CME and SRST user documentation

Hi all,
I am pretty new to IPT, and asked to prepare some documentation of CME and SRST on following:-
1. Pro and Con of deploy CME
2. Pro and Con of deploy SRST
3. Any comparison table between CME and SRST
4. Sample documentation of showing to users in a CME site on how to use the CME function. Example: user making call to other CME site or other SRST site.
5. Sample documentation of showing to users in a SRST site on how to use the SRST function. Example: user making call to other SRST site or other CME site.
Would appreciate anyone here to share your advice or experience, share of any link/url if you happen to see similar document. :-)
Thanks.
Regards,
Christopher

You should understand first that SRST is really nothing more than emergency mode for CM gateways or remote locations.
Comparing CM to CME makes sense, comparing CME to SRST does not.
However, it is impossible to put together comparisons and make recommendations unless you have previous experience with all these products.
So I recomend you get help from a reputable consultant or certified cisco partner.

Similar Messages

CME and user services

Can someone please tell me if CME allows users to configure their own speed dials and services using a url like on the CCM? If possible, can you please let me know what I would have to configure to allow this functionality? Thank you.

Hi Rose,
My understanding is that the "Personal" Speed dials can only be changed via the User's IP Phone except for User's who are running Extension Mobility (who can use the GUI interface). There is some excellent info in the last doc attached below;
To use a phone user account in the Cisco Unified CME GUI to configure speed dials on a phone that is enabled for Extension Mobility, Cisco Unified CME GUI 4.2.1 or a later version must be installed on the Cisco router.
Cisco Unified CME GUI Support
The Cisco Unified CME GUI provides a web-based interface to manage most system-level and phone-based features. In particular, the GUI facilitates the routine additions and changes associated with employee turnover, allowing these changes to be performed by nontechnical staff. The GUI provides three levels of access to support the following user classes:
â¢System administrator-Able to configure all system-level and phone-based features. This person is familiar with Cisco IOS software and VoIP network configuration.
â¢Customer administrator-Able to perform routine phone additions and changes without having access to system-level features. This person does not have to be familiar with Cisco IOS software.
â¢Phone user-Able to program a small set of features on his or her own phone and search the Cisco Unified CME directory. In Cisco Unified CME GUI 4.2.1 and later versions, phone users can use the GUI to set up personal speed dials for an Extension Mobility phone. The same credential for logging into an Extension Mobility phone can be used to log into the Cisco Unified CME GUI.
The user name parameter of any authentication credential must be unique. Do not use the same value for a user name when you configure any two or more authentication credentials in Cisco Unified CME, such as the username for any Cisco United CME GUI account and the user name in a logout or user profile for Extension Mobility.
The Cisco Unified CME GUI uses HTTP to transfer information from the router to the PC of an administrator or phone user. The router must be configured as an HTTP server, and an initial system administrator username and password must be defined from the router command-line interface (CLI). Additional accounts for customer administrators and phone users can be added from the Cisco Unified CME router using Cisco IOS software commands or from a PC using GUI screens.
Enabling the GUI
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmegui.html
Configuring Speed Dial
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmespeed.html
Hope this helps!
Rob

ANN: 1/2-hr webinar (free), June 5 -- Enable and encourage user input in PDFs (viewed with Adobe Rea

Enable and encourage user input in PDFs (viewed with Adobe Reader)
with FrameMaker-to-Acrobat TimeSavers + Form Assistant
Half-hour webinar (free; no fluff, no hype, no nonsense)
Wednesday, June 5, starting 9am PDT
Register at: https://www3.gotomeeting.com/register/157658438
Enabling PDFs for various types of user input can strengthen the interaction between users and the content, and improve satisfaction due to greater user involvement/control. In addition, designated avenues for user input can contribute to documentation quality and provide outlet for frustration, for example by sending inputs regarding the documentation or the product directly from within the PDF.
Techniques demonstrated in this webinar include features that are all embedded in PDFs that are viewed with the free Adobe Reader:
• text fields where users can record data values and options
• checkboxes to track progress
• page marks and notes (optionally e-mailed)
• embedded grading/feedback forms
• storing of useful search queries within the PDF for future use
Shlomo Perets
MicroType, http://www.microtype.com
FrameMaker/Acrobat/Captivate training & consulting • FM-to-Acrobat TimeSavers/Assistants

