Cisco Works Polling and threshold

Hi,
Is it possible to sechedule polling for config backup and threshold based on device group (for eg all device in group a at 11:00 PM and devices in group B at 00:00 hrs etc)

Which version of LMS is this?
You can go to RME - Admin - Config Management - Collection settings to schedule period config backup for devices.
In DFM you can go to DFM - Configuration to threshold polling for groups.

Similar Messages

DFM@LMS4.0.1 - no devices for Polling and Thresholds

Hello,
DFM with LMS4.0.1 got all wanted devices and is working fine so far except of we cant do settings on Polling & Thresholds, because we cant select anything:
How can we solve the problem? Many thx for hints in advance,
Steffen

This is expected. You can only adjust polling and threshold parameters on groups. You cannot select individual devices. If you want to be able to control polling parameters or thresholds at the device level, you will need to customize one of the customizable fault groups to match the devices in question. Then you can adjust the polling and threshold group priorities so that customizable group is closer to the top. Apply your changes, then go and adjust the desired settings.

Cisco Works server install

All,
does anyone know the best practise install in respect to partitions, O/S, and what locations the log files should be placed? We recently upgraded from an old Cisco Works platform and now our full CW is broke
So can anyone recommend any best practise scenarios?
We have 4 x 146 gb disks that we could utilise.
Thanks in advance,
Tam.

Is your environment Windows or Solaris? Did you upgrade your hardware platform only or also change from an earlier LMS version to the lastest (4.0)?
Generally speaking, the installation guide has a good number of details. If you follow it carefully, your should have a successful installation. As with many products, when upgrading it is usually most successful to back up the data on the old system and do a clean install on the new, restoring the data after verifying a basic working system.

Cisco Works Error

Hi ,
I have a Cisco work server and i am facing problem with the Netconfig job failure.It fails the job with following error.
" ERROR:RME_CDL1032:Synchronization of the running configuration before deply,has failed" and also i am seeing the following error as " cm0012:Unable to create new version on archive $1 " Action : Check if disk space is available and directory has required permission.
LMS version : 2.6
RME Version : 4.0.5
Please let me know if you have any idea on this error.
Thanks in advance
Thanks & Regds,
Lalit

CM0012 error is a bug - "CSCsh39475 ConfigMgmt CM0012: Unable to create new version on archive". The patch is posted on CCO.

Cisco Works LMS 3.2 backup takes too long time to finish

Hello guys,
We have problem with scheduled LMS 3.2 backup. It takes more than 12hours to finish. You can see in log that backup is scheduled for 18:00h and it waits untill 22:07 to start doing anything. We can't figure out why is there such a delay. It started to happen after system reported lack of free space on disk. And we feed up the space, but then faced this problem with long duration. Before this problem occured backup used to last for 45 min od 1 hour.
Backup to 'C:/BACKUP' started at: [Mon Apr 11 18:01:26 2011]
Apps file : D:\\PROGRA~1\\CSCOpx\\backup\\manifest\\campus\\properties\\datafiles.txt
[Mon Apr 11 22:07:07 2011] Archiving the contents of the following directories into C:\BACKUP\2\campus\filebackup.tar
[Mon Apr 11 22:07:07 2011] D:\PROGRA~1\CSCOpx\campus\etc\cwsi\DeviceDiscovery.properties
D:\PROGRA~1\CSCOpx\campus\etc\cwsi\ANIServer.properties
D:\PROGRA~1\CSCOpx\campus\etc\cwsi\ut.properties
D:\PROGRA~1\CSCOpx\campus\etc\cwsi\discoverysnmp.conf
D:\PROGRA~1\CSCOpx\campus\etc\cwsi\datacollectionsnmp.conf
Do you have any ideas what went wrong and how to fix it?
Thanks,
Marija

This is a catch 22 , you need to apply a patch to fix a backup problem , yet you want to backup before applying a patch. This is where you will have to assume some risk, and apply the patch w/o a backup.
Go to Common Services -> Device and Credentials -> Device Mgmt and export the entire DCR (All devices) to a CSV file. Make sure you browse to someplace outside application space, I usually place the file at c:\. Also make sure you check mark the include credentials box, so you also have all your device passwords. This is your D/R plan, if things were to fail you will have your device list you can import in an emergency.
Or you can try the suggestion of clearing DFM to mitigate potential loss so you can get a good backup of the rest of LMS. Just be sure to view your notifications and cut/paste into note pad so they can be rebuilt. You will lose history and local customizations to Polling and Thresholds and DDV.
# net stop crmdmgt
kill any sm_* / brstart processes still running
# cd ...\CSCOpx\bin
# perl dbRestoreOrig.pl dsn=dfmInv dmprefix=INV
# perl dbRestoreOrig.pl dsn=dfmFh dmprefix=FH
# perl dbRestoreOrig.pl dsn=dfmEpm dmprefix=EPM
Use explorer to go to ...\CSCOpx\objects\smarts\local\repos\icf and delete all .rps files
perform the backup.

