Cisco SCE - TA Adapter

Hi All
I have a question here, I'm now analyzing the subscriber hourly usage volume per hour. As I know, the data Top Subscriber Report in the BB Console is collected by Topper/Aggregator (TA) Adapter inside the Collection Manager (CM) server. Could anybody help me explain in detail on how is the TA Adapter works?
Thanks very much
Mohd Farhan Tajuid
IPSC Implementation
Core IP Development

Hello Mohd,
This question is a bit vague. Have you read the following document?
http://www.cisco.com/en/US/docs/cable/serv_exch/serv_control/broadband_app/rel36x/cmug/Collection_Manager_Overview.html#wp1044982
If yes, which part you think requires deeper explanation?
Cheers,
Tom

Similar Messages

Cisco SCE 8000 rebooting

Hi!
Cisco SCE 8000 working normally while traffic through it not pass. When i connect optical links and start passing traffic throught cisco, i have a problem. SCE watchdog run software reboot with error:
2013-09-30 13:54:40 | FATAL | CPU #000 | A problem occurred in the SCE8000 Service Control Module Extended (SCM-E) slot 1 ,Please report to Cisco's customer support.
2013-09-30 13:54:40 | ERROR | CPU #000 | SE Watchdog Module: An Error occurred. Please report to Cisco's customer support
2013-09-30 13:54:40 | ERROR | CPU #000 | SE Watchdog Module: An Error occurred. Please report to Cisco's customer support
2013-09-30 13:54:41 | WARN | CPU #000 | SE Watchdog Module: A problem occurred. Please report to Cisco's customer support
2013-09-30 13:54:41 | INFO | CPU #000 | Party data base was closed.
In debug file i found:
Interrupt Received from: SimbaDPT[0].Tx[0].CTX_ISR.ECCMultiErrorInt - description: RLDRAM ECC multi bit error interrupt.
What the problem could be?

I have tried 3.7.2, 3.8.5, 4.0.0. Unfortunately, the result is the same. I think that hardware problem (RAM).

Cisco SPA 112 adapter Issue

Hi All,
We are using Cisco SPA 112 adapter and it is having 2 lines,I configured both of the lines.
There is no issue in line 1 but line 2 is automatically went to disable mode.After that i have to manually enabled that option.
Please help me to fix this issue

Dan, i will see how it goes over the next week or so with the updated F/W & shall report back, and thanks for the link as i wasnt sure how to save a syslog.
Should i set the verb as high as 6, or is that an over kill.
Gabriel, I have an FTP running on my sat receiver which i will attempt to use to catch the log, but as for the the "sipgate registration", when i loose conection my ata reports its still registered & the sipgate URL, isnt in real time as far as i can tell.
My ata would have normally shown its fault since my first post 6 days ago, but unfortunately a recent power cut has reset my testing period back to 1 day.

Cisco SCE 2020 and SNMP

I am trying to figure out how to retrieve the output of the comannd "show party all-names" via SNMP.
Does anybody have some suggested OID strings I could try?
here is my sh ver:
sce1#sh ver
System version: Version 3.6.0 Build 716
Build time: Mar 28 2010, 12:34:53 (Change-list 600192)
Software version is: Version 3.6.0 Build 716
Cryptography class: K9
Hardware information is:
rx            : 0x0079
dp            : 0x1d08
tx            : 0x1712
ff            : 0x0077
cls           : 0x1e05
cpld          : 0x0025
lic           : 0x0202
lic-drv       : 0x02020000
lic-prm       : 0x02020000
rev           : G001
Bootrom       : 2.1.0
L2 cache      : Samsung 0.5
lic type      : 4GBE
optic mode    : MM
Product S/N   : CAT1425G00V
Product ID    : SCE2020-4XGBE-MM
Version ID    : V04
Deviation     :
Part number       : 800-26601-08
Revision          : C1
Software revision : G001
LineCard S/N      : CAT1422G00Z
Power Supply type : AC
SML Application information is:
Application file: /tffs0/release_.sli
Application name: Engage SML Version 3.6.0 build 126 (Protocol Pack 21 build 24)
Using Lib - PL_V3.6.0PP_B24
Using Lib - Classifier_V3.6.0_B24
Application help: Entry point of Engage
Original source file: /auto/srbu-proj1/apps/users/obenreph/autoBuild/App/SML/Engage/V3.6.0/src/com/pcube/AppTemplate/Main/template_app_main.san
Compilation date: Mon, April 26, 2010 at 09:04:40
Compiler version: SANc v3.20 Build 14 built on: Tue 08/04/2009 06:58:22.;SME plugin v1.1
Capacity option used: 'EngageDefaultSCE2000'.
Logger status: Enabled
Platform: SCE2000 - 4xGBE
Management agent interface version: SCE Agent 3.6.0 Build 429
Software package file: ftp://ftpserver/C:\Documents and Settings\btadlock\Desktop\scos-v360-b716-sce2000-k9.pkg