https://crash-stats.mozilla.com/report/index/bp-0a0b872f-5127-4ee1-a355-ca3cb2120721
https://crash-stats.mozilla.com/report/index/bp-9cd87dd7-205f-4844-9e6d-3ce262120721
https://crash-stats.mozilla.com/report/index/bp-8c07c846-b2ed-4535-8db4-4ee072120720
https://crash-stats.mozilla.com/report/index/bp-f29a89ed-f8b1-4a62-ba3e-983e22120720
https://crash-stats.mozilla.com/report/index/bp-e16d2b91-0f7d-4e5a-9e25-255852120718
https://crash-stats.mozilla.com/report/index/bp-1226c709-5f87-41c6-95d3-4310d2120718
https://crash-stats.mozilla.com/report/index/bp-4de2a0da-dd36-4ec8-8e53-c42742120714
https://crash-stats.mozilla.com/report/index/bp-e16d2b91-0f7d-4e5a-9e25-255852120718
https://crash-stats.mozilla.com/report/index/bp-4de2a0da-dd36-4ec8-8e53-c42742120714
https://crash-stats.mozilla.com/report/index/bp-eac1c5a5-2dce-4415-b645-07a1f2120714
https://crash-stats.mozilla.com/report/index/bp-1ede5bd3-8c72-4362-8d79-4f29c2120714
https://crash-stats.mozilla.com/report/index/bp-d4fd5dae-dacd-45f8-9549-2c3702120722
https://crash-stats.mozilla.com/report/index/bp-ca510991-de29-44b3-be02-0255a2120722
https://crash-stats.mozilla.com/report/index/bp-8600c221-3fd3-4eaa-a5af-a602b2120722
With Hardware Accelaration in Flash turned off. Still crashing.

TS3276 Having trouble sending jpeg images as attachments in Mac email.....they go thru as images and PC users can't see the SAVE or QUICK LOOK boxes that Mac mail has. One friend scrolled over the image, right clicked on it and saved as a PNG file.

Having trouble sending jpeg images as attachments in Mac email.....they go thru as images and PC users can't see the SAVE or QUICK LOOK boxes that Mac mail has. One friend scrolled over the image, right clicked on it and saved as a PNG file.

Apple Mail isn't going to change the format of any of your attachments. it isn't going to corrupt them either.
Exchange is a transport protocol and server. The issue you describe is not related to Exchange.
There are many different versions of Microsoft Outlook in use and they all have e-mail bugs. Different versions have different bugs. Some Apple Mail hack to get around a bug in Outlook 2003 may cause the same message to be problematic in Outlook 2000. Fix them both and another issue will cause trouble in Outlook 2007. You can't fix this. Apple can't fix this. Microsoft can and has but that is irrelevant if your recipients are using older versions.
One specific problem is that Apple Mail always sends image attachments inline, as images, not as iconized files. You can change this with Attachment Tamer. Just be aware that use of this software will break other things such as Stationery. E-mail is just a disaster. To date, no one outside of Apple has ever implemented the e-mail standards from 1993. Apple has continually changed its e-mail software to be more compatible with the de-facto standards that Netscape and Microsoft have unilaterally defined and people documented as "standards" after the fact. The e-mail messages that Apple Mail sends are 100% correct and do not violate any of the original standards from 1993 or the Microsoft/Netscape modifications. The problem is entirely bugs and limitations in various versions of Outlook.

Pulseaudio and systemd --user: DBus scope issues?

Hi,
I have a multi-seat setup, so I need user-wide pulseaudio and whatnot. I'm trying to setup my boot through systemd --user.
Testing audio working apps are firefox, mpv, and mpd. The problem is:
- If I start pulseaudio and mpd manually everything is fine (no use of systemd)
- If I start pulseaudio through systemd no application has sound.
- If I start pulseaudio and mpd through systemd only mpd has sound.
raimundoyamtech~$ cat .config/systemd/user/pulseaudio.service
[Unit]
Description=PulseAudio Sound System
After=sound.target
[Service]
ExecStart=/usr/bin/pulseaudio
[Install]
WantedBy=multi-user.target
raimundoyamtech~$ cat .config/systemd/user/mpd.service
[Unit]
Description=Music Player Daemon
After=network.target sound.target
[Service]
ExecStart=/usr/bin/mpd %h/.config/mpd/mpd.conf --no-daemon
ExecStop=/usr/bin/mpd %h/.config/mpd/mpd.conf --kill
Restart=always
[Install]
WantedBy=multi-user.target
If I add BusName=org.pulseaudio.Server to the pulseaudio.service nothing changes.
Using pulseaudio's autospawn=yes leads to what seems to be same behaviour: mpd by systemd starts pulseaudio and is the only app with sound.
./config/pulse/client.conf only contains default-sink. Everything else is default.
Using alsa alone is not an option because of firefox.
Any thoughts?
EDIT:
raimundoyamtech~$ systemctl --version
systemd 208
+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ
raimundoyamtech~$ pulseaudio --version
pulseaudio 4.0
Last edited by Raimundo (2013-10-23 10:08:13)

