CE Standby Config and Firewalls

Hi,
I've a problem getting a CE 7305 with standby config to work. The problem seems to be related to firewall where the ip default-gateway is pointing to. If I point the ip default-gateway (DG)to another router in this segment the standy works properly. If I do a ping on the FW I see an arp-entry in the CE but I don't get a response.
Pointing back the DG to the firewall the standby works for some seconds but afterwards no link is active. What do I have to permit on the FW to have the FW as default GW? Is a permit ICMP standby ip of the CE to the default GWs IP-Adresse enough or should this work without any permission on the FW-side. Btw the FW is a Cat6k with the Firewall blade.
Kind Regards,
Joerg

Make sure the inside IP addresses are permitted on the firewall. I don't think you need to have a special configuration on the firewall for it to work as a default gateway. You could check for bugs in the Bugtool kit to rule out any known issue.

Similar Messages

Firefox will open 4 or 5 tabs fine, but then will not load any further websites after those first 4 or 5, or allow you to refresh one of those first tabs -- including about:config and the addon page

Firefox 5 worked fine. I installed Firefox 7, and when I ran it, tabs would just say "connecting to..." and hang. Restarting did not help. Websites open fine in IE and Chrome. Disabled all firewalls and antivirus, did not help. Uninstalled and reinstalled Firefox 5, everything worked fine again. This was using Vista 64-bit.
Upgraded to Windows 7, uninstalled Firefox 5, installed Firefox 7, had same problem. Uninstalled Firefox 7 completely (including the profile information, I saved that information in another folder), restarted computer, and installed Firefox 7 using a completely clean profile. Did not install any add-ons, checked to make sure all plug-ins were up-to-date, and updated plugins.
Now when I start Firefox, I can load 3 or 4 or 5 tabs fine -- after those first few tabs are open, I cannot open or refresh any other tabs -- including about:config and the add-on manager -- I have to restart Firefox. The hangup doesn't appear to be related to what websites I am attempting to open, but it looks like the number is the problem. I have run through all of the FAQ procedures, including changing the max number of network connections to 48, and the problem does not seem to go away.
As a side note, I had this same problem when I tried to go from version 5 to version 6 as well. Version 5 is the most recent version that worked on my system.

Can you try Aurora - download it from http://www.mozilla.org/en-US/firefox/channel/
And let us know how it works.

Lenovo Yoga 2 13, Kali Linux 1.0.7, Ubuntu 14.04, Windows 8.1 install, config, and wifi fix.