Cisco Works - need to re-use a 3560, how to delete and re-add in Cisco Works

Hello. I did not see a cisco works section on the forum, forgive me if it's there and I missed it. I have removed a 3560 switch from one location and am going to rename it (same IP though) and deply it in a different department. We have cisco works sending critical and informational alerts as well as backup the configs on Sunday mornings. I think I was able to get it to stop sending alerts when I unplugged and unhooked the switch. I want to give the switch a new host name and re-deploy it. I assume it will be easier to delete and then re-add the switch to cisco works. Is the a document where I can follow steps to remove it from cisco works? I have the documentation, but it is hard to read and they don't really have an area that specifically says "remove a switch from cisco works", and I don't want to break everything for the other 55 switches that cisco works does do the alerts and backups for. I know cisco works is full of different modules, so I was wondering if there was a document or some type of help I could get for doing this. Any help would be greatly appreciated. Thanks. Mike Baker

Hi,
It sounds like a tutorial may be what you are looking for. Here is one based on LMS 3.1.
https://learningnetwork.cisco.com/docs/DOC-4031
To remove a device from DCR (Device & Credential Repository) navigate to Common Services > Device and Credentials > Device Management.
Thanks,
Nick

I have Cisco TelePresence SX10 and content sharing is not working when I am dialing through the bridge

I have Cisco TelePresence SX10 and content sharing is not working when I am dialing through the bridge, I can share the content if I drag and drop from RMX, but if schedule the call in Resource manager or manually dial in from device the content is not going to other hand, I have tried to turn off encryption as well but still same issue. can you please help me out with this. I am from Lion co and purchased sx 10 recently.
regards
Hemang

Can you please provide us with a little more information on your systems and configuration / topology, such as, what call control are you using (Cisco VCS, CUCM, other?). what type of "Bridge" are you using (is this a Cisco MCU, or Cisco TelePresence Server, or other device?), what versions of the software are on each of the devices, etc. The more information we have about your environment will help us assist you better. But saying that, if all your core equipment isn't Cisco, you may have more luck in the forums for the manufacturer of such equipment (ie Polycom's Support Community).
Wayne
Please remember to rate responses and to mark your question as answered if appropriate.

ACS and Cisco Works

I have landed a pretty big WLAN roll out. 75 1231 WAP's and ACS for authencation and Cisco Works with WLAN engine installed. ACS Radius should be the straight forward to configure has anyone run into any gotchas installing it. Cisco Works also should be straight forward. One other thing is Cisco no longer sales Site Survey Kits so I have to piece mill one or two from scratch. Is there a Cisco partner that sells them.

check here for some information on WLAN:
http://www.cisco.com/pcgi-bin/Support/browse/psp_view.pl?p=Technologies:Wireless_LAN_General&viewall=true

ACS and Cisco works integration

I have authenticated cisco works with ACS as cwadmin. I am not able to view the device added through tacacs+ authentication. But the device is searchable through ip address in chasis view and am able to configure it. Please suggest a method to view the device in device management and device centre.

I have reinstalled cisco works and again added devices in acs mode. it works now. Thank you. But now the problem is it doesnot list in campus manger, or vlan port assignment. can i know any configuration is required for this?

