CME 8.6 running on PUBLIC IP . should I do NAT ?
Hello All
I have a CME 8.6 router with one PUBLIC IP to eth0 interface.
Do you need to do NAT for all IP phone to make and receive calls ?
Currently I have configured NAT and I did not BIND media to any interface . I could able to make calls but Audio is one way . Other party can not hear anyting.
cme#show run
Building configuration...
voice service voip
ip address trusted list
ipv4 192.168.4.0 255.255.255.0
ipv4 x.x.x.x 255.255.255.255
allow-connections sip to sip
no supplementary-service h450.2
no supplementary-service h450.3
no supplementary-service h450.7
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
no supplementary-service sip handle-replaces
sip
registrar server expires max 3600 min 1800
voice register global
mode cme
source-address 192.168.1.3 port 5060
max-dn 60
max-pool 50
load 9971 sip9971.9-4-1SR1-2
load 9951 sip9951.9-4-1SR1-2
authenticate register
date-format D/M/Y
tftp-path flash:
create profile sync 002035708611093A
ntp-server 128.138.141.172 mode directedbroadcast
camera
video
voice register dn 10
number 123
allow watch
label Home
voice register pool 1
id mac 00000000
type 9971
number 1 dn 1
dtmf-relay rtp-nte
username 111 password 111
codec g711ulaw
camera
video
voice-card 0
dsp services dspfarm
interface GigabitEthernet0/0
ip address XXXXXXXX
ip access-group tool_check in
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
interface GigabitEthernet0/1.1000
encapsulation dot1Q 1000
ip address 192.168.1.3 255.255.255.0
ip nat inside
ip virtual-reassembly in
router ospf 1
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 7 interface GigabitEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 x.x.x.x
ip access-list extended tool_check
permit ip host x.x.x.x any
deny ip any any
access-list 7 permit 192.168.1.0 0.0.0.255
tftp-server flash:sip9971.9-4-1SR1-2.loads alias sip9971.9-4-1SR1-2.loads
tftp-server flash:sip9951.9-4-1SR1-2.loads alias sip9951.9-4-1SR1-2.loads
tftp-server flash:dkern9971.100609R2-9-4-1SR1-2.sebn alias dkern9971.100609R2-9-4-1SR1-2.sebn
tftp-server flash:kern9971.9-4-1SR1-2.sebn alias kern9971.9-4-1SR1-2.sebn
tftp-server flash:rootfs9971.9-4-1SR1-2.sebn alias rootfs9971.9-4-1SR1-2.sebn
tftp-server flash:sboot9971.031610R1-9-4-1SR1-2.sebn alias sboot9971.031610R1-9-4-1SR1-2.sebn
tftp-server flash:skern9971.022809R2-9-4-1SR1-2.sebn alias skern9971.022809R2-9-4-1SR1-2.sebn
tftp-server flash:dkern9951.100609R2-9-4-1SR1-2.sebn alias dkern9951.100609R2-9-4-1SR1-2.sebn
tftp-server flash:kern9951.9-4-1SR1-2.sebn alias kern9951.9-4-1SR1-2.sebn
tftp-server flash:rootfs9951.9-4-1SR1-2.sebn alias rootfs9951.9-4-1SR1-2.sebn
tftp-server flash:sboot9951.031610R1-9-4-1SR1-2.sebn alias sboot9951.031610R1-9-4-1SR1-2.sebn
tftp-server flash:skern9951.022809R2-9-4-1SR1-2.sebn alias skern9951.022809R2-9-4-1SR1-2.sebn
tftp-server flash:English_United_States/gd-sip.jar alias gd-sip.jar
tftp-server flash:g4-tones.xml alias United_States/g4-tones.xml
tftp-server flash:gd-sip.jar alias English_United_States/gd-sip.jar
tftp-server flash:sip9971.9-1-1SR1.loads alias sip9971.9-1-1SR1.loads
tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
dial-peer voice 21 voip
description 13
destination-pattern 13....
