Cisco 7507 connected to a Lucent Stinger

Has anyone had any success connecting a Cisco 7507 AIP to a Lucent Stinger. The Stinger and Cisco are connected back-to-back via a single mode OC3 cable. The AIP on the Cisco shows up/up and the Vpi/Vci circuit on the Stinger also shows that the circuit is up. However I am unable to ping a DSL modem attached to the Stinger.

Here it is....
interface ATM1/0
no ip address
no atm ilmi-keepalive
interface ATM1/0.1 point-to-point
ip address 172.29.41.1 255.255.255.0
pvc 0/40
protocol ip 172.29.41.1 broadcast
protocol ip 172.29.41.2 broadcast
encapsulation aal5snap

Similar Messages

Cisco Webex Connect Jabber 7.2.2 History Missing

Running Cisco Webex Connect 7.2.2 on W7 x64.
Anyone run into chat history missing or only showing 1 day of chat when you know that you shoud have weeks and weeks with certain persons? Default is 9999 days. Had someone ask me to start CWC as administrator and set to some other value, like 9998 days. Worked for a while and resurfaced. Other peers having same issue, so I know it is not specific to my machine. Even got new machine recently with same OS and CWC and problem has surfaced on this new machine too.
I saw that the chat is stored in a db3 file. I do find a couple of those on my machine but not sure if the client is buggy or the file truely is missing the chats. Would need a dBase III browser to find out more.
Is there a more current release of CWC 7.2.2 that might have bug fixes in it that relate to chat history being toast?
Would love to hear from others in here including Cisco support.

Joe,
I normally do not monitor this side of the community, but I am active contributor of the Unified Computing Forum, but somehow I happen to come accross your post, so I wanted to take a minute and ask you if you have tried to open a case directly with the team that support Webex?
http://www.cisco.com/en/US/prod/ps10352/webex_technical_support.html <<< Look for "Sign in to contact support." on the right
I hope that helps.
-Kenny

Cisco Unity Connection 8.6 not getting CLID information from CUCM 8.6

Hello,
Currently Running:
Cisco Unified Communications Manager 8.6.2
Cisco Unity Connection 8.6.2
Problem:
when any outside caller leaves a voicemail, the caller number information is not being sent to unity.
example, I call with my cell phone, 817.555.1234 to my Cisco 7940 phone and it shows the CLID information that i am calling with. iDivert to voice mail, Leave a message. Playback message and just the default message information from Cisco Unity.
we currently upgraded from CUCM 6.1.3 and Unity 5. before i could press 9 and get the caller information.
I have viewed the "Playback Message Settings" and selected "After Playing Each Message, Play" and selected Sender's Information. and also selected "Include Extension and Sender's ANI"
upon playing the VoiceMail after the message i get the default message "From Cisco Unity Connection Messaging System"
I also have the message relaying to my E-mail and I get the same in the subject line.
"Message from Cisco Unity Connection Messaging System (Unknown extension)"
This tends to be a big deal with the Sales team as customers will call and say "Call me back"
But any Internal Calls show the correct information, proper greeting, extension information even on the relay to e-mail.
Any help will be appreciated.
Thanks
Tim

Found another post that referenced Cisco Bug ID CSCti37610.
CUC plays message is from Unity Connection Messaging system
Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
Workaround:
Restart the Unity Connection servers
It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

