Clustre verification failed for 10gR2 on RHEL3 Update 6
When i run this command (for Release1):
runcluvfy.sh comp sys -n node1,node2-p crs -r 10gR1 -osdba dba -orainv oinstall -verbose
It shows success.
But when i run (for Release2):
runcluvfy.sh comp sys -n node1,node2-p crs -r 10gR2 -osdba dba -orainv oinstall -verbose
It fails with
System requirement failed for 'crs'
Verification of system requirement was unsuccessful on all the nodes.
The package on which it fails is
Check: Package existence for "libpng-10-1.0.13-8"
Node Name Status Comment
node1 libpng-1.2.2-25 failed
node2 libpng-1.2.2-25 failed
Result: Package existence check failed for "libpng-10-1.0.13-8".
Initially when i ran CVU for nodeconnection check it failed and i continued due to the following message at metalink.
runcluvfy.sh comp ssa -n node1,node2verbose
CVU reports the error below if non-routable IP addresses such as 192.168.*.*, 172.*.*.* or 10.*.*.* are used for the public interface (eth0).
ERROR:
Could not find a suitable set of interfaces for VIPs.
Node connectivity check failed.
The error can be safely ignored. As a workaround, invoke the Virtual IP Configuration Assistant (VIPCA) manually during the installation on the second node and a suitable network interface (eth0) will be detected.
So is it the cause of this failed test or the libpng package problem ???
Thanks in Advance
Sujan Gautam
When you say Failed Explain!::: Do you mean when you go to About Phone then System Update it is Not Updating or what. If this is the Case it can Take a few Days from when the Update is Re-leased to Move around. You can help your Razr to get it by Turning it Off an then Back on. Once or twice Threw the Day to help try to Push it on it. I have done this with my Phones in the Past to Help push the Update on it. But as i said it may take a Few Days before you get it,,,b33
Similar Messages
-
Connection verification failed for data source using mySQL
Hi,
I having problem with mySQL datasource and getting the above error. This is only happening in our staging server. We are using ColdFusion 8 running JRUN4 and trying to connect to mySQL v 5.1.41. I tried adding DSN from my localhost using ColdFusion 9 developer edition and I am able to connect without error.I know that mysql server, username & password is valid. I can access the mysql also using mySQL gui tool from different pc and it works fine. I'm believe that this has something to do with mySQL driver? Can somebody shed some light on how can I fix my DSN connection problem? Thank you.
here's the error:
Connection verification failed for data source: forum
com.mysql.jdbc.CommunicationsException: Communications link failure due to underlying exception: ** BEGIN NESTED EXCEPTION ** java.net.ConnectException MESSAGE: Connection timed out: connect STACKTRACE: java.net.ConnectException: Connection timed out: connect at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) at java.net.Socket.connect(Socket.java:519) at java.net.Socket.connect(Socket.java:469) at java.net.Socket.(Socket.java:366) at java.net.Socket.(Socket.java:208) at com.mysql.jdbc.StandardSocketFactory.connect(StandardSocketFactory.java:173) at com.mysql.jdbc.MysqlIO.(MysqlIO.java:267) at com.mysql.jdbc.Connection.createNewIO(Connection.java:2739) at com.mysql.jdbc.Connection.(Connection.java:1553) at com.mysql.jdbc.NonRegisteringDriver.connect(NonRegisteringDriver.java:266) at coldfusion.server.j2ee.sql.pool.JDBCPool.createPhysicalConnection(JDBCPool.java:589) at coldfusion.server.j2ee.sql.pool.ConnectionRunner$RunnableConnection.run(ConnectionRunner. java:67) at java.lang.Thread.run(Thread.java:619) ** END NESTED EXCEPTION ** Last packet sent to the server was 0 ms ago.http://www.adobe.com/cfusion/knowledgebase/index.cfm?id=6ef0253
HTH
Tim Carley
www.recfusion.com
[email protected] -
Connection verification failed for data source:
Hi,
I having problem with mySQL datasource and getting the above error. This is only happening in our staging server. We are using ColdFusion 8 running JRUN4 and trying to connect to mySQL v 5.1.41. I tried adding DSN from my localhost using ColdFusion 9 developer edition and I am able to connect without error.I know that mysql server, username & password is valid. I can access the mysql also using mySQL gui tool from different pc and it works fine. I'm believe that this has something to do with mySQL driver? Can somebody shed some light on how can I fix my DSN connection problem? Thank you.