Lenovo Yoga 2 13, Kali Linux 1.0.7, Ubuntu 14.04, Windows 8.1 install, config, and wifi fix.
I wanted to share an experience with everyone I hope will help others avoid what I have gone through the past 3 days. I bought a Yoga 11s that I loved but had some issues with the wireless, Lenovo being awesome replaced it with a Yoga 2 13. I love this laptop but ran into some issues with Linux install/wireless, which I wanted to show how to resolve in one place. Hopefully this will help someone else get through this quicker
I am going to try and write this for someone with little Linux experience, if I miss the mark please let me know and I will clarify the best I can.
For work I need Windows 8.1 and Kali Linux, while for home I prefer Ubuntu.
My Yoga 2 13:
I5 1.6 ghz
8 GB ram
256 GB SSD
ORANGE!
My requirements:
I need Windows
I need Kali Linux (livecd, even with persistent mode was not an option as it would not save the wireless fix or system updates) – I would also like this on a USB drive and not the internal SSD
I would like Ubuntu
Needed to do this:
1. 2 USB thumb drives (at least 8gb in size each) I used 2 Leef Supra 32GB drives. They are my favorite right now and are only about $27 at amazon.
2. Phone that can USB Tether or a USB Ethernet card (External USB wireless will show as "Hardware Locked"). Again you can pick one up for sub $10 if you need the USB Ethernet route. I used my Galaxy S5, you will need to download 200-300 mb of items through this so make sure you have the data if you go that route.
3. You may be able to get a USB wifi card to work if you do the following after boot. This only worked once for me.
                a.Type ‘sudo rmmod iwlmvm’
b.Type ‘sudo rmmod iwlwifi’
4. ISOs of Ubuntu and Kali Linux (I used Ubuntu 14.04 and Kali Linux 1.0.7)
5. Software to unzip the ISOs. I recommend 7-ZIP and will be referencing this in this guide.
6. I will include the EFI boot files and the WiFi fix files if I can attach. Otherwise I will provide a link to them.
   Link: https://www.dropbox.com/s/puxnnoft3gn2b6l/WiFiFix.zip
Recommended (these are just in case you corrupt something making your system not see any OS
1. I would call Lenovo beforehand and get a set of recover disks (this will take 2-3 days)
2. In the meantime a USB Windows 8.1 or 8 ISO (the repair feature may save you)
*Note: At many points in this guide I detail steps and commands. Please double check that you understand the step before proceeding. There are multiple points where a mistyped command or clicking the wrong option will cause your entire system to fail and you will need to reformat the entire drive and start over. This also will make One Touch recovery not work. Proceed with caution.*
I did not need to disable ‘secure boot’ to do this, but keep in mind that you may need to.
Steps:
First let’s go through the installs, and then we will go through grub config and wireless fix
1. In Windows scroll to computer and right click, select manage.
2. Go to “Disk Management”
3. Select the main HDD (notice Lenovo puts a stupid number of partitions on here)
a. I deleted the D: drive on here, if you do this make sure to copy the drives over to your main C: drive. You will want to run each of the installers and repair the drivers after.
4. I used the space from the D: drive and pulled a little more creating a 50 GB partition for Ubuntu and my swap file
a. You can also add more space by right clicking your C drive and selecting shrink
b. Do not format the partitioned data as this will make identifying it later much easier.
5. Open a command line
                a. Swipe from the right of the screen and select search
                b. Type ‘cmd’
                c. right click and select ‘run as admin’
6. For Ubuntu: Type ‘diskpart’ into the command line
                a. type ‘list disk’
i. You should see 2-3 disks depending on if you have one or both usb drives in the laptop at the time. I would suggest only doing 1 at a time so you don’t lose track.
                b. type ‘select disk $’ (Replace the $ with the number of the drive)
c. ***** Before proceeding make sure you have the correct drive selected or you can ruin your Windows install and Lenovo one touch recovery will not fix it since we have changed the partitions *****
d. type ‘clean’
e. type ‘create partition primary’
f. type ‘active’
g. type ‘format fs=fat32 quick’
h. type ‘assign’
i. type ‘exit’
6. For Kali Linux: Type ‘diskpart’ into the command line
                a. type ‘list disk’
i. You should see 2-3 disks depending on if you have one or both usb drives in the laptop at the time. I would suggest only doing 1 at a time so you don’t lose track.
                b. type ‘select disk $’ (Replace the $ with the number of the drive)
c. ***** Before proceeding make sure you have the correct drive selected or you can ruin your Windows install and Lenovo one touch recovery will not fix it since we have changed the partitions *****
d. type ‘clean’
e. type ‘create partition primary size= 3272
f. type ‘active’
g. type ‘format fs=fat32 quick’
h. type ‘assign’
i. type ‘exit’
j. By doing this we can maintain a portion of this drive as the install CD and still have linux install/ liveCD if we need to run it on another machine.
7. At this point the drive is ready to have the contents of the ISO copied over.
8. Right click the ISO and select 7-zip then ‘zip to /’ This should unzip the ISO to the location of the ISO into a folder named exactly the same as the ISO.
9. Once this is done for Ubuntu ISO it is done
10. Kali requires a little bit more to be ready
                a. Kali will need some files added for EFI boot. --$--
                               i. Thanks to: https://forums.kali.org/showthread.php?271-How-to-EFI-install-Kali-Linux
                               ii. EFI files are located within the wifi fix folder https://www.dropbox.com/s/puxnnoft3gn2b6l/WiFiFix.zip
11. Now let’s start with Ubuntu
Ubuntu install
1.     Place USB drive into the laptop and press the “Lenovo boot” button next to the power button
2.     Select ‘Boot Menu’
3.     Select ‘EFI USB Device (Name of drive)’ Mine stated Leef Supra
4.     Select ‘install Ubuntu’
5.     Go through the Ubuntu install until you get to select the install drive
6.     Once you get to the install portion it will ask you to select from one of 4 options. Select ‘Manually select partition’
7.     Select the “Free Space” where we opened up some of the drive
8.     You will need to create 2 partitions, I usually create the swap partition at the end of the drive
a.     First I create the swap
                                          i.    Set at the end of the drive
                                         ii.    Set size to 1024 mb
                                        iii.    Set type to ‘swap’
b.     Second create the ext 4 partition
                                          i.    Set to beginning of drive
                                         ii.    Set to remainder of the space
                                        iii.    Set type to ext4
                                        iv.    Set mount point to /
9.     Finish the install and boot into Ubuntu
10.   You will notice that your wireless is ‘disabled by hardware’ This is fine for the time being and we will worry about this after the kali install. If we fix it now for some reason after installing kali we get the error again and would just need to fix it again.
Kali Linux install
1.     Place USB drive into the laptop and press the “Lenovo boot” button next to the power button
2.     Select ‘Boot Menu’
3.     Select ‘EFI USB Device (Name of drive)’ Mine stated Leef Supra
4.     From the grub menu select ‘install kali linux’ both graphical and text work. I much prefer text install
5.     You will get a few errors through the install but that is fine
6.     The first we see is about network hardware and ‘load missing firmware from removable media?’ – Select ‘no’
7.     Then select no ethernet card
8.     It will have you name your machine then it will ask you for the root password
a.     If you want to just use root *not recommended* place the password here
b.     If you wish to use a non-root account then leave these blank and it will ask you for a name, username, and password of the new machine *Very Recommended* - this will also add this user to the sudoers file
9.     It will then ask you to ‘partition disks’
10.   Select manual
11.   Now here is where it can get a little confusing so read twice click once
12.   Select the USB drive from this list
13.   Mine shows up under (sdb) – Leef Supra
a.     It could be sdc, sdd, sde, etc… depending on how many drives you have plugged in.
14.   You should see one primary drive that is 3gb or so that is formatted as FAT32. – DO NOT TOUCH THIS PARTITION!
15.   You should see the remainder of this drive as ‘FREE SPACE’ select that
16.   Create a partition at the end at size 1024mb and swap
17.   Then create another one for the remainder of the drive and set it to ext4 with mountpoint of /
18.   Continue through the install after you should see an error warning you that ‘you may not be able to boot’ that is fine, select continue
19.   Then select from the menu of all the options ‘continue without bootloader’
20.   It should finish up then reboot on its own.

