disabled
IP output packet accounting is disabled
IP access violation accounting is disabled
TCP/IP header compression is disabled
RTP/IP header compression is disabled
Policy routing is disabled
Network address translation is enabled, interface in domain inside
BGP Policy Mapping is disabled
WCCP Redirect outbound is disabled
WCCP Redirect inbound is disabled
WCCP Redirect exclude is disabled
Inbound inspection rule is SDM_LOW
--------------------------------------------------------------------------------------------ACL 100-----------------------------
deny icmp any any echo-reply
deny ip host 255.255.255.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip host 66.163.169.186 any
permit ip any any (122467027 matches)

As long as you have the inspection engine enabled on the ASA, it shouldn't freak out of the different IP as it will inspect the call signalling and will NAT it accordingly, BUT, for simplicity, I agree with you, it would cause a lot of troubleshooting headache if there is problem as well as reconfiguration of IP on the host ends.
Here is the NAT FYI:
object network obj-10.10.96.0
   subnet 10.10.96.0 255.255.255.0
object network obj-192.168.96.0
   subnet 192.168.96.0 255.255.255.0
object network obj-10.10.14.0
   subnet 10.10.14.0 255.255.255.0
object network obj-10.1.0.0
   subnet 10.1.0.0 255.255.255.0
object network obj-192.168.1.0
   subnet 192.168.1.0 255.255.255.0
object network obj-10.10.11.0
   subnet 10.10.11.0 255.255.255.0
object network obj-192.168.11.0
   subnet 192.168.11.0 255.255.255.0
nat (inside,outside) source static obj-10.10.96.0 obj-192.168.96.0 destination static obj-10.10.14.0 obj-10.10.14.0
nat (inside,outside) source static obj-10.1.0.0 obj-192.168.1.0 destination static obj-10.10.14.0 obj-10.10.14.0
nat (inside,outside) source static obj-10.10.11.0 obj-192.168.11.0 destination static obj-10.10.14.0 obj-10.10.14.0

Similar Messages

An error when trying to connect with the Cisco AnyConnect.

Good day!
I connect from Windows 7 (also from Ubuntu) with the Cisco AnyConnect client 3.0 (and with Cisco AnyConnect Secure Mobility Client 3.1) and get error a “The VPN client was unable to successfully verify the IP forwarding table modifications. A VPN connection will not be established. No changes had been made to the configuration of my asa5520 running 8.4(2) (ASDM 6.4(5)).
I have license (AnyConnect Premium Perpetual) supports 2 vpn connections.
I read about this problem on different forums and cisco.com:
disabled unused adapters, check install software (Adobe photoshop and Bonjour are not installed on my system).
I made new configuration AnyConnect in ASDM. But the problem remains the same...
Please, help me find the way to solution in this situation!

I have seen that error before but it usually clears up on its own. I have a working theory though so perhaps this might help you. I noticed that once you connect, 2 files are created in C:\ProgramData\Cisco\Cisco AnyConnect VPN Client. I think that folder is different if using v3.x instead of 2.5. Anyway, the files are routechangesv4.bin and routechangesv6.bin. Try deleting each and then rebooting. Try connecting again after that.
My theory is that those files are not clearing up after disconnecting. I think they are supposed to go away after disconnecting but I noticed in some cases that they don't.

CAD Problem: Lost connection with the cisco unified ccx application server

I have two locations in our help desk area that consistantly loose connection. I checked the network and we ran new cables. Still having the same issue. They have connectivity to everything else when they loose connection to CAD so I believe there is something going on with the program itself. I have attached the logs from both. There is nothing else that lives on their subnet.
There are 2 servers, the primary 172.29.0.22 and the secondary 172.29.0.23. The Primary is the active server so it is in the same building as the agents.
Can anyone please advise? any help would truly be appreciated!