here's the error:
Connection verification failed for data source: forum
com.mysql.jdbc.CommunicationsException: Communications link failure due to underlying exception: ** BEGIN NESTED EXCEPTION ** java.net.ConnectException MESSAGE: Connection timed out: connect STACKTRACE: java.net.ConnectException: Connection timed out: connect at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) at java.net.Socket.connect(Socket.java:519) at java.net.Socket.connect(Socket.java:469) at java.net.Socket.(Socket.java:366) at java.net.Socket.(Socket.java:208) at com.mysql.jdbc.StandardSocketFactory.connect(StandardSocketFactory.java:173) at com.mysql.jdbc.MysqlIO.(MysqlIO.java:267) at com.mysql.jdbc.Connection.createNewIO(Connection.java:2739) at com.mysql.jdbc.Connection.(Connection.java:1553) at com.mysql.jdbc.NonRegisteringDriver.connect(NonRegisteringDriver.java:266) at coldfusion.server.j2ee.sql.pool.JDBCPool.createPhysicalConnection(JDBCPool.java :589) at coldfusion.server.j2ee.sql.pool.ConnectionRunner$RunnableConnection.run(Connect ionRunner.java:67) at java.lang.Thread.run(Thread.java:619) ** END NESTED EXCEPTION ** Last packet sent to the server was 0 ms ago.Also make sure your firewall has the required port open (1433
default) and if you are running 2003 on the SQL box, especially if
you ran the security Wizard, make sure the IPSec is allowing the CF
box to communicate with it, and vise verse. -
Verification failed for: Property Template Resource: The template specified
Hi All,
we are using Property Propagation report, but it is giving following message:
Verification failed for: Property Template Resource: The template specified does not exist
Regards,
GangaHi All,
issue is reolved. We should not give '%20' as indicator of Space.
that was the mistacke.
Regards,
Ganga -
Hostname Verification failed for certificate with CommonName 'gawlsdev02.ss
Hi All,
I want to know the meaning and the reason of this exception:
<Jun 17, 2010 2:05:52 PM EDT> <Warning> <Security> <BEA-090504> <Certificate chain received from gawlsdev02 - 147.141.83.104 failed
hostname verification check. Certificate contained gawlsdev02.ssga.statestr.com but check expected gawlsdev02>
<Jun 17, 2010 2:05:52 PM EDT> <Debug> <TLS> <000000> <Hostname Verification failed for certificate with CommonName 'gawlsdev02.ssga.
statestr.com' against hostname: gawlsdev02>
thanks in advance.When Webloigic Server tries to validate the certificate, it compares te CN of the certificate with the hostname from where the request is coming from.
If they don't match, hostname verfication fails and SSL connection is not established.
In your case I see the CN is gawlsdev02.ssga.statestr.com whereas WLS is expecting it to be gawlsdev02.
U can use this option to ignore host name verification
-Dweblogic.security.SSL.ignoreHostnameVerification=true
To know about other SSL issues, u can refer this
http://weblogic-wonders.com/weblogic/2010/01/28/troubleshooting-ssl-issues/
-Faisal -
Connection verification failed for data source on port 1433
Trying to set up a DSN for a SQL Server database on a new computer and it's failing every time.
Connection verification failed for data source: csf
java.sql.SQLNonTransientConnectionException: [Macromedia][SQLServer JDBC Driver]Error establishing socket to host and port: SANDYPC:1433. Reason: Connection refused: connect
The root cause was that: java.sql.SQLNonTransientConnectionException: [Macromedia][SQLServer JDBC Driver]Error establishing socket to host and port: SANDYPC:1433. Reason: Connection refused: connect
Now, when I installed CF 11, it installed on port 8500. However, when I try changing the port in the setup to 8500, I get this error:
Connection verification failed for data source: csf
java.sql.SQLException: Timed out trying to establish connection
The root cause was that: java.sql.SQLException: Timed out trying to establish connection
I cannot find anything online on how to fix this! HELP!!!Hi,
Is that SQL Express edition? If so perhaps TCP protocol is not enabled. Is Windows firewall turned on? Check port 1433 is open.
Normally you would not create a datasource to apache port 8500, that is a web server not database server port.
