CMAK client VPN issues

Hi,
We have been using the "standard" XP/Windows VPN client with our ISA 2006 Enterprise server for years with no real issues. I've recently decided to start rolling out a new client using Connection Manager Administration Kit (CMAK) so we can efficiently
map/disconnect mapped drives. Tested with a small group of users and no problems at all. Have now rolled the client out to about 10% of our workforce and we are getting
intermittent VPN connectivity issues and I'm sure it's related to our new client. The Remote Access Service stops running and only way to start it up again is to restart our ISA 2006 server. Proxy and firewall services are still fine. 
VPN protocol on both old and new clients are PPP.
I've noticed the new client also has software compression enabled where as the old one does not. Could software compression cause this problem?

Hi,
Is there any error in Logging?
You could also check the blog below.
Using CMAK to Configure ISA Server VPN Clients
http://forum.persiannetworks.com/f80/t33486.html
Note: Microsoft provides third-party contact information to help you find technical support. This contact
information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Best Regards,
Joyce
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Similar Messages

  • OS X Server VPN and OS X Client VPN Kerberos issue

    I set up OS X Server Leopard at home. I configured VPN on the server. I opened all of the recommended ports and then some.
    I've added the OS X Server to Directory Utility on my OS X client. I've configured a System Preferences > Network > VPN for the connection. I set it up for L2TP using the external address for my server at home, my username in Open Directory, and selected Kerberos for authentication. When I try to connect with the OS X VPN client it asks me to authenticate to [email protected] not [email protected]
    Does anyone have any idea where I should look to see why my OS X Client VPN Client is not trying to authenticate me using Kerberos to my home server but rather choosing my home username and my work Open Directory server? I looked on the forums but I don't see anyone describing this problem with VPN and Kerberos.
    Thanks in advance

    Brandon Macinnis wrote:
    Dnar,
    Thanks for the follow up bit about using the smbutil statshares command.  I used that and could confirm that I am also able to force it to connect with smb2.  Oddly though, in the stat share info it still says "AUTO_NEGOTIATE"
                                  SMB_NEGOTIATE                 AUTO_NEGOTIATE
                                  SMB_VERSION                   SMB_2.1
    But maybe that just means something else and not the fact that it did not auto negotiate to SMB.  I guess for now this will be what I have to do to use smb2.
    I think in this case the AUTO_NEGOTIATE merely means it will auto negotiate a connection between SMB1, SMB2, and (from your data) also SMB2.1 this would have nothing to do with auto negotiating between SMB2 and AFP, which from this thread appears broken.
    I also would like to thank Brandon for the tip about smbutil statshares, I had been looking for a simple way to tell what version of SMB was being used to test my NAS.
    For everyone's benefit, it would appear from the above that whilst Apple advertise Mavericks as using SMB2 they have gone as far as implementing SMB2.1 and merely list it only as SMB2 for simplicity and due to the fact there is not a huge different between SMB2 and SMB2.1
    See http://en.wikipedia.org/wiki/Server_Message_Block#SMB_2_and_3

  • Any ideas how to better troubleshoot VPN issue?

