Communication Channel RFC Sender getting error suddenly
Hello gurus,
I'd like to ask you about a problem, we have many interfaces from RFC to SOAP synchronous, the CC RFC sender, in an average of once per day, gets into red colour with this error:
Sender channel 'CC_RFC_SENDER_L0_MAESTROS' for party '', service 'BS_LD0_100'
Error can not instantiate RfcPool caused by:
com.sap.aii.adapter.rfc.RfcAdapterException: error
initializing RfcServerPool:com.sap.aii.adapter.rfc.core.repository.RfcRepositoryException:
can not connect to destination system due to: com.sap.mw.jco.JCO$Exception: (102) RFC_ERROR_COMMUNICATION:
Connect to SAP gateway failed
Connect_PM TYPE=A ASHOST=10.1.4.191 SYSNR=00 GWHOST=10.1.4.191 GWSERV=sapgw00 PCS=1
LOCATION CPIC (TCP/IP) on local host with Unicode
ERROR partner 'XX.X.X.XXX:sapgw00' not reached
TIME Thu May 27 03:56:04 201
RELEASE 711
COMPONENT NI (network interface)
VERSION 39
RC -10
MODULE nixxi.cpp
LINE 3151
DETAIL NiPConnect2: 10.1.4.191:3300
SYSTEM CALL connect
ERRNO 111
ERRNO TEXT Connection refused
COUNTER 5
I don't know the reason of this.. but simply just stopping and starting the CC it gets into green colour again..
Does anyone know how to solve this?
Regards,
Juan.
Hi,
This happens if the RFC connection pool is not instantiated or may be cache failed to auto-refresh....And manual restart of RFC channel resolves it.
Refer page 8 in the RFC troubleshooting guide.
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/f3f93ee7-0c01-0010-2593-d7c28b5377c2?quicklink=index&overridelayout=true
Thanks
Swarup
Similar Messages
-
Verify Sender System - Communication channel RFC sender
Dear all,
We would like to select the option "Verify sender system" in our communication channel, RFC sender.
Do you know the correct parameters that we need to set? SYS-ID, CLIENT?
It would be nice to have an example.
Our PI version: PI7.11
Thanks you very much in advance.
Best Regards,
Olivier VanderperreFor non-SAP systems we do not set these parameters.....we do not check this option Verify Sender System
Is it to trust other non SAP systems
actually we do not set this option for non-SAP system becuase it is not possible to set the SID and Client details in the sender application....whereas when it is an SAP system we are able to set the details and hence verify them in XI/ PI.
Edited by: abhishek salvi on Mar 26, 2010 1:14 PM -
Is associating communication channel to sender agreement necessary
Hi,
Is it necessary to associate communication channel to sender agreement to pick the message from the specified source directoryHi Santhosh,
To pick the message from sender side , sender agreement should be required, thre are some cases where we dont need the sender agreement for IDoc Adapter and HTTP adapter. bcz these two adapters are resides on Integration server.
See the below link
http://help.sap.com/saphelp_nw04/helpdata/en/db/73e03fc2269615e10000000a155106/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/45/2c1640033ae569e10000000a155106/content.htm
Regards
Chilla -
XI: Sender JDBC Communication Channel is not getting picked the records
Hi All,
Here I 'm facing an Issue with my sender JDBC communication Channel. Previously it was working fine but It is not Picking the records from the JDBC table.
Communication Channel is in active mode only.
I have checked in RWB communication Channel monitoring there i didn't get any error or success messages but channel is showing healthy status only(Green)
But i had created the new communication channel..with the same parameters which are in the older communication channel.. and sender agreement level also i had changed.. so now new channel is working fine.... I didn't understand what is the problem with previous communication channel.
ThanksHi yadav,
do you have TWO CCs polling at the same time via JDBC?
This could be the problem --> a conflict between both CCs.
Switch off ONE CC:
Regards Mario -
FILE SENDER COMMUNICATION CHANNEL DOESN'T GET FILE
Hi,
I have create a new sender communication channel with ftp file configuration. Server parameter and source directory are correct.
I have also checked file and directory permission (chmod 777)
Poll interval is 600 secs.
There is no error in communication channel monitor (returned log: CC is correctly configured and started).
Process started every poll interval, but no file is picked up.
Why?
CarmeHi,
What type of file are you processing. Check whether the file type is binary or text mode.
Also check whether the file name you have specified in the CC and the exact file in the directory are the same.