HTH, Carl. -
Signature verification failed for PolicyAssignmentID
I am in the process of setting up a new SCCM 2012 R2 server. I have just begun to add some test boxes to the environment and every server thus far is registering in SCCM but is not pulling down its policies. When doing a policy retrieval evaluation
cycle the below is
immediately spit out in the PolicyAgent.log file. Any help would be
appreciated!
Signature verification failed for PolicyAssignmentID {XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX}
Raising event:
instance of CCM_PolicyAgent_PolicyAuthorizationFailure
ClientID = "GUID:F504615C-04F8-462D-B341-265C2FAEE7E7";
DateTime = "20140708132926.819000+000";
PolicyNamespace = "\\\\.\\ROOT\\ccm\\policy\\Machine\\RequestedConfig";
PolicySource = "SMS:RET";
ProcessID = 3532;
ThreadID = 4320;It seems I have resolved my issue. The cause was in the AD publishing. I'm not sure if some parts were corrupt or simply missing but after removing the AD forest from 'Administration\Hierarchy Configuration\Active Directory Forests' in the
SCCM admin console and re-adding it back SCCM was able to republish the needed info. Then after a few minutes to allow for replication I was able to run a machine policy cycle which pulled all of my policies down! -
Verification Fails for Software Update AND files downloaded from Apple
Hi all,
Upon first running software update on my brand new MacBook Pro 15", I remember seeing that the verification of a couple downloads failed. After restarting repeatedly and running software update again and again, I eventually narrowed the culprit down to an iPhoto update image.
Bizarrely, even downloading the .dmg from the Apple Downloads site, in multiple browsers, would result in a failed verification. Yet downloading on other machines worked fine.
Now, I'm having trouble verifying the checksum of the iWork image from Apple's own site. I haven't the first clue about what's happening here.
Does anyone have even the faintest idea?
Thanks!try if booting your Mac into _*safe mode*_ helps. while in safe mode, repair permissions using disk utility, then reboot normally.
if the .dmg mounts on one of your other Macs, you can use your network to install the software. mount the .dmg on the other Mac and connect to it from the problem machine.
JGG -
Linking phase fails for 10gR2 on Ubuntu 6.06: undefined ref to 'nnfyboot'
I'm trying to install Oracle10gR2 on Ubuntu 6.06. The installation goes fine up to the linking phase where the installer reports 86% completion.
In linking phase i get the following error message dialog from OUI:
Error in invoking target 'utilities ctx_on' of makefile '/opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/rdbms/lib/ins_rdbms.mk'. See '/opt/oracle10g/u01/app/oraInventory/logs/installActions2006-08-12_11-54-03PM.log' for details.
The failing link command gives with the below error message:
% cd /opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/rdbms/lib
% make -f ins_rdbms.mk utilities ctx_on
- Linking tg4pwd utility
rm -f /opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/rdbms/lib/tg4pwd
gcc -o /opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/rdbms/lib/tg4pwd -L/opt/oracle10g
/u01/app/oracle/product/10.2.0/db_1/rdbms/lib/ -L/opt/oracle10g/u01/app/oracle/product/10.
2.0/db_1/lib/ -L/opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/lib/stubs/ -L/usr/lib -l
irc /opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/rdbms/lib/tg4pwd.o /opt/orac
le10g/u01/app/oracle/product/10.2.0/db_1/rdbms/lib/defopt.o /opt/oracle10g/u01/app/oracle
/product/10.2.0/db_1/rdbms/lib/homts.o -lagtsh -lpls10 -lplp10 -lclntsh -lsn
ls10 -lnls10 -lcore10 -lsnls10 -lnls10 -lcore10 -lsnls10 -lnls10 -lxml10 -lcore10 -lunls1
0 -lsnls10 -lnls10 -lcore10 -lnls10 /opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/lib/
libgeneric10.a `cat /opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/lib/sysliblist` -W
l,-rpath,/opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/lib -lm `cat /opt/oracle10g/
u01/app/oracle/product/10.2.0/db_1/lib/sysliblist` -ldl -lm -L/opt/oracle10g/u01/app/ora
cle/product/10.2.0/db_1/lib -lvsn10
/opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/lib//libagtsh.so: undefined reference to
`nnfyboot'
collect2: ld returned 1 exit status
make: *** [opt/oracle10g/u01/app/oracle/product/10.2.0/db_1/rdbms/lib/tg4pwd] Error 1
Any ideas on how to fix this issue? Has anyone else managed to install 10gR2 on Ubuntu 6.06?