First setup/boot/fix grub
1.     You should be able to boot up into GRUB2 menu now.
2.     You may not see kali linux in this menu (make sure you have your towel and don’t panic!)
3.     Boot into Ubuntu
4.     Once you log in you should see that you still cannot use wireless due to being locked by hardware
5.     This is expected
6.     Let’s fix grub then we will come back to fixing wireless
7.     Plug in your device to connect to the internet (USB Tethering or USB Ethernet)
8.     Once you verify that you now have an internet connection run the following from terminal
a.     ‘sudo add-apt-repository ppa:danielrichter2007/grub-customizer’
b.     ‘sudo apt-get update’
c.     ‘sudo apt-get install grub-customizer’
9.     You can also edit the grub.cfg manually if you know what you are doing… I did not
10.   Open grub customizer
11.   It should auto populate and you should see ‘debian (kali linux)’ somewhere in the list
12.   It should be mounted to /dev/sdb2 or /dev/sdc2 depending on how many devices you have
13.   At this point go ahead and save
14.   Reboot and test that you can get into each OS
15.   This is where my inexperience got me. I spent 2 of my days so I am including this error: If when you boot into Kali you get an error somewhere that says ‘/bin/sh: can’t access tty: job control turned off’ look above it for an error that looks similar to ‘ALERT! /dev/sdc2 does not exist. Dropping to a shell!!’
a.     That error is due to the mount point being incorrect in grub, reboot and from within grub highlight the kali boot. Press ‘e’ then towards the bottom you should see ‘root=/dev/sdc2’ change this to ‘root=/dev/sdb2’ again the number doesn’t matter just make sure it stays the same.
b.     Press F10
c.     If this boots fine then you will need to go back and fix the grub.cfg or load into Ubuntu and open grub customizer again, it should fix this
16.   Now you have 3 working OS on the machine with one being on a USB! Congrats!
17.   You can remove the USB with no worry of screwing up your install, but you will not be able to boot into Kali Linux until you replace it. I would suggest only removing it and replacing it while the machine is powered off, but that’s just me.
Fix Wireless
Now is the time to do what probably ¾ of you came here for. FIX THE DANG WIRELESS. This is a huge problem from Lenovo’s side that I hope they realize how important Linux is and will fix. I won’t hold my breath though.
Log into Ubuntu : This is well documented in the following forum post on page 3 by user Haohe:
http://ubuntuforums.org/showthread.php?t=2215044&page=3
His has you download quite a large file, mine should be much smaller.
https://www.dropbox.com/s/puxnnoft3gn2b6l/WiFiFix.zip
1.     Download the attached package with the fix.
2.     Connect your USB internet device (tether or ethernet)
3.     Place the packages somewhere easy to access, in this example I will place them under ~/Desktop/WiFiFix
4.     Type ‘cd ~/Desktop/WiFiFix/’
5.     Now we need to prep the tools we need.
6.     Type ‘sudo apt-get update’ – we did this before, but you know, just in case
7.     Type ‘sudo apt-get install linux-headers-`uname –r`’   Note around uname-r they are the ` symbol not the ‘ this is located just above the tab on the same key as ~.
8.     Type ‘make’
9.     Type ‘sudo cp /lib/modules/3.13.0-24-generic/kernel/drivers/platform/x86/ideapad-laptop.ko ~/ideapad-laptop.ko.backup’
10.   Type ‘sudo cp ~/Desktop/WiFiFix/ideapad-laptop.ko /lib/modules/3.13.0-24-generic/kernel/drivers/platform/x86/’
11.   Type ‘sudo modprobe -r ideapad-laptop’
12.   Type ‘sudo modprobe ideapad-laptop’
13.   Type ‘sudo rfkill unblock all’
14.   Type ‘sudo modprobe -r ideapad-laptop’
15.   Type ‘sudo mv ~/ideapad-laptop.ko.backup /lib/modules/3.13.0-24-generic/kernel/drivers/platform/x86/ideapad-laptop.ko’
16.   Next we need to blacklist the ideapad module
17.   Type ‘sudo echo 'blacklist ideapad-laptop' > /etc/modprobe.d/blacklist-ideapad.conf’
a.     The first time I tried this it wouldn’t work. So I did the following
b.     ‘sudo touch /etc/modprobe.d/blacklist-ideapad.conf’
c.     ‘sudo vim /etc/modprobe.d/blacklist-ideapad.conf’
d.     Enter     blacklist ideapad-laptop
e.     Exit and save
18.   Reboot your Yoga 2 13
19.   Boot into kali and see if you have wireless, if you do then you are done. If not we will need to repeat this process with one small little change.
Kali Wifi Fix
1.     Copy the sources.list from the package provided
2.     Replace /etc/apt/sources.list with the included
3.     Some of the file path changes but the process remains the same from here.
Congratulations you now have 3 OSes one portable to other machines and working wifi!
Thank you
SirGed