Hi Olaf,
The lwapp APs are not snmp-manageable but the controllers takes care of that. You can poll the WLC via SNMP and it will give you the radio status of all the APs.
I suggest using the Cisco MIB browser tool to find out more about the AIRESPACE mib that the WLC is using.
Nicolas

802.11n (CISCO?) client adapter

Hello,
after the release of the 1250AP, I was wondering if the 802.11n compatible client adapters were planed or close to release, and if anyone had an information about that.
I was also wondering if this AP had any particular CISCO features (like there was in some previous versions) that could require such an adapter to work properly?
Regards,
Laurent

Cisco's 1250 series APs have been selected as the test hardware for all 802.11n Draft 2.0 client adapters. That means that for any Draft 2.0 compliant hardware to be certified, it must inter-operate with the 1250 series AP. There are some additional features that Cisco makes availible to client adapters (CCX, for example), but any Draft 2.0 certified client adapter should work with the 1250 without any problem, regardless of CCX version support.
Below is from the Cisco Aironet 1250 Series Access Point Q&A:
Q. What is the status of the Draft 802.11n version 2.0 standard?
A. The IEEE 802.11n working group has passed letter ballot, and this is what is known as 802.11 Draft 2.0. Subsequently, the Wi-Fi Alliance commenced compatibility testing in June 2007 to ensure interoperability of products adhering to the 802.11n draft 2.0 standard. The Cisco Aironet 1250 Series Access Point was selected as the reference platform for the Wi-Fi Alliance test bed. All products receiving Wi-Fi Alliance draft 2.0 certification must be tested with the Cisco Aironet 1250 Series Access Point.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps6973/ps8382/prod_qas0900aecd806b7c82.html

Cisco SCE - RDR length

We need to estimate the length (bytes) of RDRs generated by SCE.
In particular we are interested in the following RDR types:
- HTTP Transaction Usage RDR
- Transaction Usage RDR
- Subscriber Usage RDR
Any suggestion is appreciated.
Thanks,
Marco and Fabrizio

The RDR lenghts would vary but you can take a look at this link to confirm the size of each field.
http://www.cisco.com/en/US/products/ps6135/products_technical_reference_chapter09186a00808484a7.html
You will see lengths as :
INT32 : 32 bit integer
INT16 : 16 bit integer
STRING : Variable string length ( I believe it is 256 characters)
Basically they are the same types as you would find in a database.
Hope this helps.
Shelley.

CISCO CSS 11503: Adaptive Session Redundancy + Resets

Hi
we have release 7.10.206a configured with SourceGroup and ASR. I made a sniffer trace and experienced that the CSS sends a lot of RST. As well I saw that it use only 1984 source ports for the connections to the server. How can I increase the number of source Ports? .In the attachments you will find the sniffer trace with the incorrect behaviour and the configuration.
Any suggestion, idea ?

the problem of the RST seems to be the frequent reuse of the same source port.
The destination of this connection seems to be confused and ACK the new SYN with the ack number of the previous connection. This ack number is out of range from the syn sequence number so the result if a RST.
ie:
Flow1 - Syn -> packet 1
Flow1 - Last ACK -> packet 33
Flow 2 - syn -> packet 34
Flow 2 - ack (instead of syn/ack) with acknumber same is packet 33.
This triggers a RESET -> packet 36
Flow 3 - syn -> packet 55
Flow 3 - same as flow 2 issue, ack with old ack number. This triggers a RST (packet 57).
Now the 2nd issue, the CSS (I believe tpkg0x.post.ch is the CSS) sends packet for flow 2 but the end station believes flow 2 was killed with the RESET of flow 3 and the host sends a RST to the CSS (packet 59) because its connection does not exist anymore.
So the all issue is the fact that ports are being reused to quickly.
You will need to involve more people to find a workaround to the 1984 ports available [and be aware they are available but not all usable].
Work with Marco K., your sale support.
Regards,
Gilles.