Which library contains the nnfyboot symbol?hi
please find the installation given below
===========================================================
Download the following software:
Enterprise Manager Downloads
For convenience you may want to download the agent distribution separately. If you are monitoring servers on different platforms the relevant agents must be downloaded.
Unpack Files
First unzip the grid control installation files:
unzip Linux_Grid_Control_full_102010_disk1.zip
unzip Linux_Grid_Control_full_102010_disk2.zip
unzip Linux_Grid_Control_full_102010_disk3.zip
Hosts File
The /etc/hosts file must contain a fully qualified name for the server:
<IP-address> <fully-qualified-machine-name> <machine-name>
Set Kernel Parameters
Modify the /etc/sysctl.conf file to include the lines appropriate to your operating system:
# Red Hat Enterprise Linux 3.0 and CentOS 3.x
kernel.shmmax = 2147483648
kernel.shmmni = 4096
kernel.shmall = 2097152
kernel.shmmin = 1
kernel.shmseg = 10
# semaphores: semmsl, semmns, semopm, semmni
kernel.sem = 250 32000 100 128
fs.file-max = 65536
# Red Hat Enterprise Linux 4.0 and CentOS 4.x
kernel.shmmax = 536870912
kernel.shmmni = 4096
kernel.shmall = 2097152
# semaphores: semmsl, semmns, semopm, semmni
kernel.sem = 250 32000 100 128
fs.file-max = 65536
net.ipv4.ip_local_port_range = 1024 65000
net.core.rmem_default=262144
net.core.rmem_max=262144
net.core.wmem_default=262144
net.core.wmem_max=262144
Run the following command to change the current kernel parameters:
/sbin/sysctl -p
Disable secure linux by editing the /etc/selinux/config file, making sure the SELINUX flag is set as follows:
SELINUX=disabled
Alternatively, this alteration can be done using the GUI tool (Applications > System Settings > Security Level). Click on the SELinux tab and disable the feature.
Setup
The documentation states that the following packages are required by the relevant operating systems:
# Red Hat Enterprise Linux 3.0 and CentOS 3.x
glibc-2.2.4-31.7
make-3.79
binutils-2.11.90.0.8-12
gcc-2.96
openmotif21-2.1.30-11
# Red Hat Enterprise Linux 4.0 and CentOS 4.x
glibc-2.3.4-2.9
make-3.79
binutils-2.15.92.0.2-13
gcc-3.4.3-22.1
libaio-0.3.96
glibc-common-2.3.4-2.9
setarch-1.6-1
pdksh-5.2.14-30
openmotif21-2.1.30-11
sysstat-5.0.5-1
gnome-libs-1.4.1.2.90-44.1
libstdc++-3.4.3-22.1
libstdc++devel-3.4.3-22.1
compat-libstdc++-296-2.96-132.7.2
compat-db-4.1.25-9
control-center-2.8.0-12
xscreensaver-4.18-5.rhel4.2
Depending on the update/respin version of Red Hat or CentOS, the exact package versions and locations may vary. The installation of the required packages is shown below, with the versions and locations relevant for CentOS 4.1. The commented packages represent those that are already loaded.
