Changing router internet IP address for VPN connectivity

I have a Linksys WRT300N router that I just installed for use with my desktop and laptop in my home office. One of the things I need to do is connect to a VPN, but apparently I'm unable to do that since their address is the same as my router's address. How can I change my router's address so there won't be a conflict with connecting to the VPN? Any help in this would be much appreciated. Thanks in advance... DI

Access setup page of router using the Gateway address....
Under Setup .... change the Local IP address to 10.10.10.1 or 192.168.X.1 .... click save settings......

Similar Messages

Unable to set manual IP address for VPN connection

Recently a VPN connection with a client stopped working. They changed phone companies and changed some of the IP addresses.
After alerting them I could no longer log in, I received the new server address which I can log in with it,
BUT my computer is assigned a dynamic address that is already in use on their network. This causes my computer to *not* be connected to their network, even though I am inside their firewall; therefore I cannot adjust the database files I need to.
I have tried to set the VPN (PPTP) connection TCP/IP address IPv4 manually, using the static address they just gave me. But each time I connect, [I believe] their router assigns me an address that is already in use.
They do not use IPv6.
Can anyone give me direction on how to make the manual IP address *stick*?
The tech person at the site keeps telling me it is a problem with my "Mac, because with Windows.... blah, blah, blah".
I am pretty sure this is not the case and in fact I was the one who let her know I was receiving a duplicate address.
Your VPN expertise is really appreciated.
Thanks in advance,
Michele

Hi,
Please make sure the Ad hoc connection IP adress is at the same range with your local connection. In addition, how about recreate the ad hoc connection for test, please have a try.
If problem persists, please use Network troubleshooter in Action Center to fix this problem for test.
Roger Lu
TechNet Community Support

Entering Correct info for VPN connection

please suggest the correct configuration for entering information in order for my laptop to connect via VPN to my newly installed Leopard Server software. On my laptop, I have entered the following info on the System Preferences> network tab...
Configuration: Default
Server Address: 76.173.xx.xxx (my public IP address - do I need anything else?)
Account name: XXXXXX (same as the account name in Server)
under Authentication Settings, my password is fine and my shared secret is the same as on the Server.
Am I entering in everything correctly? i am most concerned as to how the server address is supposed to be written. thanks!!

Hi
If Appletalk is enabled server side and you simply enter the IP address afp is assumed as the protocol to be used. If you prefer the extra effort involved in typing afp:// followed by the IP address you can use that as well. If you want to use the smb service rather than afp simply type smb://followed by the IP address. The same thing applies to ftp services. The Finder supports reads only for ftp services.
If you are using VPN services you simply type in the private IP (LAN-side) address of the server rather than the public IP (WAN-side) address. Once a VPN connection has been established, the remote client behaves as if it is on the same LAN.
You can make a connection using the Public WAN address if you enable port forwarding to a single LAN IP address for services you are interested in. For example if you wanted to access your server remotely using afp you configure your router to forward requests for port 548 to the internal IP address of your server. You can use this method for as many services you like as well as how many your router supports. Most commercially available routers support 10-20. Depending on the router you may have to configure an appropriate firewall rule as well. When faced with that it makes more sense to use a single VPN connection.
I may be in danger of teaching granny to suck eggs but for what its worth for VPN connections to work successfully the remote client’s private IP address has to be different from the host site. For example if the remote site is on 192.168.1.x/24 as is the server then you won’t establish a connection. As far as the remote site is concerned its already connected to that network, why look elsewhere? 192.168.1.x/24 to 192.168.2.x/24 or 10.10.10.x/24 to 192.168.0.x/24 should result in successful VPN connections.
For a list or IP addresses reserved for private use:
http://www.iana.org/faqs/abuse-faq.htm#SpecialUseAddresses
Hope this helps, Tony