    Hi,
    I've recently upgraded my WLAN router to a brand new AVM FRITZ!Box WLAN 7390, in part for its VPN capabilities.
    So far, I've been unable to create a working connection.
    AVM's VPN is based on Cisco IPSec, and they provide a step-by-step procedure on how configure a Mac-based VPN connection (http://www.avm.de/de/Service/Service-Portale/Service-Portal/VPN_Interoperabilita et/16206.php - unfortunately only available in German, sorry). Following it, I still can't get it to work. Contacting their support I got first the same procedure and after pointing out I already followed it a "we don't support other vendors".
    Funny enough, I got a second VPN connection to my work's VPN server just fine, though admittedly there we have a true Cisco box.
    My initial setup was based on a 192.x.x.x net on my AVM, I could establish a VPN connection but coudn't ping/ssh/http/you-name-the-protocol in either direction. Our companies net is a 10.x.x.x net so, and as I have also VMware fusion running on my Mac with DHCP enabled on a different 192.x.x.x net plus a third 192.x.x.x net from my Wifi access I decided to reconfigure my AVM net to a 172.x.x.x net and stop VMware services for the tests (ie simplify as much as I could to help troubleshoot).
    Alas, instead of being able to establish a non-working VPN connection, now I ain't able to get the tunnel up. IKE Phase 1 completes but Phase 2 doesn't.
    Here's the relevant section from kernel.log:
    Dec 30 11:47:57 jupiter configd[16]: IPSec connecting to server <myservernameismybusiness>.dyndns.info
    Dec 30 11:47:57 jupiter configd[16]: SCNC: start, triggered by SystemUIServer, type IPSec, status 0
    Dec 30 11:47:57 jupiter configd[16]: IPSec Phase1 starting.
    Dec 30 11:47:57 jupiter racoon[1910]: IPSec connecting to server 77.x.x.x
    Dec 30 11:47:57 jupiter racoon[1910]: Connecting.
    Dec 30 11:47:57 jupiter racoon[1910]: IPSec Phase1 started (Initiated by me).
    Dec 30 11:47:57 jupiter racoon[1910]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1).
    Dec 30 11:47:58 jupiter racoon[1910]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2).
    Dec 30 11:47:58 jupiter racoon[1910]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2).
    Dec 30 11:47:58 jupiter racoon[1910]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode).
    Dec 30 11:47:58 jupiter racoon[1910]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3).
    Dec 30 11:47:58 jupiter racoon[1910]: IKE Packet: transmit success. (Information message).
    Dec 30 11:47:58 jupiter racoon[1910]: IKEv1 Information-Notice: transmit success. (ISAKMP-SA).
    Dec 30 11:47:58 jupiter racoon[1910]: IPSec Phase1 established (Initiated by me).
    Dec 30 11:47:58 jupiter racoon[1910]: IPSec Extended Authentication requested.
    Dec 30 11:47:58 jupiter configd[16]: IPSec requesting Extended Authentication.
    Dec 30 11:48:01 jupiter configd[16]: IPSec sending Extended Authentication.
    Dec 30 11:48:01 jupiter racoon[1910]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 11:48:01 jupiter racoon[1910]: IPSec Extended Authentication sent.
    Dec 30 11:48:02 jupiter racoon[1910]: IKEv1 XAUTH: success. (XAUTH Status is OK).
    Dec 30 11:48:02 jupiter racoon[1910]: IPSec Extended Authentication Passed.
    Dec 30 11:48:02 jupiter racoon[1910]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 11:48:02 jupiter racoon[1910]: IKEv1 Config: retransmited. (Mode-Config retransmit).
    Dec 30 11:48:02 jupiter racoon[1910]: IPSec Network Configuration requested.
    Dec 30 11:48:03 jupiter racoon[1910]: IPSec Network Configuration established.
    Dec 30 11:48:03 jupiter racoon[1910]: IKE Packet: receive success. (MODE-Config).
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration started.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = 172.77.7.14.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration: SAVE-PASSWORD = 1.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration: DEFAULT-ROUTE = local-address 172.77.7.14/32.
    Dec 30 11:48:03 jupiter configd[16]: host_gateway: write routing socket failed, command 2, No such process
    Dec 30 11:48:03 jupiter configd[16]: IPSec Phase2 starting.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration established.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Phase1 established.
    Dec 30 11:48:03 jupiter configd[16]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.43.242), current interface setting (name: utun0, family: 1001, address: 172.77.7.14, subnet: 255.255.255.255, destination: 172.77.7.14).
    Dec 30 11:48:03 jupiter racoon[1910]: IPSec Phase2 started (Initiated by me).
    Dec 30 11:48:03 jupiter racoon[1910]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1).
    Dec 30 11:48:03 jupiter configd[16]: network configuration changed.
    Dec 30 11:48:03 jupiter configd[16]: IPSec port-mapping update for en1 ignored: VPN is the Primary interface. Public Address: ac4d070e, Protocol: None, Private Port: 0, Public Port: 0
    Dec 30 11:48:03 jupiter configd[16]:
    Dec 30 11:48:03 jupiter configd[16]: setting hostname to "jupiter.local"
    Dec 30 11:48:03 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:06 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:07 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:09 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:09 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:12 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:13 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:15 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:15 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:18 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:18 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:21 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:21 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:24 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:25 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:27 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:27 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:30 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:30 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:33 jupiter configd[16]: IPSec disconnecting from server 77.x.x.x
    Dec 30 11:48:33 jupiter racoon[1910]: IPSec disconnecting from server 77.x.x.x
    Dec 30 11:48:33 jupiter racoon[1910]: IKE Packet: transmit success. (Information message).
    Dec 30 11:48:33 jupiter racoon[1910]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA).
    Dec 30 11:48:33 jupiter configd[16]: SCNC Controller: service_ending_verify_primaryservice, waiting for PrimaryService. status = 1
    Dec 30 11:48:33 jupiter configd[16]:
    Dec 30 11:48:33 jupiter configd[16]: network configuration changed.
    Dec 30 11:48:33 jupiter configd[16]: SCNC Controller: ipv4_state_changed, done waiting for ServiceID.