# From CentOS 4.1 Disk 1
cd /media/cdrom/CentOS/RPMS
#rpm -Uvh glibc-2.3.4-2.9.i386.rpm
#rpm -Uvh glibc-common-2.3.4-2.9.i386.rpm
#rpm -Uvh make-3.80-5.i386.rpm
#rpm -Uvh binutils-2.15.92.0.2-13.i386.rpm
#rpm -Uvh setarch-1.6-1.i386.rpm
#rpm -Uvh pdksh-5.2.14-30.i386.rpm
#rpm -Uvh libstdc++-3.4.3-22.1.i386.rpm
rpm -Uvh compat-libstdc++-33-3.2.3-47.3.i386.rpm
# From CentOS 4.1 Disk 2
cd /media/cdrom/CentOS/RPMS
#rpm -Uvh gcc-3.4.3-22.1.i386.rpm
#rpm -Uvh gnome-libs-1.4.1.2.90-44.1.i386.rpm
#rpm -Uvh libstdc++-devel-3.4.3-22.1.i386.rpm
#rpm -Uvh compat-db-4.1.25-9.i386.rpm
#rpm -Uvh control-center-2.8.0-12.i386.rpm
#rpm -Uvh xscreensaver-4.18-5.rhel4.2.i386.rpm
# From CentOS 4.1 Disk 3
cd /media/cdrom/CentOS/RPMS
rpm -Uvh libaio-0.3.103-3.i386.rpm
rpm -Uvh openmotif21-2.1.30-11.RHEL4.4.i386.rpm
rpm -Uvh sysstat-5.0.5-1.i386.rpm
rpm -Uvh compat-libstdc++-296-2.96-132.7.2.i386.rpm
Create the new groups and users:
groupadd oinstall
groupadd dba
groupadd oper
useradd -g oinstall -G dba -s /bin/ksh oracle
passwd oracle
Create the directories in which the Oracle software will be installed:
mkdir -p /u01/app/oracle/product/10.2.0/oms10g
mkdir -p /u01/app/oracle/product/10.2.0/db10g
mkdir -p /u01/app/oracle/product/10.2.0/agent10g
chown -R oracle:oinstall /u01
Login as root and issue the following command:
xhost +<machine-name>
Login as the oracle user and add the following lines at the end of the .profile file:
# Oracle Settings
TMP=/tmp; export TMP
TMPDIR=$TMP; export TMPDIR
ORACLE_BASE=/u01/app/oracle; export ORACLE_BASE
ORACLE_HOME=$ORACLE_BASE/product/10.2.0/db10g; export ORACLE_HOME
ORACLE_SID=emrep; export ORACLE_SID
PATH=.:/usr/sbin:#$ORACLE_HOME/bin:$PATH; export PATH
PATH=$PATH:$ORACLE_HOME/dcm/bin:$ORACLE_HOME/opmn/bin; export PATH
PATH=$PATH:$ORACLE_HOME/Apache/Apache/bin; export PATH
PS1="`hostname`> "
set -o emacs
set filec
Grid Control Installation
Log into the oracle user. If you are using X emulation then set the DISPLAY environmental variable:
DISPLAY=<machine-name>:0.0; export DISPLAY
Start the Oracle Universal Installer (OUI) by issuing the following command in the installation software directory:
./runInstaller
During the installation select the appropriate ORACLE_HOME for the grid control (oms) and select the new database option. The installation will automatically install an agent in the agent home -
Download Failed for 2.3.4 update
When I check for new updates, I am told that one is available. However, when I click "OK" I receive a message that says "Error: Download Failed". Anyone else seeing this? Anyone know how to correct it? I really don't want to go through a factory reset!
KratosWith no help from Verizon as they just told me over the phone to do a factory reset, I finally found a solution to this issue!
Check out this information: http://androidforums.com/htc-droid-incredible-2/418849-solution-2-3-4-download-failed.html
It worked for me and at least two other people!
Kratos -
I need a little help, what have I done wrong or not done?
Here is the error message that is returned;
Connection verification failed for data source: Archuleta_xxxxxx
java.sql.SQLException: Timed out trying to establish connection
The root cause was that: java.sql.SQLException: Timed out trying to establish connection
any ideas would be appreciated.I see this error in your output:
2014-11-26 10:55:23,583 ERROR [ThemeAutoDeployer]
java.io.FileNotFoundException: /tmp/liferay/com/liferay/portal/deploy/dependencies/liferay-theme.tld (Too many open files)
I'm not across what the EBS recommended setting for this is, or if there is one. But try running:
ulimit -n
... and if the number is low, edit /etc/security/limits.conf , add some entries for increased "soft nofile" and "hard nofile" and run sysctl -p. See Linux & Java tips: Too many open files . -
Hi all,
I've been seeing a really weird problem with signing my HTML5 extension for Illustrator. I'm using the ZXPSignCmd tool to create a .zxp bundle and sign my extension from the command line. I'm able to install the extension using the Extension Manager, and I've also been able to distribute it to a private group through Adobe Exchange. It installs just fine, and runs great the first time, but after closing Illustrator and reopening it the extension often fails to load and just shows a blank window. I'm on a Mac, and looking at the log file here shows the following error when it happens:
/Users/<<userName>>/Library/Logs/CSXS/csxs-ILST.log
2014-12-17 10:18:02 : ERROR Signature verification failed for <<extensionID>>
This is the only indication I have that it is a problem with the certificate. It seems really strange that it installs without errors and works once, but then fails when trying to load again. I was using a self-signed certificate, but I just bought a certificate from DigiCert to see if that would help, but I'm still having the same problem.