Trying to set a delay in an Applescript for VPN connection

I need to be able to set some routes upon opening a particular VPN connection so I did some searching and found a really simple Applescript that does the job. Problem is it tries to set the routes before the VPN actually connects so the routes don't go in.
I added in a 10 second delay which does the trick, but I'm thinking there has to be a way to do this that waits until the VPN actually connects before continuing - so if it takes 5 seconds or 10 or whatever, it waits.
The other thing I'm doing that I think is bad is I'm sending a route delete command before sending the add command. Why? Because if I don't and for some reason the route is partially in the table, it doesn't give an error and ends up not routing. Again, probably a better way to do this.
Here is my current script"
-- Connect Work VPN
tell application "System Events"
tell current location of network preferences
set VPNservice to service "Work" -- name of the VPN service
if exists VPNservice then connect VPNservice
end tell
end tell
delay 10
set gateway to "x.x.x.x" -- omitted here for security
do shell script "route delete 192.168.25.0/24 " & gateway with administrator privileges
do shell script "route delete 192.168.20.0/24 " & gateway with administrator privileges
do shell script "route add 192.168.25.0/24 " & gateway with administrator privileges
do shell script "route add 192.168.20.0/24 " & gateway with administrator privileges
Any suggestions??
Thanks.

you might want to try asking in the Applescript forum under OS X technologies.
I don't have any VPN connections so can't test anything but applescript dictionary for system events indicates that configuration property of a service has a boolean property "connected". so just run a loop with, say, 1 second delay until this porperty becomes true. presumably it would be something along the lines
<pre style="
font-family: Monaco, 'Courier New', Courier, monospace;
font-size: 10px;
margin: 0px;
padding: 5px;
border: 1px solid #000000;
width: 720px;
color: #000000;
background-color: #ADD8E6;
overflow: auto;"
title="this text can be pasted into the Script Editor">
tell application "System Events"
tell current location of network preferences
set VPNservice to service "Work" -- name of the VPN service
if exists VPNservice then connect VPNservice
repeat until (connected of current configuration of VPNservice)
delay 1
end repeat
end tell
end tell
set gateway to "x.x.x.x" -- omitted here for security
do shell script "route delete 192.168.25.0/24 " & gateway with administrator privileges
do shell script "route delete 192.168.20.0/24 " & gateway with administrator privileges
do shell script "route add 192.168.25.0/24 " & gateway with administrator privileges
do shell script "route add 192.168.20.0/24 " & gateway with administrator privileges</pre>

I'm living in Iran and I have an ip address for VPN but I'm having problem in setting it up any one knows can anyone tell me what to do? It works perfectly on my laptop

I'm living in Iran and I have an ip address for VPN but I'm having problem in setting it up any one knows can anyone tell me what to do? It works perfectly on my laptop

Try here:
iTunes Store: My credit card's security code or zip code does not match my bank's records
Then try contacting iTunes
Apple - Support - iTunes - Contact Us

Change of Ship to address for a shopping cart

Hi,
could any body inform me that how to change the ship to address for a company code in SRM. We are using SRM 4.0 and classic system.
Thnaks,
Pijush

Hello,
Check information available here:
http://wiki.sdn.sap.com/wiki/pages/viewpage.action?pageId=230261594
Transaction BBPADDRINTC would be used to change the address.
Regards,
Ricardo

SG300 cant change the Link Local address for an IPv6 interface

There seems to be no apparent way to change the Link Local address for an IPv6 interface
If I create more than one interface they all appear to have the same Link Local address

Never mind, I figured it out
By adding a Link Local address to an interface, it overides the existing one on the interface

HT1051 Trying to change Shipping and Delivery address for one in the US, from Canada, and can't do it. State and zip code appears in red but no change in country name. Using French (Canada) iPhoto app.

Trying to change Shipping and Delivery address for one in the US, from Canada, and can't do it. State and zip code appears in red but no change in country name. Using French (Canada) iPhoto app.

