Conference bridging between VoIP and GSM calls

Hello, Can E61/E62/E50/E70 do conference between one call that's running on GSM and second call running through SIP client on VoIP? Thanks, Bilal

I tried to connect the GSM call to VOIP call on E72, but it has not happened.
I presume this may be the case, also there may be a solution for this.
VOIP Connection:
For VOIP calls the network uses an existing external IP address to transfer the information from the a server. The information received vide VOIP shall be transformed into voice which enables us to here the data conveyed by the server.
GSM Connection:
For GSM calls the network uses the intermediate service provider slot to convey the information as a signal throught the network. The signals are the direct output we hear as sound.
By my observation, in my mobile, the two network actions (VOIP and GSM) can be performed instantaneously or simultaneously.
The mobile needs a medium to convert either the GSM output signal (audio) to Internet packet data (bytes) and the VOIP software installed in mobile should recognize the same audio as an input and allow for a conference call.
or
VOIP call get converted into GSM signal.

Similar Messages

Configuring JMS Bridges between COM and SOM

Hi,
We started working on OSM 7.0.2 and I have a question about the configuration of JMS Bridges between COM and SOM.
When COM and SOM Cartridges are installed in the same OSM instance on non-cluster env., it is mandatory to configure JMS Bridges between COM and SOM?
If it is case, could you please detail the procedure to follow?
In the document called "Application Integration Architecture Order-to-Activate Cartridge Guide Release 7.0.2 E18005-01" it is not obvious to understand. If you have a look in the table 2-1 page 2-15, I don't see all the mandatory field values to create a new destination bridges (for instance, what is the value of destination JNDI name?). Does anyone configure this part in the setting up OSM to the Order-to-Activate Solution?
Best regards.

The COM-SOM bridge is only required when COM and SOM are deployed on separate osm server instances and AIA Emulators are deployed (on both) for development/demo/quick testing purposes.
In QA/SIT/PRODUCTION environments, OSM should be integrated via AIA, this means that all participant applications ( CRM , OSM-COM, OMS-SOM, BRM ) should be using queue bridges (or SAF in 7.0.3)

Weblogic JMS bridge between Weblogic and oracle Advanced Queue

Hi,
We are facing some issues when we are trying to integrate with Oracle AQ JMS through Weblogic.
We have configured a Foreign AQ server which points to the oracle Advanced Queue and we are trying to create a Weblogic JMS bridge between AQ and weblogic. The bridge works perfectly if create the connection factories and bridge destinations with NonTX mode. The issue is with XA mode. Also we have deployed the Resource adaper for XAResource to use XA transactions.
No help is available for the exception on google too :)
Following is the exception we are getting.
<An error occurred in bridge "aqjmsbridge" during the transfer of messages (javax.resource.ResourceException: Failed to setup the Resource Adapter Connection for enlistment in the transaction, Pool = 'eis/jms/WLSConnectionFactoryJNDIXA', javax.transaction.SystemException: start() failed on resource 'eis/jms/WLSConnectionFactoryJNDIXA': XA_OK
javax.transaction.xa.XAException: method start should not be called on weblogic.transaction.internal.IgnoreXAResource
at weblogic.jms.foreign.IgnoreXAResourceImpl.start(ForeignAQIntegration.java:260)
at weblogic.connector.security.layer.AdapterLayer.start(AdapterLayer.java:513)
at weblogic.connector.transaction.outbound.XAWrapper.start(XAWrapper.java:466)
at weblogic.transaction.internal.XAServerResourceInfo.start(XAServerResourceInfo.java:1184)
at weblogic.transaction.internal.XAServerResourceInfo.xaStart(XAServerResourceInfo.java:1117)
at weblogic.transaction.internal.XAServerResourceInfo.enlist(XAServerResourceInfo.java:275)
at weblogic.transaction.internal.ServerTransactionImpl.enlistResource(ServerTransactionImpl.java:516)
at weblogic.transaction.internal.ServerTransactionImpl.enlistResource(ServerTransactionImpl.java:443)
at weblogic.connector.transaction.outbound.XATxConnectionHandler.enListResource(XATxConnectionHandler.java:118)
at weblogic.connector.outbound.ConnectionWrapper.invoke(ConnectionWrapper.java:218)
at $Proxy59.receive(Unknown Source)
at weblogic.jms.bridge.internal.MessagingBridge.processMessages(MessagingBridge.java:1427)
at weblogic.jms.bridge.internal.MessagingBridge.beginForwarding(MessagingBridge.java:1002)
at weblogic.jms.bridge.internal.MessagingBridge.run(MessagingBridge.java:1079)
at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTuningWorkManagerImpl.java:516)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)
.).>
Will appriciate any help for the above.
Thanks and Regards,
Navin

Maybe this if of any help:
- Re: Help with creating AQ JMS
or
- Re: AQ Weblogic integration - JMS-107: Operation not allowed on Connection

3 iphones in household.All use same apple ID.But all contacts get mixed between phones and facetime calls come in from other contacts.Ho can we change this so our phone information isn't visible to each other?