    Dec 30 11:48:33 jupiter configd[16]:
    Dec 30 11:48:33 jupiter configd[16]: setting hostname to "jupiter"
    When connecting to my work-place it looks like:
    Dec 30 12:33:14 jupiter configd[16]: IPSec connecting to server <mycompanyismybusiness>.ch
    Dec 30 12:33:14 jupiter configd[16]: SCNC: start, triggered by SystemUIServer, type IPSec, status 0
    Dec 30 12:33:14 jupiter configd[16]: IPSec Phase1 starting.
    Dec 30 12:33:14 jupiter racoon[1976]: IPSec connecting to server 62.x.x.x
    Dec 30 12:33:14 jupiter racoon[1976]: Connecting.
    Dec 30 12:33:14 jupiter racoon[1976]: IPSec Phase1 started (Initiated by me).
    Dec 30 12:33:14 jupiter racoon[1976]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1).
    Dec 30 12:33:14 jupiter racoon[1976]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2).
    Dec 30 12:33:14 jupiter racoon[1976]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2).
    Dec 30 12:33:14 jupiter racoon[1976]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode).
    Dec 30 12:33:14 jupiter racoon[1976]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3).
    Dec 30 12:33:14 jupiter racoon[1976]: IPSec Phase1 established (Initiated by me).
    Dec 30 12:33:15 jupiter racoon[1976]: IPSec Extended Authentication requested.
    Dec 30 12:33:15 jupiter configd[16]: IPSec requesting Extended Authentication.
    Dec 30 12:33:21 jupiter configd[16]: IPSec sending Extended Authentication.
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Extended Authentication sent.
    Dec 30 12:33:21 jupiter racoon[1976]: IKEv1 XAUTH: success. (XAUTH Status is OK).
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Extended Authentication Passed.
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 12:33:21 jupiter racoon[1976]: IKEv1 Config: retransmited. (Mode-Config retransmit).
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Network Configuration requested.
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Network Configuration established.
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: receive success. (MODE-Config).
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration started.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = 10.100.1.18.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-MASK = 255.255.255.0.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: SAVE-PASSWORD = 1.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-DNS = 10.100.1.129.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: SPLIT-INCLUDE.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: DEF-DOMAIN = iw.local.
    Dec 30 12:33:21 jupiter configd[16]: host_gateway: write routing socket failed, command 2, No such process
    Dec 30 12:33:21 jupiter configd[16]: installed route: (address 10.100.1.0, gateway 10.100.1.18)
    Dec 30 12:33:21 jupiter configd[16]: IPSec Phase2 starting.
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Phase2 started (Initiated by me).
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1).
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration established.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Phase1 established.
    Dec 30 12:33:21 jupiter configd[16]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.43.242), current interface setting (name: utun0, family: 1001, address: 10.100.1.18, subnet: 255.255.255.0, destination: 10.100.1.18).
    Dec 30 12:33:21 jupiter configd[16]: network configuration changed.
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: receive success. (Initiator, Quick-Mode message 2).
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3).
    Dec 30 12:33:21 jupiter racoon[1976]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode).
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Phase2 established (Initiated by me).
    Dec 30 12:33:21 jupiter configd[16]: IPSec Phase2 established.
    An earlies test in a Starbucks around here had the same result, during looking at the netstat -nr output I found I got onto a 10.x.x.x net on the Wifi and still could connect to the (different) 10.x.x.x net at work.
    My TCP/IP Networking course was around 2000, but the default route seen in the non-working log section looks like bullsh*t to me anyhow: DEFAULT-ROUTE = local-address 172.77.7.14/32
    On the other hand, the Phase 2 message seem to indicate a different mode for Phase 2 between the working and the non-working one.
    This is from the exported config of my AVM box:
    **** CFGFILE:vpn.cfg
    * /var/flash/vpn.cfg
    * Wed Dec 28 16:01:09 2011
    vpncfg {
            connections {
                    enabled = yes;
                    conn_type = conntype_user;
                    name = "[email protected]";
                    always_renew = no;
                    reject_not_encrypted = no;
                    dont_filter_netbios = yes;
                    localip = 0.0.0.0;
                    local_virtualip = 0.0.0.0;
                    remoteip = 0.0.0.0;
                    remote_virtualip = 172.77.7.14;
                    remoteid {
                            key_id = "<mykeyismybusiness>";
                    mode = phase1_mode_aggressive;
                    phase1ss = "all/all/all";
                    keytype = connkeytype_pre_shared;
                    key = "<mykeyismybusiness>";
                    cert_do_server_auth = no;
                    use_nat_t = no;
                    use_xauth = yes;
                    xauth {
                            valid = yes;
                            username = "<myuserismybusiness>";
                            passwd = "<mypasswordismybusiness>";
                    use_cfgmode = no;
                    phase2localid {
                            ipnet {
                                    ipaddr = 0.0.0.0;
                                    mask = 0.0.0.0;
                    phase2remoteid {
                            ipaddr = 172.22.7.14;
                    phase2ss = "esp-all-all/ah-none/comp-all/no-pfs";
                    accesslist =
                                 "permit ip 172.22.7.0 255.255.255.240 172.22.7.14 255.255.255.255";
            ike_forward_rules = "udp 0.0.0.0:500 0.0.0.0:500",
                                "udp 0.0.0.0:4500 0.0.0.0:4500";
    // EOF
    **** END OF FILE ****
    I also noticed an extra "IPSec port-mapping update for en1 ignored" message in the non-working log section, but I'm not sure a) how significant that might be, and b) how to find out what the ignored update might have been to decide whether not ignoring it would help.
    A quick test with the AnyConnect Client from Cisco didn't help either, apparently it establishes an https connection first as I got a window which certificate details from my QNAP behind the AVM Box (I got a port forward for https to it)
    So I'm looking for any ideas how to better troubleshoot this VPN issue...
    Many thanks in advance!
    BR,
    Alex