Hello DJ,
Thank you for replying. No nothing else lives on their subnet.
There are 2 servers, the primary 172.29.0.22 and the secondary 172.29.0.23. The Primary is the active server so it is in the same building as the agents.
I am completely stumped. I have no Idea why this is occuring.

JDBC receiver error Cannot establish connection with the registered driver

Hi Expert,
I am constructing a proxy to JDBC scenario. And I am getting error saying "
Message processing failed. Cause: com.sap.engine.interfaces.messaging.api.exception.MessagingException: Error when attempting to get processing resources: com.sap.aii.af.lib.util.concurrent.ResourcePoolException: Unable to create new pooled resource: DriverManagerException: Cannot establish connection with the registered driver. oracle.jdbc.driver.OracleDriver returns: The Network Adapter could not establish the connection. : SQLException: The Network Adapter could not establish the connection"
I can get into my Oracle database using TOAD with same IP address, user name and password. Could anybody tell me what should I do? Thanks a lot!
Charles

Hi,
Check with your network team, network conenction between PI and Data base not working , Network team have to open Data base system ports inorder connect PI System.
check with Basis team about network connectivty,like they are bale to ping Data base server ip or not.
please go through below thread,
SQLException: Io exception: The Network Adapter could not establish the con
regards,
ganesh.

How to establish connection with the outgoing email server?

Cannot set up Lightroom 5 email capability with Google Mail. Have confirmed proper smpt address, email and password and error message still comes up:
"eFailed to establish connection with the outgoing email server. Please make sure you have entered the email account and password correctly."
How can I clear this up. Help, Adobe!

Have you checked your Gmail in-box? See if this helps:
https://forums.adobe.com/thread/1642613

Can't establish a sftp connection with the finder

Hi, I'm trying to establish a sftp connection with the finder (using the "Connect to server" feature) between my (recently purchased) Mac Mini (mid 2011: i5, 2.3 GHz, 2 GB, running 10.7.3) and a Debian Testing box and I can't, I get the following error:
'There was a problem connecting to the server "ip.address"
This file server will not allow any additional users to log on. Try to connect again later.'
However if I try establishing a connection from the terminal (either ssh or sftp) it works flawlessly:
SSH:
victoria:~ RonIn$ ssh [email protected]
[email protected]'s password:
Linux clementine 3.0.0-1-486 #1 Sat Aug 27 15:56:48 UTC 2011 i686
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
You have new mail.
Last login: Sat Apr 28 21:52:18 2012 from ukamy.local
ronin@clementine:~$
SFTP:
victoria:~ RonIn$ sftp [email protected]
[email protected]'s password:
Connected to ip.address.
sftp>
I've searched for a fix or alternative on the internet and I haven't found one that works; The one that keeps coming up is to try: "ftps" as the protocol instead of "sftp" with the remaining information the same (it doesn't work, it gets the same error message afterwards).
The IP address and login information works (corroborated by the fact that I can log in from the terminal from the Mac Mini) so the only issue is with the finder capabilities for establishing the connection. I have looked for apple related documentation or How Tos but I haven't found anything useful.
I don't want to use any third party app or tweak because of the sensitive information that is going to be transfered, I would like to be using strictly the tools from the OS.
If you need any more information please let me know, any help is deeply appreciated.

I have the same issue although i kind of fixed it. I have two admin accounts and one of the account's safari did the same thing as yours, except, it was the startpage and everypage i tried to visit. I reseted safari, as in the erase all data safari in the toolbar, safari-Reset Safari... But safari still didn't work. I logged out and went to my other account and opened safari. Now it works fine on both accounts. This meant safari had to logout before actually working better. I have this a few times these days.

I installed adobe digital editions but when I want to authorize a device (an e-reader) it doesn't work, I receive an error message that digital editions cannot connect with the activation server. what can I do?

I installed adobe digital editions but when I want to authorize a device (an e-reader) it doesn't work, I receive an error message that digital editions cannot connect with the activation server. what can I do?

Please quote the exact error message, word-for-word, verbatim.
What is your operating system?
What version of Lightroom?