ewaller wrote:
Please do not bump. I understand the frustration; really, I do. But, these are very active forums with some very good technical people lurking about. I guarantee your post had been read. I read it. I did not have an answer, as I have never seen that behavior afore. I am certain that was true for many other regulars.
In the future, you can bring focus to a thread by providing more information.. Tell us what you have tried, what you have read since the last post, etc. At least it gives the impression that you are working the problem rather than merely waiting for a response.
I don't know almost anything about systemd, especially because it changes so rapidly and documention is so scarce and outdated that either I read the whole documentantion for my version in hopes of finding my problem (something for which I do not have time) or post a topic.
I posted everything I touched regarding systemd since the installation of my system, that's all the relevant information I know I can give, so at this point I had no more info to give.
Actually posting a topic is really my last resort, it usually means that I have already tried everything I knew and I'm hopeless already.
raimundoyamtech~$ loginctl list-sessions
SESSION UID USER SEAT
2 1002 carla seat0
1 1000 raimundo seat0
2 sessions listed.
raimundoyamtech~$ loginctl show-session 1
Id=1
Timestamp=Tue 2013-10-29 12:33:47 WET
TimestampMonotonic=6670234
VTNr=1
TTY=tty1
Remote=no
Service=login
Scope=session-1.scope
Leader=1456
Audit=1
Type=tty
Class=user
Active=no <----- Is this what you are talking about?
State=online
IdleHint=yes
IdleSinceHint=1383050072367636
IdleSinceHintMonotonic=0
Name=raimundo
raimundoyamtech~$ loginctl show-session 2
Id=2
Timestamp=Tue 2013-10-29 12:33:47 WET
TimestampMonotonic=6667439
VTNr=2
TTY=tty2
Remote=no
Service=login
Scope=session-2.scope
Leader=1453
Audit=2
Type=tty
Class=user
Active=no <----- Is this what you are talking about?
State=online
IdleHint=yes
IdleSinceHint=1383050025387636
IdleSinceHintMonotonic=0
Name=carla
raimundoyamtech~$ loginctl show-session 3
Failed to issue method call: No such file or directory
What is an active session? Oo Never heard of it
I could start things. Pulseaudio started, so did mpd. I also have a /usr/lib/systemd/systemd --user process started for each user. I assumed this would be it since this
raimundoyamtech~$ systemctl --user
Failed to issue method call: Process /bin/false exited with status 1
always happens and I've read that systemctl --user is no longer required.
[EDIT]
Fixed it. Don't remember where I read that it wasn't required, just that it was in the same place I found someone else complaining about getting this error.
For anyone else encountering this: sed -i s/system-auth/system-login/g /etc/pam.d/systemd-user
and systemctl --user will work. Insults fly out to the one who wrote it wasn't required!
Still am not able to get an active session though
[/EDIT]
Why would there be a need for anything else? I'm gonna check on that. Thanks!
See, the bump worked ^^ but ok I'll try to refrain from doing that next time. Sorry.
Last edited by Raimundo (2013-10-29 16:27:55)

Robohelp 10 - where an I get some decent, helpful user documentation as a potential new user

I am running a trial version of Robohelp 10, with a view to buying it as the single-source authoring tool for a company I am working for as a contract technical author and consultant. However, the user documentation delivered with this product is very poor. It is missing a level of information - the 'overview' level that explains the steps required to actually set up a project and getting it to generate output in various formats.
The user guide I have gives lots and lots of detail about the individual features of the product, but has no explicit information about how they hang together to create output.
What I need is something that says 'First create a project, then create master pages. Then create your topics and (do this) to get them included in your generated output.' At the moment I have 422 pages of documentation, but am having to go scavenging for information on what I need to do to get it all to work together.
I have ordered “Adobe RoboHelp HTML 10: The Essentials” by Kevin Siegel but had to buy this off the US site, and it will take weeks to arrive. Can anybody out there direct me to a source that will give me the level of information I need before that, please? Thanks in advance!

Or one of the Goober Guides might help:
http://www.gooberguides.com/
The Quick Start Guide might be useful, even through it's only RH7 - the basic concepts should be the same and procedures should be fairly similar.