    Ok, found a small typo in my config (had at one point a 172.77.7.14 instead of the 172.22.7.14), no I can also connect from the 172.x.x.x net but still no ping etc. The relevant section of the log looks now like this:
    Dec 30 16:44:27 jupiter configd[16]: IPSec connecting to server <myservernameismybusiness>.dyndns.info
    Dec 30 16:44:27 jupiter configd[16]: SCNC: start, triggered by SystemUIServer, type IPSec, status 0
    Dec 30 16:44:28 jupiter configd[16]: IPSec Phase1 starting.
    Dec 30 16:44:28 jupiter racoon[2183]: IPSec connecting to server 77.x.x.x
    Dec 30 16:44:28 jupiter racoon[2183]: Connecting.
    Dec 30 16:44:28 jupiter racoon[2183]: IPSec Phase1 started (Initiated by me).
    Dec 30 16:44:28 jupiter racoon[2183]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1).
    Dec 30 16:44:28 jupiter racoon[2183]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2).
    Dec 30 16:44:28 jupiter racoon[2183]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2).
    Dec 30 16:44:28 jupiter racoon[2183]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode).
    Dec 30 16:44:28 jupiter racoon[2183]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3).
    Dec 30 16:44:28 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:44:28 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (ISAKMP-SA).
    Dec 30 16:44:28 jupiter racoon[2183]: IPSec Phase1 established (Initiated by me).
    Dec 30 16:44:28 jupiter racoon[2183]: IPSec Extended Authentication requested.
    Dec 30 16:44:28 jupiter configd[16]: IPSec requesting Extended Authentication.
    Dec 30 16:44:31 jupiter configd[16]: IPSec sending Extended Authentication.
    Dec 30 16:44:31 jupiter racoon[2183]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 16:44:31 jupiter racoon[2183]: IPSec Extended Authentication sent.
    Dec 30 16:44:32 jupiter racoon[2183]: IKEv1 XAUTH: success. (XAUTH Status is OK).
    Dec 30 16:44:32 jupiter racoon[2183]: IPSec Extended Authentication Passed.
    Dec 30 16:44:32 jupiter racoon[2183]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 16:44:32 jupiter racoon[2183]: IKEv1 Config: retransmited. (Mode-Config retransmit).
    Dec 30 16:44:32 jupiter racoon[2183]: IPSec Network Configuration requested.
    Dec 30 16:44:33 jupiter racoon[2183]: IPSec Network Configuration established.
    Dec 30 16:44:33 jupiter racoon[2183]: IKE Packet: receive success. (MODE-Config).
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration started.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = 172.22.7.14.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration: SAVE-PASSWORD = 1.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-DNS = 172.22.7.1.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration: DEFAULT-ROUTE = local-address 172.22.7.14/32.
    Dec 30 16:44:33 jupiter configd[16]: host_gateway: write routing socket failed, command 2, No such process
    Dec 30 16:44:33 jupiter configd[16]: IPSec Phase2 starting.
    Dec 30 16:44:33 jupiter racoon[2183]: IPSec Phase2 started (Initiated by me).
    Dec 30 16:44:33 jupiter racoon[2183]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1).
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration established.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Phase1 established.
    Dec 30 16:44:33 jupiter configd[16]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.43.242), current interface setting (name: utun0, family: 1001, address: 172.22.7.14, subnet: 255.255.255.255, destination: 172.22.7.14).
    Dec 30 16:44:33 jupiter configd[16]: network configuration changed.
    Dec 30 16:44:33 jupiter racoon[2183]: IKE Packet: receive success. (Initiator, Quick-Mode message 2).
    Dec 30 16:44:33 jupiter racoon[2183]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3).
    Dec 30 16:44:33 jupiter racoon[2183]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode).
    Dec 30 16:44:33 jupiter racoon[2183]: IPSec Phase2 established (Initiated by me).
    Dec 30 16:44:33 jupiter configd[16]: IPSec Phase2 established.
    Dec 30 16:44:43 jupiter racoon[2183]: IKE Packet: receive failed. (MODE-Config).
    Dec 30 16:44:48 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:44:48 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:44:48 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:44:48 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:44:48 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:45:03 jupiter configd[16]: setting hostname to "jupiter.local"
    followed by lots of:
    Dec 30 16:45:03 jupiter racoon[2183]: IKE Packet: receive failed. (MODE-Config).
    Dec 30 16:45:08 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:45:08 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:45:08 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:45:08 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:45:08 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:45:28 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:45:28 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:45:28 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:45:29 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:45:29 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:45:49 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:45:49 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:45:49 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:45:50 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:45:50 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:46:10 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:46:10 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:46:10 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:46:10 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:46:10 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:46:30 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:46:30 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:46:30 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:46:30 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:46:30 jupiter racoon[2183]: IKE Packet: receive success. (Information message).