Failure to upgrade Cisco Unity Connection 8.6.2 to 9.1.2

Hi everybody.
Has someone that can help me with follow problem?
I making a Cisco Unity Connection upgrade from version: 8.6.2.20000-76 to 9.1.2.10000-28. But unfortunately we can't sucessfull to make this process.
On the finish of this process, I can see this outup error:
11/23/2013 12:28:55 upgrade_manager.sh|Cleanup exiting - Cached Data: [Vendor= VMware, Inc.
HWModel=VMware
CPUCount=2
CPUType= Intel(R) Xeon(R) CPU E5-2643 0 @ 3.30GHz
CPUSpeed=3300
MEMSize=6144
BIOSVer=PhoenixTechnologiesLTD 6.00 06/22/2012
ObjectId=1.3.6.1.4.1.9.1.1348
OSVersion=UCOS 5.0.0.0-2
SerialNumber= VMware-56 4d e0 4f 4d 85 87 7b-eb 22 0e 52 a7 73 1a 22
VendorOID=1.3.6.1.4.1.674]|<LVL::Info>
11/23/2013 12:28:55 upgrade_install.sh|Cleaning up download...|<LVL::Info>
11/23/2013 12:28:55 upgrade_install.sh|Cleanup upgrade source area.|<LVL::Info>
11/23/2013 12:28:55 upgrade_install.sh|Ejecting DVD (/dev/sda1)|<LVL::Debug>
11/23/2013 12:28:55 upgrade_install.sh|Removing /common/download/9.1.2.10000-28|<LVL::Info>
11/23/2013 12:28:55 upgrade_install.sh|Started auditd...|<LVL::Info>
11/23/2013 12:28:56 upgrade_install.sh|Started setroubleshoot...|<LVL::Info>
11/23/2013 12:28:56 upgrade_install.sh|Changed selinux mode to enforcing|<LVL::Info>
11/23/2013 12:28:56 upgrade_install.sh|Cleaning up rpm_archive...|<LVL::Info>
11/23/2013 12:28:56 upgrade_install.sh|Removing /common/rpm-archive/9.1.2.10000-28|<LVL::Info>
11/23/2013 12:29:00 upgrade_install.sh|IOWAIT monitor stopped|<LVL::Info>
11/23/2013 12:29:00 upgrade_install.sh|File:/usr/local/bin/base_scripts/upgrade_install.sh:599, Function: main(), Upgrade Failed -- (1)|<LVL::Error>
11/23/2013 12:29:00 upgrade_install.sh|set_upgrade_result: set to 1|<LVL::Debug>
11/23/2013 12:29:00 upgrade_install.sh|is_upgrade_lock_available: Upgrade lock is not available.|<LVL::Debug>
11/23/2013 12:29:00 upgrade_install.sh|is_upgrade_in_progress: Already locked by this process (pid: 14477).|<LVL::Debug>
11/23/2013 12:29:00 upgrade_install.sh|release_upgrade_lock: Releasing lock (pid: 14477)|<LVL::Debug>
Best Regards,
Claudio Costa
A mensagem foi editada por: Claudio Costa

Tks Manish, I just perform a restart on the both nodes on my CUC cluster and after that I did can install this upgrade patch.
Also is very important install the upgrade patch on all servers of the cluster before perform a switch-version on the publisher and then on the others nodes.
Best Regards,
Claudio Costa

Cisco Unity Connection 8.5.1 SU3 to 8.5.1 SU6 & Upgrade to 9.1.2

Two questions !
Firstly - I am upgrading to the latest patch level as I want to upgrade the systems to 9.1.X
I am installing UCSInstall_UCOS_8.5.1.16900-6.sgn.iso onto the inactive partition on the publisher then onto the inactive partition on the subscriber.
Then I plan to switch versions out of hours.
Question - will messages / data that has happened between the installation on the inactive partition and the switch version be preserved ??
So if I install onto the inactive partition at 1pm, then an important message is left at 2pm and I switch version at 3pm, does the iimportant message exist on the active partition at the end ??
Second question -
I have UCCX-8.5.1 SU4 (HA), CUC 8.5.1 SU6 (HA) and CUCM 8.5.1 SU6 (1 pub, 2 sub) - so 7 VM's in total.
If I want to migrate to -
UCSInstall_UCOS_9.1.2.12900-11.sgn.iso & UCSInstall_UCCX_9_0_2_UCOS_9.0.2.11002-27.sgn.iso
in which order should the installations take place ?? CUCM Publisher last ?? Publisher first ??
Thanks
James