802.1x NAC and per-user ACLs

Can 802.1x NAC and per-user ACLs be used together on the same port? I know some of the NAC documentation says that 802.1x NAC does not support downloadable ACLs but it looks like it might be outdated and according to http://cisco.com/en/US/products/ps7077/products_configuration_guide_chapter09186a0080817284.html , it appears that there is not preventing this.
Also, when will URL redirection to a remediation server be supported with 802.1x NAC?

You just need to configure it differently on ACS. "Downloadable IP ACLs" used to be "Downloadable PIX ACLs" on ACS. It changed to "IP" when VPN concentrators started supporting this with ACLs too. You saw this with NAC, if I remember .. and EOU does it this way as well.
802.1X with per-user ACLs was already shipping at the time though (has been for some time) and the mechanism is opertionally the same .. just functionally different.
With per-user ACLs, you'd configure a VSA like:
ip:inacl#1=deny ip any host 10.1.8.3
ip:inacl#2=permit ip any any
The "downloadable IP ACL" config would look like:
deny ip any host 10.1.8.3
permit ip any any
In the end, both techniques use the same VSA. This VSA is 026\009\001. In "per-user-ACLs, there's no sort of handshake though to see if the ACL is already there, etc. It slaps the ACL on for you unconditionally as an authorization rule b/c you told it to. (hence the "ip:inacl" stuff above). With "downloadable", there's a handshake before actually applying the ACL .. to see if there's an earlier copy of the ACL, and it'll only update what changed, etc.
So, it really boils down to semantics. Both techniques work. AAA config is subtely different on the backend. Look for this to get consistently deployed soon, but in the meantime, it's still supported ;-).
Hope this helps,

'Standard Role' 'User' 'Business Partner' and 'Internet User'

hii
Currently I m working on E-Recruitment 6.0 BSP's..
Can somebody explain me....
1)
'Role' 'User' 'Business Partner' and 'Internet User'
Kindly help me undertand the relation between the above mentioned IDs and there creation
2)
I have created Business Partner(External Person) ID using BP(txn)...Kindly let me know how to create the 'Internet ID' and 'PW'
So that I can use it for HRRCF_StART_EXT (BSP)
kindly explian...or mail me any documention related to
E-recruitment to my id [email protected]
Looking for a immediate reply
Regards,
Raghav

Role - is the same as the concept of role in R3. SAP Delivers some pre confogured authorisation profiles for some standard roles.
Roles are assigned to user depending on the client's requirement.
Business Partner is the same as BP in CRM. basically, the following will be BPs in ur system:
Each independent user of the recruitment process - as BP Branch.
All third party recruitment vendors as BP Type Agency.
All employees will also be BP in the system.
All external applicants.
You can create internet user using the t code SU05. You can also use the R3 sytem user credentials to log on to the url application by configuring the system to use the SAP login. (this is done thru t code SICF)
Hope this helps.

Need User Documentation for Oracle Calendar 9.04

I Need User Documentation for Oracle Calendar 9.04 (which replaced Steltor Corporate Time product). I've searched all over this site and can only find server administration documentation.
I see lots of requests from other users for this documentation and no satisfactory answer. Could someone please provide proper documentation for this software?
Thank you.
Helen

Hi,
You can refer to the Oracle Calendar Resource Kit found here:
http://download-west.oracle.com/docs/html/B10894_01/mainpage.htm#1005552
Thanks,
Lily

Additional Belle User Documentation

Something this forum could benefit by, is a "page" of additional user documentation to help people who have upgraded to Nokia Belle. This would include tips, suggestions, solutions, all in one place and easy to find.
That's the purpose of this thread.
If you have someting to add, please post it in a single paragraph, under an appropriate heading. Someone can go through this thread every so often, and compile a listing of everything that has been added. As for people using this forum, they could copy it and email it if needed, or simply print it out as additional user documentation. Perhaps Nokia will even add it to the official documentation.

FOLDER VIEW FOR MESSAGES
For those who want folders view as default go to MENU -> MESSAGES -> OPTIONS (lower right corner) -> VIEW FOLDERS -> again OPTIONS (lower right corner) -> MESSAGE VIEW -> INBOX. That way all new messages will open in inbox and folders are visible by default.
HOW TO REINSTALL LOST APPS FROM BELLE UPGRADE
Connect the phone to your pc as mass memory. Then go to the folder "private" and search for *.sis files. Copy the files to a new folder on mass memory, disconnect the phone from pc and run the *.sis files in the new folder. The installation starts and you can see the name of the app. Press OK and the installation runs and everything is like before. The icons of the apps are in the menu and the game savings are also there.
(Please add other useful information to this thread, both for all of us to find, and hopefully for Nokia to provide as additional documentation.)