This actually happens very rarely on my machine, but happens frequently to my other users. I assume this is somehow because I have been doing the development on this computer, so something is different about my extension environment.
Has anyone else seen this issue at all? Does anyone have any tips that might help me to debug this? Other log files to look at, potential problems with the certificate or manifest file? I've tried about everything I could think of, so any help would be greatly appreciated!
Thanks,
JamesNailed :-)
For the folder you might save files into, there are few tokens in CEP:
/* Identifies the path to user data. */
SystemPath.USER_DATA = "userData";
/* Identifies the path to common files for Adobe applications. */
SystemPath.COMMON_FILES = "commonFiles";
/* Identifies the path to the user's default document folder. */
SystemPath.MY_DOCUMENTS = "myDocuments";
/* Identifies the path to current extension. */
/* DEPRECATED, PLEASE USE EXTENSION INSTEAD. */
SystemPath.APPLICATION = "application";
/* Identifies the path to current extension. */
SystemPath.EXTENSION = "extension";
/* Identifies the path to hosting application's executable. */
SystemPath.HOST_APPLICATION = "hostApplication";
Otherwise you can rely on JSX folder tokens such as Folder.appData, Folder.userData etc (see a complete list on pages 56-57 of the JavaScript Tools Guide pdf) and create your extension's own folder.
Mind you, CEP extensions should support both indexedDB and localStorage - one of them might fit your needs.
Best
Davide Barranca
www.davidebarranca.com
www.cs-extensions.com -
550 Sender Verification Failed
I am having trouble sending mail to some hosts.
Can someone tell me how to allow sender verification?
I'm on a fresh install of 10.5.8 Server.
I believe my DNS is set up correctly and it has been well over 48 hours...
the "sa" user has mail enabled in WGM.
"This is the mail system at host server.agicrossmedia.com.
I'm sorry to have to inform you that your message could not
be delivered to one or more recipients. It's attached below.
For further assistance, please send mail to postmaster.
If you do so, please include this problem report. You can
delete your own text from the attached returned message.
The mail system
<[email protected]>: host anotherhost.com[74.86.169.89] said:
550-Verification failed for <[email protected]> 550-Previous (cached)
callout verification failure 550 Sender verify failed (in reply to RCPT TO
command)"I'm still getting the same problem after correcting the mx issue (now only 1 mx record for mail.agicrossmedia.com)
Also correction the reverse DNS issue.
Do you know of any other things I could check?
<[email protected]>: host yellowcurve.com[74.86.169.89] said:
550-Verification failed for <[email protected]> 550-Previous (cached)
callout verification failure 550 Sender verify failed (in reply to RCPT TO
command)
Message was edited by: RGNelson -
XML Signature Verification Failing.... Need help
Hi,
I am trying to do signing and encryption at our side and try to decrypt and verify the sign at destination side.
Here i succeeded with signing, encryption and decryption. but failing at verification part. Can any body help me finding what mistake iam doing ?
Here i am copying the encrypted data from one server and giving input to other server to decrypt and verify sign.