Hi James,
+5 to my friend Aman for his good tips here
Messages are preserved during the "switch-version" so the messages left before the command is run will be preserved as they are stored in a "common" partition;
Switching to the Upgraded Version of Connection 8.x Software
If you chose not to automatically switch to the upgraded partition at the end of the upgrade, do the following procedure when you are ready to switch partitions.
To Switch to the Upgraded Version of Connection 8.x Software
Step 1 If you do not have a recent backup, back up the server by using the Disaster Recovery System. For more information, see the Disaster Recovery System Administration Guide for Cisco Unity Connection Release 8.x athttp://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/drs_administration/guide/8xcucdrsag.html.
Step 2 Sign in to Cisco Unified Operating System Administration.
Step 3 From the Settings menu, select Version.
Step 4 On the Version Settings page, select Switch Versions, and the following occurs:
•Connection services are stopped.
•Data from the partition where the older version is installed is copied to the partition where the newer version is installed. If changes to the database schema require updates to the format of data, that occurs in this step. Note that messages are stored in a common partition, so they are not copied.
•The Connection server restarts and switches to the newer version.
Note You can check the status of the installation of the upgrade software by using the CLI command show cuc version. The upgrade is complete when the inactive partition has the upgraded software and the active partition has the old software.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/8x/upgrade/guide/8xcucrugx/8xcucrug009.html#wp1056720
The upgrade order is shown here (above link) as well, which is Pub followed by Sub;
Task List for Upgrading Connection 7.x or 8.x Software to the Shipping 8.x Version in a Connection Cluster
Cheers!
Rob

Cisco Any Connect: Works fine but can't download file

Hello! Here's my question:
I search for documents in a database over a remote vpn using Cisco Any Connect. Works fine. I receive a result, a list of documents that meet my criteria. I can either export to my PC or open. If I try to export, I get a prompt asking where I would like to place the file. I select the place (my desktop) and the window hangs after about 10% on the progress bar. If I try to open the document, a window opens but hangs.
Is there any way to resolve this, is the problem on my end of the remote vpn? Is this an Any Connect issue?
FYI: I am using IE8. I am using a Microsoft Windows Essentials firewall. (I was using Norton before this, same issue.) I have also tried “Display All Websites in Compability View” option in IE but no difference. The tool I am using is Documentum.
Thanks,
Mike

One thing you should do is get rid of that Westell modem from verizon. Its junk. I replaced it with a DLink DSL modem and internet is faster. Not that this suggestion solves your problem.

Issue on Cisco Unity Connection after performing 'utils ntp restart'

Hello everybody.
There's a client with Cisco Unity Connection 8.5.1.10000-206. After doing a 'utils ntp restart', the following message showed up:
Communication is not functioning correctly between the servers in the Cisco Unity Connection cluster. To review server status for the cluster, go to the Tools > Cluster Management page of Cisco Unity Connection Serviceability.
The client states that there was no service for 5 minutes and wants to know if performing this task shoud be disruptive or not and if there is any official document from Cisco stating this.
See SrvConnUnity_1.jpg sent by the client after performing the ntp restart.
Right now the service is normal (see SrvConnUnity_2.jpg attached). The client also sent a 'utils ntp
status':
admin:utils ntp status
ntpd (pid 10899) is running...
     remote           refid      st t when poll reach   delay   offset jitter
==============================================================================
*127.127.1.0     LOCAL(0)        10 l   16   64 377    0.000    0.000   0.002
synchronised to local net at stratum 11
   time correct to within 12 ms
   polling server every 64 s
Current time in UTC is : Fri Apr 26 16:01:23 UTC 2013
Current time in America/Argentina/Buenos_Aires is : Fri Apr 26 13:01:23 ART 2013
admin:
Could anybody help me with this? What steps should I take? Many thanks in advance.
Best,
Patricio

