Changing RADIUS Server
We have an AS5300 and a Radius server. We are changing the Radius server. Besides changing the IP address of the Radius server on the AS5300, is there anything else that we need to do? Thanks.
I dont think so, just specify the new IP and you are good to go.
check the following example:
aaa authentication login default group radius local
aaa authorization exec default group radius local
aaa authorization command 2 default group tacacs+ if-authenticated
radius-server host 172.16.71.146 auth-port 1645 acct-port 1646
radius-server attribute 44 include-in-access-req
radius-server attribute 8 include-in-access-req
So, unless you are changing port or other parameters, changing the IP will do the job.
HTH,
please rate all posts.
Vlad
Similar Messages
-
Change RADIUS Certificate or Reset RADIUS, SERVER 3.2.2
Hi All,
I've got an expiring self signed certificate that I was using for the RADIUS service on 10.9, server 3.2.2.
I can figure out how to replace this certificate with our valid trusted SSL certificate for our domain. We originally setup the RADIUS server with the instructions at https://www.yesdevnull.net/2013/10/os-x-mavericks-server-setting-up-freeradius/
If I just try to install new certs using sudo radiusconfig -installcerts command, it just breaks the radius.
I've also tried blowing away the radius folder inside of /Library/Server in an attempt to reset RADIUS to the factor defaults, but after reinstalling the server app, and going through the process of setting up RADIUS, it's still using the old certificate.
Any help would be appreciated!
ThanksThanks to Charles over at Krytped, deleting the Radius folder from /Library/Server/Radius and running this command:
sudo rm /var/db/.ServerSetupDone
Allowed me to get Server to recreate a clean Radius set. -
EAP-FAST on Local Radius Server : Can't Get It Working
Hi all
I'm using an 877w router (flash:c870-advsecurityk9-mz.124-24.T4.bin) as local radius server and have followed various config guides on CCO. LEAP works fine but I just can't get EAP-FAST to work.
I'm testing with win7 client using anyconnect secure mobility client, and also a mac book pro but without luck.
the router sees unknown auth type, and when I run some debugs it talks of unknown eap type 3
sh radius local-server s
Successes : 1 Unknown usernames : 0
Client blocks : 0 Invalid passwords : 0
Unknown NAS : 0 Invalid packet from NAS: 17
NAS : 172.27.44.1
Successes : 1 Unknown usernames : 0
Client blocks : 0 Invalid passwords : 0
Corrupted packet : 0 Unknown RADIUS message : 0
No username attribute : 0 Missing auth attribute : 0
Shared key mismatch : 0 Invalid state attribute: 0
Unknown EAP message : 0 Unknown EAP auth type : 17
Auto provision success : 0 Auto provision failure : 0
PAC refresh : 0 Invalid PAC received : 0
Can anyone suggest what I might be doing wrong?
Regs, TimThanks Nicolas, relevant snippets from config:
aaa new-model
aaa group server radius rad_eap
server 172.27.44.1 auth-port 1812 acct-port 1813
aaa authentication login eap_methods group rad_eap
aaa authorization exec default local
aaa session-id common
dot11 ssid home
vlan 3
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa
ip dhcp pool home
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 194.74.65.68 194.74.65.69
ip inspect name ethernetin tcp
ip inspect name ethernetin udp
ip inspect name ethernetin pop3
ip inspect name ethernetin ssh
ip inspect name ethernetin dns
ip inspect name ethernetin ftp
ip inspect name ethernetin tftp
ip inspect name ethernetin smtp
ip inspect name ethernetin icmp
ip inspect name ethernetin telnet
interface Dot11Radio0
no ip address
encryption vlan 1 mode ciphers aes-ccm tkip
encryption vlan 2 mode ciphers aes-ccm tkip
encryption vlan 3 mode ciphers aes-ccm tkip
broadcast-key vlan 1 change 30
broadcast-key vlan 2 change 30
broadcast-key vlan 3 change 30
ssid home
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0.3
encapsulation dot1Q 3
no cdp enable
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface Vlan3
no ip address
bridge-group 3
interface BVI3
ip address 192.168.1.1 255.255.255.0
ip inspect ethernetin in
ip nat inside
ip virtual-reassembly
radius-server local
no authentication mac
nas 172.27.44.1 key 0 123456
user test1 nthash 0 B151E8FF684B4F376C018E632A247D84
user test2 nthash 0 F2EEAE1D895645B819C9FD217D0CA1F9
user test3 nthash 0 0CB6948805F797BF2A82807973B89537
radius-server host 172.27.44.1 auth-port 1812 acct-port 1813 key 123456
radius-server vsa send accounting -
Cisco 28xx easy vpn server & MS NPS (RADIUS server)
Здравстуйте.
Имеется LAN (192.168.11.0/24) с граничным роутером cisco 2821 (192.168.11.1), на котором настроен Easy VPN Server с локальной авторизацией удаленных пользователей, использующих для подключения Cisco VPN Client v 5.0. Все работает. В той же LAN имеется MS Windows Server 2012 Essensial в качестве DC AD.
Возникла необходимость перенести авторизацию удаленных пользователей на RADIUS сервер. В качестве RADIUS сервера хочется использовать MS Network Policy Server (NPS) 2012 Essensial (192.168.11.9).
На сервере поднята соответствующая политика, NPS сервер зарегистрирован в AD, создан RADIUS-клиент (192.168.11.1), настроена Сетевая политика. В AD создана группа VPN-USERS, в которую помимо удаленных пользователей добавлен служебный пользователь EasyVPN с паролем "cisco".
Ниже выдежка из сонфига cisco 2821:
aaa new-model
aaa authentication login rausrs local
aaa authentication login VPN-XAUTH group radius
aaa authorization network ragrps local
aaa authorization network VPN-GROUP local
aaa session-id common
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 2
crypto isakmp client configuration address-pool local RAPOOL
crypto isakmp client configuration group ra1grp
key key-for-remote-access
domain domain.local
pool RAPOOL
acl split-acl
split-dns 192.168.11.9
crypto isakmp client configuration group EasyVPN
key qwerty123456
domain domain.local
pool RAPOOL
acl split-acl
split-dns 192.168.11.9
crypto isakmp profile RA-profile
description profile for remote access VPN
match identity group ra1grp
client authentication list rausrs
isakmp authorization list ragrps
client configuration address respond
crypto isakmp profile VPN-IKMP-PROFILE
description profile for remote access VPN via RADIUS
match identity group EasyVPN
client authentication list VPN-XAUTH
isakmp authorization list VPN-GROUP
client configuration address respond
crypto ipsec transform-set tset1 esp-aes esp-sha-hmac
crypto dynamic-map dyn-cmap 100
set transform-set tset1
set isakmp-profile RA-profile
reverse-route
crypto dynamic-map dyn-cmap 101
set transform-set tset1
set isakmp-profile VPN-IKMP-PROFILE
reverse-route
crypto map stat-cmap 100 ipsec-isakmp dynamic dyn-cmap
int Gi0/1
descrition -- to WAN --
crypto map stat-cmap
В результате на cisco вылезает следующая ошибка (выделено жирным):
RADIUS/ENCODE(000089E0):Orig. component type = VPN_IPSEC
RADIUS: AAA Unsupported Attr: interface [157] 14
RADIUS: 31 39 34 2E 38 38 2E 31 33 39 2E 31 [194.88.139.1]
RADIUS(000089E0): Config NAS IP: 192.168.11.1
RADIUS/ENCODE(000089E0): acct_session_id: 35296
RADIUS(000089E0): sending
RADIUS(000089E0): Send Access-Request to 192.168.11.9:1645 id 1645/61, len 103
RADIUS: authenticator 4A B1 DB 2D B7 58 B2 BF - 7F 12 6F 96 01 99 32 91
RADIUS: User-Name [1] 9 "EasyVPN"
RADIUS: User-Password [2] 18 *
RADIUS: Calling-Station-Id [31] 16 "aaa.bbb.ccc.137"
RADIUS: NAS-Port-Type [61] 6 Virtual [5]
RADIUS: NAS-Port [5] 6 1
RADIUS: NAS-Port-Id [87] 16 "aaa.bbb.ccc.136"
RADIUS: Service-Type [6] 6 Outbound [5]
RADIUS: NAS-IP-Address [4] 6 192.168.11.1
RADIUS: Received from id 1645/61 192.168.11.9:1645, Access-Reject, len 20
RADIUS: authenticator A8 08 69 44 44 8B 13 A5 - 06 C2 95 8D B4 C4 E9 01
RADIUS(000089E0): Received from id 1645/61
MS NAS выдает ошибку 6273:
Сервер сетевых политик отказал пользователю в доступе.