Larry's right, You can still use your credit card, you just need to change the "billing address" to the recievers address. It gets billed to your CC and delivered to the US

Internet stops with PPTP VPN connections to ASUS RT-N66U VPN Router

I have a client with a small office network that has a few people working remotely from Windows 7 and 8 PCs. As an inexpensive solution the client opted to use a VPN router (ASUS RT-N66U) that supports PPTP so remote users could access the shared
files and SQL DB server.
The VPN connectivity for one client was working fine and then stopped working altogether so when the VPN connection is established all Internet and VPN access is stopped. This was especially troubling for me since I work remotely and cannot test or debug after
the VPN session has been connected. I checked the error logs and found nothing. Also there had been no new programs installed. And finally, I ran a full system antivirus scan with no issues found.
In case you are facing a similar issue, before trying something remotely that may not work, use the shutdown with reboot command in a COMMAND window and set a timer for something like 3 minutes to reboot in case you get stuck. (e.g. shutdown -r -t 180).
Problem: The two symptoms of the VPN connection failure are:
1) All Internet browsing stops working locally
2) No data can pass through the VPN tunnel
I created a virtual machine on my local network and replicated the client's environment. I experimented with nearly every setting in the VPN dialogue until and came to the final solution.
Solution: For the VPN adapter on the remote machines I configured DNS settings and used the remote as the default gateway.
* VPN adapter Networking IPV4 Properties for:
- DNS server 1: Main Office VPN Router IP Address
- DNS server 2: A public DNS server (Google is 8.8.8.8)
- I also checked the box to "register this connection addresses in DNS"
Note: Perhaps the local router would also have worked and DNS2 but I didn't test it.
I have documented this because after reading and searching among many Technical articles and the Microsoft support website, I was unable to find the solution that I came up with so I hope to help someone else.
Question1: - Can anyone tell me why the connectivity only works when 'use default gateway on remote network' is checked?
- I have disabled this option with some business class VPN routers and the connectivity still worked to the remote network but it does not work to the Asus router.
Question2: From the information provided can I determine where the problem lies?
Is it the:
1) Remote client PC
2) Remote client router
3) Home office VPN router (Asus RT-N66U)
If the true culprit cannot be determined yet, what steps do you recommend so I can isolate the true cause of the failure.
I appreciate any help so that I can be sure my solution is valid and pass along the findings to ASUS if it is their issue.

Thank you for the suggestion. I have successfully connected through the VPN router when the one client was unable to get VPN throughput working.
I looked at the routing tables with and without the VPN connection established. The differences are that:
1) when VPN is NOT active, there is a route from the local NIC IP to the Internet IP address of the local gateway
destination 68.109.82.xx
mask 255.255.255.0
gateway 192.168.0.1
interface 192.168.0.11
metric 21
2) when VPN IS active, the route to the Internet IP address of the local gateway is deleted and a persistent route to the VPN router local network has been added
Persistent route:
destination 192.168.21.0
mask 255.255.255.0
gateway 192.168.0.1
interface 192.168.0.11
metric 1

Zone Base Forewall for VPN connections does not work after IOS upgrade

Hi all,
We use cisco router 2911 as corporate gateway - there is Zone Based Firewall implemented - I upgraded IOS to last version (15.2(2)T1) - originaly version 15.1(4)M1 - to solve issue with Anyconnect connections (bug CSCtx38806) but I found that after upgrade the VPN users are not able to communicate with sources in other zones.
More specific
WebVPN use this virtual template interface
interface Virtual-Template100
description Template for SSLVPN
ip unnumbered GigabitEthernet0/1.100
zone-member security INSIDE
There are other zones VOICE, LAB, ...
In the policy any connection is allowed (used inspection of icmp, tcp and udp) from INSIDE zone to VOICE or LAB zone
After VPN connection I am able to reach resources in INSIDE zone (which is the most important), but not in other zones. Before upgrade it worked.
Once I changed zone in Virtual-Template interface to VOICE, I was able to reach sources in VOICE zone but not in any other. I searched more and found the stateful firewall is not working for connections from VPN as ping is blocked by policy on returning way - it means by policy VOICE->INSIDE, once I allowed communication from "destination" zone to INSIDE zone - the connections started to work, but of cause it is not something I want to setup.
Does anybody has the same experiance?
Regards
Pavel