Run report cause "The page cannot be displayed" OR The connection with the

Hello,
1. Database oracle 10g R2 on windows 2003 server enterprise edition with SP2
2. Application Server Oracle 10g R2 on Windows 2003 Server with SP2.
Problem explanation
one of our branch which is connected via leased line is unable to run some of the reports if the report have a little more
data,
one report i tried its size is almost 900k ( they are using the same line since last three month and they are
able to run all reports before, bandwidth is 128k), if you run report browser search a little while
for output then displayed "The page cannot be displayed" if you look at the report log it's finished successfully.
I try to download the report rather opening in browser it reach to end of in downloading window at the end it display
this message
Internet explorer can not download getjobidxxx.xls from oracleaps.domain.com
The connection with the server was reset.
I want to mention one more thing there is a ISA server and firewall in between client and Server but its the same condition
for
head office client but they are able to run all report with out any error.
any one have idea??
Thanks and Regards,
Khawar

Hello,
Thanks for reply, I have posted Service Request to Oracle Metalink and finally resolve the issue, they suggested me the following solution( a note has also been posted in Knowledge Base no. 871016.1 )
Webcache KeepAlive timeout is reached. (The default value for KeepAlive timeout is 5 seconds)
Increase the Keepalive time in webcache to a higher value
**************EOF******************
Thanks and Regards,
Khawar

"Disk Utility has lost its connection with the Disk Management Tool and cannot continue. Please quit and relaunch Disk Utility." Trying to format my iomega external HD for use with Mac

Hi. Trying to connect iomega ext. HD. i have to reformat for Mac. When i plug in & go to Disk Utility,the external shows up and i'm supposed to click "partition". When i do, a box comes up saying ""Disk Utility has lost its connection with the Disk Management Tool and cannot continue. Please quit and relaunch Disk Utility." I quit and relaunched, same results. After googling my question, i came up with this:
"Disk Utility has lost its connection with the Disk Management Tool and cannot continue. Please quit and relaunch Disk Utility."
(Quitting and reopening Disk Utility does not help.)
The following also appears in Console log:
*** malloc[419]: Deallocation of a pointer not malloced: 0x290a410; This could be a double free(), or free() called with the middle of an allocated block; Try setting environment variable MallocHelp to see tools to help debug : for architecture i386 object: ./Applications/iTunes.app/Contents/MacOS/iTunes malformed object (unknown flavor for flavor number 0 in LC_UNIXTHREAD command 27 can't byte swap it)
Workaround
Quit Disk Utility.
From the Finder's Go menu, choose Go to Folder....
Type the following, then click OK: /Library/Receipts
Temporarily remove these iTunes receipts from /Library/Receipts (sort the folder alphabetically as a list):
iTunes.pkg
iTunes4.pkg
You can put them on the desktop, for example. Do not remove iTunesX.pkg or iTunes Phone Driver.pkg.
Open Disk Utility and repair disk permissions again.
Quit Disk Utility.
Put the removed iTunes receipts back in /Library/Receipts.
Note: This issue does not affect Disk Utility's verify or repair disk features.
All seemed good, for a moment, until, upon going back to Disk Utility after removing itunes4.pkg and putting on desktop (i did not have itunes.pkg to remove) the same thing was happening. When i highlite my iomega ext. on left of page, disk perrmissions is grayed and does not allow me to click on it. Same problem from the start. Can somebody please help me out here? That would soooo awesome. Thanx!

i'm just scared i will do something wrong on my own and lose my data.
You shouldn't be scared of that, because you should already have backups. If you don't have backups, then backing up is the first priority.
Insert the Snow Leopard DVD and restart. When you hear the chime, hold down the C key and keep holding it until the Apple logo appears on the display. You should now see the language selection screen. Select your language, then choose Utilities > Disk Utility from the menu bar. In the Disk Utility window, select the external drive (not the internal). The drive may already have a data partition, in which case there will be another icon below the drive icon. Choose the drive icon, then select the Partition tab. Create a single partition with the default options (GUID partition table, Mac OS X Extended Journaled).
When the partitioning is done, select the startup volume on your internal drive in the DU window. Select the Restore tab. Drag the icon of the startup volume to the "Source" field. Then drag the icon of the newly-created volume on the external drive to the "Destination" field. Make sure you have this right. Then click the Restore button, and the data on your startup volume will be copied to the external drive.