Also check the file processing mode, whether it is read only, delete or in test mode.
If the file is in read only mode when the file first processed, then once the file was processed it would be in read only mode, so if you place the new file it should process, so try deleting the existing file in the directory and place a new file with exact file name along with the correct extension and try to process it.
Also I would suggest you check the exact file extension, by unchecking the radio button in the folder option under the menu tools> Folder options> view-->hide extension for file type.
Regards,
Nithiyanandam -
Hi Folks,
Am trying an RFC to SOAP sync interface.
Hav configured the Adapter, registered the program at PI, created RFC using registered server program.
When I trigger the FM as Call Function '..' DESTINATION <rfc dest> i get a system failure.
IN RWB Channel monitoring I see the error as "Error in processing caused by: com.sap.aii.adapter.rfc.afcommunication.RfcAFWException: senderAgreement not found: lookup of binding via CPA-cache failed for AdapterType RFC, AdapterNS http://sap.com/xi/XI/System, direction INBOUND, fromParty '*', fromService 'SAPECC_SHD', toParty '', toService '', interface 'ZBAPI_WEBSERVICE1', NS 'urn:sap-com:document:sap:rfc:functions' for channel 'CC_SAP_ZUMMATION_RFC_S' (channelId af2f451f1b473ac28063768416ba8a72)"
Have checked for errors such as * in sender agreement, header data in Receiver agreement note 730870..
Kindly guide if there is anything to be checked.Hi,
Clear the cache (SXI_CACHE) and stop and restart the RFC sender channel in RWB.
Cheers,
André
Edited by: André Schillack on Mar 30, 2010 5:09 PM -
Unable to create communication channel - RFC
Hi ,
I am trying to create communication channel automatically , when adding business systems from SLD to integration repository. I get the following error only for RFC
all other communication channel gets generated correctly.. Is there any thing i am missing.
HTTP communication channel GeneratedReceiverChannel_HTTP created
IDoc communication channel GeneratedReceiverChannel_IDoc created
XI communication channel GeneratedReceiverChannel_XI created
Unable to create communication channel: Unable to generate the communication channel (NWR_107, GeneratedReceiverChannel_RFC): com.sap.aii.utilxi.misc.api.ClientServerException
Thanks,
Ganesh RamPlease run transaction SLDCHECK. The connection to SLD might not be working properly.
Plus, in the business system you created, check if client number and all other parameters associated with SAP systems are valid.
Dmitriy -
Communication channel monitoring, adapter monitoring error
Hi ,
I am using SAP PI 7.0 with HP-UX.
Here we have 6 logical hosts in one physical host.
Physical host name is u2013 xyz
Integration server name u2013 sappid
The Central SLD: sappid
URL for sappid: sappid: 50300
When I monitoring RWB----
>communication channel monitoring, adapter monitoring, in Development system It's detecting another logical host ( like www://sapard:50300 ) and getting page cannot find error.
1.SLDCHECK
http://xyz:50300/sld
host name: xyz
port number: 50300
user : SLDDSUSER
2.SXMB_IFR
http://xyz:50300/rep/start/index.jsp
3.SMICM
icm/server_port_0 = PROT=HTTP,PORT=8003
icm/server_port_1 = PROT=SMTP,PORT=0
icm/HTTP/j2ee_0 = PREFIX=/,HOST=localhost,CONN=0-500,PORT=50300
icm/host_name_full = sappid
4. SLDAPICUST
SAP_CONFIG 1 xyz 50300 SLDDSUSER
5. SXMB_ADMIN
Role of Business System Integration Server
Corresponding Integ. Server http://sappid:8003/sap/xi/engine?type=entry
Integration Engine Configuration Data -> Check button
6.When I opened the http://xyz:50300/rep/start/index.jsp I got the
XI start page.
when I opened the http://sappid.AIG.com:50300/
the page not found issue, when I opened http://sappid:50300/ I got the
XI start page.
plz help me for this issue.
thanks in advance.
regards,
reddy.Hello,
I think the FQDN is not set properly.
Problem in the parameter
SMICM
icm/server_port_0 = PROT=HTTP,PORT=8003
icm/server_port_1 = PROT=SMTP,PORT=0
icm/HTTP/j2ee_0 = PREFIX=/,HOST=localhost,CONN=0-500,PORT=50300
*icm/host_name_full = sappid *
Replace this parameter in instance profile
icm/host_name_full = sappid.AIG.com
Then in the host entry of your server please add an entry
172.18.23.233(ip your ur Xi server) sappid.AIG.com
Then let us know the result.