За дополнительными сведениями обратитесь к администратору сервера сетевых политик.
Пользователь:
ИД безопасности: domain\VladimirK
Имя учетной записи: VladimirK
Домен учетной записи: domain
Полное имя учетной записи: domain.local/Users/VladimirK
Компьютер клиента:
ИД безопасности: NULL SID
Имя учетной записи: -
Полное имя учетной записи: -
Версия ОС: -
Идентификатор вызываемой станции: -
Идентификатор вызывающей станции: aaa.bbb.ccc.137
NAS:
Адрес IPv4 NAS: 192.168.11.1
Адрес IPv6 NAS: -
Идентификатор NAS: -
Тип порта NAS: Виртуальная
Порт NAS: 0
RADIUS-клиент:
Понятное имя клиента: Cisco2821
IP-адрес клиента: 192.168.11.1
Сведения о проверке подлинности:
Имя политики запроса на подключение: Использовать проверку подлинности Windows для всех пользователей
Имя сетевой политики: Подключения к другим серверам доступа
Поставщик проверки подлинности: Windows
Сервер проверки подлинности: DC01.domain.local
Тип проверки подлинности: PAP
Тип EAP: -
Идентификатор сеанса учетной записи: -
Результаты входа в систему: Сведения об учетных данных были записаны в локальный файл журнала.
Код причины: 66
Причина: Пользователь пытался применить способ проверки подлинности, не включенный в соответствующей сетевой политике.
Игры с Cisco AV Pairs и прочими параметрами настройки Сетевой политики на RADIUS выдают аналогичный результат.
Штудирование "Network Policy Server Technical Reference" и "Configuring IPSec Between a Cisco IOS Router and a Cisco VPN Client 4.x for Windows Using RADIUS for User Authentication" Document ID: 21060 ответа не дали.
Если кто практиковал подобное, прошу дать направление для поиска решения.Going through your post, I could see that radius is sending access-reject because radius access-request is sending a vpn group name in the user name field. I was in a discussion of same problem few days before and that got resolved by making 2 changes.
replace the authorization from radius to local
and
changing the encryption type in transform set
However, in your configuration, your configuration already have those changes.
Here you can check the same : https://supportforums.cisco.com/thread/2226065
Could you please tell me what exactly radius server complaining? Can you please paste the error you're getting on the radius server.
~BR
Jatin Katyal
**Do rate helpful posts** -
EAP-TLS with Radius Server configuration (1130AG)
Hi All,
Im currently tryign to get eap-tls user certificate based wireless authentication working. The mismatch of guides im trying to follow has me ocming up trumps with success so far, so heres hoping you guys can right me wrongs and put me on the right path again.
My steps for radius:- (i think this part ive actually got ok)
http://technet.microsoft.com/en-us/library/dd283091(v=ws.10).aspx
Steps for the wirless profile on a win 7 client:- this has me confused all over the place
http://technet.microsoft.com/en-us/library/dd759246.aspx
My 1130 Config:-
[code]
Current configuration : 3805 bytes
! Last configuration change at 11:57:56 UTC Fri Jan 25 2013 by apd
! NVRAM config last updated at 14:43:51 UTC Fri Jan 25 2013 by apd
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname WAP1
aaa new-model
aaa group server radius RAD_EAP
server 10.1.1.29 auth-port 1812 acct-port 1813
aaa authentication login default local
aaa authentication login EAP_LOGIN group RAD_EAP
aaa authorization exec default local
aaa authorization network default local
aaa session-id common
ip domain name ************
dot11 syslog
dot11 ssid TEST
authentication open eap EAP_LOGIN
authentication network-eap EAP_LOGIN
guest-mode
crypto pki trustpoint TP-self-signed-1829403336
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1829403336
revocation-check none
rsakeypair TP-self-signed-1829403336
quit
username ***************
ip ssh version 2
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid TEST
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
ssid TEST
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.1.2.245 255.255.255.0
ip helper-address 10.1.1.27
no ip route-cache
no ip http server
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
radius-server host 10.1.1.29 auth-port 1812 acct-port 1813 key **************
radius-server key ************
bridge 1 route ip
line con 0
logging synchronous
transport preferred ssh
line vty 0 4
logging synchronous
transport input ssh
sntp server 130.88.212.143
end
[/code]
and my current debug
[code]
Jan 25 12:00:56.703: dot11_auth_send_msg: sending data to requestor status 1
Jan 25 12:00:56.703: dot11_auth_send_msg: Sending EAPOL to requestor
Jan 25 12:00:56.703: dot1x-registry:registry:dot1x_ether_macaddr called
Jan 25 12:00:56.703: dot11_auth_dot1x_send_id_req_to_client: Client 74de.2b81.56c4 timer started for 30 seconds
WAP1#
Jan 25 12:01:26.698: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,TIMEOUT) for 74de.2b81.56c4
Jan 25 12:01:26.698: dot11_auth_dot1x_send_client_fail: Authentication failed for 74de.2b81.56c4
Jan 25 12:01:26.698: dot11_auth_send_msg: sending data to requestor status 0
Jan 25 12:01:26.698: dot11_auth_send_msg: client FAILED to authenticate 74de.2b81.56c4, node_type 64 for application 0x1
Jan 25 12:01:26.699: dot11_auth_delete_client_entry: 74de.2b81.56c4 is deleted for application 0x1
Jan
WAP1#25 12:01:26.699: %DOT11-7-AUTH_FAILED: Station 74de.2b81.56c4 Authentication failed
Jan 25 12:01:26.699: dot11_aaa_upd_accounting: Updating attributes for user: 74de.2b81.56c4
Jan 25 12:01:26.699: dot11_aaa_upd_accounting: Updating attributes for user: 74de.2b81.56c4
Jan 25 12:01:26.699: dot11_auth_client_abort: Received abort request for client 74de.2b81.56c4
Jan 25 12:01:26.699: dot11_auth_client_abort: No client entry to abort: 74de.2b81.56c4 for application 0x1
Jan 25 12:01:27.580: AAA/BIND(000000
WAP1#12): Bind i/f
Jan 25 12:01:27.580: dot11_auth_add_client_entry: Create new client 74de.2b81.56c4 for application 0x1
Jan 25 12:01:27.580: dot11_auth_initialize_client: 74de.2b81.56c4 is added to the client list for application 0x1
Jan 25 12:01:27.581: dot11_auth_add_client_entry: req->auth_type 0
Jan 25 12:01:27.581: dot11_auth_add_client_entry: auth_methods_inprocess: 2
Jan 25 12:01:27.581: dot11_auth_add_client_entry: eap list name: EAP_LOGIN
Jan 25 12:01:27.581: dot11_run_auth_methods: Start aut
WAP1#h method EAP or LEAP
Jan 25 12:01:27.581: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
Jan 25 12:01:27.581: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to 74de.2b81.56c4
Jan 25 12:01:27.581: EAPOL pak dump tx
Jan 25 12:01:27.581: EAPOL Version: 0x1 type: 0x0 length: 0x002B
Jan 25 12:01:27.581: EAP code: 0x1 id: 0x1 length: 0x002B type: 0x1
01801670: 0100002B 0101002B ...+...+
01801680: 01006E65 74776F72 6B69643D 54455354 ..networkid=TEST
WAP1#
01801690: 2C6E6173 69643D41 50445741 50312C70 ,nasid=WAP1,p
018016A0: 6F727469 643D30 ortid=0
Jan 25 12:01:27.582: dot11_auth_send_msg: sending data to requestor status 1
Jan 25 12:01:27.582: dot11_auth_send_msg: Sending EAPOL to requestor
Jan 25 12:01:27.582: dot1x-registry:registry:dot1x_ether_macaddr called
Jan 25 12:01:27.583: dot11_auth_dot1x_send_id_req_to_client: Client 74de.2b81.56c4 timer started for 30 seconds
WAP1#
[/code]
Can anyone point me in the right direction with this?