I dont know why the battery life of my iphone 4 is so low ! i really want to know how many hours i'll have if it's on standby. And how many hours if i use it normally for music and facebook (sometimes a little bit games)

i dont know why the battery life of my iphone 4 is so low ! i really want to know how many hours i'll have if it's on standby. And how many hours if i use it normally for music and facebook (sometimes a little bit games) !!!

to enhance your battery life, keep screen display to minimum, set screen lock automatically after 1 min, select internet notifications to off.

Document management system configs and status

Can anybody tell me the configs and flow of document status and document version in DMS....
Vijay

Hi Vijay,
Document Versioning in DMS can be controlled as per the following selection criteria,
Value Description
0 No version numbers
1 Numeric version numbers 00 .. 99
2 Numeric version numbers 01 .. 99
3 Alphanumeric numbers A0 .. Z9
4 Alphanumeric numbers A1 .. Z9
5 Alphanumeric numbers AA .. ZZ
6 AA .. AZ,A0 .. A9;BA .. Z9
7 as 6, but without 0
8 _A .. Z ; AA .. Z9
9 as 5, but 00 allowed
A as 6, but 00 allowed
for USER-EXIT
in dc10, the number which u select automatically controls the version each time you create a document under same document number/doc type/doc part.
if you need to create a document under user-defined version or manually entered number then you can choose ur version which lies between the range selected.
There is no such unlock status displayed on Document info record (DIR).
beside document status you can see something called as "Not Released" indicator in red colour.
the document status changes from "Not Released" to "Released" once the status is set in which setting is done.
for configuration,
dc10>select doc type>click on define document status-->create new statuses if required/double click on the final status (say Released) and set the status "Release Flag".
under "Status type set to 'S' locked status".
save and create a document.
prior you need to set the status network using system defined statuses or even you can create your own user defined statuses.
once the status is set to Released, automatically document will set to Released along with the release date and also it will get locked so dat it cannot be further edited by anyone.
Thank You,
Manoj
Pl. reward if useful.