b2bua
session protocol sipv2
session target dns:x.x.x.x
dtmf-relay rtp-nte
codec g711ulaw
no vad
sip-ua
timers connect 100
telephony-service
no auto-reg-ephone
max-dn 60
ip source-address 192.168.1.3 port 2000
max-redirect 9
cnf-file location flash:
date-format dd-mm-yy
max-conferences 8 gain -6
call-park system application
moh flash:/music-on-hold.au
transfer-system full-consult
secondary-dialtone 0
after-hours block pattern 1 001
after-hours block pattern 2 011
after-hours block pattern 3 000
after-hours day Sun 00:00 23:59
after-hours day Mon 00:00 23:59
after-hours day Tue 00:00 23:59
after-hours day Wed 00:00 23:59
after-hours day Thu 00:00 23:59
after-hours day Fri 00:00 23:59
after-hours day Sat 00:00 23:59
create cnf-files version-stamp 7960 Jan 21 2015 09:19:19
Could anyone please help me what I am missing ?
Thanks
Call Apple to see about purchasing Snow Leopard on a disc. I was able to do so even though it doesn't show in the online store. I think it was around $20. Once you install that, run Software Update to get up to 10.6.8.
You don't need to have 10.7 or 10.8 to get to Mavericks (as long as your machine will support it).
Similar Messages
-
No matter which page i run... i should get the home page first
Hi,
i have some jspx pages in my application
No matter which page i run... i should get the home page first
Because there is a chance that the user might remember the url of a certain page and copy paste that one in the browser... in such type of scenarios also home page should come first
After i implemented Adf security in the redirect upon successful login i took the home.jspx page... but it is not going to home.jspx when i run some 'x' page and give the credentials for authentication.
This for our project they dont want to implement at taskflow level for each and every taskflow... is there any higher level where we can implement such feature because home page is common for all.
Thanx,No matter which page i run... i should get the home page first
Because there is a chance that the user might remember the url of a certain page and copy paste that one in the browser... in such type of scenarios also home page should come first
After i implemented Adf security in the redirect upon successful login i took the home.jspx page... but it is not going to home.jspx when i run some 'x' page and give the credentials for authentication.Just create a filter and put some logic like the one below:
if(!request.getRequestURI().contains("homePage"))
((HttpServletResponse)servletResponse).sendRedirect("http://server/yourApp/faces/homePage");
else
filterChain.doFilter(request, servletResponse);You can easily search for how to create a web application filter and register it in web.xml .. -
My mac book pro is running really slow what should I do?
My mac book pro is running really slow what should I do?
Things You Can Do To Resolve Slow Downs
If your computer seems to be running slower here are some things you can do:
Start with visits to: OS X Maintenance - MacAttorney;
The X Lab: The X-FAQs;
The Safe Mac » Mac Performance Guide;
The Safe Mac » The myth of the dirty Mac;
Mac maintenance Quick Assist.
Boot into Safe Mode then repair your hard drive and permissions:
Repair the Hard Drive and Permissions Pre-Lion
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
Repair the Hard Drive - Lion/Mountain Lion/Mavericks
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the Utilites Menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD disk icon and click on the arrow button below.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
Restart your computer normally and see if this has helped any. Next do some maintenance:
For situations Disk Utility cannot handle the best third-party utility is Disk Warrior; DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible.
Note: Alsoft ships DW on a bootable DVD that will startup Macs running Snow Leopard or earlier. It cannot start Macs that came with Lion or later pre-installed, however, DW will work on those models.
Suggestions for OS X Maintenance
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep. Dependence upon third-party utilities to run the periodic maintenance scripts was significantly reduced since Tiger. These utilities have limited or no functionality with Snow Leopard or later and should not be installed.
OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive.
Helpful Links Regarding Malware Protection
An excellent link to read is Tom Reed's Mac Malware Guide.