i also dont like it that you can attempt to join the network first before failing
can i have user cert based + psk? and then apply it all by GPO
Thanks for any helpok ive ammdened the wireless profile as suggested
i already have the root ca and a user certificate installed with matching usernames
I had already added the radius device to the NPS server and matched the keys to the AP
now heres the debug im getting, when i check the NPS server, still doesnt look like its getting any requests at all :|
Jan 29 11:53:13.501: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,TIMEOUT) for 74de.2b81.56c4
Jan 29 11:53:13.501: dot11_auth_dot1x_send_client_fail: Authentication failed for 74de.2b81.56c4
Jan 29 11:53:13.501: dot11_auth_send_msg: sending data to requestor status 0
Jan 29 11:53:13.501: dot11_auth_send_msg: client FAILED to authenticate 74de.2b81.56c4, node_type 64 for application 0x1
Jan 29 11:53:13.501: dot11_auth_delete_client_entry: 74de.2b81.56c4 is deleted for application 0x1
Jan
WAP1#29 11:53:13.501: dot11_mgr_disp_callback: Received message from Local Authenticator
Jan 29 11:53:13.501: dot11_mgr_disp_callback: Received FAIL from Local Authenticator
Jan 29 11:53:13.501: dot11_mgr_sm_run_machine: Executing Action(BRIDGE,AUTHENTICATOR_FAIL) for 74de.2b81.56c4
Jan 29 11:53:13.502: dot11_mgr_sm_send_client_fail: Authentication failed for 74de.2b81.56c4
Jan 29 11:53:13.502: %DOT11-7-AUTH_FAILED: Station 74de.2b81.56c4 Authentication failed
Jan 29 11:53:13.502: dot11_mgr_disp_auth_abort
WAP1#: Sending abort request for client 74de.2b81.56c4 to local Authenticator
Jan 29 11:53:13.502: dot11_auth_client_abort: Received abort request for client 74de.2b81.56c4
Jan 29 11:53:13.502: dot11_auth_client_abort: No client entry to abort: 74de.2b81.56c4 for application 0x1
Jan 29 11:53:14.619: AAA/BIND(00000019): Bind i/f
Jan 29 11:53:14.619: dot11_mgr_disp_auth_request: Send auth request for client 74de.2b81.56c4 to local Authenticator
Jan 29 11:53:14.619: dot11_auth_add_client_entry: Create new c
WAP1#lient 74de.2b81.56c4 for application 0x1
Jan 29 11:53:14.620: dot11_auth_initialize_client: 74de.2b81.56c4 is added to the client list for application 0x1
Jan 29 11:53:14.620: dot11_auth_add_client_entry: req->auth_type 0
Jan 29 11:53:14.620: dot11_auth_add_client_entry: auth_methods_inprocess: 2
Jan 29 11:53:14.620: dot11_auth_add_client_entry: eap list name: EAP_LOGIN
Jan 29 11:53:14.620: dot11_run_auth_methods: Start auth method EAP or LEAP
Jan 29 11:53:14.620: dot11_auth_dot1x_start: in the dot11
WAP1#_auth_dot1x_start
Jan 29 11:53:14.620: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to 74de.2b81.56c4
Jan 29 11:53:14.620: EAPOL pak dump tx
Jan 29 11:53:14.621: EAPOL Version: 0x1 type: 0x0 length: 0x002B
Jan 29 11:53:14.621: EAP code: 0x1 id: 0x1 length: 0x002B type: 0x1
01808560: 0100002B 0101002B 01006E65 74776F72 ...+...+..networ
01808570: 6B69643D 54455354 2C6E6173 69643D41 kid=TEST,nasid=A
01808580: 50445741 50312C70 6F727469 643D30 WAP1,portid=0
Jan 29 11:53
WAP1#:14.621: dot11_auth_send_msg: sending data to requestor status 1
Jan 29 11:53:14.621: dot11_auth_send_msg: Sending EAPOL to requestor
Jan 29 11:53:14.622: dot11_mgr_disp_callback: Received message from Local Authenticator
Jan 29 11:53:14.622: dot11_mgr_disp_callback: Received DOT11_AAA_EAP from Local Authenticator
Jan 29 11:53:14.622: dot11_mgr_sm_run_machine: Executing Action(BRIDGE,AUTHENTICATOR_REPLY) for 74de.2b81.56c4
Jan 29 11:53:14.622: dot11_mgr_sm_send_response_to_client: Forwarding Authenti
WAP1#cator message to client 74de.2b81.56c4
Jan 29 11:53:14.622: EAPOL pak dump tx
Jan 29 11:53:14.622: EAPOL Version: 0x1 type: 0x0 length: 0x002B
Jan 29 11:53:14.622: EAP code: 0x1 id: 0x1 length: 0x002B type: 0x1
01808690: 0100002B 0101002B ...+...+
018086A0: 01006E65 74776F72 6B69643D 54455354 ..networkid=TEST
018086B0: 2C6E6173 69643D41 50445741 50312C70 ,nasid=WAP1,p
018086C0: 6F727469 643D30 ortid=0
Jan 29 11:53:14.623: dot1x-regi -
Cisco 871w, radius server local, and leap or eap-fast will not authenticate
Hello, i trying to setup eap-fast or leap on my 871w. i belive i have it confiured correctly but i can not get any device to authenticate to router. Below is the confiureation that i being used. any help would be welcome!
! Last configuration change at 15:51:30 AZT Wed Jan 4 2012 by testtest
! NVRAM config last updated at 15:59:37 AZT Wed Jan 4 2012 by testtest
version 12.4
configuration mode exclusive auto
service nagle
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service linenumber
service pt-vty-logging
service sequence-numbers
hostname router871
boot-start-marker
boot-end-marker
logging count
logging message-counter syslog
logging buffered 4096
logging rate-limit 512 except critical
logging console critical
enable secret 5 <omitted>
aaa new-model
aaa group server radius rad-test3
server 192.168.16.49 auth-port 1812 acct-port 1813
aaa authentication login default local
aaa authentication login eap-methods group rad-test3
aaa authorization exec default local
aaa session-id common
clock timezone AZT -7
clock save interval 8
dot11 syslog
dot11 ssid test2
vlan 2
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 <omitted>
dot11 ssid test1
vlan 1
authentication open
authentication key-management wpa
wpa-psk ascii 7 <omitted>
dot11 ssid test3
vlan 3
authentication open eap eap-methods
authentication network-eap eap-methods
no ip source-route
no ip gratuitous-arps
ip options drop
ip dhcp bootp ignore
ip dhcp excluded-address 192.162.16.49 192.162.16.51
ip dhcp excluded-address 192.168.16.33
ip dhcp excluded-address 192.168.16.1 192.168.16.4
ip dhcp pool vlan1pool
import all
network 192.168.16.0 255.255.255.224
default-router 192.168.16.1
domain-name test1.local.home
lease 4
ip dhcp pool vlan2pool
import all
network 192.168.16.32 255.255.255.240
default-router 192.168.16.33
domain-name test2.local.home
lease 0 6
ip dhcp pool vlan3pool
import all
network 192.168.16.48 255.255.255.240
default-router 192.168.16.49
domain-name test3.local.home
lease 2
ip cef
ip inspect alert-off
ip inspect max-incomplete low 25
ip inspect max-incomplete high 50
ip inspect one-minute low 25
ip inspect one-minute high 50
ip inspect udp idle-time 15
ip inspect tcp idle-time 1800
ip inspect tcp finwait-time 30
ip inspect tcp synwait-time 60
ip inspect tcp block-non-session
ip inspect tcp max-incomplete host 25 block-time 2
ip inspect name firewall tcp router-traffic
ip inspect name firewall ntp
ip inspect name firewall ftp
ip inspect name firewall udp router-traffic
ip inspect name firewall pop3
ip inspect name firewall pop3s
ip inspect name firewall imap
ip inspect name firewall imap3
ip inspect name firewall imaps
ip inspect name firewall smtp
ip inspect name firewall ssh
ip inspect name firewall icmp router-traffic timeout 10
ip inspect name firewall dns
ip inspect name firewall h323
ip inspect name firewall hsrp
ip inspect name firewall telnet
ip inspect name firewall tftp
no ip bootp server
no ip domain lookup
ip domain name local.home
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip accounting-threshold 100
ip accounting-list 192.168.16.0 0.0.0.31
ip accounting-list 192.168.16.32 0.0.0.15
ip accounting-list 192.168.16.48 0.0.0.15
ip accounting-transits 25
login block-for 120 attempts 5 within 60
login delay 5
login on-failure log
memory free low-watermark processor 65536
memory free low-watermark IO 16384
username testtest password 7 <omitted>
archive
log config
logging enable
logging size 255
notify syslog contenttype plaintext
hidekeys
path tftp://<omitted>/archive-config
write-memory
ip tcp synwait-time 10
ip ssh time-out 20
ip ssh authentication-retries 2
ip ssh logging events
ip ssh version 2
bridge irb
interface Loopback0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
interface Null0
no ip unreachables
interface FastEthernet0
switchport mode trunk
shutdown
interface FastEthernet1
switchport mode trunk
shutdown
interface FastEthernet2
shutdown
spanning-tree portfast
interface FastEthernet3
spanning-tree portfast
interface FastEthernet4
description Cox Internet Connection
ip address dhcp
ip access-group ingress-filter in
ip access-group egress-filter out
no ip redirects
no ip unreachables
no ip proxy-arp
ip accounting access-violations
ip flow ingress
ip flow egress
ip inspect firewall out
ip nat outside
ip virtual-reassembly
ip tcp adjust-mss 1460
load-interval 30
duplex auto
speed auto
no cdp enable