Hello Patricio,
On the command line guide you won't see any downtime requirements for the Unity Connection server:
Command Line Interface Reference Guide for Cisco Unified Communications Solutions Release 8.5(1)
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/cli_ref/8_5_1/cli_ref_851.html
Utils ntp restart
This command restarts the NTP service.
Command syntax
utils ntp restart
Parameters
None
Requirements
Command privilege level: 0
Allowed during upgrade: Yes
Also on the caveats i do not see any particular mention for this: (Caveats could be found applicable to CUC)
Release Notes for Cisco Unified Communications Manager Release 8.5(1)
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/rel_notes/8_5_1/cucm-rel_notes-851.html
Breaking up the output of the "utils ntp status" there are are two considerations:
admin:utils ntp status
ntpd (pid 10899) is running...
     remote           refid      st t when poll reach   delay   offset jitter
==============================================================================
*127.127.1.0     LOCAL(0)        10 l   16   64 377    0.000    0.000   0.002
First, you are using the ip address 127.127.1.0 which is the referenced used for the local system clock, the asterisc means is the preferred option as there is no other IP available. This is not a good practice and not recommended.
Secondly the stratum is unreliable, meaning too high to reach or too low to be accepted by Unity Connection.
If you would happen to run 'utils diagnose test' you would have probably seen an output as the following example below:
admin:utils diagnose test
Log file: platform/log/diag1.log
Starting diagnostic test(s)
===========================
test - disk_space          : Passed (available: 25680 MB, used: 7849 MB)
skip - disk_files          : This module must be run directly and off hours
test - service_manager     : Passed
test - tomcat              : Passed
test - tomcat_deadlocks    : Passed
test - tomcat_keystore     : Passed
test - tomcat_connectors   : Passed
test - tomcat_threads      : Passed
test - tomcat_memory       : Passed
test - tomcat_sessions     : Passed
test - validate_network    : Reverse DNS lookup missmatch
test - raid                : Passed
test - system_info         : Passed (Collected system information in diagnostic log)
test - ntp_reachability    : Passed
test - ntp_clock_drift     : Passed
test - ntp_stratum         : Failed
The reference NTP server is a stratum 11 clock.
NTP servers with stratum 5 or worse clocks are deemed unreliable.
Please consider using an NTP server with better stratum level.
Please use OS Admin GUI to add/delete NTP servers.
skip - sdl_fragmentation   : This module must be run directly and off hours
skip - sdi_fragmentation   : This module must be run directly and off hours
test - ipv6_networking     : Passed
And on the RTMT (Real Time Monitoring Tool) you would have seen a Critical event:
Condition:
The best external NTP server, , is stratum , which is unacceptably high. External NTP servers must be <= strata 8 and should be <= strata 5. NTP server strata can be verified using the CLI 'utils ntp status' command ('st' column). Try using different NTP servers.
Problem cause:
All specified external NTP server(s) have unacceptably high stratum values. Network issues exist or the designated servers have unreliable stratum values.
Information is self explanatory and therefore reassures the need of having a NTP different from the server itself.
By the snippet you sent we can know that it is the publisher server, as the Subscriber polls this information from the Publisher.
Installing the Operating System and Cisco Unity Connection 8.x
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/installation/guide/8xcucig020.html
"Cisco recommends that you use an external NTP server to ensure accurate system time on the publisher server. Ensure the external NTP server is stratum 9 or higher (meaning stratums 1-9). The subscriber server will get its time from the publisher server"
Documentation also reaffirms the need for that NTP to be accessible otherwise your system can be degraded. Some addtional information which would be interesting to know is:
- Why did they had to restart the NTP in the first place?
System Requirements for Cisco Unity Connection Release 8.x
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/requirements/8xcucsysreqs.html
"A network time protocol (NTP) server must be accessible to the Connection server"
On the Cisco Unity Connection Serviceability> Tools> CLuster Management screen shot you sent i see that the ports were "Not Available" and that the customer stated "there was no service for 5 minutes".
By no service did they mean that over the phone they heard a disconnected tone or a failsafe message?
Additionaly after the servers resolved from SBR the Subscriber never recovered entirely as it did not start the Conversation Manager service.
Bottom line if they are able to reproduce it then it would be worth a while checking with TAC
Best regards,
David Rojas Peck
Cisco TAC Support Engineer, Unity
Email: [email protected]
Mon, Wed, and Fri 12:00 pm to 9:00 pm ET, Tue and Thu 8:00 am to 5:00pm ET
Cisco Worldwide Contact link is below for further reference.
http://www.cisco.com/en/US/support/tsd_cisco_worldwide_contacts.html