Also, visit The XLab FAQs and read Detecting and avoiding malware and spyware.
See these Apple articles:
Mac OS X Snow Leopard and malware detection
OS X Lion- Protect your Mac from malware
OS X Mountain Lion- Protect your Mac from malware
About file quarantine in OS X
If you require anti-virus protection I recommend using VirusBarrier Express 1.1.6 or Dr.Web Light both from the App Store. They're both free, and since they're from the App Store, they won't destabilize the system. (Thank you to Thomas Reed for these recommendations.)
Troubleshooting Applications
I recommend downloading a utility such as TinkerTool System, OnyX, Mavericks Cache Cleaner, or Cocktail that you can use for removing old log files and archives, clearing caches, etc. Corrupted cache, log, or temporary files can cause application or OS X crashes as well as kernel panics.
If you have Snow Leopard or Leopard, then for similar repairs install the freeware utility Applejack. If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the command line. Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. Applejack does not work with Lion and later.
Basic Backup
For some people Time Machine will be more than adequate. Time Machine is part of OS X. There are two components:
1. A Time Machine preferences panel as part of System Preferences;
2. A Time Machine application located in the Applications folder. It is
used to manage backups and to restore backups. Time Machine
requires a backup drive that is at least twice the capacity of the
drive being backed up.
Alternatively, get an external drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
1. Carbon Copy Cloner
2. Get Backup
3. Deja Vu
4. SuperDuper!
5. Synk Pro
6. Tri-Backup
Visit The XLab FAQs and read the FAQ on backup and restore. Also read How to Back Up and Restore Your Files. For help with using Time Machine visit Pondini's Time Machine FAQ for help with all things Time Machine.
Referenced software can be found at MacUpdate.
Additional Hints
Be sure you have an adequate amount of RAM installed for the number of applications you run concurrently. Be sure you leave a minimum of 10% of the hard drive's capacity as free space.
Add more RAM. If your computer has less than 2 GBs of RAM and you are using OS X Leopard or later, then you can do with more RAM. Snow Leopard and Lion work much better with 4 GBs of RAM than their system minimums. The more concurrent applications you tend to use the more RAM you should have.
Always maintain at least 15 GBs or 10% of your hard drive's capacity as free space, whichever is greater. OS X is frequently accessing your hard drive, so providing adequate free space will keep things from slowing down.
Check for applications that may be hogging the CPU:
Pre-Mavericks
Open Activity Monitor in the Utilities folder. Select All Processes from the Processes dropdown menu. Click twice on the CPU% column header to display in descending order. If you find a process using a large amount of CPU time (>=70,) then select the process and click on the Quit icon in the toolbar. Click on the Force Quit button to kill the process. See if that helps. Be sure to note the name of the runaway process so you can track down the cause of the problem.
Mavericks and later
Open Activity Monitor in the Utilities folder. Select All Processes from the View menu. Click on the CPU tab in the toolbar. Click twice on the CPU% column header to display in descending order. If you find a process using a large amount of CPU time (>=70,) then select the process and click on the Quit icon in the toolbar. Click on the Force Quit button to kill the process. See if that helps. Be sure to note the name of the runaway process so you can track down the cause of the problem.
Often this problem occurs because of a corrupted cache or preferences file or an attempt to write to a corrupted log file. -
I use Firefox 6.0.2. When I shut the browser and try to reopen it I get a message saying that Firefox is still running and that I should reboot. This happens constantly. Why does this happen and is there a way around it?
There are a few possible causes for that error, for details see [[Firefox is already running but is not responding]].
-
I'm running OS X what should I upgrade to?
I'm running OS X what should I upgrade to?
Hi,
If your forum info is up to date, you're currently running OS X 10.5.8 Leopard. If you want to update to the more recent versions like Lion or Mountain Lion when it's released, you first have to buy Snow Leopard, which is version 10.6. You can still get that on the online Apple Store here or at any Apple Retailer (I think).