Thanks and Regards
Vijay -
ORA-03113: end-of-file on communication channel & ORA-00600: internal error
Hi All,
I am testing my database which is already on 11gr1 working fine for application but after migration from 11gR1 to 11gR2 i am getting the below error while running application on a view:-
ORA-03113: end-of-file on communication channel
Process ID: 3280
Session ID: 35 Serial number: 11301
Above Error gets resolved after changing the order of underline tables and recreate But their is another error i am getting with same test case means select from a view
ORA-00600: internal error code, arguments: [kkqtSetOp.1], [], [], [], [], [],[], [], [], [], [], []
This view is complex and nested. But working fine in 10g 11gR1. Please help...
Edited by: 832546 on Feb 8, 2011 1:48 AMHi,
Above errors ORA-00600: internal error is resolved after i submit SR. They suggest to change parameter “_optimizer_join_factorization” to false.
But i am still facing with another error with view on oracle 11gr2
ORA-03113: end-of-file on communication channel...
Below is the work around i done for "ORA-03113: end-of-file on communication channel"
Join Condition for view is
t1.VERSION=t2.VERSION
and t1."PLAN"=t2.BASELINE_PLAN_ID
and t1.PLAN_VERSION=t2.BASELINE_PLAN_VERSION
If i run by just removing any one of above join condition is works fine but since i dont know business logic so i come up with solution below
1. create table t111 as select * from t1;
2. rename table t1 to abc
3. rename t111 to t1
Now it is starts working.
I don't know what had happen but i find workaround not solution.
If somebody suggest the solution and reason why this happening highly appreciated.
Please Help....
Edited by: 832546 on Feb 14, 2011 3:24 AM -
Communication Channels : Receiver, Sender ?
Hi all,
sometimes I'm confusing a receiver or a sender communication channel. I was told to use receiver when XI receives, and sender when XI sends. But it's not so clear.
Does anyone have some tips ?
Thx to all.Hi Elliot,
You use the Sender for the system that sends the message, system that execute the message, and receiver in system that receive the data.
for example.
I have a ECC with RFC with developer the purchase order, and this PO is input the legacy system.
The ECC is Sender and Legacy system is receiver.
when I create the Interface Message, I choose the Inbound and Outbound message, and Sync or Async message.
Inbound or Outbound I See by Legacy system.
When OUT to the Legacy, the message is Outbound.
When IN to the Legacy, the message is Inbound.
When I need to the response, I use the Sync message.
When I don´t need the response, I use the Async Message.
For example.
ECC/RFC -> XI -> LEGACY
the init of the message is in ECC, I executed the RFC, and the data input the LEGACY.
I Need a communication channel SENDER (RFC Adapter).
I Need a communication channel RECEIVER (JDBC Adapter - for example).
and the interface message, the message is INBOUND Async. -
Configuration Communication channel File Sender Structure
Hello all,
I've a problem with configuration communication channel. My communication channel must be processed the following input structure:
H
HL00000015......
T.....
T.....
D....
HL...
T....
D....
R....
The first field is TYPE, it is my key value.
HEADER.keyFieldValue H
headerline.keyFieldValue HL
line.keyFieldValue T
detail.keyFieldValue D
TOTAL.keyFieldValue R
Recordset Name: file
Recordset Structure:HEADER,1,headerline,,line,,detail,*,TOTAL1
Recordset Sequence: Variable
Recordset per Message *
Key File Name TYPE
I'd like that my structure will be the following, but i don't know if is it possible, because i haven't got any line for item tag.
<file>
<HEADER>
<id>H</id>
</HEADER>
<item>
<headerline>
<id>HL</id>
<num></num>
<...></...>
</headerline>
<line>
<id>T</id>
<...></...>
</line>
<line>
<id>T</id>
<...></...>
</line>
<detail>
<id>D</id>
<...></...>
</detail>
</item>
<item>
<headerline>
<id>HL</id>
<num></num>
<...></...>
</headerline>
<line>
<id>T</id>
<...></...>
</line>
<detail>
<id>D</id>
<...></...>
</detail>
</item>
<TOTAL>
<id>R</id>
</TOTAL>
</file>
is it possible to do? How?
Thanks in advanced.
Regards,
GemmaHi ,
I think its better idea to give you some more links in addition to above post and let youtry to achieve it instead of giving the direct solution.
