Canon MP450 - Driver not showing up in Print Settings

Has anyone had success using the Canon MP450
I have tried every driver but cant get it to show in the Printer Selection preferences

hey man. i had the same problem and actually just downloaded some driver software at this cannon website. all you have to do is enter your processor information and download it. hope it works out for you!
http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=DownloadDet ailTabAct&fcategoryid=334&modelid=11865
.mike

Similar Messages

  • Driver not showing up in printer menu

    My Epson StylusPro3800 just stopped communicating with all of the Macs on my network. I receive a cryptic "communications error" message when I try to print to it.
    I rebooted the Mac and tried again. Same result. I tried another Mac on the network, same result. I swapped ethernet cables and the port in my switch the cable to the printer is plugged into, to see if it was a cable or port problem. Same result. (All the other devices going through the switch are communicating with no problem.)
    I deleted the printer from the Printer & Fax preferences file. However, after I reinstalled the driver software, when I went to the Add new printer dialog box, the Epson printer does not show up under the AppleTalk menu as it used to. The other printer on my network does show up.
    What do I do now?

    Keith Thirgood wrote:
    I' ve tried restarting the printer with the same results.
    In your original posted, you stated "another Mac." If you did not delete and re-install the print driver on that Mac, can it see the Epson printer?
    As for your computer (the one in which you re-installed the print driver), you might consider checking the hard disk just in case a file might be corrupt. To do that, boot your computer with the OS Install disk holding down the "c" key. Choose your language.
    Go to the Utilities menu and select Disk Utilities.
    In the left pane, click on your hard disk. On the right pane, click the First Aid tab and below, click the button Repair Disk. (If it finds any errors it will attempt to fix and rerun the test.)
    Afterwards, click the Repair Disk Permissions.
    Reboot your computer.
    When I try Default, two Adobe PDF printers show up as well as the AppleTalk Ricoh and a Bonjour Ricoh. No Epson printer shows up.
    Consider checking the network settings on the printer itself. See FAQ at
    http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&info Type=FAQ&oid=79928&prodoid=63062509&foid=88080
    You might also consider setting the printer up as with an IP address. (See the Network or User Guides that you received with the printer or the Epson website.)
    FYI: I used to have an Epson 3000 and now have an Epson 3880 and find IP with LPD protocol faster than AppleTalk.
    HTH

  • HT2250 I have an Apple network utility that with the previous printer (Canon PIXMA iP 5000) found the printer on the Network for use on a wi fi system but a newish printer (Canon MG6150) does not show up as Bonjour.  Is that correct?

    I have an Apple network utility that with the previous printer (Canon PIXMA iP 5000) found the printer on the Network for use on a wi fi system but a newish printer (Canon MG6150) does not show up as Bonjour.  Is that correct?
    paul.kelly

    Hi Steve,
    No expert, but since nobody else has piped in...
    Did you setup the DNS Server IP?

  • A printer that I have connected to my iMac via usb in not showing up in printer options on my iPhone or iPad and it use to before I upgraded to 8.1

    A printer that I have connected to my iMac via usb in not showing up in printer options on my iPhone or iPad and it use to before I upgraded to 8.1. How can I fix this?

    Is it an Airprint-compatible printer, and is its WiFi enabled if it is? (see: About AirPrint)
    If it isn't an Airprint supported printer, then you need a 3rd party driver on your iMac to print from an iPhone. Such as Printopia. As it worked in the past you probably have such a printer driver installed; check and see if it's running.
    Beyond that try restarting the printer, restarting the phone, restarting your router, and restarting your computer.