  • SAPGUI Java 7.20 Rev 6 download and VPN issue

    Dear SAP friends please help.
    We are trying to connect to SAP via a Mac running Lion and a VPN with SAPGUI for Java Rev 5. We get the logon successfully but never get further than the licence message. We have updated to the latest Java and also tried it in 32 bitz mode. We are unable to download the latest Rev 6 (due to my user authorisation) but we still think this is a VPN issue. Can you please help? I enclose the trace which shows the point at which is stops.
    Many thanks
    Andrew
    16.11. 17:36:05.118 CALL:     <CONTROL SHELLID="101">
    16.11. 17:36:05.118 CALL:       <PROPERTY VALUE="0" NAME="120"/>
    16.11. 17:36:05.118 CALL:       <PROPERTY VALUE="0" NAME="300"/>
    16.11. 17:36:05.118 CALL:     </CONTROL>
    16.11. 17:36:05.118 CALL:   </CONTROLS>
    16.11. 17:36:05.118 CALL:   <COPY id="copy">
    16.11. 17:36:05.118 CALL:     <GUI id="gui">
    16.11. 17:36:05.118 CALL:       <METRICS id="metrics" X3="1440" X2="7" X1="7" X0="283" Y3="900" Y2="20" Y1="12" Y0="283"/>
    16.11. 17:36:05.118 CALL:     </GUI>
    16.11. 17:36:05.118 CALL:   </COPY>
    16.11. 17:36:05.118 CALL: </DATAMANAGER>
    16.11. 17:36:05.119 CALL: Call 1042: #3#.setMoreDataIndicator(true);
    16.11. 17:36:05.122 CON: GuiNiNetConnection: sending DIAG data to writer thread for modus 0
    ERROR #############################
    16.11. 17:37:10.018 ERROR: GuiNiReaderThread: read failed: Error: connection to partner '172.23.200.109:3200' broken
    16.11. 17:37:10.018 ERROR: 
    16.11. 17:37:10.018 ERROR: Wed Nov 16 17:37:10 2011
    16.11. 17:37:10.018 ERROR: Release 720
    16.11. 17:37:10.018 ERROR: Component NI (network interface), version 40
    16.11. 17:37:10.018 ERROR: rc = -6, module nixxi.cpp, line 5087
    16.11. 17:37:10.018 ERROR: Detail NiIRead: P=172.23.200.109:3200; L=10.64.10.112:53387
    16.11. 17:37:10.018 ERROR: System Call recv
    16.11. 17:37:10.018 ERROR: Error No 60
    16.11. 17:37:10.018 ERROR: 'Operation timed out'
    ERROR #############################
    16.11. 17:37:10.018 CON: -
    16.11. 17:37:10.018 CON: GuiNiNetConnection: sending DIAG data to connection for modus -1
    ERROR #############################
    16.11. 17:37:10.234 ERROR: GuiConnection: Connection closed
    16.11. 17:37:10.234 ERROR: Error: connection to partner '172.23.200.109:3200' broken
    16.11. 17:37:10.234 ERROR: 
    16.11. 17:37:10.234 ERROR: Wed Nov 16 17:37:10 2011
    16.11. 17:37:10.234 ERROR: Release 720
    16.11. 17:37:10.234 ERROR: Component NI (network interface), version 40
    16.11. 17:37:10.234 ERROR: rc = -6, module nixxi.cpp, line 5087
    16.11. 17:37:10.234 ERROR: Detail NiIRead: P=172.23.200.109:3200; L=10.64.10.112:53387
    16.11. 17:37:10.234 ERROR: System Call recv
    16.11. 17:37:10.234 ERROR: Error No 60
    16.11. 17:37:10.234 ERROR: 'Operation timed out'
    ERROR #############################
    ERROR #############################

    Hello Andrew,
    some version of the VPN client on Lion seems to have a known issue according to SAP internal discussions.
    I found someone telling, that with F5 SSL VPN Plugin 7000.2011.0907.01, it is working again.
    It seems to be available from https://connectfp.sap.com.
    For uninstalling old F5 version, see http://support.f5.com/kb/en-us/solutions/public/3000/800/sol3826.html
    (many "seems", because I am still on Snow Leopard and can not talk about this issue from my own experience)
    Regarding user authorization for downloading software in Service MarketPlace, please refer to [note 1037574|https://service.sap.com/sap/support/notes/1037574].
    Best regards
    Rolf-Martin

  • VPN issues after updating to Cisco AnyConnect 3.1.04072?

    Even after downloading the most recent version of Cisco Client 3.1.04072 (see below) I'm still getting a periodic disconnect and reconnect from my VPN client.  Issue only seems to occur when I'm connecting from outside my company's wi-fi network.  Happens on both my personal and on public wi-fi.  Is anyone else experiencing a similar issue?
    Changes in AnyConnect 3.1.04072 (and 3.1.04074)
    The Mac OS X versions of AnyConnect were updated to 3.1.04074 to resolve the problem of frequent disconnects of the AnyConnect VPN on systems running Mac OS X 10.9 (Mavericks). Apple is aware of this issue and you can reference Apple Bug Report ID 15261749 if you want to open your own case with them. AnyConnect 3.1.0474 also supports Mac OS X 10.8, 10.7 and 10.6.
    Once Apple provides a fix for OS X 10.9, we may choose to retract this workaround. At that time, both versions 3.1.04074 and 3.1.04072 of AnyConnect will work reliably with Mac OS X 10.9.
    Defect CSCui69769 was fixed by version 3.1.0704.
    AnyConnect 3.1.04072 is a maintenance release that resolves the defects described in Caveats Resolved by AnyConnect 3.1.04072 and is compatible with Host Scan Engine Update, 3.1.04075.

    Pete is right, I apparently don't know how to read version numbers!  I downloaded the 3.1.05152 version of Cisco AnyConnect, and I no longer experience the reconnect issue on Mavericks.  Yea!
    In my defense, there is no such version 3.1.04074 listed on the download page:
    http://software.cisco.com/portal/pub/download/portal/select.html?&mdfid=28300018 5&flowid=17001&softwareid=282364313
    So I mistakenly downloaded 3.1.04072 in a moment of dyslexia.  I suspect I'm not the first person to come along and do this!
    PS:  You need a service contract with Cisco to download this file.  If you don't have one, and/or your IT administrator isn't able to provide you with one, you might try doing a google search for the actual filename:  anyconnect-macosx-i386-3.1.05152-k9.dmg.  If you go this route, at least compare the md5 checksum with the one listed on Cisco's website (it shows up if you hover your cursor over the file) to ensure you're not running a hacked VPN client.  For example, running "md5 anyconnect-macosx-i386-3.1.05152-k9.dmg" should produce a884f2092d08f006b2dc3a5054988f1c.  If it does not, it's not the same binary as on Cisco's downloads page so you probably don't want to run it.