Cisco USB adapter to Virgin HUB?

I am thinking about upgrading to a faster fiber optic broadband offered by Virgin Media. This new set up will involve a combined modem and router known as the Virgin HUB. However I currently have a seperate virgin modem connected to a Cisco Router. To connect to this router wirelessly I am using Cisco USB WIFI adapter.
The question is, if I know longer have a cisco router, will my Cisco USB adapter be able to connect to a non Cisco routers?
Thanks
Solved!
Go to Solution.

Technically it should. As long as the router is wireless capable, it should connect.

Cisco VPN client install fails with Error 1722 on Windows 7

Hi,
I am having issues with laptops upgraded from Vista to Windows 7.
Prior to the upgrade they are running Cisco VPN Client 5.0.05.0290. These laptops also have Juniper Network Connect 6.5 and Citrix web client installed. The windows upgrade advisor made no recommendations regarding uninstalling / reinstalling these apps.
I have done an inplace upgade to Windows 7 (Windows Vista Enterprise 32bit to Windows 7 Enterprise 32 bit) and after the install the Cisco client is not working. Uninstalled the client (the uninstall was successful) then reinstalled and the installation fails at Installing Cisco Systems Virtual Adapter - error 1722 there was a problem with the windows installer package.
I have followed the steps for a manual uninstall of the Cisco client and then tried the install again - still not successful. Interestingly (or not) the Juniper Network Connect also fails with the error The Network Connect Virtual adapter driver is not installed properly. This also fails to reinstall after being removed.
I tried removing the VPN clients on another laptop and then running the upgrade but the same errors occured when reinstalling the VPN Client. I have tried the Winfix and DNE patch from Citrix but these fail saying there is a corruption in the application.
On another laptop where only the Cisco VPN client was installed a reinstall was required after the upgrade, but it did install successfully.
On a clean image these applications all install fine, however I have a large number of laptops do upgrade and don't want to do a fresh install and settings migration on all of them.
What files / registry entrys are involved with the DNE adapter so I can manually clear it all out before reinstalling?
Anything else I can do to troubleshoot this issue?
Cheers,
James

You should be able to install the 64 bit version of the Cisco VPN software
Latest version is vpnclient-winx64-msi-5.0.07.0440-k9.exe
You should download and run MCPR.exe first, to clean out any traces of McAfee products that conflict with Cisco VPN.
http://download.mcafee.com/products/licensed/cust_support_patches/MCPR.exe
If there is a problem with vbscript registration on the system - there is a fixit tool from Microsoft for that:
MicrosoftFixit50842.msi
(Using Shrew VPN is a possible workaround.)

Is there any one who knows how to apply machine learning algorithms to the spectrum data collected using ni usrp for ism band to use spectrum efficiently by link adaptation

Hi,
may i know any one working in cognitive radio research and applying machine learning techniques using the spectrum data collected from NI usrp kits

Can't edit my message anymore, so for the tldr crowd (too long didn't read), here is a shorter version:
The good:
E4200 worked fine for about 15 hours with great throughput and link quality (with one brief disconnect in the middle - online gaming software shows brief disconnects that otherwise go totally unnoticed).
The bad:
Wireless on the E4200 stopped broadcasting entirely (to a Windows 7 laptop with a 802.11n 2.4 GHZ USB adapter).
I had switched between two adapters that use the same chipset, same driver and in fact show up as a single device in device manager) without rebooting the router but it worked (fine) for an hour after I swapped the adapters.
Right before I rebooted it, I checked and the E4200 was not hot to the touch and wired internet was still working after the wireless radio stopped working.
A reboot of the router cured it.
The open question as to the root cause:
Now I want to know whether this wireless radio ceasing to broadcast (requires a reboot of the E4200) will happen daily?
I.e. I want to know whether it it really is overheating (then again why would only some have that problem needing to reboot daily while others have gone weeks with the E4200 without a single reboot being needed and without any problems occurring) or whether it had to do with changing the adapters back and forth without rebooting the router. Keep in mind that the router worked fine for an hour or so after I stopped swapping the adapters.
Extra question:
Will getting a Cisco AE1000 USB adapter perhaps help? (I know this is a loaded question and their is no easy / sure answer, but even a "maybe" or reasons why it might help at this point would be better than nothing.
Any similar experiences (with the router needing to be rebooted to get wireless radio back on) would be appreciated as it may help myself and others experiencing these types of issues.