Hope that helps you out, feel free to ask anything else.
J -
am trying to restore the bak file into a new site collection in my sp 2010 standalone env.
am getting error
PS C:\Windows\system32> stsadm -o restore -url http://srvr1-01:123/sites/Repository -filename "C:\mBKUPCOPY\Sharepoint_bankup.bak"
STSADM.EXE : Your backup is from a different version of Microsoft SharePoint Foundation and cannot be restored to a server running
the current version. The backup file should be restored to a server with version '12.0.0.6318' or later.
At line:1 char:1
+ stsadm -o restore -url http://srvr1-01:123/sites/Repository -filename "C: ...
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : NotSpecified: (Your backup is ...6318' or later.:String) [], RemoteException
+ FullyQualifiedErrorId : NativeCommandErrorAs stated in the other thread on this topic you can't restore a 2007 backup to 2010, it needs to be upgraded.
https://social.technet.microsoft.com/Forums/en-US/31c70f0a-5d89-4308-895b-af0c2b249114/restore-the-site-collection-from-moss-2007-to-sp-2010-site-collec?forum=sharepointadminprevious -
My Mac feels as if it is running slower these last couple of months. I have thought of pursuing a commercially available "clean up" product, but thought I would try the community first and also for pointers using the Mac's own internal diagnostics or system improvement capabilities. Any and all advice is most welcome. I have a 250GB hard drive that is half full, I always update to latest revisions and have an extra high-speed internet connection. Computer is not heavily loaded with apps and typically using Firefox for browsing. (MS Office for Mac as well, but usually limited to one program such as MS Word or Excel at a time.) No heavy graphics utilization. Videos from the internet load slowly and some are choppy. Even scrolling just doesn't seem "brisk".
Thank you,
TomDisconnect all wired peripherals except keyboard, mouse, and monitor, if applicable. Launch the usual set of applications you use when you notice the slowdown.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Activity Monitor in the page that opens.
Select the CPU tab. Select All Processes from the menu in the toolbar, if not already selected. Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Now select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Step 2
Launch the Console application in the same way as above, and select “kernel.log” from the file list. Post the dozen or so most recent messages in the log – the text, please, not a screenshot. If there are repeats, please post only one example of each repeated message. -
I,ve got the mid 2011 2.7 ghz imac running m lion. Should i use bootcamp or third-party software?
The reason i ask is due to my lack of faith in apples software. I,ve tried s leopard, lion and now m lion and my imac is still slower than all my friends windows computers. whether its internet based or non internet based its always slow. in my defense the imac choice was based on my ipad 2 which is ace. the imac cost over £1300 and i expected a lot better. Anyway i use it for gaming quite a lot and i,m prepared to upgrade the graphics card and buy windows 7 or 8 just for game accessability and the option of being able to use a gamepad that actually works with the imac. Are there any risks or disadvantages involved with using boot camp. I don,t have much confidence in Apples software as every system i,ve used has bricked my computer and caused me to reinstall due to apple software conflicts. (Apple tech supports theory and they charged me £35 for this little nugget even though i bought the imac Jan 2012 new). i refuse to pay for a backup solution as i think it should be free like system restore on windows. I purposefully don,t store anything important on the imac due to past probs so losing data i can live with. Slowing it down further i cannot. Please help.
you can't upgrade the video cards on imacs
it's confusing what you are asking bootcamp is apples software which let you run windows native on your imac
the alternative is parallels or virtualbox if you need to run windows apps and those being emulated and will not have full access to the video card would not be good for gaming -
While running F110 mail trigger should happen at the time of payment Run
Hi Experts,
I have configured FBZP and automatic mail trigger for Payment Advice also. Now while running F110 then at the time of Proposal Run the mail is getting triggered. But since its proposal it can be edited also. So I need the mail should trigger at the time of Payment Run. Plz suggest how to achieve this.