File Receiver with Content Conversion
/people/arpit.seth/blog/2005/06/02/file-receiver-with-content-conversion
Configuring the Receiver File/FTP Adapter
http://help.sap.com/saphelp_nw04/helpdata/en/95/bb623c6369f454e10000000a114084/frameset.htm
File content conversion sites
/people/venkat.donela/blog/2005/03/02/introduction-to-simplefile-xi-filescenario-and-complete-walk-through-for-starterspart1
/people/venkat.donela/blog/2005/03/03/introduction-to-simple-file-xi-filescenario-and-complete-walk-through-for-starterspart2
/people/arpit.seth/blog/2005/06/02/file-receiver-with-content-conversion
/people/anish.abraham2/blog/2005/06/08/content-conversion-patternrandom-content-in-input-file
/people/shabarish.vijayakumar/blog/2005/08/17/nab-the-tab-file-adapter
/people/venkat.donela/blog/2005/03/02/introduction-to-simplefile-xi-filescenario-and-complete-walk-through-for-starterspart1
/people/venkat.donela/blog/2005/03/03/introduction-to-simple-file-xi-filescenario-and-complete-walk-through-for-starterspart2
/people/venkat.donela/blog/2005/06/08/how-to-send-a-flat-file-with-various-field-lengths-and-variable-substructures-to-xi-30
/people/anish.abraham2/blog/2005/06/08/content-conversion-patternrandom-content-in-input-file
/people/shabarish.vijayakumar/blog/2005/08/17/nab-the-tab-file-adapter
/people/jeyakumar.muthu2/blog/2005/11/29/file-content-conversion-for-unequal-number-of-columns
/people/shabarish.vijayakumar/blog/2006/02/27/content-conversion-the-key-field-problem
/people/michal.krawczyk2/blog/2004/12/15/how-to-send-a-flat-file-with-fixed-lengths-to-xi-30-using-a-central-file-adapter
/people/arpit.seth/blog/2005/06/02/file-receiver-with-content-conversion
http://help.sap.com/saphelp_nw04/helpdata/en/d2/bab440c97f3716e10000000a155106/content.htm
Please see the below links for file content conversion..
/people/michal.krawczyk2/blog/2004/12/15/how-to-send-a-flat-file-with-fixed-lengths-to-xi-30-using-a-central-file-adapter - FCC
/people/michal.krawczyk2/blog/2004/12/15/how-to-send-a-flat-file-with-fixed-lengths-to-xi-30-using-a-central-file-adapter - FCC
File Content Conversion for Unequal Number of Columns
/people/jeyakumar.muthu2/blog/2005/11/29/file-content-conversion-for-unequal-number-of-columns - FCC
Content Conversion (Pattern/Random content in input file)
/people/anish.abraham2/blog/2005/06/08/content-conversion-patternrandom-content-in-input-file - FCC
/people/harrison.holland5/blog/2006/12/20/xi-configuration-for-mdm-integration--sample-scenario - FCC - MDM
XI in the role of a FTP
/people/shabarish.vijayakumar/blog/2006/04/03/xi-in-the-role-of-a-ftp - FCC
File to R/3 via ABAP Proxy
/people/prateek.shah/blog/2005/06/14/file-to-r3-via-abap-proxy - FCC
/people/mickael.huchet/blog/2006/09/18/xipi-how-to-exclude-files-in-a-sender-file-adapter - EOIO - File
http://help.sap.com/saphelp_nw04/helpdata/en/ee/c9f0b4925af54cb17c454788d8e466/frameset.htm - cc
http://help.sap.com/saphelp_erp2005vp/helpdata/en/95/bb623c6369f454e10000000a114084/content.htm - fcc cOUNTER
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/da1e7c16-0c01-0010-278a-eaed5eae5a5f - conversion agent
If still there is problem let us know so here the XI experties will definately add the solution for your query.
Thanks
swarup. -
Message Interface and Communication Channel are not getting in RW B
Hi
I have created a sceario in which i have created following things
2 - External Definition of Same XSD
2 - Data Types
2 - Message Types
4 - Message Interfaces
2 - XSLT mappings
2 - Interface Mapping
I have created on two scenario objects in XI ID.
But In RWB i can see only one sceario message interfaces and communication channels but the for other scenario MIs and Communication channels are not visible in RWB
I have created all the things in only one Namespace.
What could be the problem .please help me
RegardsHi,
Have you activated it?
Can you see it in SXI_CACHE?