No Internet access after cisco vpn client connection

Hi Experts,
Kindly check below config.the problem is vpn is connected but no internet access
on computer after connecting vpn
ASA Version 8.0(2)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Ethernet0/0
nameif outside
security-level 0
ip address 192.168.10.10 255.255.255.0
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.14.12 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
access-list dubai_splitTunnelAcl standard permit 192.168.14.0 255.255.255.0
access-list INSIDE_nat0_outbound extended permit ip any 192.168.14.240 255.255.2
55.240
pager lines 24
mtu inside 1500
mtu outside 1500
ip local pool testpool 192.168.14.240-192.168.14.250
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list INSIDE_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.14.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set setFirstSet esp-3des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set setFirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
username testuser password IqY6lTColo8VIF24 encrypted
username khans password X5bLOVudYKsK1JS/ encrypted privilege 15
tunnel-group mphone type remote-access
tunnel-group mphone general-attributes
address-pool testpool
tunnel-group mphone ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:059363cdf78583da4e3324e8dfcefbf0
: end
ciscoasa#

Hi Harish,
Please check the o/ps below and route print in attached file
Latest ASA Config
ASA Version 8.0(2)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Ethernet0/0
nameif outside
security-level 0
ip address 192.168.10.10 255.255.255.0
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.14.12 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
passwd 2KFQnbNIdI.2KYOU encrypted
ftp mode passive
access-list dubai_splitTunnelAcl standard permit 192.168.14.0 255.255.255.0
access-list INSIDE_nat0_outbound extended permit ip any 192.168.14.0 255.255.255
.0
pager lines 24
mtu outside 1500
mtu inside 1500
ip local pool testpool 192.168.15.240-192.168.15.250
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 192.168.10.12 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.14.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set setFirstSet esp-3des esp-md5-hmac
crypto dynamic-map dyn1 1 set transform-set setFirstSet
crypto dynamic-map dyn1 1 set reverse-route
crypto map mymap 1 ipsec-isakmp dynamic dyn1
crypto map mymap interface outside
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
no crypto isakmp nat-traversal
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
group-policy mphone internal
group-policy mphone attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value dubai_splitTunnelAcl
username testuser password IqY6lTColo8VIF24 encrypted privilege 15
username testuser attributes
vpn-group-policy mphone
username khans password X5bLOVudYKsK1JS/ encrypted privilege 15
username khans attributes
vpn-group-policy mphone
tunnel-group mphone type remote-access
tunnel-group mphone general-attributes
address-pool testpool
tunnel-group mphone ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:12308d7ff6c6df3d71181248e8d38ba8
: end
ciscoasa#
Route Print after vpn connection
C:\>route print
===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x40003 ...00 24 01 a2 e6 f1 ...... D-Link DFE-520TX PCI Fast Ethernet Adapter -
Packet Scheduler Miniport
0x250004 ...00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter - Packet Schedule
r Miniport
===========================================================================
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.10.1 192.168.10.211 20
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.10.0 255.255.255.0 192.168.10.211 192.168.10.211 20
192.168.10.211 255.255.255.255 127.0.0.1 127.0.0.1 20
192.168.10.255 255.255.255.255 192.168.10.211 192.168.10.211 20
192.168.14.0 255.255.255.0 192.168.15.1 192.168.15.240 1
192.168.15.0 255.255.255.0 192.168.15.240 192.168.15.240 20
192.168.15.240 255.255.255.255 127.0.0.1 127.0.0.1 20
192.168.15.255 255.255.255.255 192.168.15.240 192.168.15.240 20
213.42.233.97 255.255.255.255 192.168.10.1 192.168.10.211 1
224.0.0.0 240.0.0.0 192.168.10.211 192.168.10.211 20
224.0.0.0 240.0.0.0 192.168.15.240 192.168.15.240 20
255.255.255.255 255.255.255.255 192.168.10.211 192.168.10.211 1
255.255.255.255 255.255.255.255 192.168.15.240 192.168.15.240 1
Default Gateway: 192.168.10.1
===========================================================================
Persistent Routes:
None
C:\>
C:\>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : asu
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection 7:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : D-Link DFE-520TX PCI Fast Ethernet A
dapter
Physical Address. . . . . . . . . : 00-24-01-A2-E6-F1
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.10.211
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.10.1
DNS Servers . . . . . . . . . . . : 213.42.20.20
195.229.241.222
Ethernet adapter Local Area Connection 8:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Cisco Systems VPN Adapter
Physical Address. . . . . . . . . : 00-05-9A-3C-78-00
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.15.240
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :

Cisco ISE and ATA 188 profiling.

I have tried to profile cisco ATA 188 adapter, based on cdp attribute;
Platform: Cisco ATA 188
and assigned to a create a same identity group. I am not able to see device profiled according to identity group assigned. Instead of it its always assigned to "cisco - device" group.
On cisco switch side, i am seeing device being in data domain instead of voice domain, but strange enough its getting ip address from voice dhcp pool. If dot1x configs are not applied on port device is getting ip address from voice vlan and working fine.
Any suggestion for this case?

Can you post a screenshot of the custom profiling policy that you configured?
Also, what version of code do you run on the switch and ISE

802.1x, enterasys roamabout R2, cisco 350 aironet without win2k active dir.

Can I set up a win2k 802.1x client authentication (win2k OS) using a cisco 350 aironet adapter via a roamabout r2 AP and get authenticated with a cisco ACS 3.0 radius server without having a win2k active directory domains ( i guess without using certificates)? I'm currently still using NT domains and having a WinNT PDC which I believe it will be a hassle to migrate win2k. If so, are there any documentation out there that can help me?

How to config anonymous subscriber in SCE 1010

Dear Experts
Jasmina
I have Cisco SCE 1010 and wanto configure anonymous subscriber configuration in SCE .
I have bb console installed in windows xp machine and which is connecting SCE 1010
For this scenario do we need SM / CM ?
now how CAN I control bandwith for http 1 MB and FTP 2MB for anonymous users.
Please kindly Advise
Thanks

Dear Experts
Jasmina
I have Cisco SCE 1010 and wanto configure anonymous subscriber configuration in SCE .
I have bb console installed in windows xp machine and which is connecting SCE 1010
For this scenario do we need SM / CM ?
now how CAN I control bandwith for http 1 MB and FTP 2MB for anonymous users.
Please kindly Advise
Thanks
Hi,
Check out the below link hope that help !!
http://www.cisco.com/en/US/products/ps6134/products_configuration_guide_chapter09186a00808498ac.html#wp1048171
Ganesh.H
If helpful do rate the post

Cisco VPN Client Version 5.0.07.0440

Upgraded to windows 8.1 and now cisco VPN not working
Error message
'SECURE VPN CONNECTION TERMINATED LOCALLY BY THE CLIENT
REASON 440: DRIVER FAILURE
Any help to resolve this would be appreciated. Thank you

The Cisco VPN tends to have compatibility issues in Windows 8 & 8.1. You need to apply a small workaround as explained below –
1. Open Registry editor by typing regedit in Run prompt
2. Browse to the Registry Key HKEY_LOCAL_MACHINE\\SYSTEM\\CurrentControlSet\\Services\\CVirtA
3. Select the DisplayName to modify, and remove the leading characters from the value
data upto "%;" i.e.
- For x86, change the value data from something like "@oem8.inf,%CVirtA_Desc%;Cisco Systems
VPN Adapter” to "Cisco Systems VPN Adapter”
- For x64, change the value data from something like "@oem8.inf,%CVirtA_Desc%;Cisco
Systems VPN Adapter for 64-bit Windows” to "Cisco Systems VPN Adapter for 64-bit Windows”
- Try connecting again
Hope this will help.

Cisco SCE - TA Adapter

Similar Messages

Maybe you are looking for