  • Lync internal clients have issues with external meetings

    We have a pretty easy Lync setup in our company, 2 FE servers in a Enterprise pool, one Edge server (in a pool. we will add edge servers later) and a Reverse proxy (Databases on a SQL server of course). Everything seems to be working well internally. We
    have not deployed Enterprise voice yet but that is coming later. Our issue is when our internal clients try to join a meeting from another company. They can join the meeting and IM but as soon as they try to start Voice, they get kicked out of the call. Internal
    meetings work fine with voice and video. They can join the meeting using Lync Web App but that is not a satisfactory solution for this. The company that hosted the meeting said users from other companies can join with the lync client without issue. I am a
    remote employee and I can join using audio and video from my home. I have tried tracing the issue with the lync client logs but they make little sense to me. My question is, how does the information flow from internal clients to an external meeting> Is
    it through the AV service in the Edge? 
      We have opened the firewalls wide open as a test (closed again of course) and it does not seem to be a firewall issue. Can anyone point me in the right direction?

    To both of you, thanks but the articles do not help me. We can host meetings in our Lync 2013 organization without issue and it seems that others from outside can join with either Lync client or LWA. Our remote users connect via Lync client without a VPN
    and have no issues with IM, Audio, video or sharing. The issue is connecting to another companies Lync meeting from inside our network. You can connect but as soon as you try to enable audio, you get kicked out. I have seen another post that describes the
    issue but there is no solution there either. As I said in the original post, we ran a test where we temporarily opened both the internal and external firewalls wide open for the Edge and Reverse Proxy servers and it had no effect whatsoever so I conclude it
    probably is not a firewall issue. Since Edwin verified what I believed in that the communication from the internal clients does go through our companies Edge server when joining a meeting with another company, it leads me to believe that this is
    a setup issue with the Edge server but I have followed the setup documents and nothing seems out of place. Our edge server is a virtual server. I  am wondering if this could be related to it or maybe this is just the way things are. Can anyone
    tell me that their internal users can join a meeting hosted by another company? We have open federation setup at this time and since the company that hosted the meeting claims to have had users from other companies in meetings without issue, I assume their
    SRV records work.

  • WRT54G Ver2 VPN issue

    I have a HUGE issue with the WRT54G Version 2, Firmware 4.21.1. I have been beating my brains out trying to get this to access my clients VPN. After having no luck, I replaced it with my own WRT54G Version 1 and all works fine. All the settings are exactly the same, but I can not get the VPN to connect. Any help or suggestions are greatly appreciated.

    This did not work. In fact, once completed I rebooted the router and was not even able to get back on the Internet. I assumed it was the router, so I bought a new WRT54G Version 8 with Firmware 8.0.0. Guess what, this does not allow VPN traffic either. I find this very odd, since all the settings are correct and ports are opened.

  • Win7 LT2P Clients VPN OSX Server

    Have recently managed to get WIn 7 clients happily connecting to Mountain lion server, (after many hours and registry changes). Having an interesting issue where the WIn7 clients will get an authentication error, if another WIn7 Client is already authenticated, via VPN to the server. This occures even when the second Win7 Client is using a different user account account?
    I wonder if anyone has come across this before? The Apple based VPN clients do not have the same mutiple client instance issue. Did see the odd mention in some online forums, but never any reply's or solutions.
    Thanks in advance.

    I helped steveinsd76 with this issue last night.
    My machine (10.6.8) can connect using L2TP without a problem.. I get an IP and can access resources on the office LAN.
    When steveinsd76 connects, I see IKE packets hit the server, but the server does not respond.  We have triple verified shared secret.
    I had him move his client machine to a different Internet connection, and we see the same issue.
    I have not had time to do much troubleshooting beyond this.
    Any known gotchas here?

  • Limitation on Client VPN for RV220W?

    Is there a limitation on using the Client VPN to connect to the RV220W from the same location (site)?
    Here’s what happened: One of our RV220W’s went down and we UPS’d it back to Cisco for replacement; so that was the end of our site-to-site connection. I ran to Staples and brought a $200 Netgear R6300v2 Smart WiFi Router, thinking it would be a nice "backup" router should a Cisco router go down in the future again, and also at the $200 price poing and being the "newest" model out, it would have what I need. What I didn’t know is the Netgear R6300v2 is a "consumer" router with no VPN capabilities, so it can not establish a site-to-site VPN connection. So, I figure a cool work around was to have each workstation connect to the other RV220W at the other location. But...I’m finding out that when one workstation is connected, no other workstation can connect: it times out during verification. When I disconnect the workstation that is connected, then another workstation can connect through the Client VPN.
    Does this one-at-a-time connection only happen ‘cause we’re all at the same location, trying to connect from the same WAN IP address, in essence the same site?
    If so, what would happen if two or more employees wanted to use the Client VPN from the same Starbuck’s location? Would they NOT be allowed to connect at the same time? The first one would connect, and the second one would not connect?