interface Dot11Radio0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 2 mode ciphers aes-ccm
encryption key 1 size 128bit 7 <omitted> transmit-key
encryption mode wep mandatory
broadcast-key vlan 1 change <omitted> membership-termination
broadcast-key vlan 3 change <omitted> membership-termination
broadcast-key vlan 2 change <omitted> membership-termination
ssid test2
ssid test1
ssid test3
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
rts threshold 2312
no cdp enable
interface Dot11Radio0.1
description <omitted>
encapsulation dot1Q 1 native
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.2
description <omitted>
encapsulation dot1Q 2
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Dot11Radio0.3
description <omitted>
encapsulation dot1Q 3
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface Vlan1
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan2
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 2
bridge-group 2 spanning-disabled
interface Vlan3
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 3
bridge-group 3 spanning-disabled
interface BVI1
description <omitted>
ip address 192.168.16.1 255.255.255.224
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI2
description <omitted>
ip address 192.168.16.33 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI3
description <omitted>
ip address 192.168.16.49 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
no ip http server
no ip http secure-server
ip http secure-ciphersuite 3des-ede-cbc-sha rc4-128-sha
ip http timeout-policy idle 5 life 43200 requests 5
ip flow-top-talkers
top 10
sort-by bytes
ip nat inside source list 1 interface FastEthernet4 overload
ip nat inside source static tcp 192.168.16.50 80 interface FastEthernet4 80
ip nat inside source static tcp 192.168.16.50 53 interface FastEthernet4 53
ip nat inside source static tcp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 88 interface FastEthernet4 88
ip nat inside source static udp 192.168.16.50 53 interface FastEthernet4 53
ip access-list extended egress-filter
deny ip any host <omitted>
deny ip any host <omitted>
deny ip host <omitted> any
deny ip host <omitted> any
remark ----- Bogons Filter -----
deny ip 0.0.0.0 0.255.255.255 any
deny ip 10.0.0.0 0.10.9.255 any
deny ip 10.0.0.0 0.10.13.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip 169.254.0.0 0.0.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
deny ip 192.0.0.0 0.0.0.255 any
deny ip 192.0.2.0 0.0.0.255 any
deny ip 192.168.0.0 0.0.15.255 any
deny ip 192.168.0.0 0.0.255.255 any
deny ip 198.18.0.0 0.1.255.255 any
deny ip 198.51.100.0 0.0.0.255 any
deny ip 203.0.113.0 0.0.0.255 any
deny ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
permit ip <omitted> 0.0.0.3 any
deny ip any any log
ip access-list extended ingress-filter
remark ----- To get IP form COX -----
permit udp any eq bootps any eq bootpc
deny icmp any any log
deny udp any any eq echo
deny udp any eq echo any
deny tcp any any fragments
deny udp any any fragments
deny ip any any fragments
deny ip any any option any-options
deny ip any any ttl lt 4
deny ip any host <omitted>
deny ip any host <omitted>
deny udp any any range 33400 34400
remark ----- Bogons Filter -----
deny ip 0.0.0.0 0.255.255.255 any
deny ip 10.0.0.0 0.255.255.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip 169.254.0.0 0.0.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
deny ip 192.0.0.0 0.0.0.255 any
deny ip 192.0.2.0 0.0.0.255 any
deny ip 192.168.0.0 0.0.255.255 any
deny ip 198.18.0.0 0.1.255.255 any
deny ip 198.51.100.0 0.0.0.255 any
deny ip 203.0.113.0 0.0.0.255 any
deny ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
deny ip 10.10.10.0 0.0.0.255 any
deny ip 10.10.11.0 0.0.0.255 any
deny ip 10.10.12.0 0.0.0.255 any
deny ip any any log
access-list 1 permit 192.168.16.0 0.0.0.63
access-list 20 permit 127.127.1.1
access-list 20 permit 204.235.61.9
access-list 20 permit 173.201.38.85
access-list 20 permit 216.229.4.69
access-list 20 permit 152.2.21.1
access-list 20 permit 130.126.24.24
access-list 21 permit 192.168.16.0 0.0.0.63
radius-server local
no authentication mac
eapfast authority id <omitted>
eapfast authority info <omitted>
eapfast server-key primary 7 <omitted>
nas 192.168.16.49 key 7 <omitted>
group rad-test3
vlan 3
ssid test3
user test nthash 7 <omitted> group rad-test3
user testtest nthash 7 <omitted> group rad-test3
radius-server attribute 32 include-in-access-req format %h
radius-server host 192.168.16.49 auth-port 1812 acct-port 1813 key 7 <omitted>
radius-server vsa send accounting
control-plane host
control-plane transit
control-plane cef-exception
control-plane
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieee
bridge 2 route ip
bridge 3 protocol ieee
bridge 3 route ip
line con 0
password 7 <omitted>
logging synchronous
no modem enable
transport output telnet
line aux 0
password 7 <omitted>
logging synchronous
transport output telnet
line vty 0 4
password 7 <omitted>
logging synchronous
transport preferred ssh
transport input ssh
transport output ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
process cpu threshold type total rising 80 interval 10 falling 40 interval 10
ntp authentication-key 1 md5 <omitted> 7
ntp authenticate
ntp trusted-key 1
ntp source FastEthernet4
ntp access-group peer 20
ntp access-group serve-only 21
ntp master 1
ntp server 152.2.21.1 maxpoll 4
ntp server 204.235.61.9 maxpoll 4
ntp server 130.126.24.24 maxpoll 4
ntp server 216.229.4.69 maxpoll 4
ntp server 173.201.38.85 maxpoll 4
endso this what i am getting now for debug? any thoughs?
010724: Jan 5 16:26:04.527 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/2
010725: Jan 5 16:26:08.976 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/2
010726: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010727: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010728: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010729: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010730: Jan 5 16:26:08.976 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010731: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010732: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010733: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010734: Jan 5 16:26:08.976 AZT: EAPOL pak dump tx
010735: Jan 5 16:26:08.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010736: Jan 5 16:26:08.976 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0AD05650: 01000004 04010004 ........
0AD05660:
010737: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 1
010738: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010739: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010740: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010741: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 0
010742: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
010743: Jan 5 16:26:08.980 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010744: Jan 5 16:26:08.984 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010745: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010746: Jan 5 16:26:09.624 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010747: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: req->auth_type 0
010748: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010749: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010750: Jan 5 16:26:09.624 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010751: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010752: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010753: Jan 5 16:26:09.624 AZT: EAPOL pak dump tx
010754: Jan 5 16:26:09.624 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010755: Jan 5 16:26:09.624 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50: 01000031 01010031 ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30 r871,portid=0
010756: Jan 5 16:26:09.644 AZT: dot11_auth_send_msg: sending data to requestor status 1
010757: Jan 5 16:26:09.648 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010758: Jan 5 16:26:09.648 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010759: Jan 5 16:26:09.656 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010760: Jan 5 16:26:09.656 AZT: EAPOL pak dump rx
010761: Jan 5 16:26:09.656 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010762: Jan 5 16:26:09.656 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0B060D50: 01000009 02010009 ........