How to install Cisco Work 3.2 on Windows 2008 Server Standard R2

Hi Everyone,
I have got Cisco Works LAN Management 3.2. But the problem is that i have a Windows 2008 Server Standard R2 and when i try to install, it fails. What I read from the below link is that it supports
"Windows 2008 Server Standard and Enterprise Edition with Service Pack 1 and 2. Both 32-bit and 64-bit operating systems are supported on the above versions."
http://www.cisco.com/en/US/partner/prod/collateral/netmgtsw/ps6504/ps6528/ps2425/data_sheet_c78-534877.html
Please help me out on how i should install on the Windows 2008 Server Standard R2. If there is any patch or any other way out.
Awaiting your response.
Farid

Hi ,
LMS 3.2 is not supported on Windows 2008 Server Standard R2.
here is the supported platoform for LMS 3.2
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/install/guide1/prereq.html#wp1110367
Thanks,
Gaganjeet

Cisco Phone Control and Presence 8.6.1.1185 with IBM Lotus Notes 8.5.2 (Integrated Sametime Client 8.0.2) - No presence status visible

Hi community,
I am trying to integrate Cisco Unified Presence 8.6.1.10000-34 with IBM Lotus Notes 8.5.2 with the integrated Sametime Client version 8.0.2 via the Cisco Plugins 8.6.1.1185.
Phone control is working fine, whereas the presence status is not shown (= no handset symbol next to the Sametime user). When I look in the preferences of the plugin, I can see that the plugin has connected successfully to the CUCM (8.6.2.20000-2),whereas the connection to the CUPS has not been established.
The user id as well as the password are all the same on all systems. Here is a description of what I have configured via the ciscocfg.exe tool:
Feature Control:
- Enable Phone Status -> checked
- Enable Dial Using Cisco IP Communicator -> unchecked (not required)
- Enable Control Desk Phone -> checked
- Default Mode -> Control Desk Phone
Control Desk Phone Settings:
- Voicemail Pilot Number -> left blank (no voicemail)
- Cisco Unified Communications Manager
     - Servers -> IP address of CUCM
     - Read Only -> unchecked
     - Use as Default CUCM -> checked
     - Synchronize Credentials -> checked
          - Use Sametime Credentials -> checked
Use Secure Connection: -> not required
LDAP Phone Attributes: -> not required
Phone Status Settings:
- Cisco Unified Presence Servers -> IP address of CUPS
- Read Only -> unchecked
- Synchronize Credentials -> checked
     - Use Sametime Credentials -> checked
- Sametime User ID Mapping
     - Use Business Card Attribute -> MailAddress
     - Remove Domain -> checked
- Display Off-Hook Status Only -> unchecked
At the moment I don't see an error in the configuration, but maybe I am wrong. Could anyone please tell me what the error could be?
Thanks a lot in advance!
Kind regards,
Igor

Hi all,
here are some additions to my above post:
Servers and clients used:
1x CUCM 8.6.2.20000-2
1x CUPS 8.6.1.10000-34
1x IBM Lotus Domino Messaging Express Server 8.5.2
1x Sametime Entry Server 8.5.2 (on top of the Domino server)
2x IBM Lotus Notes 8.5.2 with integrated Sametime 8.0.2
2x Cisco Phone Control and Presence with Lotus Sametime (PCAP) 8.6.1.1185
2x Cisco Unified Personal Communicator 8.5.5.19839
Setup:
- CUCM, CUPS and CUPC are working fine, i.e. Desk Phone control via CUPC, as well as availability and presence status are working without issues
- IBM Lotus Domino server is the LDAP Directory, the Sametime Entry Server is installed on top of the Domino server and uses the Domino Directory
- User ID and password on CUCM/CUPS match the ShortName field and password in Domino
- The PCAP plug-in has been manually deployed to both Notes clients with the following configuration:
     - Enable Phone Status -> active
     - Desk Phone Control -> active
     - no credential synchronization for CUCM and CUPS, i.e. every user must fill the user details himself
     - Sametime User ID Mapping is implemented via the LDAP Attribute uid (which is equal to the user id in CUCM)
     - LDAP configuration filled in with details of the Domino server
Phone Control is working fine, also the connection to the LDAP server (Domino) is fine. However, when I type in the credentials for the CUPS server login, I can see (in Troubleshooting pane) that the user (pparker) is connected to the CUPS server for a short period of time and then gets disconnected. After that no connection is possible to the CUPS server, i.e. status is always disconnected.
I have collected the Tomcat (EPASSoap00010.log and security00010.log) logs via RTMT and compared them to the logs from the PCAP plugin. The relevant time period is from 15:14 to 15:17. In the Tomcat logs I can see that the authentication is successful (see attached files), however in the log of PCAP plugin I can see the following messages:
2012/02/03 15:14:35.281 WARNUNG Credential is rejected. Nothing to retry ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.answerChallenge() ::thread=CT_CALLBACK.1 ::loggername=com.cisco.sametime.phonestatus.cup
2012/02/03 15:14:35.281 WARNUNG #### Connection rejected presence server ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.onPresenceServerConnectionRejected() ::thread=CT_CALLBACK.1 ::loggername=com.cisco.sametime.phonestatus.cup
2012/02/03 15:14:35.281 WARNUNG Credential is rejected. Nothing to retry ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.answerChallenge() ::thread=CT_CALLBACK.2 ::loggername=com.cisco.sametime.phonestatus.cup
2012/02/03 15:14:35.281 WARNUNG #### Connection rejected presence server ::class.method=com.cisco.sametime.phonestatus.cup.CUPPresenceWatcher.onPresenceServerConnectionRejected() ::thread=CT_CALLBACK.2 ::loggername=com.cisco.sametime.phonestatus.cup
I don't understand why the connection is rejected although the Sametime Internal ID and CUPS User ID match. Does anyone know what the issue could be?
All posts are very much appreciated!
Thanks a lot in advance!
Kind regards,
Igor