Thanks in Advance,
ArabindaCheck this note: 836169
may be helpful with the config and setup, its a consulting note.... -
My Mac os X version 10.5.8 is running slow. What should I do?
Hi. My imac is running slowly. My applecare ran out in August. Any suggestions as to what I should try?
Sure. First make a cloned backup of your current system to an external hard drive:
Clone using Restore Option of Disk Utility
Open Disk Utility from the Utilities folder.
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the external backup drive. Source means the internal startup drive.
Second, buy a copy of Snow Leopard at your local Apple Store or the Online Store ($29.00.)
Third, install Snow Leopard:
1. Boot from the Snow Leopard Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. After formatting has completed quit DU and return to the installer. Complete the Snow Leopard installation.
After Snow Leopard starts for the first time you will be taken to the Setup Assistant. There you will be given the opportunity to restore your files from a TM backup, another Mac, or a connected hard drive. Choose the option to restore from a connected hard drive. You will then be able to restore your Home folder, third-party applications and support files, and system preferences. -
How to config BSP to run in public network
Dear BSP experts
I am new to BSP development , i have create one BSP application , and test ok in SAP , and got the URL of the BSP ,it can be tested within our company using the URL , but not outside . so do i need to config something so i can run this BSP application anywhere ? and how ? thanks
Best Regards
JackyHi Jacky,
You need to assign public IP to your SAP system to be accessed from internet (outside your LAN) and the domain name to be assigned to the server and registered in DNS.
Otherwise, use web dispatcher to catch and redirect the requests to SAP server.
Regards,
Ravi -
Published project runs slower than it should
Hello all,
I've been using Captivate 2 for a while after upgrading from
Captivate 1. I'm creating a training/tutorial project which is
around ten minutes long. Essentially loads of screen
recordings/captures on a Windows 2000 machine.
The project is 275 slides in total and the .cp file is around
70Mb. When published/compiled .SWF file is around 12Mb. Initially
the .cp file was around 200Mb but I used the Save As trick as
described in other posts to shrink the size.
I've put audio tracks on the individual slides (not all -
probably around 50-60 slides contain audio) and I've taken taken
time to adjust the timing so that it all flows nicely.
When I preview the project within Captivate it all runs as
expected - however, when I publish the project and run it on a
variety of other machines, it starts off well but gets to parts
where it slloooooowss right down - mouse movements take an age and
generally it all goes to pot.
Are others experiencing this? How can I fix it?
Thanks,
Rod.Hi Rod and welcome to our community
I hate to be the bearer of bad news, but you do need to know,
so here goes. Your project is about 200 slides beyond the "rule of
thumb" recommended upper limit for efficient Captivate projects.
It's surprising you haven't yet had it corrupt on you.
If I were in your shoes, here is how I would proceed.
Open that 275 slide project and click File > Save As and
maybe call this one Segment one.
Delete all slides beyond perhaps slide 70.
Save and reopen the original.
Click File > Save As and maybe call this one Segment two.
Delete the first 70 slides.
Delete all slides beyond the new slide 70.
Rinse and repeat as needed until you end up with several
projects that are fairly equally sized.
Now open each project and examine the preferences. Look at
the Start and End preferences. Set the end action of each project
to "Open other project". Then you point at the next project in the
sequence. This is called "Daisy Chaining".
You should end up with a more efficient movie that works
better for your user.
Cheers... Rick -
Mac mini is running slow what steps should I take to determine what's slowing it down? New to MAC
My Mac mini is running very slow, I suspect it is a software problem. I'm new to Mac and would appreciate some suggestions on what steps to take.
When you see a beachball cursor or the slowness is especially bad, note the exact time: hour, minute, second.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
The title of the Console window should be All Messages. If it isn't, select
SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting. -
Kernel task is hogging up my computer and fan is running high. What should I do?
I have a mac air 1.6 ghz intel icore 5 with 2 gb memory. Ive been noticing my fan running high and consistantly when my external harddrive is plugged in and just surfing and posting images on facebook. Very basic stuff.