3 iphones in household.All use same apple ID.But all contacts get mixed between phones and facetime calls come in from other contacts.How can we change this so our phone information isn't visible to each other?

Use separate Apple IDs for each family member and use Family Sharing features of those things (if any) that you do want to share. https://www.apple.com/ios/whats-new/family-sharing/

Bridge between DropTarget and TransferHandler

Bridge between DropTarget and TransferHandler
Hypothetically, what if you have:
1) old code which uses a DropTarget to tie together a JEditorPane and a DropTargetListener
2) the desire to set on newish GUI code a TransferHandler. It�s a custom GUI TreeTable component that I want to be the source of the data only (COPY).
When I tried to mock something up and drag something from the new GUI to the old GUI, I did not see a Transferable set in the DropTargetDropEvent of the drop method
Thoughts? Has anyone ever done such a thing before? Google did not reveal much.
The mock up code I have is intertwined with the system so I cannot share it.
Thanks.

Try setting a breakpoint in the listener method and see if the event is recognised.

Nd help configuring JMS Bridges between COM and SOM

We skip the JMS Bridge between SOM and COM because we deploy the O2A cartridge using the:
- When Central Order Management and Service Order Management Exist in the Same
OSM Instance in a Non-Cluster Environment.
- Customer and Service Order Management in the Same OSM Instance
"Deploy the following cartridges through Design Studio for the simple fulfillment
topology"
Now what happening is: the flow of the order taking time before it was completed or need manually submit the task using oms-automation user.
But even with the above work around we cannot see the billing data in BRM.
UpdateSalesOrderSiebelCommsProvABCSImpl (v. 1.0) this is the last BPEL process we see in BPEL.
FulfillBillingFunction.BRM-ALL.BundleGranularity.FulfillBillingSignificantUpdates is the last Activity we can see in osmwebui if not manually update the task.
Then ProvisionOrderSIResponseTask is the current task in osm task web client where order state is In-Progress.
With that it seems the SOM is not processing.
Do you have any idea why we can't complete the order and see the billing data in BRM?
Is'it the COM and SOM not properly configured, or have some issue with other application(RODOD)?
Thanks,
Ace

Hi All,
This issue already resolve by configuring the routing in AIA.

Wireless Bridge between WAG120N and E1500

I have my internet coming into my WAG120N and going out wirelessly. I want to setup a wireless bridge between this and an E1500, so I can connect my TV to the E1500 (via an ethernet cable) and have it access the internet. Unfortunatly I can run a cable from the WAG120N to where the TV is. So it I can get the E1500 wirelessly bridged to the WAG120N, I hope I can get around this issue.
I have updated the firmware ont he E1500 to get Bridging support, but from what I can tell it only provides bridging via an ethernet cable. Is there away to bridge wirelessly?
Cheers
Mike
Solved!
Go to Solution.

1. Linksys wireless routers don't support wireless bridging.
2. Either install 3rd party firmware like dd-wrt or tomato or buy a dedicated wireless bridge and connect the E1500 to the bridge. That way you can also use the wireless in the E1500 for wireless connections.
3. Otherwise check power line ethernet. That's often a better and more reliable solution.

Switch between CDMA and GSM Iphone 5

Hi,
I am wondering on the Verizon Iphone 5, can you switch between CDMA and GSM via a setting or is it still like the iphone 4s where you have to remove the sim card to switch back to CDMA?
Thanks.

A SOLUTION: cut another corner and insert the nano-SIM upside-down, and keep a SIM card ejection tool on your key ring or tape one to your phone's case or both.
Adam, and anyone else who like us, was hoping that there were a software based method that would allow iPhone 5 users the option of toggling between Verizon (or other CDMA carrier) and whatever other SIM Card based GSM carrier we have inserted/installed into our SIM tray.
For myself, I have a SIM card with the "Minutes" type of plan, specifically the minutes plan that gives 2000 minutes for $100, which is good for one year. This is my backup network.
Since I do not need a SIM for the CDMA network that I use as my primary network, my SIM slot is empty (I am not running LTE, only 3G).
So, in order to be able to switch my handset from one carrier to the other, which would be most helpful in the event of a system failure on my primary carrier I can switch over to my "backup/gsm network; it would be very, very nice to be able to toggle between the two networks, (like in the old days where we could simply select either the 'A' {non-wireline} or the 'B' {wireline} carrier/network) by simply pressing a couple-few buttons. It is funny to me to actually realize my old "Brick" phone actually had a feature lacking on my iPhone 5.
This would have been great during hurricane Sandy when my Verizon service was (literally) dead in the water for several days. And, there is always the possibility of a cell site going down on the primary network, again.