0B060D60: 01746573 74 .test
010763: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010764: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010765: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010766: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198):Orig. component type = DOT11
010767: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: ssid [282] 8
010768: Jan 5 16:26:09.664 AZT: RADIUS: 74 6F 79 73 6F 6E [toyson]
010769: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: interface [175] 3
010770: Jan 5 16:26:09.664 AZT: RADIUS: 36 [6]
010771: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010772: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198): acct_session_id: 408
010773: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010774: Jan 5 16:26:09.664 AZT: RADIUS(00000198): sending
010775: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Send Access-Request to 162.168.16.49:1645 id 1645/3, len 133
010776: Jan 5 16:26:09.664 AZT: RADIUS: authenticator BF 69 DD DF 89 1F C6 FB - EF EC 12 EB C5 3F 3A CD
010777: Jan 5 16:26:09.664 AZT: RADIUS: User-Name [1] 6 "test"
010778: Jan 5 16:26:09.664 AZT: RADIUS: Framed-MTU [12] 6 1400
010779: Jan 5 16:26:09.664 AZT: RADIUS: Called-Station-Id [30] 16 "0019.3075.e660"
010780: Jan 5 16:26:09.664 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010781: Jan 5 16:26:09.668 AZT: RADIUS: Service-Type [6] 6 Login [1]
010782: Jan 5 16:26:09.668 AZT: RADIUS: Message-Authenticato[80] 18
010783: Jan 5 16:26:09.668 AZT: RADIUS: 5B FA 47 07 0E E3 4B 71 7F 60 6E 4E 91 37 84 A6 [[?G???Kq?`nN?7??]
010784: Jan 5 16:26:09.668 AZT: RADIUS: EAP-Message [79] 11
010785: Jan 5 16:26:09.668 AZT: RADIUS: 02 01 00 09 01 74 65 73 74 [?????test]
010786: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
010787: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port [5] 6 661
010788: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Id [87] 5 "661"
010789: Jan 5 16:26:09.668 AZT: RADIUS: NAS-IP-Address [4] 6 192.168.16.49
010790: Jan 5 16:26:09.668 AZT: RADIUS: Nas-Identifier [32] 11 "router871"
010791: Jan 5 16:26:14.501 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010792: Jan 5 16:26:19.018 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010793: Jan 5 16:26:23.739 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010794: Jan 5 16:26:28.700 AZT: RADIUS: Fail-over to (162.168.16.49:1812,1813) for id 1645/3
router871#
010795: Jan 5 16:26:33.629 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010796: Jan 5 16:26:38.494 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010797: Jan 5 16:26:39.794 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010798: Jan 5 16:26:39.794 AZT: EAPOL pak dump rx
010799: Jan 5 16:26:39.794 AZT: EAPOL Version: 0x1 type: 0x1 length: 0x0000
0AD053D0: 01010000 ....
010800: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,EAP_START) for d8b3.7759.0488
010801: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_ignore_event: Ignore event: do nothing
router871#
010802: Jan 5 16:26:43.007 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010803: Jan 5 16:26:47.336 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/3
010804: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010805: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010806: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010807: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010808: Jan 5 16:26:47.336 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010809: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010810: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010811: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010812: Jan 5 16:26:47.336 AZT: EAPOL pak dump tx
010813: Jan 5 16:26:47.336 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010814: Jan 5 16:26:47.336 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0B060710: 01000004 04010004 ........
0B060720:
010815: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 1
010816: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010817: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010818: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010819: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 0
010820: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
router871#
010821: Jan 5 16:26:47.340 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010822: Jan 5 16:26:47.344 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010823: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010824: Jan 5 16:26:47.972 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010825: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: req->auth_type 0
010826: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010827: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010828: Jan 5 16:26:47.976 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010829: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010830: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010831: Jan 5 16:26:47.976 AZT: EAPOL pak dump tx
010832: Jan 5 16:26:47.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010833: Jan 5 16:26:47.976 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50: 01000031 01010031 ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30 r871,portid=0
010834: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: sending data to requestor status 1
010835: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010836: Jan 5 16:26:47.996 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010837: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010838: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
router871#
010839: Jan 5 16:26:47.996 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
router871#
010840: Jan 5 16:26:58.634 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010841: Jan 5 16:26:58.634 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010842: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: req->auth_type 0
010843: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010844: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010845: Jan 5 16:26:58.638 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010846: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010847: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010848: Jan 5 16:26:58.638 AZT: EAPOL pak dump tx
010849: Jan 5 16:26:58.638 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010850: Jan 5 16:26:58.638 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060710: 01000031 01010031 ...1...1
0B060720: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060730: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B060740: 72383731 2C706F72 7469643D 30 r871,portid=0
010851: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: sending data to requestor status 1
010852: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010853: Jan 5 16:26:58.658 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010854: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010855: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
010856: Jan 5 16:27:01.603 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010857: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list ingress-filter denied tcp 32.42.41.254(57443) -> 72.201.117.84(59652), 1 packet
010858: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list egress-filter denied tcp 22.3.184.118(0) -> 74.125.53.188(0), 4 packets
010859: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010860: Jan 5 16:27:12.261 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010861: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: req->auth_type 0
010862: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010863: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010864: Jan 5 16:27:12.261 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010865: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010866: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010867: Jan 5 16:27:12.261 AZT: EAPOL pak dump tx
010868: Jan 5 16:27:12.261 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010869: Jan 5 16:27:12.261 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060FD0: 01000031 01010031 ...1...1
0B060FE0: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060FF0: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B061000: 72383731 2C706F72 7469643D 30 r871,portid=0
010870: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: sending data to requestor status 1
010871: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010872: Jan 5 16:27:12.285 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010873: Jan 5 16:27:12.293 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010874: Jan 5 16:27:12.293 AZT: EAPOL pak dump rx
010875: Jan 5 16:27:12.293 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010876: Jan 5 16:27:12.293 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0AD05290: 01000009 02010009 ........
0AD052A0: 01746573 74 .test
010877: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010878: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010879: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010880: Jan 5 16:27:12.301 AZT: RADIUS/ENCODE(0000019B):Orig. component type = DOT11
010881: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: ssid [282] 8
010882: Jan 5 16:27:12.305 AZT: RADIUS: 74 6F 79 73 6F 6E [toyson]
010883: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: interface [175] 3
010884: Jan 5 16:27:12.305 AZT: RADIUS: 36 [6]
010885: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010886: Jan 5 16:27:12.305 AZT: RADIUS/ENCODE(0000019B): acct_session_id: 411
010887: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010888: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): sending
010889: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Send Access-Request to 162.168.16.49:1645 id 1645/4, len 133
010890: Jan 5 16:27:12.305 AZT: RADIUS: authenticator 6F 6C 63 31 88 DE 30 A2 - C2 06 12 EB 50 A3 53 36
010891: Jan 5 16:27:12.305 AZT: RADIUS: User-Name [1] 6 "test"
010892: Jan 5 16:27:12.305 AZT: RADIUS: Framed-MTU [12] 6 1400
010893: Jan 5 16:27:12.305 AZT: RADIUS: Called-Station-Id [30] 16 "0019.3075.e660"
010894: Jan 5 16:27:12.305 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010895: Jan 5 16:27:12.305 AZT: RADIUS: Service-Type [6] 6 Login [1]
010896: Jan 5 16:27:12.305 AZT: RADIUS: Message-Authenticato[80] 18
010897: Jan 5 16:27:12.305 AZT: RADIUS: 9D D5 62 1A 38 13 94 30 3A 43 D7 A4 AE A4 43 64 [??b?8??0:C????Cd]
010898: Jan 5 16:27:12.305 AZT: RADIUS: EAP-Message [79] 11
010899: Jan 5 16:27:12.305 AZT: RADIUS: 02 01 00 09 01 74 65 73 74 [?????test]
010900: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
010901: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port [5] 6 664
010902: Jan 5 16:27:12.309 AZT: RADIUS: NAS-Port-Id [87] 5 "664"
010903: Jan 5 16:27:12.309 AZT: RADIUS: NAS-IP-Address [4] 6 192.168.16.49
010904: Jan 5 16:27:12.309 AZT: RADIUS: Nas-Identifier [32] 11 "router871"
010905: Jan 5 16:27:16.642 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/4 -
Client Exclusion Policies on WLC not working with ISE as RADIUS Server
Hi,
for our Guest WLAN (Security Setting for this SSID:Layer2: MAC filtering, Layer3:none) we use ISE as RADIUS Server. On WLC I enabled client exclusion polices and checked all options (Excessive 802.11 Auth. Failures etc..).. But even if a client fails 20times at authentication, it is not excluded on the wlc. It works with other SSIDs, where security settings are set to 802.1x.
Am I missing any settings here or do you have some tipps on how to troubleshoot this?
Thanks very much!Hi Renata,
If those guest failures are not associated with valid guest users (i.e. people who have forgotten their account or entering the wrong password) there isn't anything that can be done. The main point of Guest WLAN is to make it as easy as possible for Guests - individuals with device configurations you don't want to deal with or know about, to connect your network for internet access. From a WiFi/802.11 perspective, the standard Guest WLAN setup means its easy for any device to connect.