  • My external hard drive not showing up

    Hello,
    My external hard drive is not showing up on my desktop. I went to finder & preferences>general and made sure I checked "show these items" and checked hard drives. I even unchecked it because I have 2 other external hard drives. When I checked the hard drive box the other 2 hard drives appeared but the third hard drive did not. The hard drive not showing up on my desk top does show up when I double click my system hard drive & can be opened from there, but I want to see it on my desk top. Any help would be appreciated.
    Thanks

    This procedure is a diagnostic test. It makes no changes to your data.
    Please triple-click anywhere in the line below on this page to select it:
    ls -@Oaen /V* | pbcopy
    Copy the selected text to the Clipboard by pressing the key combination command-C.
    Launch the built-in Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    Paste into the Terminal window by pressing the key combination command-V. I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting.
    Wait for a new line ending in a dollar sign ($) to appear below what you entered.
    The output of the command will be automatically copied to the Clipboard. If the command produced no output, the Clipboard will be empty. Paste into a reply to this message.
    The Terminal window doesn't show the output. Please don't copy anything from there.
    If any personal information appears in the output, anonymize before posting, but don’t remove the context.

  • Drive Not Showing In Startup Disk

    I have re setup my MacBook Pro, all seems well apart from this little problem. My Mac OS X Partition or Windows Partition shows in startup Disk.
    Both Operating Systems do startup fine though.
    I have my disk partitioned like this
    Free Space
    Windows 7
    Mac OS X
    Its setup in this way so i can use TrueCypt for the Windows side.
    Does anyone know how to correct this please?
    You can use this link to view a screenshot
    http://www.edugeek.net/attachments/forums/mac/9912d1302462528-drive-not-showing- startup-disk-screen-shot-2011-04-10-20.07.19.png
    Thanks

    if you try to verify the disk, dose it report any errors? (open disk utility, click on the Macintosh HD, click on the repair tab, click verify disk.)
    If you option boot, dose the computer list both Boot Volumes?
    Have you tried blessing the mac hard drive?
    ie: "sudo bless -folder /Volumes/Macintosh\ HD/System/Library/CoreServices -bootinfo"
    (note the above bless command blesses the Hard Drive with the name "Macintosh HD", if you mac volume has a different name, change to match your hard drive's name.)

  • Add PDF to iTunes not showing up in print PDF pop up menu

    Add PDF to iTunes not showing up in print PDF pop up menu. I lost the print PDF to iTunes option. its no longer there. I still have web reciets and mail. also when i add in "edit menu" they don't get added.all this used to work fine

    i found the answear. go to library/PDF Services  or  ~/Library/PDF/Services and clean out this folder. you can also add scripts and automator scripts to add things

  • Bootcamp drive not showing up in Lion

    hi! ^^
    Bootcamp drive not showing up in Lion.
    Lion is just downgrade version of Leopard.
    nothing changed but good functions are disappear.
    c:/aaa folder? i can not access directly from os x boot.
    haha.

    Click Start, then click All Programs.
    Click Accessories, and then click Run.
    Type regedit, and then click OK.
    If you are prompted for an administrator password or for a confirmation, type the password, or click Allow.
    MAKE BACKUP OF REGISTRY
    In the navigation pane, locate and then click the following registry subkey:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E965-E325-11CE-BFC1-08002BE10318}
    In the right pane, click UpperFilters.
    Note You may also see an UpperFilters.bak registry entry. You do not have to remove that entry. Click UpperFilters only. If you do not see the UpperFilters registry entry, you still might have to remove the LowerFilters registry entry. To do this, go to step 8.
    On the Edit menu, click Delete.
    When you are prompted to confirm the deletion, click Yes.
    In the right pane, click LowerFilters.
    Note If you do not see the LowerFilters registry entry, unfortunately this content cannot help you any further. Go to the "Next Steps" section for information about how you can find more solutions or more help on the Microsoft Web site.
    On the Edit menu, click Delete.
    When you are prompted to confirm the deletion, click Yes.
    Exit Registry Editor.
    Restart the computer.

  • USB External drive not showing in Finder, or on Desktop

    I have two USB external drives from the same manufacturer. One is for regular storage, the second is for Time Machine and movies.
    The first one shows everywhere, on the desktop, in finder and in Disk Utility.
    The second drive shows in Disk Utility only. However, it is functioning fine with Time Machine. So it is mounted. I have tried several repairs, and it reports no fault found. So it is certainly functioning correctly, but a setting or error in the operating system is not allowing it to be viewed in finder, or on the desktop.
    Any suggestions.