HP printer and Firefox 4.0.1 not talking....prints from Explorer fine..help, I have reset the printer in config and updated all plugins...still not working. I want to use firefox but can't if I can not get this issue solved.

I have tried the obvious....CP and made sure the correct printer was selected and it wasn't set to print to file. I then did the about:config and reset the printer. I have also updated all the plugins with none of the solutions working.
Please help...I really don't want to have to use Explorer everytime I need to print something.

See [/questions/805889]

Archived log file are not shifted to standby side and applied

Hi Guru's,
DB
My OS Version:Windows Server 2003
DB Version:11.2.0.1.0
I am trying to create Physical Standby DB on my test machine after setting all the parameters and start standby db in mount mode when i do the verification of archived log files that need to be shift from pri site to standby site i am getting:
no rows selected.
I am following the below mentioned doc for reference
http://docs.oracle.com/cd/E11882_01/server.112/e25608/create_ps.htm#i63561
Can anyone from your side can help me to sort out this problem.
Thanks in advance

vk82 wrote:
SQL> select max(sequence#) from v$archived_log;
MAX(SEQUENCE#)
39
SQL> select process,status,sequence# from v$managed_standby;
PROCESS STATUS SEQUENCE#
ARCH CLOSING 38
ARCH CLOSING 36
ARCH CONNECTED 0
ARCH CLOSING 37
SQL> select max(sequence#) from v$archived_log where applied='YES';
MAX(SEQUENCE#)
39
Yes the max sequence generated on primary is same as the max sequence applied on standby.
And what is MRP and why it is important can you please let me know abt thisWhenever you created standby database, Make a habit of tail to alert log file to monitor whats happening on the standby database, Besides MRP is an Media Recovery Process , which applies archies/redo on standby database.
MRP can apply based on the redo transport, If you are using real-time apply then Redo will be writtened to the standby redo log files at the same time recovery will be performed by MRP process, If you are not using Real-Time apply then whenever a archive generated on primary that archive will be transported to the standby and applied on the standby database.
It is recommended to use Realtime apply, so that you can avoid much data lost.
However you are in 11gR2, You can use below query to monitor
SQL> SELECT * FROM V$STANDBY_EVENT_HISTOGRAM WHERE NAME = 'apply lag' AND COUNT > 0;
NAME             TIME UNIT                  COUNT LAST_TIME_UPDATED
apply lag           0 seconds                 431 08/05/2012 22:14:21
apply lag           1 seconds                   7 08/05/2012 22:13:31
SQL>Edited by: CKPT on Nov 6, 2012 6:49 PM

How do I get about:config and other about: addresses to drop down from URL bar?

How do I get about:config and other about: addresses to drop down from URL bar?
It's a pain having to retype them in full... not sure why there is no easier interface to them.

hello, you can bookmark the sites for faster access.
[[How to use bookmarks to save and organize your favorite websites]]

My iPhone turns off whenever it goes into standby mode and has to be turned back on to work

My iPhone turns off whenever it goes into standby mode and has to be turned back on to work

That's normal behavior. It turns off automatically in order to preserve the battery. Pushing the On/Off button turns it on immediately. This also requires entering the passcode and prevents the phone from being accessed by anyone but you.

About:config and bold text

I have noticed that showing ALL bookmarks is very slow.
I understand that Firebug is sometimes cause for slow behaviour as posted on some notices for applications.
I like to check why is this and disabled some Ads-on.
Issue is what is actually about:config and bold text like:
accessibility.typeaheadfind.flashBar;0
Is it bold text warning that something is wrong?
Ref:I have upgraded to new version 9.beta4

No bold text in about:config means that the value it has modified from you or from a add-on or for a program that related with firefox(flash or anything)......
http://kb.mozillazine.org/Accessibility.typeaheadfind.flashBar
if you like to read about:config:
http://kb.mozillazine.org/About:config_entries
probably the browsing some times are slow because as you allready known 9.0 is a beta version, and for the reason you tell us, Firebug.
thank you
Please mark "Solved" the answer that really solve the problem, to help others with a similar problem.