If your Guest WLAN has the following:
SSID is broadcast enabled, Security = OPEN, Encryption = none, then any 802.11 device can find the WLAN via passive scanning and connect. And any device that connects will get the ISE portal. Once recieveing that portal they can guess away at valid username/password.
I would suspect that unless your Guest WiFi is adjacent to a Mall, school, hotel or other hi-density area of individuals with time and electronics on their hands, other than alerts in your ops window and logs, resources associated with this (WLC & ISE) are very low.
You can try and dull the noise a few ways.
Option 1. create and ISE log filter on those alerts so they don't cluter the console.
Option 2. Stop broadcasting the SSID. This is not a security measure, but will cut volume of people connecting to the SSID significantly. You will have to tell your guests what SSID or include it in their credential communication.
Option 3. Put a very simple PSK on the SSID. The PSK will become a public secret - shared with valid guests, doesn't have change as it's purpose is not security. You will have to include this information on their credential communication.
Option 4 - both 2 and 3
The most effective option would be 3.
Good Luck! -
Web authentication with Radius server problem
Hello,
I'm having problem to web authenticate users via radius server for one WLC. Here is the outpu from WLC:
*emWeb: Mar 26 14:17:31.537: 20:7d:xx:xx:d8:f0 Username entry (aaaaaa) created for mobile, length = 7
*emWeb: Mar 26 14:17:31.537: 20:7d:xx:xx:d8:f0 Username entry (aaaaaa) created in mscb for mobile, length = 7
*aaaQueueReader: Mar 26 14:17:31.537: Unable to find requested user entry for aaaaaa
*aaaQueueReader: Mar 26 14:17:31.537: ReProcessAuthentication previous proto 8, next proto 1
*aaaQueueReader: Mar 26 14:17:31.537: AuthenticationRequest: 0x1e08eb94
*aaaQueueReader: Mar 26 14:17:31.538: Callback.....................................0x10908d90
*aaaQueueReader: Mar 26 14:17:31.538: protocolType.................................0x00000001
*aaaQueueReader: Mar 26 14:17:31.538: proxyState...................................20:7D:xx:xx:D8:F0-00:00
*aaaQueueReader: Mar 26 14:17:31.538: Packet contains 11 AVPs (not shown)
*aaaQueueReader: Mar 26 14:17:31.538: apfVapRadiusInfoGet: WLAN(1) dynamic int attributes srcAddr:0x0, gw:0x0, mask:0x0, vlan:0, dpPort:0, srcPort:0
*aaaQueueReader: Mar 26 14:17:31.538: 20:7d:xx:xx:d8:f0 Successful transmission of Authentication Packet (id 67) to 10.xx.33.249:1645, proxy state 20:7d:xx:xx:d8:f0-00:01
*aaaQueueReader: Mar 26 14:17:31.538: 00000000: 01 43 00 8c 48 7c a7 ff df 06 53 30 c0 be e1 8e .C..H|....S0....
*aaaQueueReader: Mar 26 14:17:31.538: 00000010: d7 fd 8b d3 01 09 73 65 66 72 73 76 65 02 12 7b ......aaaaaa..{
*aaaQueueReader: Mar 26 14:17:31.538: 00000020: ae 2e f5 eb fa cf f5 cc 3b 08 65 d7 04 0e ba 06 ........;.e.....
*aaaQueueReader: Mar 26 14:17:31.538: 00000030: 06 00 00 00 01 04 06 0a 2e 09 14 05 06 00 00 00 ................
*aaaQueueReader: Mar 26 14:17:31.538: 00000040: 0d 20 0d 73 65 76 73 74 2d 6c 77 63 31 30 3d 06 ...xxxxx-lwc10=.
*aaaQueueReader: Mar 26 14:17:31.538: 00000050: 00 00 00 13 1a 0c 00 00 37 63 01 06 00 00 00 01 ........7c......
*aaaQueueReader: Mar 26 14:17:31.538: 00000060: 1f 0e 31 39 32 2e 31 36 38 2e 31 2e 36 31 1e 0c ..192.168.1.61..
*aaaQueueReader: Mar 26 14:17:31.538: 00000070: 31 30 2e 34 36 2e 39 2e 32 30 50 12 95 11 7c d9 10.xx.9.20P...|.
*aaaQueueReader: Mar 26 14:17:31.538: 00000080: 75 8e 01 6e bf 62 38 f8 38 ab 68 4a u..n.b8.8.hJ
*radiusTransportThread: Mar 26 14:17:31.603: 00000000: 03 43 00 14 e5 8c e7 75 52 04 af e0 07 b7 fb 96 .C.....uR.......
*radiusTransportThread: Mar 26 14:17:31.603: 00000010: c1 4a fb 40 .J.@
*radiusTransportThread: Mar 26 14:17:31.603: ****Enter processIncomingMessages: response code=3
*radiusTransportThread: Mar 26 14:17:31.603: ****Enter processRadiusResponse: response code=3
*radiusTransportThread: Mar 26 14:17:31.603: 20:7d:xx:xx:d8:f0 Access-Reject received from RADIUS server 10.xx.33.249 for mobile 20:7d:xx:xx:d8:f0 receiveId = 0
*radiusTransportThread: Mar 26 14:17:31.603: ReProcessAuthentication previous proto 1, next proto 2
*radiusTransportThread: Mar 26 14:17:31.603: AuthenticationRequest: 0x1da9fa4c
*radiusTransportThread: Mar 26 14:17:31.603: Callback.....................................0x10908d90
*radiusTransportThread: Mar 26 14:17:31.603: protocolType.................................0x00000002
*radiusTransportThread: Mar 26 14:17:31.603: proxyState...................................20:7D:xx:xx:D8:F0-00:00
*radiusTransportThread: Mar 26 14:17:31.603: Packet contains 11 AVPs (not shown)
*radiusTransportThread: Mar 26 14:17:31.605: 20:7d:xx:xx:d8:f0 Returning AAA Error 'No Server' (-7) for mobile 20:7d:xx:xx:d8:f0
*radiusTransportThread: Mar 26 14:17:31.605: AuthorizationResponse: 0x2dd03648
*radiusTransportThread: Mar 26 14:17:31.605: structureSize................................32
*radiusTransportThread: Mar 26 14:17:31.605: resultCode...................................-7
*radiusTransportThread: Mar 26 14:17:31.605: protocolUsed.................................0x00000002
*radiusTransportThread: Mar 26 14:17:31.605: proxyState...................................20:7D:xx:xx:D8:F0-00:00
*radiusTransportThread: Mar 26 14:17:31.605: Packet contains 0 AVPs:
*emWeb: Mar 26 14:17:31.605: Authentication failed for aaaaaa
*emWeb: Mar 26 14:17:31.605: 20:7d:xx:xx:d8:f0 Username entry deleted for mobile
*emWeb: Mar 26 14:17:31.605: 20:7d:xx:xx:d8:f0 Plumbing web-auth redirect rule due to user logout
*emWeb: Mar 26 14:17:31.605: 20:7d:xx:xx:d8:f0 192.168.1.61 WEBAUTH_REQD (8) Deleting mobile policy rule 42461
*emWeb: Mar 26 14:17:31.605: 20:7d:xx:xx:d8:f0 Adding Web RuleID 42464 for mobile 20:7d:xx:xx:d8:f0
*emWeb: Mar 26 14:17:31.605: 20:7d:xx:xx:d8:f0 Web Authentication failure for station
*emWeb: Mar 26 14:17:31.605: 20:7d:xx:xx:d8:f0 192.168.1.61 WEBAUTH_REQD (8) Reached ERROR: from line 5069
That was pretty clear for me that Radius is refusing to give user access.