If one is no please run report SAI_CACHE_REFRESH
Kind regards,
Wojciech -
RFC Sender Adapter error " Call to messaging failed"
Hi,
I have been trying the RFC-> XI->File scenario.When I execute RFC using se37 transaction
on R/3 box,it gives the error " Call to messaging failed:
com.sap.aii.af.ra.ms.api.DeliveryException".
I have looked at msg in XI server using SXMB_Moni transaction.I found that,program is unable
to find the interface mapping function (Mapping between RFC and Inbound interface).
I have done the following settings:
For Sender :
1.RFC is being used as outbound Interface.
2.Imported RFC from R/3.
3. The R/3 functionality is to retrieve records.
For Receiver:
1.Defined Inbound ,Async. Interface.
2.Defined Data Type and Msg type
3.Defined Fault Message type
Mappings:
1. Message Mapping is defined for Inbound Message(From RFC) and Outbound Message
2. Source Interface(ZRFC) and target Interface(Inbound Interface) mapping is defined.In this mapping I am unbale to defined Mapping for Response and Fault.I have just deifned for Request as tabs are not gettting enabled after click of 'Read Interface'.
All necessary configurations have been done in Intergration Directory.
I am getting XML message at receiver at without data where rfc retireves two records.Why this is not being done?
As there is no mapping for Fault message of Inbound interface with RFC interface,I think mapping no found error is coming.
PS. I have not done the message mapping between ZRFC.Response and Inbound Message.
Please comment,where I have gone wrong.
Thanks & Regards,
HImanshuHi,
I don't know if the info below will solve your problem. Your scenario is an asynch scenario, therefore, the RFC must be executed as a qRFC. SE37 executes the RFC as synch.
To execute the RFC as asynch, you must tested with a report (se38):
The RFC must be executed as a qRFC.
data: DEST LIKE RFCDES-RFCDEST VALUE 'MY_RFC_DEST'.
CALL RFC
IN BACKGROUND TASK
DESTINATION DEST
EXPORTING
COMMIT WORK.
The COMMIT WORK is required to send the RFC.
Regards,
Bill -
Can't send, get error message 5.7.1
Here is the complete message:
An error occurred while sending mail. The mail server responded: 5.7.1 [address] Relay access denied. Please check the message recipient [address] and try again
Using Outlook with same server settings, messages go through. If I resend multiple times from Thunderbird the message goes through. If I move the message to draft, and then check the isp's webmail, the message has been received by my isp and is in the proper webmail draft folder. Last night I had the same issues on my home computer (I'm currently at work).
Any help?The 'Relay access denied' error indicates your email provider is different to your ISP.
Can you post your Troubleshooting Information?<br>
Help - Troubleshooting Information
What is your ISP? -
I am using Outlook for Mac on my MacBook Pro. All was working well until I upgraded to OS X Mountain Lion (10.8.2). Since the upgrade, some (not all) of my incoming email messages are bounced back to the sender with the message: ....Status: 5.5.0....Diagnostic-Code: smtp; 250 OK. What can I do to resume reception of all of my email?
I am using Outlook for Mac on my MacBook Pro. All was working well until I upgraded to OS X Mountain Lion (10.8.2). Since the upgrade, some (not all) of my incoming email messages are bounced back to the sender with the message: ....Status: 5.5.0....Diagnostic-Code: smtp; 250 OK. What can I do to resume reception of all of my email?
Maybe you are looking for
-
Any Prerequisites to run panels in CS4?
I have developed a set of actions and then used the Configurator to develop two panels that front-end the actions. The panels simply call the actions and nothing more. I have begun distributing these in a set that is installed with two install routi
-
Hi, we are migrating a jsp based website to portal. There is a web page in which it has a image and a list of "short descriptions of company stories" scrolling on the right hand side. They did it by HTML, JSP and talking to database and storing those
-
My ipod don't start. Screen show Apple logo and flashes. I try to restart holding main button and select button and nothing happen. Thanks
-
Removing Currency Symbol in PLD & Dot Matrix printer issue
Hi All I need to know if its possible to remove the currency sysmbol on your print out. I'm printing on a pre-printed stationery and the currency symbol makes the lines to overlap. Aonther question is , which font format can you select to for printin
-
Hi, I am trying to connect to Oracle 11g database via php. The code that I got from wiki.oracle.com is not working: $conn = oci_connect("/", "", $db, null, OCI_CRED_EXT); I did not get any error but it did not connect to the database either. Any help