Ive noticed in my activity monitor that kernel task is hogging up a lot of space on my computer. How do I get rid of it? and wth is it?
The fans are running high as I said. I continually reset the SMC and it keeping coming back on high.
Should I be worried about the longevity of my mac air?
What do you experts suggest I do?
Thank You in advance.From this article: http://support.apple.com/kb/TS3694
Error 1004, 1013, 1638, 3194: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors:
Install the latest version of iTunes.
Check security software. Ensure that communication to gs.apple.com is allowed. Follow this article for assistance with security software. iTunes for Windows: Troubleshooting security software issues.
Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. FollowiTunes: Advanced iTunes Store troubleshooting to edit the hosts file or revert to a default hosts file. See section "Blocked by configuration: (Mac OS X/Windows) > Rebuild network information".
Try to restore from another known-good computer and network.
If the errors persist on another computer, the device may need service. -
HT2305 have a notebook running 10.5.8 - should I upgrade the software or buy another computer?
Have a macbook runniing osx 10.5.8 should I buy a new computer or upgrade the software?
That's your choice. Without know what your exact model is here is the upgrade path for OS X:
Upgrade Paths to Snow Leopard, Lion, and/or Mountain Lion
You can upgrade to Mountain Lion from Lion or directly from Snow Leopard. Mountain Lion can be downloaded from the Mac App Store for $19.99. To access the App Store you must have Snow Leopard 10.6.6 or later installed.
Upgrading to Snow Leopard
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard — Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
Snow Leopard General Requirements
1. Mac computer with an Intel processor
2. 1GB of memory
3. 5GB of available disk space
4. DVD drive for installation
5. Some features require a compatible Internet service provider;
fees may apply.
6. Some features require Apple’s iCloud services; fees and
terms apply.
Upgrading to Lion
If your computer does not meet the requirements to install Mountain Lion, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service — this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
or Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply.
Upgrading to Mountain Lion
To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase and download Mountain Lion from the App Store. Sign in using your Apple ID. Mountain Lion is $19.99 plus tax. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
OS X Mountain Lion — System Requirements
Macs that can be upgraded to OS X Mountain Lion
1. iMac (Mid 2007 or newer) — Model Identifier 7,1 or later
2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) —
Model Identifier 5,1 or later
3. MacBook Pro (Mid/Late 2007 or newer) — Model Identifier 3,1 or later
4. MacBook Air (Late 2008 or newer) — Model Identifier 2,1 or later
5. Mac mini (Early 2009 or newer) — Model Identifier 3,1 or later
6. Mac Pro (Early 2008 or newer) — Model Identifier 3,1 or later
7. Xserve (Early 2009) — Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
Are my applications compatible?
See App Compatibility Table — RoaringApps.
For a complete How-To introduction from Apple see Upgrade to OS X Mountain Lion.
If your model is a plastic housed MacBook then I would buy a new computer. If you have a model from Late 2008 or later, then it's a matter of just how old it is. The last MacBook was in 2010, and that model would run Mountain Lion OK. Prior to that I would stick with Snow Leopard.
Maybe you are looking for
-
Records not populating in BEx report
I have a business content cube which was installed once in august. I run a query from that cube, and got records upto the august. I have lots of new records after august too, but its not coming into my query. I thought I have to update my cube. I don
-
How to scan data from one internal table to another
Hi All, let me know how to scan all from one internal table to another internal table. Pls provide me the syntax and code. i am very thankful to you all in advance. Thanks & Regards, Nagarjuna.
-
Does anybody have the same problem?
-
I press the power button, and no response. Computer was last used on Friday, two days later it's unresponsive...
-
Hello I have a problem with an internationalized app. I need to change the input locale of the system depending on which textfield has taken the focus, in this case, from hebrew to english and vice versa without using ALT+SHIFT. I got it using a C li