Cisco Unity Connection not relaying voicemails outside the organization

Hi all, we are running Cisco Unity Connection version: 8.6.2ES25.21900-25. It has been set up to accept voicemails for Exchange 2010 users (in other words email messages with WAV attachments) and deliver these to their inboxes; this works with no problem.
I have two users who would like to receive these emails at their outside account, however the messages are never sent. I have tried the following:
Changed the users corporate email addresses from "[email protected]" to "[email protected]"
Unchecked the option to "Generate SMTP Proxy Address From Corporate Email Address."
On the "Message Actions" page for their account I have configured voicemail and email to "Relay the message" and entered their external SMTP addresses.
Confirmed the smart host setup is OK (points to our Exchange 2010 CAS which has firewall rules in place to permit it to send mail outside the organization.
Confirmed the Exchange 2010 CAS will accept SMTP messages from the subnet the Unity Connection server resides in.
If I switch the user SMTP settings BACK to their original internal SMTP addresses for my company the messages are then immediately delivered properly to these addresses. This signifies to me that Unity is periodically trying to send these items but they just aren't going out. No sign of the messages in any user report I ran in Unity nor message tracking in Exchange.
I also tried setting up an Outlook rule to forward these voicemail messages to the recipients external addresses but this did not work and after doing some research I see that the way in which Unity delivers the messages to these recipients internally (via EWS) is the reason why. I wonder if this is the same reason these are not going out to their external SMTP addresses.
Thanks for any assistance provided!

Look at the transfer options for that particular user and make sure it's set to ring the phone, that configuration is PER user.
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

What hardware is required to activate application like Cisco Unity Connection ?

Please I need your help,
What hardware is required to activate application like Cisco Unity® Connection ?
Thank you

In addition to great reply (+5), basically this is similar to CUCM which you need to have in order to run Unity Connection (or you could have CME). So, if you have CUCM running it will be very similar concept. If this is new install you want to definitely go the virtual path.
HTH,
Chris

Bluetooth Serial and Cisco Console connections?

This may be the wrong forum for this, but network management was the closest fit i could find...
(First off, I agree that console connections are not preferred, SSH, HTTPS, SNMP all have their advantages, but when something goes down or stops responding to normal methods the amount of time and frustration that can be saved by not having to search for "that one laptop that has a serial port" or "my specific laptop that has the USB-Serial driver installed" is invaluable.)
With the proliferation of tablet devices (ipad, cius, samsung's proposed, etc.), add to it a serious lack of serial ports on most laptops/netbooks/etc being released. It's getting harder and harder to connect to console ports on cisco devices. USB to serial adapters fit the bill for now, provided you had the right drivers to run the adapter on your device (read: doesn't address tablets and smartphones).
I understand that the cisco console connection is considered "legacy" and that USB connections are becoming more popular with newer Cisco devices, but in the meantime it would be nice to manage my slice of the millions of "legacy" devices out there.
Bluetooth serial seems to hold promise, though the serial features of bluetooth aren't typically incorporated into most devices right now. What i guess I'm looking for is a way to manage my router and switch console ports from a smart phone or tablet device.
Has anyone seen anything like this out there right now?
I would think that Cisco would be interested in marketing such a feature with their new Cius, or an iPod or Android app. Even if it cost a couple of bucks for the adapter or the software, it would be well worth it to be able manage these devices in a pinch.
Thanks to anyone that can help!
JM

I agree, it wold be handy to have.
One thing some of us use is iSSH on the iPhone or iPad. Straight across the in-house wi-fi LAN if there's a working one in house or via the VPN tunnel if not. The use cases of no w-fi, no VPN or an unresponsive box are still not addressed by that solution though.

Cisco VPN connects but then no services are available.

Where to start:
I have a situation where by my remote office, 5 machines, connects to head office via Cisco VPN client.
Recently we have been able to make a vpn connection but once connected we have no services available like connecting to servers, internet, network drives, voip phone or even pinging any of the services. We get an IP address on the virtual network adaptor created by vpn connection but then nothing.
After a hec of amount of troubleshooting I swapped out our router, Draytek Vigor 2820, for another 2820. Same problem. I then took my Draytek Vigor from home, that does work, to the office and it works perfectly fine using the 2600 router in the office. I then tried a dlink router and that worked in office as well. So it has something to do with the 2820 router. It has been working fine for months and now recently, having changed nothing on it, it has stopped working for us with Cisco vpn connection. Does anyone have any clues as to why and what I could do on the router to resolve issue or could it be something on the cisco side that needs changing? I have already updated firmware to latest version on router.
Any help / advice would be great appreciated.
Regards,
Ashley

Can you please share the configuration as there might be something that change after the upgrade that might cause the issue.