It seems to me I should add one importatant note - if client is connected directly in INSIDE zone, he can reach resources in other zones without any issue - so the problem is only when the client is connected by VPN - not in ZBF policy setup.
Pavel

Traffic only allowed one-way for VPN connected computers

Hello,
I currently have an ASA 5505. I have set it up as a remote access SSL VPN. My computers can connect to the VPN just fine. They just can't access the internal LAN (192.168.250.0). They can't ping the inside interface of the ASA, or any of the machines. It seems like all traffic is blocked for them. The strange thing is that when someone is connected to the VPN, I can ping that VPN-connect machine from the ASA and other machines inside the LAN. It seems the traffic only allows one way. I have messed with ACL's with no avail. Any suggestions please?
DHCP Pool: 192.168.250.20-50 --> For LAN
VPN Pool: 192.168.250.100 and 192.168.250.101
Outside interface grabs DHCP from modem
Inside interface: 192.168.1.1
Current Running Config:
: Saved
ASA Version 8.2(5)
hostname HardmanASA
enable password ###### encrypted
passwd ####### encrypted
names
interface Ethernet0/0
switchport access vlan 20
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
switchport access vlan 10
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
switchport access vlan 10
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan10
nameif inside
security-level 100
ip address 192.168.250.1 255.255.255.0
interface Vlan20
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
pager lines 24
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool 192.168.250.100-192.168.250.101 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 10 interface
nat (inside) 10 192.168.250.0 255.255.255.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.250.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh 192.168.250.0 255.255.255.0 inside
ssh timeout 5
ssh version 2
console timeout 0
dhcpd dns 8.8.8.8
dhcpd address 192.168.250.20-192.168.250.50 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2
svc image disk0:/anyconnect-linux-2.5.2014-k9.pkg 3
svc enable
tunnel-group-list enable
group-policy DfltGrpPolicy attributes
dns-server value 8.8.8.8
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
tunnel-group AnyConnect type remote-access
tunnel-group AnyConnect general-attributes
address-pool VPN_Pool
tunnel-group AnyConnect webvpn-attributes
group-alias AnyConnect enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:30fadff4b400e42e73e17167828e046f
: end

Hello,
I seem to be having the same kind of issue although I cannot ping from either end.
Ive set up a l2tp/ipsec vpn which I am able to connect to and get ip from my ip pool (radius authentication is working).
I tried running:
access-list NAT_0 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
nat (inside) 0 access-list NAT_0
but i get an error msg saying that the syntax of the nat command is deprecated. Im running ASA version 8.4.
Ive fiddled around abit to find the correct syntax but have been unsuccessfull so far.
Any help would be much appreciated
This is a part of my config:
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network AD1
host 192.168.1.31
description AD/RADIUS
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network vpn_hosts
subnet 192.168.2.0 255.255.255.0
access-list AD_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list split-acl standard permit 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.1.0 255.255.255.0
access-list inside_0_outbound extended permit ip object NETWORK_OBJ_192.168.1.0_24 object vpn_hosts
ip local pool POOL2 192.168.2.2-192.168.2.10 mask 255.255.255.0
nat (inside,outside) source static any any destination static NETWORK_OBJ_192.168.1.0_25 NETWORK_OBJ_192.168.1.0_25 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static NETWORK_OBJ_192.168.1.0_25 NETWORK_OBJ_192.168.1.0_25 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static vpn_hosts vpn_hosts
object network obj_any
nat (inside,outside) dynamic interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 ########## 1
no vpn-addr-assign aaa
no vpn-addr-assign dhcp

Having issues with WRT54GS router acquiring network address after wireless connection.