Fully-Qualified-User-Name = NMEA\aaaaaa
NAS-IP-Address = 10.xx.9.20
NAS-Identifier = xxxxx-lwc10
Called-Station-Identifier = 10.xx.9.20
Calling-Station-Identifier = 192.168.1.61
Client-Friendly-Name = YYY10.xx
Client-IP-Address = 10.xx.9.20
NAS-Port-Type = Wireless - IEEE 802.11
NAS-Port = 13
Proxy-Policy-Name = Use Windows authentication forall users
Authentication-Provider = Windows
Authentication-Server = <undetermined>
Policy-Name = YYYYY Wireless Users
Authentication-Type = PAP
EAP-Type = <undetermined>
Reason-Code = 66
Reason = The user attempted to use an authentication method that is not enabled on the matching remote access policy
That output is from WLC 5508 version 7.0.235
What is strange, that user was able to authenticate from other before refresh WLC 4402 ver 4.2.207. I cannot change WLC because of AP which cannot run old version.
this is output from working client connection from old WLC
NAS-IP-Address = 10.xx.9.13
NAS-Identifier = xxxxx-lwc03
Client-Friendly-Name = YYY10.46
Client-IP-Address = 10.xx.9.13
Calling-Station-Identifier = 192.168.19.246
NAS-Port-Type = <not present>
NAS-Port = <not present>
Proxy-Policy-Name = Use Windows authentication for all users
Authentication-Provider = Windows
Authentication-Server = <undetermined>
Policy-Name = YYYYY Wireless Guest Access
Authentication-Type = PAP
EAP-Type = <undetermined>
I know there is different Policy Name used, but my question is why it is not using the same as on old WLC when configuration is same.
Is there any way I can force users to use different policy from WLC or AP configuration or is this solely configuration of Radius?
Is it maybe problem of version 7.0.235?
Any toughts would be much appriciated.Scott,
You are probably right. The condition that is checked for the first policy name (we have 2) is to match
NAS-Port-Type = Wireless - IEEE 802.11, and this is basically used to differentiate guests from other company users.
as you can see from the logs the one that is working correctly is not sending NAS-Port-Type. The question is why.
As I said before.
WLC 5508 ver. 7.0.235 is sending NAS-Port-Type
WLC 4402 ver. 4.2.207 is not.
The same user was working OK on 4402 WLC and after refresh and associating APs to 5508 it all broke, so client did not changed anything on adapter. -
VPN Tunnel w/ 802.1X port authentication against remote RADIUS server
I have a Cisco 892 setup as a VPN client connecting to an ASA 5515-X. The tunnel works fine and comes up if theirs correct traffic. I have two RADIUS servers I want to use certificate based authentication to, that are located behind the ASA 5515-X.
If I connect a computer that has the correct certificates to ports FA0 through 3, authentication won't work. I'll see the following. This happens even if the VPN tunnel is established already by doing something such as connecting a VOIP phone. No entrys are located in the RADIUS logs, and I also cannot ping the RADIUS servers from VLAN10.
*Jan 30 19:46:01.435: %RADIUS-4-RADIUS_DEAD: RADIUS server 192.168.1.100:1812,1813 is not responding.
*Jan 30 19:46:01.435: %RADIUS-4-RADIUS_ALIVE: RADIUS server 192.168.1.100:1812,1813 is being marked alive.
*Jan 30 19:46:21.659: %RADIUS-4-RADIUS_DEAD: RADIUS server 192.168.26.10:1812,1813 is not responding.
*Jan 30 19:46:21.659: %RADIUS-4-RADIUS_ALIVE: RADIUS server 192.168.26.10:1812,1813 is being marked alive.
If I connect a second PC to an interface with 802.1X disabled, such as FA6, the VPN tunnel will establish itself correctly. In this situation, I can ping the RADIUS servers from VLAN10. If I go ahead and connect another PC with correct certificates to a port with 802.1X enabled such as port FA0 through 3, then 802.1X will suceed.
Current configuration : 6199 bytes
! Last configuration change at 15:40:11 EST Mon Feb 3 2014 by
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router1
boot-start-marker
boot-end-marker
aaa new-model
aaa local authentication default authorization default
aaa authentication login default local
aaa authentication dot1x default group radius
aaa authorization network default group radius
aaa session-id common
clock timezone EST -5 0
clock summer-time EDT recurring
ip cef
ip dhcp pool pool
import all
network 192.168.28.0 255.255.255.248
bootfile PXEboot.com
default-router 192.168.28.1
dns-server 192.168.26.10 192.168.1.100 8.8.8.8 4.2.2.2
domain-name domain.local
option 66 ip 192.168.23.10
option 67 ascii PXEboot.com
option 150 ip 192.168.23.10
lease 0 2
ip dhcp pool phonepool
network 192.168.28.128 255.255.255.248
default-router 192.168.28.129
dns-server 192.168.26.10 192.168.1.100
option 150 ip 192.168.1.132
domain-name domain.local
lease 0 2
ip dhcp pool guestpool
network 10.254.0.0 255.255.255.0
dns-server 8.8.8.8 4.2.2.2
domain-name local
default-router 10.254.0.1
lease 0 2
no ip domain lookup
ip domain name remote.domain.local
no ipv6 cef
multilink bundle-name authenticated
license udi pid CISCO892-K9
dot1x system-auth-control
username somebody privilege 15 password 0 password
redundancy
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 5
crypto isakmp key secretpassword address 123.123.123.123
crypto ipsec transform-set pix-set esp-aes 256 esp-sha-hmac
mode tunnel
crypto map pix 10 ipsec-isakmp
set peer 123.123.123.123
set transform-set pix-set
match address 110
interface BRI0
no ip address
encapsulation hdlc
shutdown
isdn termination multidrop
interface FastEthernet0
switchport access vlan 10
switchport voice vlan 11
no ip address
authentication port-control auto
dot1x pae authenticator
spanning-tree portfast
interface FastEthernet1
switchport access vlan 10
switchport voice vlan 11
no ip address
authentication port-control auto
dot1x pae authenticator
spanning-tree portfast
interface FastEthernet2
switchport access vlan 10
switchport voice vlan 11
no ip address
authentication port-control auto
dot1x pae authenticator
spanning-tree portfast
interface FastEthernet3
switchport access vlan 10
switchport voice vlan 11
no ip address
authentication port-control auto
dot1x pae authenticator
spanning-tree portfast
interface FastEthernet4
switchport access vlan 10
switchport voice vlan 11
no ip address
spanning-tree portfast
interface FastEthernet5
switchport access vlan 12
switchport voice vlan 11
no ip address
spanning-tree portfast
interface FastEthernet6
switchport access vlan 10
switchport voice vlan 11
no ip address
spanning-tree portfast
interface FastEthernet7
switchport access vlan 10
switchport voice vlan 11
no ip address
authentication port-control auto
dot1x pae authenticator
spanning-tree portfast
interface FastEthernet8
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0
ip address dhcp
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map pix
interface Vlan1
no ip address
interface Vlan10
ip address 192.168.28.1 255.255.255.248
ip nat inside
ip virtual-reassembly in
interface Vlan11
ip address 192.168.28.129 255.255.255.248
interface Vlan12
ip address 10.254.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 101 interface GigabitEthernet0 overload
ip route 0.0.0.0 0.0.0.0 dhcp
ip radius source-interface Vlan10
ip sla auto discovery
access-list 101 deny ip 192.168.28.0 0.0.0.255 192.168.0.0 0.0.255.255
access-list 101 permit ip 192.168.28.0 0.0.0.255 any
access-list 101 permit ip 10.254.0.0 0.0.0.255 any
access-list 110 permit ip 192.168.28.0 0.0.0.255 192.168.0.0 0.0.255.255
access-list 110 permit ip 192.168.29.0 0.0.0.255 192.168.0.0 0.0.255.255
radius-server host 192.168.1.100 auth-port 1812 acct-port 1813 key secretkey
radius-server host 192.168.26.10 auth-port 1812 acct-port 1813 key secretkey
control-plane
mgcp profile default
line con 0
line aux 0
line vty 0 4
transport input all
ntp source FastEthernet0
ntp server 192.168.26.10
ntp server 192.168.1.100
endI have 802.1X certificate authentication enabled on the computers. As described in my post above, authentication will work if theirs another device on the same VLAN that is connected to a port that bypasses authentication. It seems like I have a chicken and egg scenario, a device needs to be sucessfully connected to VLAN10 before the router will use it's VLAN10 interface to communicate with my remote RADIUS server.
-
802.1x authetication with dynamic Vlan assignment by a radius server
Hi
At school I want to start using 802.1x authentication with dynamic Vlan assignment by a Windows Server 2012R2 Radius server.
When a student logs in, I want it to be placed in the "Students" Vlan, when a Administrative employee logs in, I want it to be placed in the "Administative" vlan and when the client is unknown I want to place it in the "Guest" Vlan.
I have several SG200 switches and I configured everything as mentioned in the administrative guide but I cannot get it to work as desired.
What does work:
- If the client is permitted, the switch changes to "authorized" state. (before anyone logs on to the domain with that client)
- When a User logs on that is part of the Administrative employees, the switch changes to "authorized" and when a student logs on, it changes to "unauthorized".
So far so good.