    Hi Waverly,
    As I understand it, the QuickVPN routers can only accept a single connection at a time from the same remote WAN IP. You *may be able to make another connection by using port 60443 on the second client.
    You can also use PPTP and/or SSL VPN on the RV220W. Clearly the best option is a site to site tunnel for multiple users. The RV180(W) might be a better choice for a backup router as it has nearly all of the capabilities of the RV220W at less cost.
    - Marty

  • Remote access Vpn issue

    Dear All,
    I have configured remote access vpn without using split tunnel.Everything is working fine.I can access all the inside network which is allowed in acl.
    I am facing strange issue now. I have created a pool for remote access vpn with a range 192.168.5.8/29.I can access my internal subnets 10.10.0.0/16.
    I have below acess-list for acl-in.
    access-list acl-in extended permit ip object-group vpnclients 192.168.5.8 255.255.255.248
    object-group network vpnclients
    network-object host 10.110.100.26
    network-object host 10.106.100.15
    network-object host 10.10.10.6
    network-object host 10.10.20.82
    network-object host 10.110.100.48
    network-object host 10.10.20.53
    network-object host 10.10.20.54
    network-object host 10.60.100.1
    network-object host 10.10.10.75
    network-object host 10.10.20.100
    network-object host 10.10.130.136
    network-object host 10.106.100.16
    network-object host 10.106.100.9
    network-object host 10.170.100.1
    network-object host 10.170.100.2
    network-object host 10.170.100.21
    network-object host 10.101.100.20
    network-object host 10.170.100.25
    So whichever IPs i have called in vpnclient group is able to access via RA vpn.Issue is when i try to access internal network of 192.168.198.0/24, i am able to access it without adding in vpnclient group. Even for 192.168.197.0/24,192.168.197.0/24 the same. But for 10.10.0.0/16 we can access only after adding in vpnclient group. Any one has face this issue before. Is this because of same network i mean 192.168.0.0 something like that.There is no other staement in acl-in for 192.168.0.0
    Regards
    -Danesh Ahammad

    Hi,
    If i read correctly you made the RA vpn "without"  split tunnel, correct? if that is the case, all of the traffic will traverse the vpn connection (tunnel all) , the access-list "acl-in" is of no use to it.
    try converting it to use split tunnel, i am sure that way you can not access resources that are not mentioned in the list.
    ~Harry

  • Cisco 2504 WLC client VPN Access

    Hi,
    I was reading couple of posts related to Cisco WLC + Client VPN passthrough .. and got  a query.
    https://supportforums.cisco.com/thread/2183687
    https://supportforums.cisco.com/thread/2219356
    The second link says that "Remote Acces VPN connections through the WLC work out of the box". Is this True? No need to configure Layer 3 VPN-Pass though for the SSID?
    They are using WPA2+PSK as Layer 2 Security. Here WPA2-PSK + VPN Passthrough is the right combination for WLAN Layer2 + Layer 3 Security?
    Thanks,
    Jagan

    It works out of the box... you don't need to configure any passthrough.. just connect to the ssid and VPN away.
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • Forefront TMG network policy server and VPN issue.

    Hello every one!
    I have a problem with configuration VPN server on Forefront TMG on Windows Server 2008R2 with latests microsoft updates.
    I install Forefront TMG on on Windows Server 2008R2 with latest updates.
    Then, I configure startup wizard where I set network configuration and etc.
    Next, I set VPN settings, I set DHCP pool, DNS servers, Access groups for VPN, and set PPTP.
    After apply this settings, service RemoteAccess doesn't start. I try to reboot server but service doesn't start.
    But it's not one problem.
    When I add VPN Access groups in Forefront, and apply configuration, I don't see changes in network policy server (nps.msc) Groups don't add to policy in network policy server.
    Screenshot
    If I start RemoteAccess manually and add new VPN Access groups in policy in network policy server, I can use VPN server, and connect to forefront server.
    But I don't understand why TMG Forefront can't apply this settings in nps.msc and services.
    What I do wrong?
    I Use Windows Server 2008R2
    Forefront TMG RTM 7.0.7734.100

    Hello! Thank you for your help!
    I see this link
    http://www.isaserver.org/articles-tutorials/configuration-security/Implementing-Secure-Remote-Access-PPTP-Forefront-Threat-Management-Gateway-TMG-2010-Part2.html
    But I don't use RADIUS server in my Forefront TMG VPN configuration.
    I configure client VPN Access via PPTP
    When I configure TMG VPN settings, I set VPN Access groups. After that NPS server change and apply TMG network policy correctly.
    But if I change some TMG firewall policy, and then I  try to add VPN Access groups (screenshot -
    http://i.gyazo.com/34a34ba18a01c58689e5e3cddbc52585.png) NPS server can't change and apply TMG network policy correctly.
    Now I have a two Access groups in TMG VPN settings
    http://i.gyazo.com/34a34ba18a01c58689e5e3cddbc52585.png
    And I have a NPS server network policy with not correctly settings
    http://i.gyazo.com/1dd973ca9cc2a228d54a53d88ca90009.png
    Forefront can't change NPS server network policy. I don't undesrtand where problem.
    I try to reinstall TMG on new machine, but problem
    problem persists.