    Correction: Title should be Firewire External drive not showing in Finder, or on Desktop.

  • Why is my External Hard Drive not showing in Aperture 3.6 Import?

    Why is my External Hard Drive not showing in Aperture 3.6 Import?
    Only my computer hard drive is and I want to import from an external drive.  I have always been able to until I updated to Aperture 3.6 and Yosemite.

    Only my computer hard drive is and I want to import from an external drive.  I have always been able to until I updated to Aperture 3.6 and Yosemite.
    I had the same problem. On the folders on the drive with the Aperture library did show in the Import panel. After I clicked the computer icon in the upper left corner of the Import panel, suddenly all drives appeared.
    You can also try to drag the folder you want to import into the Import panel, to point the file chooser to the drive.

  • HP-photosmart 6280 all-in-one with osx 10.9 now does not show options for printing photos from the photo tray.

    Using osx mavericks on macbook pro.  My printer for HP-photosmart 6280 all-in-one now does not show options for printing photos from the photo tray.

    What router? Have you restarted the router?
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Excel 2010 not using the default print settings

    Currently got an issue with Excel 2010 not using the default print settings for a couple of users on our network,
    basically when pressing cntrl P or selecting the print option from the file menu the printer settings are different to the print settings selected in the devices and printers menu, we have checked the print drivers etc but this has still not resolved the
    issue, all other office programs are fine and also other users are reporting this issue more and more with different printers,
    tried restarting print spooler service and re-installing office but this has come to no avail,
    any ideas would be much appreciated!

    Hi,
    This issue occurs because the Page Setup settings that you specify in your file override the settings that you specify in the printer driver properties.
    To work around this issue, do not specify the paper size, page orientation, or page margins in the printer driver properties. Instead, specify these settings in your workbook.
    To specify these settings, follow these steps:
    1.Start Excel, and then open the workbook you want to change.
    2.In Microsoft Office Excel 2010, click the sheet that you want to print, and then click the Page Layout tab. In the Page Setup group, click Page Setup to open the Page Setup dialog box.
    3.Click the Page tab.
    4.Under Paper size, click the paper size that you want.
    5. Click Options button and in Printing Shortcuts tab, in the Paper source area, perform one of the following steps:  ◦If the printer can automatically select the correct paper tray to use, click Default tray in the First page list, and then click Default
    tray in the Other pages list.
    Default tray is the default setting in both of these lists.
    ◦If the printer cannot automatically select the correct paper tray to use, you may have to select the paper tray that contains the paper size that you selected in step 4.
    To do this, click the appropriate paper tray in the First page list and in the Other pages list.
    6.If you want to change the page orientation or its page margins, click the Finishing tab.
    7.Select the options that you want.
    8.Click OK.
    9.Repeat steps 2 to 8 for each sheet of your workbook for which you want to specify settings.
    Jaynet Zhang
    TechNet Community Support

  • Why is the software update not showing up in general settings?

    Why does my software update not show up in general settings?