Boot camp with Cisco VPN client and smart card

Looking at a Macbook or Macbook Air and the only reason I need to run windows is to be able to access my work network through the Cisco VPN client and my Smartcard then use remote desktop. From my understanding if I run Bootcamp it should work am I correct? Im going to an Apple store tomorrow hopefully they can help too.
Thanks

mrbacklash wrote:
Ok with that being said will the MBA 11.6 1.4ghz have the guts to make it run mostly internet based programs over the VPN connection?
I think if you are running apps over the Internet the bottleneck will be the Internet and your VPN bandwidth. Your computer can certainly execute faster than Internet communications.
Besides, Internet or remote applications run on the remote server. All your local computer does is local processing of the data if necessary.
Message was edited by: BobTheFisherman

Cisco VPN Client and Mac OS 10.5.1 update

After upgrading to Leopard (10.5) my Cisco VNP client stopped working. I was able to fix that by downloading the newer VPN Client 4.9.01 (0080) from the Macupdate.com website. Now that I've updated to Mac OS 10.5.1, the VPN Client won't work again!! I went back to the Macupdate website and downloaded what looks like an even newer version - 4.9.01 (0090) - but this is labeled as a BETA and it doesn't work either. Anyone out there seen a newer version, or something that works with 10.5.1?

b166er wrote:
Aside from the fact that it's marked beta, I'm wary about the source of MacUpdate's download. They link to http://www.arrange.co.at/download/vpnclient-darwin-4.9.01.0090-universal-k9-BETA .dmg
Cisco don't ever make the client freely available. The official download is via form on the Cisco web site and you need appropriate credentials. I wouldn't risk installing from any other source.
The home page at http://www.arrange.co.at/ doesn't exactly inspire confidence.
Dude has a point... it's risky to mess with something like this from an untrusted source IMHO. Cisco is picky about who they give it out to. I have to get mine through my host provider since they are the ones that are authorized.
For what it's worth, I'm using 4.9.01 with 10.5.1 and it works well.

What is the maximum number of PVC's supported by Cisco BPX 8620 and 8680 chassis with BCC-4V 128MB DRAM and 4 MB BRAM?

We are working on a capacity planning project for one of our customers and we need an estimate on the maximum number of PVCs supported in the following situations:
a)Cisco BPX 8620 and 8680 chassis with BCC-4V 128MB DRAM and 4 MB BRAM ?
b)Maximum number of PVC's supported by each of the following STM-1 cards:
- model BXM-155-4D and 4DX ?
- model BXM-155-8D and 8DX ?

a)It depends upon software level. b) 16,000 per card, With release 9.3:
60K Connections Support on BXM-E—Provides the ability to support a maximum of 60K per card for VSI applications for the BPX 8600, for example, PNNI or MPLS, used on enhanced BXM-E cards.