  • Pix 501 and Client VPN's

    Hi, I've had this 501 for several months now and really stuggled to get the client VPN side working.
    I can get site to site working with no problems using the wizard but the Client VPN never works.
    Latest i've set it up for pptp which I can get the client to connect with no problems but fails to get any traffic from the pix - I can however ping the remote PC from a PC behind the PIX.
    I'm setting these up by the PDM buy i've attached a copy of the config anyway.
    Best,
    Chris

    Hi Kamal.
    It didnt like the command
    nat (inside) 0 access0list nonat
    I can attach via Cisco VPN Client but the same occurs - I can ping the remote from the network - but not the other way round.
    Config attached. - Best, Chris
    : Written by enable_15 at 02:14:05.990 UTC Mon Feb 12 2007
    PIX Version 6.3(5)
    interface ethernet0 auto
    interface ethernet1 100full
    nameif ethernet0 outside security0
    nameif ethernet1 inside security100
    enable password xxx
    passwd xxx
    hostname pixfirewall
    domain-name ciscopix.com
    fixup protocol dns maximum-length 512
    fixup protocol ftp 21
    fixup protocol h323 h225 1720
    fixup protocol h323 ras 1718-1719
    fixup protocol http 80
    fixup protocol rsh 514
    fixup protocol rtsp 554
    fixup protocol sip 5060
    fixup protocol sip udp 5060
    fixup protocol skinny 2000
    fixup protocol smtp 25
    fixup protocol sqlnet 1521
    fixup protocol tftp 69
    names
    access-list nonat permit ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0
    access-list outside_cryptomap_dyn_20 permit ip any 10.10.10.0 255.255.255.240
    access-list split permit ip 192.168.1.0 255.255.255.0 any
    pager lines 24
    mtu outside 1500
    mtu inside 1500
    ip address outside 213.x.146.72 255.255.x.0
    ip address inside 192.168.1.1 255.255.255.0
    ip audit info action alarm
    ip audit attack action alarm
    ip local pool vpnpool 10.10.10.1-10.10.10.10
    pdm logging informational 100
    pdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 1 0.0.0.0 0.0.0.0 0 0
    route outside 0.0.0.0 0.0.0.x.249.x.65 1
    timeout xlate 0:05:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
    timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
    timeout sip-disconnect 0:02:00 sip-invite 0:03:00
    timeout uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server TACACS+ max-failed-attempts 3
    aaa-server TACACS+ deadtime 10
    aaa-server RADIUS protocol radius
    aaa-server RADIUS max-failed-attempts 3
    aaa-server RADIUS deadtime 10
    aaa-server LOCAL protocol local
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    no snmp-server enable traps
    floodguard enable
    sysopt connection permit-ipsec
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set myset esp-des esp-md5-hmac
    crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
    crypto dynamic-map cisco 1 set transform-set myset
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map client authentication LOCAL
    crypto map dyn-map 20 ipsec-isakmp dynamic cisco
    crypto map dyn-map interface outside
    isakmp enable outside
    isakmp nat-traversal 20
    isakmp policy 10 authentication pre-share
    isakmp policy 10 encryption 3des
    isakmp policy 10 hash md5
    isakmp policy 10 group 1
    isakmp policy 10 lifetime 86400
    isakmp policy 20 authentication pre-share
    isakmp policy 20 encryption 3des
    isakmp policy 20 hash md5
    isakmp policy 20 group 2
    isakmp policy 20 lifetime 86400
    vpngroup vpn address-pool vpnpool
    vpngroup vpn dns-server 192.168.1.1
    vpngroup vpn idle-time 1800
    vpngroup vpn password 634083
    vpngroup VPNclient split-tunnel split
    vpngroup VPNclient idle-time 1800
    vpngroup VPNclient password ******
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd address 192.168.1.2-192.168.1.33 inside
    dhcpd dns 89.238.129.211
    dhcpd lease 3600
    dhcpd ping_timeout 750
    dhcpd auto_config outside
    dhcpd enable inside
    username chris password 9DgK/T8KJkq.BhX6 encrypted privilege 15
    terminal width 80
    Cryptochecksum:xxx
    : end

  • How to install MX60 and enable client vpn services

    Can anyone show me a link or video that will assist in installing MX60 and enable client VPN services?

    Thanks Brandon. I will explore the Meraki knowledge base link you sent.

  • Cuantos Clientes VPN soporta el cisco rv042g?

    Quisiera saber cuantos clientes VPN conectados simultáneamente soporta el cisco rv042g, ya que necesito conectar 10 clientes, pero al conectar 3 simultáneos se vuelve inestable la conexión y automáticamente desconecta a un cliente.

    Muy buenos dias, 
    Siento mucho que este tendiendo problemas con la conexión VPN en este router.
    La respuesta a su pregunta es la siguiente\
    VPN 
     QuickVPN 
     50 QuickVPN tunnels for remote client access 
     PPTP 
     5 PPTP tunnels for remote access
    De cualquier manera, no debería de tener problemas si solo esta usando 3.
    Diganos por favor que tipo de conexión VPN esta usando, cual es la velocidad de descarga y subida de su conexión de internet y si puede dar mas information acerca de su problema en especifico, eso nos puede ayudar a ver que opciones hay disponibles.

Maybe you are looking for