6921 Phone and Multiple Users

We are a school system deploying a new Unified Communications Manager with Unity Voicemail. We will be placing 6921 phones in our classrooms. Some of these clasrooms are shared by two teachers and the plan is to give each teacher a unique extension number and voicemail mailbox. In the shared rooms, this amounts to using both lines on the 6921 and having two mailboxes.
The system is not in and live yet, but we are trying to work through some of the issues we know we'll encounter. One problem that we are trying to solve is how to indicate the presence of new voicemail messages for each user in the room. We are hearing from our vendor that they do not know of a way to indicate message waiting for both lines on a 6921. Unfortunately they have no experience with the 6921 phones, so they are basing this on guesswork. They cannot verify this as their lab is running UCM 6.x. We are installing 7.1, but have rights to upgrade to 8.0 if necessary.
We are hoping that the phone can indicate distinct message waiting for each line in some fashion. The documentation seems to indicate that this might be possible. We are even OK if the message waiting indicator lights for a message in either mailbox and the users would need to pick up their line and check for a stutter dial tone, but we do not know if this will work either. What we want to avoid is a situation where only one (or neither) extension activates the message waiting indicator and one (or both) users would need to periodically check their voicemail mailbox, or pick up the phone to check for stutter dial tone.
Has anyone deployed 6921s in this fashion and know if there is a way to have distinct message waiting indicators for both lines on a 6921? If so, how does it work? Is it a distinct light, or a distinct message on the display?
Any help would be appreciated.
Thank you,
Mark

Hi Mark -
Here's something that might help you - http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/6921_6941_6961/8_0/english/user/guide/book/6921enu801.pdf
It is the Unified IP Phone Guide which discusses the 6921 phone. It discusses phone features that can be configured in CUCM for the phones - the two I think you are interested in: (1) Visual Message Waiting and (2) Audible Message Waiting. The AMWI is the stutter dial tone you referenced, heard when the user presses the line button to go off-hook. Although I don't have personal experience with the 69XX phone series yet, I do have experience with dual-line phones like the 794X. For your shared phone with two lines, both configured for a voicemail profile, here is something that will probably apply to the 6921: The Messages button on the phone is the voicemail speed-dial (Easy message access) for the primary line on the phone. For voicemail users on the second line, for the same functionality, users will press the second line to go off-hook and then press the Messages button. Unity voicemail will recognize the calling number as a subscriber and prompt for password/PIN. Also, check out the System Policy in CUCM for the directory number configuration, which allows the Visual MWI to be set for secondary lines (Light and prompt), otherwise the typical default is just to light and prompt for the primary line.
Sincerely,
Ginger

Diff bet multi user and single user installation

Hi,
what is the diff betweeen single user and multi user installation,please let me know advantages and disadvantages also .
Regards

Hi,
what is the diff betweeen single user and multi user installationSingle user installation is having one user who owns all the application/database tier files. When you do an installation, you run RapidWiz as this user.
Multi-user installation is having two different users (applmgr user who owns the application tier files, and oracle user who owns the database tier files). When you do the installation, you run RapidWiz as root user.
On Windows, you cannot have multi-user installation. So, the above is valid on Unix/Linux.
More details can be found in the Concept manual --> http://www.oracle.com/technology/documentation/applications.html
please let me know advantages and disadvantages also .I always prefer multi-user installation as you just source the application/env file in the user's profile (in the applmgr/oracle profile) and the file is sourced once you login as that user. For single user installation, you will have to be sure that you source the proper env file manually each time you want to switch between the application and the database (just imagine if you try to shutdown/startup the database after sourcing the application env file, or trying to use any database executable file like export/import/sqlplus ..etc, you will end up using the application tier executable files).
Regards,
Hussein