I've been experiencing problems acquiring a network address after making a wireless connection with the WRT54GS wireless router. I have a Comcast cable modem connected to the internet port of the router and after configuring the SSID and the 64 bit WEP key, I can connect to my router's SSID, but since I can't get an IP address, never connect to the Internet. I've already cloned the laptop's mac address to no avail. Even after configuring a static IP address, subnet mask and default gateway, still cannot connect. I can Ping and Traceroute from the router but not the PC. I can ping localhost and host IP address from the laptop but not the default gateway. Any suggestions would be appreciated. Thanks, SJ

Connect the computer to the router with the Ethernet cable.
Try to access the internet when you connect the computer to the router with the Ethernet cable.
Open the setup page of the router and go to Status page. Check the Internet IP address on the status page of the router.
If you are able to access the Internet with the Wired connection to the router then try to create a new wireless network on your router.
Open the setup page of the router and go to Wireless tab. Change the wireless network name SSID and change the channel to 11. Save the settings. Go to Wireless security sub tab and check the wireless security settings. Click on Wireless MAC filter sub tab and make sure that it is disabled. Click on Advanced wireless settings sub tab. Change the Beacon Interval to 75, RTS and fragmentation threshold to 2304. Save the settings.
Try to connect to the new wireless network and see if that works.
How many wired and wireless computers do you have in the network?

Advice needed for VPN connections

OK to first describe what I'm looking at .We have a bookmobile that goes to 13 different locations within our county. At each stop we are using the service provider's DSL modem to connect to their network, we have two different providers and staff changes the modem at each stop, and a Cisco831 router to make a VPN connection to our PIX. We are using the router to make the VPN connection so that we can have two staff computers use internal network resources i.e. Library database, network drives, e-mail. We tried using Cisco VPN client on the local machine but when we have two clients going on two machines at the same time neither would work. So we let the router make that connection.
We are going to have two bookmobiles operating and I need to purchase another router to make the connection and I am wondering which router would be a better solution for us.
So for me the question is
1) should I keep things as they are and buy a 871 and have staff change modems as needed
2) Should I get an 877, 878 router and make configuration changes daily as needed. Staff have not been able to do this in past. I've enough to do without this!
3) Up for any suggestions Maybe SDM with a pretty GUI for staff to use. It seems Cisco's CLI was too much for them.
Thanks to all for any help
Systems A

No Nat-traversal is enabled.
When we tried multiple VPN connections it was through a DSL modem/router. This is why we went to a Cisco831 router and having it make the secure connection to our PIX.
Thanks for you help

HT201342 In Apple Mail, how do I change the default outgoing address for mailboxes that I've set up?

In Apple Mail (Yosemite on a MacBook Pro), the default address for outgoing messages from mailboxes that I've set up that are *not* tied to separate email accounts has suddenly become my iCloud address (which I almost never use). I've got my default set to use whatever address is the default for the mailbox I'm in. This works fine for mailboxes associated with different mail accounts, and until recently it worked fine for mailboxes that I had set up for convenience, using my default email address (which is an Earthlink address I've had for many years). Somewhere within the last year, perhaps with an upgrade to the OS, I've found that outgoing mail from one of those mailboxes (but not from the general Inbox) defaults to my iCloud address. I have to manually choose a different address each time (which is hard to remember to do). This is new behavior, and very unwelcome. But I can see no way to change the default email address associated with each mailbox.
How do I undo this unwanted connection?

Hi everyone
Sorry however I'm experiencing a similiar issue, in that I have 10 differing email accounts.
However in the default email accounts, for some bizarre reason, only 4 show, being icloud, one of my older yahoo email accounts, my work email and then "From My PC".
I run two other businesses of which I have a proper Google Mail Business Accountsfor each, but non of my google email address show in the default list.
Is there any reason why?
I actually want one of those to show.
I have put my google mail to the top of the inbox, however it still doesn't show?
I've also put the default calendar as my google business account but still the default account doesn't display.
Any ideas?
Jonathan

Best setup for vpn connection

Hi all, Can anyone tell me the normal way of setting up a vpn connection, here we have a router terminating the internet link, and a cisco pix behind it ?

you can try a very simple Easy VPN configuration in this document.
http://www.cisco.com/application/pdf/en/us/guest/products/ps6659/c1650/cdccont_0900aecd80313bdf.pdf
hope this helps.
rate this post.

Changing router internet IP address for VPN connectivity

Similar Messages

Maybe you are looking for