Problem with Cisco 861W router and outgoing VPN

We have a Cisco 861W router that is blocking an outgoing PPTP on the internal access point only. The outgoing VPN works when the traffic is through a wired connection or the connection is on another access point. We fail to make a connection only when connection to the 861W's internal Access Point.
Here is the Access Point Configuration:
Current configuration : 2100 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname obap
enable secret 5 $1$.1RF$go1D7WITXUn3s8TUaw3tC.
no aaa new-model
dot11 syslog
dot11 ssid OLIVER
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 0 XXXXXXXXXXX
username XXXXXX privilege 15 secret 5 $1$Wc0K$OzcQDDQfjHP6La31eXMoG/
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid OLIVER
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecti
ng AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.2 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
banner login ^CC
% Password change notice.
Default username/password setup on AP is cisco/cisco with priv¾ilege level 15.
It is strongly suggested that you create a new username with privilege level
15 using the following command for console security.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want to
use. After you change your username/password you can turn off this message
by configuring "no banner login" and "no banner exec" in privileged mode.
^C
line con 0
privilege level 15
login local
no activation-character
line vty 0 4
login local
cns dhcp
end
obap#
Here is the Router's Configuration:
Current configuration : 5908 bytes
! No configuration change since last restart
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname obrouter
boot-start-marker
boot-end-marker
logging buffered 51200
logging console critical
enable secret 5 $1$i9XE$DjxFVAEC9nC4/r6EQKCd6/
no aaa new-model
memory-size iomem 10
clock timezone PCTime -5
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
crypto pki trustpoint TP-self-signed-1856757619
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1856757619
revocation-check none
rsakeypair TP-self-signed-1856757619
crypto pki certificate chain TP-self-signed-1856757619
certificate self-signed 01
3082024D 308201B6 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31383536 37353736 3139301E 170D3036 30313032 31323030
34345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 38353637
35373631 3930819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B1A4 FB786547 3D582260 03DB768D 116BDE9A 309FBA04 B53F77B0 BFE32344
7C3439B3 97192B36 760A9411 1D5C7549 8D86F532 ABA44F53 0D08B7F4 A9A747D5
071330C3 65BF25A8 927F3596 29BB5A80 90C8D169 22268476 3B8DDE1E FDB7170D
B4820D03 5580A849 A92C7E76 9AC10867 505A2FEE 64360741 7F9DBDBF 3D79982C
F81D0203 010001A3 75307330 0F060355 1D130101 FF040530 030101FF 30200603
551D1104 19301782 156F6272 6F757465 722E6272 75736868 6F672E63 6F6D301F
0603551D 23041830 168014D8 5BC2FFB2 967A4C7B 11B44122 5C8D31F7 749B9230
1D060355 1D0E0416 0414D85B C2FFB296 7A4C7B11 B441225C 8D31F774 9B92300D
06092A86 4886F70D 01010405 00038181 005901F1 C239074B B8213567 CF7B65BF
DAFE4557 69B2A3B1 5F2593C7 A54B9598 23FD5E7A 563AA6E0 AFB25801 FA0061E8
F9545372 DB600B3A BE68AE65 1EDA593E 6A0C96B8 5A4136AF 393F9AAC 651E1C36
B8B7C6C0 47936C24 D2ECE9A5 9446EE32 FC7461FA AD8CF1CE A7FBF341 07E9C3C6
505AB88D 0E7FCAFC 5792298A E5E4D1FE CC
        quit
no ip source-route
ip dhcp excluded-address 192.168.0.1 192.168.0.99
ip dhcp pool ccp-pool1
   import all
   network 192.168.0.0 255.255.255.0
   dns-server 216.49.160.10 216.49.160.66
   default-router 192.168.0.1
ip cef
no ip bootp server
ip domain name brushhog.com
ip name-server 216.49.160.10
ip name-server 216.49.160.66
license udi pid CISCO861W-GN-A-K9 sn FTX155281FY
username tech38 privilege 15 secret 5 $1$d/4Z$n/23EsXbzfHF5XfJ8Nv.y0
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description $ES_WAN$$FW_OUTSIDE$
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
duplex auto
speed auto
pppoe-client dial-pool-number 1
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 192.168.0.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1412
interface Dialer0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip flow ingress
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname XXXXXXXXXXXXX
ppp chap password 7 XXXXXXXXXXXXXXXX
ppp pap sent-username XXXXXXXXXXXXXX password 7 XXXXXXXXXXX
no cdp enable
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source static tcp 192.168.0.25 80 interface Dialer0 80
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 192.168.0.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
line con 0
login local
no modem enable
transport output telnet
line aux 0
login local
transport output telnet
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
privilege level 15
login local
transport input telnet ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
Any help would be appreciated

Hello,
i have the same problem with router CISCO861W-GN-E-K9. Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Can someone help?
Thank you.
Here is my config for internal AP and router.

Cisco Works Polling and threshold

Similar Messages

Maybe you are looking for