    If you have an iPad 1, the max iOS is 5.1.1. For newer iPads, the current iOS is 7.1.1. The Settings>General>Software Update only appears if you have iOS 5.0 or higher currently installed.
    You can no longer update to iOS 6.x, or down grade the iOS.
    iOS 5: Updating your device to iOS 5 or Later
    http://support.apple.com/kb/HT4972
    How to install iOS 6
    http://www.macworld.com/article/2010061/hands-on-with-ios-6-installation.html
    iOS: How to update your iPhone, iPad, or iPod touch
    http://support.apple.com/kb/HT4623
    If you are currently running an iOS lower than 5.0, connect the iPad to the computer, open iTunes. Then select the iPad under the Devices heading on the left, click on the Summary tab and then click on Check for Update.
    Tip - If connected to your computer, you may need to disable your firewall and antivirus software temporarily.  Then download and install the iOS update. Be sure and backup your iPad before the iOS update. After you update an iPad (except iPad 1) to iOS 7.x, the next update can be installed via wifi (i.e., not connected to your computer).
    Tip 2 - If you're updating via wifi, place your iPad close to your router to preclude getting a corrupted download.
    How to Upgrade to iOS 7
    The iOS 7.0 update requires around 2.5 GB of storage space, so if your iPad is almost full, you may need to clear up some space. You can check your available space in Settings -> General -> Usage.
    There are two ways to upgrade to iOS 7: You can use your Wi-Fi connection, or you can connect your iPad to your PC and update through iTunes. We'll go over each method.
    To upgrade using Wi-Fi:
    Note: If your iPad's battery is under 50%, you will want to plug it into your charger while performing the update.
    Go into the iPad's Settings.
    Locate and tap "General" from the menu on the left.
    The second option from the top is "Software Update". Tap this to move into the update settings.
    Tap "Download and Install". This will start the upgrade, which will take several minutes and will reboot your iPad during the process. If the Download and Install button is grayed out, trying clearing up some space. The space required by the update is mostly temporary, so you should gain most of it back after iOS 7 is installed.
    Once the update is installed, you may have to run through the initial steps of setting up your iPad again. This is to account for new features and settings.
    To upgrade using iTunes:
    First, connect your iPad to your PC or Mac using the cable provided when you purchased your device. This will allow iTunes to communicate with your iPad.
    You will also need the latest version of iTunes. Don't worry, you will be prompted to download the latest version when you launch iTunes. Once it installs, you may be asked to setup iCloud by logging into your iTunes account. If you have a Mac, you may be prompted on whether or not you want to enable the Find my Mac feature.
    Now you are ready to begin the process:
    If you upgraded iTunes earlier, go ahead and launch it. (For many, it will launch automatically when you plug in your iPad.)
    Once iTunes is launched, it should automatically detect that a new version of the operating system exists and prompt you to upgrade to it. Choose Cancel. Before updating, you will want to manually sync your iPad to make sure everything is up to date.
    After canceling the dialog box, iTunes should automatically sync with your iPad.
    If iTunes doesn't automatically sync, you can manually do it by selecting your iPad within iTunes, clicking on the File menu and choosing Sync iPad from the list.
    After your iPad has been synced to iTunes, select your iPad within iTunes. You can find it on the left side menu under Devices.
    From the iPad screen, click on the Update button.
    After verifying that you want to update your iPad, the process will begin. It takes a few minutes to update the operating system during which time your iPad may reboot a few times.
    After updating, you may be asked a few questions when your device finally boots back up. This is to account for new settings and features.
     Cheers, Tom

  • When I open E12 to print, the printer settings do not reflect my default printer settings.

    When I open E12 to print, the printer settings do not reflect my default printer settings.  After I change the settings in E12 and print and close, when I reopen E12 the printer settings are back to what E12 originally decided they were.  What am I missing?

    Not on the list for supported printers http://support.apple.com/kb/ht4356

  • I have a Canon LBP5360 laser printer connected via USB cable to my MacPro running 10.6.8  I have downloaded the latest UFR2 divers. I am trying to connect to the printer but the printer is not showing appearing in Print

    I have a Canon LBP5360 laser printer connected via USB cable to my MacPro running 10.6.8 
    I have downloaded the latest UFR II driver. (UK Version)
    I am trying to connect to the printer but the printer is not  appearing in my Print/Fax Preferences.
    When I click the box "More Printers" under the Default printer the drop down box gives me a heading "Canon IPv6 (UFRII) with the option to add or cancel. (The add is highlighted). But there are no printers showing in the box. Nothing. Can anyone help?
    Is there a problem with my Mac setup or maybe a setting in my printer?

    Mac UFR II Printmonitor
    UFR II Printmonitor is application software that interfaces with the software for the printer, and is installed with the printer driver. You can start UFR II Printmonitor in the following folder to check the printer status, and errors. Refer to the Help how to use the Print Monitor.
    MF3010, MF8000 Series, MF8000C Series, MF8300 Series, MF8300C Series:
    Print Monitor: [Library] - [Printers] - [Canon] - [CUPSCMFP] - [Utilities]
    Other Printers:
    Print Monitor: [Library] - [Printers] - [Canon] - [UFR2] - [Utilities]

Maybe you are looking for