Setting up Directory Handlers under Cisco Unity Connection

Good Day All,
I am in the process of setting up directory handlers for Cisco Unity connection.
When I dial the extension for the directory handler ; I hear the default Cisco Unity connection greeting instead of being prompted for the search.
Can anyone shed any light on why this is happening?
Any help is greatly appreciated.
Thanks very much
Regards
Amanda

Hi javalenc,
Of course , that was right. I worked it out in the end.
I was trying to copy the configuration from an older version of CUC and basically added an un-needed call forwarding rule under the Directory Handler. As soon as I removed it; the directory worked normally.
The other thing I learned last weekend was that the order of the routing rules is important.
My directory had the first priority and it was causing people who wanted to leave a voicemail for other users to get the prompts for the directory.
Thanks so much for the help though.
Regards,
Amanda Lalli-Cafini

Regarding Transfer speed in Cisco Any Connect

Hi,
I was trying to check transfer speed from Cisco Any Connect, with only ports opened in firewall 443 & 80 with 1 destination , but to complete data transfer of 50MB file it takes around 40mins, but if all ports are unblocked in Firewall with 1 destination ,it takes only 9mins.
so wanted to know the correct port numbers which needs to be opened to make data transfer speed fast & why this behaviour.
Please somebody help me.

a customer has confronted me with a similar issue. They are using AnyConnect SSL Clients in their LAN, and noticed a severe performance drop on client side once connected via AnyConnect. I have set this up in a lab environment to compare LAN performance with AnyConnect SSL performance.
Win7 Client
AnyConnect ASA5520 Win7 iperf Server
Secure Mobility -----------1Gb LAN---------------- v9.1.1---------------------1Gb LAN-------------------- TCP Window Size 4MB
3.1.02040
The ASA was configured from factory default and there was no traffic passing besides this test. AnyConnect used DTLS, and interface mtu on the ASA was 1500, the AnyConnect mtu was left unmodified, so I suspect the maximum of 1406 bytes was used.
Result:
- While AnyConnect was disconnected, Iperf reported bandwidth usage of about 300Mbps. This was what I was expecting.
- As soon as I was connected via AnyConnect, the bandwidth usage dropped tp about 80Mbps. I expected a slight drop, but not this much.
What causes such decrease in performance? Sure, if connected via the Internet, clients will most likely never notice this, but the customer uses AnyConnect SSL in a Gigabit LAN environment. Could the bottleneck be on the client side? The load and memory usage on the ASA side was very low. I have tried several ASA versions, but they all deliver similar results.

Cisco Anytime Connect VPN working from iMac but not from MacBook Air with same settings and wifi network

Hi guys,
I'm having trouble connecting my new MacBook Air to Cisco Anytime Connect VPN.
The same configuration works with my iMac, in the same network and same Mac OS Mountain Lion on both computers.
After successfully connecting to VPN after a few seconds it gets disconnected and, what is worse, WIFI is not working any more in my macBook Air, I need to deactivate it and start again.
With iMac with the same settings it doesn't happen.
Any ideas?
Thanks!

Did you power cycle the network? That's always the first thing you want to do if a device is "missing" or not connecting to your network correctly.
If you have not already tried this a few times, power down the entire network...all devices, order is not important.
Wait a few minutes and place the MBAir close to the TC
Start the modem first and let it run a few moments by itself. Then start the TC if it is the device connected to the modem and let it run a few moments. Then start each device one at a time the same way.

Cisco Speech Connect Network Fault Tolerance

Hi,
I have redundant core network infrastructure. Is there any way to do Network Fault Tolerance in cisco speech connect like the one in Cisco CallManager (5.x and later)?
Thanks,
Ashraf

As of the latest version of Speech Connect version 1.0.3 there is no support for Network Fault Tolerance.
You could speak to a Cisco account rep and request this feature enhancement be considered for future versions.
Thanks,
Scott

Cisco 7507 connected to a Lucent Stinger

Similar Messages

Maybe you are looking for