Any help is greatly appreciated
Here is the log :
I am not requested to follow nested Manifests
2005-07-20 18:34:34,546 DEBUG [Thread-593] [org.apache.xml.security.utils.ElementProxy] [] setElement("ds:Reference", "thismessage:/")
2005-07-20 18:34:34,546 DEBUG [Thread-593] [org.apache.xml.security.utils.Base64] [] I was asked to decode "hfHBf9N+SL3lU9Tz8qYcR5Gz48E="
2005-07-20 18:34:34,546 DEBUG [Thread-593] [org.apache.xml.security.utils.resolver.ResourceResolver] [] I was asked to create a ResourceResolver and got 0
2005-07-20 18:34:34,546 DEBUG [Thread-593] [org.apache.xml.security.utils.resolver.ResourceResolver] [] extra resolvers to my existing 5 system-wide resolvers
2005-07-20 18:34:34,609 DEBUG [Thread-593] [org.apache.xml.security.utils.resolver.ResourceResolver] [] check resolvability by class org.apache.xml.security.utils.resolver.implementations.ResolverDirectHTTP
2005-07-20 18:34:34,609 DEBUG [Thread-593] [org.apache.xml.security.utils.resolver.ResourceResolver] [] check resolvability by class org.apache.xml.security.utils.resolver.implementations.ResolverLocalFilesystem
2005-07-20 18:34:34,609 DEBUG [Thread-593] [org.apache.xml.security.utils.resolver.ResourceResolver] [] check resolvability by class org.apache.xml.security.utils.resolver.implementations.ResolverFragment
2005-07-20 18:34:34,937 DEBUG [Thread-593] [org.apache.xml.security.utils.ElementProxy] [] setElement("ds:Transforms", "thismessage:/")
2005-07-20 18:34:34,968 DEBUG [Thread-593] [org.apache.xml.security.utils.ElementProxy] [] setElement("ds:Transform", "thismessage:/")
2005-07-20 18:34:34,968 DEBUG [Thread-593] [org.apache.xml.security.transforms.Transforms] [] Preform the (0)th http://www.w3.org/TR/2001/REC-xml-c14n-20010315 transform
2005-07-20 18:34:35,000 DEBUG [Thread-593] [org.apache.xml.security.algorithms.JCEMapper] [] Request for URI http://www.w3.org/2000/09/xmldsig#sha1
2005-07-20 18:34:35,015 DEBUG [Thread-593] [org.apache.xml.security.algorithms.JCEMapper] [] Found SHA-1 from provider BC
2005-07-20 18:34:35,078 DEBUG [Thread-593] [org.apache.xml.security.signature.Reference] [] <OrderCreate Version ...
2005-07-20 18:34:35,078 WARN [Thread-593] [org.apache.xml.security.signature.Reference] [] Verification failed for URI ""
2005-07-20 18:34:35,078 DEBUG [Thread-593] [org.apache.xml.security.signature.Reference] [] unverifiedDigestValue= hfHBf9N+SL3lU9Tz8qYcR5Gz48E=
2005-07-20 18:34:35,078 DEBUG [Thread-593] [org.apache.xml.security.signature.Reference] [] calculatedDigestValue= XBKGSvU5kiErHoBXSEeqJ8JUgZU=
2005-07-20 18:34:35,078 DEBUG [Thread-593] [org.apache.xml.security.signature.Manifest] [] The Reference has Type
2005-07-20 18:34:35,078 INFO [Thread-593] Signature Validation Result ----------- = false
Thanks in Advance.
-AnamSHi got the problem. Its rectified.
-Surendra -
Zypper "Digest verification failed"
Hi,
when installing oes11sp2-December-2014-Hot-Patch I get a "Digest
verification failed for novell-plugin-base-2.7.7-0.23.29.2.noarch.rpm". It's
the same on all my servers.
I guess this is a problem with the repo servers? Is Novell aware of this, or
which is the best way to inform them?
Thanks,
MirkoOn 18/12/2014 11:52, Mirko Guldner wrote:
> when installing oes11sp2-December-2014-Hot-Patch I get a "Digest
> verification failed for novell-plugin-base-2.7.7-0.23.29.2.noarch.rpm". It's
> the same on all my servers.
>
> I guess this is a problem with the repo servers? Is Novell aware of this, or
> which is the best way to inform them?
Novell are aware - see
https://forums.novell.com/showthread...nce-OES-11-SP1
It's a problem with the third-party EdgeCast's Content Delivery Network
(CDN).
HTH.
Simon
Novell Knowledge Partner
If you find this post helpful and are logged into the web interface,
please show your appreciation and click on the star below. Thanks.
Maybe you are looking for
-
How do I turn off Photoshop Elements Welcome Tour?
Everytime I start Photoshop Elements 8 I get stuck in an endless loop of the "Welcome to Photoshop Elements" screen. There is no close button or link. The only way I have found to get past it is by clicking on "Show me what is new", then "Start Tou
-
Get x and y coordinated from a text position in JtextComponent
Hi, I want to paint matching brackets in my JTextComponent. I have the position of the char I need to paint but in order to use paint() I need the x,y coordinates. Any idea? Dekel
-
Can Lr5 read Nikon D610 raw picture?
Hi, I downloaded Lr5 and installedt, but it can' t read Nikon D610 raw picture, why? hope for help, thanks!
-
Is there a way to put all of my music FROM the iPOD TO a computer?
-
Why wont itunes let me update my ipod touch 4g. to ios 5
itunes has a message pop up whenever i try to update saying it "could not be restored, an unknown error occured. (3194)". how do i fix this?