Need of SAP Equipment and Tooling Managemt Config and End user documents

Hi
I am in implementation project of SAP PM - ETM (Equipment and Tooling Managemt )
Can any body please send Config and end user documents if any?
I am in urgent need of those documents
Thanks in Advance.
SR

Hello Jackie,
The new features are outlined in the Installation Guide (page 10.)
The most noticable to the end-users would be the security settings and the different views such as Hierarchial and Tree views
which can be customised.
Best Regards,
Jude Bradley

Required Config and testing Docs for cash management/cash forecasting

Hi All,
My client need to implement cash management/cash forecasting ..
Can anyone send the details Required Config and testing Docs for the same as earlier i have not worked in this area..
Thanks in advance...
Regards,
Sandip

Hello
Please check the below link
help.sap.com/bp.../J11_BB_ConfigGuide_EN_IN.doc - United States
Thanks & Regards
Phaneendra

I went into about:config and there is no conduit in there but I know it is because it is in my startup

I am going nuts with this damn conduit malware. I have tried everything. This morning when I got up it seemed as though my whole computer crashed. It wouldn't even go on. I unplugged a couple of plugs for a while, and lo and behold it came on. Whew!!
I went into about:config and there was nothing in there with conduit. However, it is in my startup in MsConfig. And I know that is what is giving me so many problems. I did see something in there that I wanted to get out, but it wouldn't let me. How can I do that????
BevM
<sub>edit: removed your mail address from public display, since the only thing it will attract are spam bots. you will be notified per mail once somebody replies to the thread. (philipp)</sub>

Hello,
That depends on which ones you use. HitmanPro has a trial period, so you can uninstall once you get rid of your problem (there is no permanent free version for it).
However, [http://www.malwarebytes.org/products/malwarebytes_free/ MalwareBytes' Anti-Malware] and [http://general-changelog-team.fr/en/downloads/viewdownload/20-outils-de-xplode/2-adwcleaner AdwCleaner] have free versions - you do not need to use the trial period/pay for those ones. For MalwareBytes, the last dialog box in the installation will ask you to start the Free Trial period of the Premium version, '''uncheck that box''' so that it remains as the free version. I think even if you choose to use the trial, you can revert back to the free version later.

SECURITY PATCH ON STANDBY DATABASE AND PRIMARY DATABASE

I have a question on applying CPU on standby and primary database
I have a standby database on machine2 and primary on machine1
I applied a CPU patch on the Oracle Home of Standby database and
did not run the catcpu.sql as standbydatabase is in mount state.
Now i am going to apply the CPU patch on primary database.
What i need to confirm is that after i apply the patch on primary database oracle home
and run the cat cpu.sql on that do i have to do anything on the standby database
for instance rebuilding it or something or the change would be shipped to the standby
server automatically.
The purpose is to have the primary and standby database on the same patch level
in case of a failover
Please let me know asap

Any one has any idea on this. Any ideas would be appreciated

Webutil - Config and Jar Files

Hi List,
I am using Webutil for the first time .I have downloaded demo from OTN .WHich has pll,olb,jar ,dll files.I have gone through the manual following few things are still not clear
1.where to store/keep Webutil.config and how do we refer to that file .
2.If Formsweb.confog required? are these both config files required and where to keep and how do we give path to these two files
3.how to refer webutil.jar file.which path these jar files needed to be kept ? do we have to unjar or something ?
Thanks in advance
Regards
Sripad

1.where to store/keep Webutil.config and how do we refer to that file .
A: you decide and configure the webutil required file location saccordingly. I would suggest to store the webutil directory in the forms90 directory for simplicity
2.If Formsweb.confog required? are these both config files required and where to keep and how do we give path to these two files
A: Forms basic knowledge: The formsweb.cfg file and the default.env file are used by Forms - unless configured otherwise - to define the runtim environment (default.env) and the application runtime commands (formsweb.cfg). Both files are required and available in the forms90/server directory
3.how to refer webutil.jar file.which path these jar files needed to be kept ? do we have to unjar or something ?
Don't unjar. Copy the jar file to forms90/java. This way you van reference it by its name
archive= ... other files ..., webutil.jar
Frank

CE Standby Config and Firewalls

Similar Messages

Maybe you are looking for