I used to be able to email photos from my Lightroom software quite successfully. I needed to change my password several days ago in my gmail account. Now when I try to email photos I receive a message saying "Failed to establish connection with the outgoi

I used to be able to email photos from my Lightroom software 5.7 for MAC quite successfully. I needed to change my password several days ago in my gmail account. Now when I try to email photos I receive a message saying "Failed to establish connection with the outgoing email server. Please make sure you have entered the email account and password correctly."
I have been trying to get help from Adobe for 3 days. I have sent a message through "Get Support", 2 days ago, but no one has contacted me. I have tried by phone, but no one will help me. When I purchased Lightroom in May, 2014, I was able to receive phone help. I am now told that I don't qualify because I am not a Creative Cloud customer. I have been assigned a case number 186291729.
PLEASE HELP ME FIX THIS PROBLEM

I, too, have this problem. I see no one is responding with a solution? Hello? Can someone please advise?
Oh, and, yes, I have manually verified repeatedly that the information I gave to Lightroom is correct, and I still get the same error message when I try to validate.

Why does itune keep telling me it could not establish a connection with the software update server

i have an iphone 3g running on 3.1.3 firmware and every time i plug into my pc running windows 7 it says that it is contacting the software update sever then after about ten seconds it says that update failed could not establish a connection with the server i have tried to disable my firewalls completely and it seems that nothing works nothing is wrong with the iphone it sync's properly and works fine someone plz help me so i can update

Everybody is tryng to connect to apple,s servers. Try tomorrow, it will be quieter

After upgrading to OX mountain lion my apps store doesn't open. App Store cannot verify a secure connection with the App Store. My internet connection is ok but i don't why this happening. What should i do?

After upgrading to OX mountain lion my apps store doesn't open. App Store cannot verify a secure connection with the App Store. My internet connection is ok but i don't why this happening. What should i do?

Hi Tahan007,
Check these threads out:
Cannot connect to the App Store since upgrading to Mountain Lion.
Cannot connect to App Store since 10.8.1
why is my app store sign in saying connection failed?
Also if you're running any anti-virus SW, you might try temporarily disabling it

How do I fix the App Store cannot verify a secure connection with the App Store. in mountain lion tried safari reset, changing the MTU nothing works

Hi all,
how do I fix the App Store cannot verify a secure connection with the App Store. in mountain lion tried safari reset, changing the MTU nothing works at this time. I am using a IMac ML 10.8.2
Would like some help please.
Gee

Hi all,
how do I fix the App Store cannot verify a secure connection with the App Store. in mountain lion tried safari reset, changing the MTU nothing works at this time. I am using a IMac ML 10.8.2
Would like some help please.
Gee

I recently moved into a new apartment and I can connect with the internet by direct connection to the cable/internet modem. But when I connect my Airport Express, it just blinks with a yellow light and I cannot connect via WiFi. Any suggestions?

I recently moved into a new apartment and can connect with the internet by direct attachment to the cable/internet modem. But when I try to connect the modem to my Airport Express, the Airport just blinks yellow and I cannot get my WiFi. Any suggestions?

Try this User Tip from forum expert Tesserax:
AirPort - Complete Power Recycle

TS1702 After I resynced the iPad I cannot connect with the downloaded apps.

After I re-synced the iPad, I cannot connect with the downloaded apps.

Try download any free app to unfreeze the frozen app.

Cannot establish multiple simultaneous PPTP connections with the CISCO 1841.

Similar Messages

Maybe you are looking for