But what doesn't work:
- it does not put the administrative employee in the Vlan "Administrative", it just enables the port on the switch but leaves it in the default vlan 1.
- I can not find the Guest VLAN.
Any help would be appriciated.Hi Wouter,
Can you see in the packet capture Radius accept message VLAN attribute? Also please ensure you have the latest firmware and boot code:
http://www.cisco.com/c/en/us/support/switches/sg200-26-26-port-gigabit-smart-switch/model.html#~rdtab1
I would recommend you to open ticket with Small Business team so they can go with you through packet capture and configuration steps:
http://www.cisco.com/c/en/us/support/web/tsd-cisco-small-business-support-center-contacts.html
Regards,
Aleksandra -
Setting up Radius server on Autonomous1200 series AP
We have two Autonomous AP's (1220B) that we want to communicate with our RADIUS server using Open Authentication with EAP. When this is set to Open Authentication without additions, I can connect to the network, however when it is set to use EAP, and try to reconnect to the network, an error message is displayed saying "Failed to authenticate." The IP Address of the RADIUS server and the shared secret are the same. Can anybody explain why this is please?
I've got a SonicWall configured for L2TP over IPSec VPN. However, I'm not able to login to it using a Windows domain account only local SonicWall users accounts I've created. I get Error 691: (wrong password or authentication protocol not permitted) - I know the password is correct.
I setup the RADIUS Network Policies on the Windows 2012 Server. However I'm not sure what I need to change on the SonicWall. We also have Global VPN clients connecting to the VPN with IKEv2 so I don't want to prevent them from continuing to use the Global VPN client or have to make any changes on those pre-existing clients. We just want the ability for people to also login to the VPN with the native Windows VPN client too via L2TP over IPSec.
This topic first appeared in the Spiceworks Community -
WLC Radius Server Load Balance
Hi,
Can someone provide me detailed description on how WLC Radius Server Load balance works.
Becuase, I encounted a problem of User Authenticated with the 1st Radius Server, but Accounting Records are actually on 2nd Server .
Any response will be very appreciated
-AngelaHi Angela,
I pasted below the part of config guide explaining the different modes. In summary :
-Fallback off means : when 1st radius server shows dead , WLC moves to the second. And will only change again when the 2nd is dead too.
-Passive means : whent 1st radius is dead, WLC moves to the second. If there is a new authentication coming in, it will try the 1st radius server again
-Active means : WLC constantly sends radius probes to detect when primary is back up.
config radius fallback-test mode {off | passive | active}
where
•off disables RADIUS server fallback.
•passive causes the controller to revert to a server with a lower priority from the available backup servers without using extraneous probe messages. The controller simply ignores all inactive servers for a time period and retries later when a RADIUS message needs to be sent.
•active causes the controller to revert to a server with a lower priority from the available backup servers by using RADIUS probe messages to proactively determine whether a server that has been marked inactive is back online. The controller simply ignores all inactive servers for all active RADIUS requests. Once the primary server receives a response from the recovered ACS server, the active fallback RADIUS server no longer sends probe messages to the server requesting the active probe authentication. -
Aironet 350 AP's with Funk's Steel Belted Radius Server
I have heard that the Aironet AP's don't play nice with Funk's Steel Belted Radius Server. Has anyone had an experience with these products or anything you have heard about this problem would be good to know. I have a customer that already has Funk's Software and doesn't want to change if he doesn't have to. Thanks David Beaver
I have used FUNK's beta code with LEAP support with no problems. The only issue we had and still do, is that we can't use the RADIUS server to authenticate against an LDAP server. I believe that they are working on that also.
-
Flexconnect Radius Server Overwrite interface Question
Hello All,
Can someone confirm/comment on the following:
In a flexconnect scenario, for site 1, i would like to source the radius requests to a remote radius (at the flexconnect site 1). as i can understand i need to enable the RAdius Server Overwrite interface option. Is that all?
Also, for flexconnect sites X this can also be done per WLAN X configuration.
Is this correct?
ThanksHi pana,
Answers below :
Meaning that, even if i configure the Flexconnect groups with local authentication, then how does the Flexconnect ap reach the local radius?
When you are working with local authentication, the AP will communicate with the local RADIUS Server using the local routing in the branch office without the 802.1X traffic being sending to the WLC......the AP will communicate directly to the local radius server using it IP address and the local routing. (This communication is transparent if you see from the WLC because the WLC will not intermediate the authentication between the client and RADIUS, who will intermediate is the AP. The WLC will receive informations when the AP is in connected mode about the client and the authentication method and etc after the user was authenticated).
Example :
RADIUS SERVER
WLC ----SWITCH L3------ROUTER----(MPLS Link)-----ROUTER---SWITCH L3---AP
The WLC continues managing the Access Point but will not"talk" to the RADIUS Server, who will "talk" to the RADIUS Server is the AP in the branch office using the SWITCH L3 (Asumming that you have the RADIUS in one network and the AP in another network in the same branch office)
Understand now ?
As i can understand, in a local switching/local authentication scenario the Flexconnect ap can only map a WLAN to local VLAN( route-able network on the remote site) that serves for the users-data plane. Then in conjunction with the radius server override option, how can this FlexconnectAP send requests to the local radius? I can only suppose that it will do so using the users locally mapped VLAN/WLAN but i cant reference this anywhere.
The AP will only send the requests do the local radius only if you configure the FlexConnect Local Auth and FlexConnect Group. Enabling this option the AP will use it IP Address to communicate with RADIUS without the WLC intermedianting this communication.
Without the FlexConnect Local Auth enable in the WLAN the AP will continue directing the 802.1X requests to the WLC and the WLC will send to the RADIUS Server and in this situation if you enabled the radius overwrite interface the WLC will try to reach the RADIUS Server using the WLAN interface and not the management the interface. (You do not need the radius overwrite interface option to work with Local Auth if you want to use the AP as a Authenticatior, you only use this interface if you want that the WLC with central authentication direct the 802.1X authentications to the RADIUS)
One information about the VLAN/WLAN is really mapped statically but you can manipulate it using the RADIUS Atrributes, changing the VLANs from the USERs based in the AD Group and after the authentication. It can work in local auth scenario or central auth scenario.
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob73dg/emob73/ch7_HREA.html#pgfId-1103070
I hope it helps and if not helps i think i am not understanding the real question. -
Wrv200 and radius server does not work
I am "upgrading" from a dlink di-524 to a wrv200 because I want multiple ssid's. I have my old ssid configured to use the same radius server, port, password, etc. on the wrv200 as on the dlink. When I try to connect it does not authenticate. (Using certificates - wpa2 Enterprise.) The dlink will still authenticate if I plug that back in. The wrv200 seems to be getting to the radius server since it will complain if I change the ip address of the wrv200 to something unexpected. However, the authentication never finishes. It's as if something just does not pass through the router or is dropped. There are no messages on the radius server, not even a rejected or successful message. Does anyone have any ideas on this? I'd hate to have to use 2 routers to add an ssid (I already have 3 in my network.)
Message Edited by Howlie on 12-11-2007 06:48 PMSorry to take so long to reply. I'm using freeradius under Fedora 7. Thanks for the url but I already saw that when I was setting up the radius server. I chatted with tech support about the issue and, since I'm using a wrvs4400n with the same radius settings and working, it is probably a firmware issue. I guess I'll have to just wait for the firmware to catch up.
Message Edited by Howlie on 12-15-2007 03:44 AM
Maybe you are looking for
-
I am having the hardest time getting my new Airport Extreme to work properly. Or at least me to work properly with it. It was working initially then I configured it the way I like it and started having issues. I reset it to default settings and my co
-
[Request] UEFI/GOP Update for 760-2GD5/OC
912-V284-087 N760-2GD5/OC Serial #: 602-V284-45SB1306063243 Current BIOS version: 80.04.BF.00.0A - **http://rghost.net/53265627** Thanks in advance!
-
Is there any A/B testing setup code in dreamweaver?
I am trying to setup A/B testing. I am not a coder but I know there are solutions in Wordpress. How do you setup A/B testing using php code?
-
How to see ALL purchases? (Not just the most recent 2000)
So I got a new MacBook and I want to sync my iPod 5 to it. The problem with this is that it erases all of your iPod's information. I'm okay with this, I just want to be able to put all my songs back onto it. So I go to the iTunes store, click purchas
-
Unable to click on iphoto icon to access photos for uploading to photo web
I am trying to upload some photos to a photo lab website. My iphoto icon is dim/gray and you can't click on it to open it. Any ideas???