Policies and Excluding Users

I'm using Messenger 7.0.2 and have a pretty basic question (I hope). I have the following eDir structure
<Organization>
<School 1>
<Office>
<Staff>
<Students>
<School 2>
<Office>
<Staff>
<Students>
etc.
My LDAPContainer object looks at everything in the tree (O=organization).
I have a DefaultPolicy that permits Messenger Use
I have a DefaultScope profile that includes the entire tree (*,O=organization).
I'm attempting to exclude certain OUs from Messenger use. Toward that end, I've:
1. Created a second scope (e.g., *,OU=Students,OU=Site1,O=organization).
2. Created a second policy and left (and locked) the checkboxes to disable messenger.
3. I've set the "Scope Profile" attribute for the policy for the new scope.
4. I cycled the Messenger agents.
Needless to say it didn't work. When I look at one the "student" users and click the "Novell Messenger" tab, I get a message that there is not policy associated with the Messenger object. I checked the template object but there are no Messenger options. I know I can select a bunch of users, assign the policy, and then it'll work but I have over 10k accounts in 8 different OUs and would like a better option. The documentation says I can go to the "Used By" attribute of my student policy and add them there but that's pretty clunky and requires maintenance.
Any thoughts would be appreciated!

Well, it's not perfect but I found a solution using (of course) JRB Utilities. Here's the procedure i wrote up:
=================================
Disabling Novell Messenger for Students
Through the use of Messenger (NM) scopes and policies, Novell has a method for denying NM services to users (students, in our case). The application of the policy, however, is relatively arcane and not user friendly. Through JRB's setname, the policy assignment can be made to large numbers of users very easily. This procedure assumes a "no Messenger" policy already exists.
1. Create/export a list of users or OUs to which the policy should be assigned. The file should look similar to the following (this example encompasses all students):
..*.students.<School1>.<Organization>
..*.students.<School2>.<Organization>
..etc.
2. Run SetName to assign the policy to the user attribute:
Setname @<input file> /a=nnmPolicyDN .StudentPolicy.PolicyContainer.MessengerService.NM .GW.<Organization>
3. This can be verified on the Novell Messenger tab of the user objects.
>>> David Hickok<[email protected]> 3/30/2009 10:39 AM >>>
Correction, Messenger 2.0.2.
>>> David Hickok<[email protected]> 3/30/2009 10:35 AM >>>
I'm using Messenger 7.0.2 and have a pretty basic question (I hope). I have the following eDir structure
<Organization>
<School 1>
<Office>
<Staff>
<Students>
<School 2>
<Office>
<Staff>
<Students>
etc.
My LDAPContainer object looks at everything in the tree (O=organization).
I have a DefaultPolicy that permits Messenger Use
I have a DefaultScope profile that includes the entire tree (*,O=organization).
I'm attempting to exclude certain OUs from Messenger use. Toward that end, I've:
1. Created a second scope (e.g., *,OU=Students,OU=Site1,O=organization).
2. Created a second policy and left (and locked) the checkboxes to disable messenger.
3. I've set the "Scope Profile" attribute for the policy for the new scope.
4. I cycled the Messenger agents.
Needless to say it didn't work. When I look at one the "student" users and click the "Novell Messenger" tab, I get a message that there is not policy associated with the Messenger object. I checked the template object but there are no Messenger options. I know I can select a bunch of users, assign the policy, and then it'll work but I have over 10k accounts in 8 different OUs and would like a better option. The documentation says I can go to the "Used By" attribute of my student policy and add them there but that's pretty clunky and requires maintenance.
Any thoughts would be appreciated!

My lock screen just shows a black background and a User Name/Password dialog after opening the screen from sleep. How do I get it back to where it blurs my desktop image with the dialog and my account image displayed?

I'm not sure when it began, but now my Macbook Air only shows a black background and a User Name and Password dialog box when I wake it from sleep. It used to show my desktop background blurred with my user name and icon displayed with only a text field for entering my password. I'm currently using Yosemite (OS X 10.10.1) and all updates have been done. Any help or suggestions would be greatly appreciated as I know this isn't a real problem, just an annoyance since I couldn't find how to change it back in the System Preferences.

I just have to point out that after looking at a related post (https://discussions.apple.com/message/22661092#22661092), it brought to memory that my issue most certainly began happening after I added some DoD certificates to the keychain. This obviously has something to do with it, but it still leaves me wondering what actually causes this to happen. :/

Error while creating a workspace and workspace user

Hi Everyone
I have installed oracle 11.1.0.7 on our server and the os is windows server 2008. I tried creating a new workspace and workspace user using the repository assistant on the server itself i mean i am using OWB which comes along with the 11g database. It is installing 60% and at the end it gives me this error:
The warehouse builder workspace installation failed Java.Sql.SQLexception ora -00942 table or view does not exist
How can i deal with this error? any suggestions ?
Thanks & Regards
Subhasree

Hi everyone,
I got the same problem. It is very urgent to get an answer.
Thanks
Siegwin

CME and SRST user documentation

Similar Messages

Maybe you are looking for