Jabber and Gsm Call status

Is it possible to automatically update presence status to busy in jabber mobile when the user is attending a gsm call?
I've been testing with jabber for iPhone and it doesn't work...

Single DN only I'm afraid. Multi-line is on the roadmap but I can't speak to a timeline.
Please remember to rate helpful responses and identify helpful or correct answers.

Workgroup Bridge between WRVS440n and WAP321

Hi, i am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.
First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference
I am stuck with this status on the WAP321:
Network Interface Status and Statistics VLAN ID Name (SSID)
WLAN0UPSTRM Disconnected 1 myssid
WLAN0DWSTRM Up 1 myssid
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected
What am i missing?

Hello Lars,
Just wanted to add a note to this as well. Pretty much the workgroup bridge is made to be used with other wireless devices that are not WAP121's and WAP321s. Cisco pretty much recommends to use WDS bridge if you have another WAP321 or WAP121.. if that is not the case then workgroup bridge is your other options. The admin guide should have some good documentation on this and also if you click on help in the GUI of the WAP321 it provides a lot of great information as well! It gives you recommended set up for this configuration.
Other than that you do not have to set up WDS on the WRVS4400n. As long as the SSID, wireless channel, wireless mode, wireless bandwidth and secuirty is the same on the WAP321 and the WRVS4400n this should work out just fine. Maybe have to power cycle the devices a couple times to get it to come up but I know I have gotten this to work between a RV220w and a WAP321... so I do not see why it shouldn't work between the WRVS4400n and the WAP321.
Hope that helps!
Thanks,
Clayton Sill

Problem with the voice volume between incoming and outgoing calls

Hi all.
I have a situation with volume calls.
1.- When the calls are originated in the PSTN to the IP Phones, the volume is ok in both sites.
2.- When the calls is originated in the IP Phones to the PSTN, the person in the PSTN listens very low.
I try to adjust the volume in the voice-port configuration, increasing the input and output db value, but not if I am doing it well or if I need adjust the configuration in other part.
The router 2801 have a CCME ver 4, this router is connected to PBX with a E1 and the PBX have the PSTN Digital trunks.
this is the voice router configuration:
voice-card 0
dsp services dspfarm
voice service voip
allow-connections h323 to h323
supplementary-service h450.12
controller E1 0/0/0
framing NO-CRC4
line-termination 75-ohm
ds0-group 0 timeslots 1-12 type e&m-immediate-start dtmf dnis
description to the PBX
voice-port 0/0/0:0
auto-cut-through
input gain 4
output attenuation 4
playout-delay nominal 200
playout-delay minimum low
bearer-cap Speech

Try using a negative value in the output attenuation setting. My understanding is that negative values in the the output attenuation increases the volume out to the PSTN. Make small adjustments as you increase the chance for echo. Positive values decrease the volume.
Larry

Bridge between wired and wireless

This is what I am hoping to accomplish
router *****wireless connection 802.11******wlan0 - laptop - eth0 --------Wired ethernet---------------- another host(s)
routers IP is 192.168.1.1
The "other host(s)" need to be able to pull information via dhcp from the router.
What I've tried so far
I've installed bridge-utils and enabled ip forwarding in /proc
brctl addbr br0
brctl addif br0 wlan0
brctl addif br0 eth0
This is where I get lost. I think I need to manually configure wlan0 and eth0. In Ubuntu I think I remember setting br0 to bridge_ports in /etc/network.d/interfaces but I am not sure how to do this in Arch.
Any suggestions?
Thanks
band-aid
Ok I think I have been going about this all wrong, is it possible to do what I need to do using iptables masquerading?
Last edited by band-aid (2008-07-21 07:20:33)

You can use bridging OR ip masquerading - you don't need both. If you use bridging, wlan0 and eth0 join the bridge, which then gets its own virtual interface br0. This is the interface that gets an IP address, so that the laptop can continue to function normally. In this scenario, everything is on single subnet, and no ip forwarding or routing manipulation is required.
If you use IP masquerading, you're basically setting up NAT (Network Address Translation). The router and wlan0 are on one subnet, eth0 and the other hosts(s) are on another, and the laptop functions as the router between the two - as well as doing its normal laptop-y things, of course.
There are probably various pros and cons either way - one that occurs to me now is that the IP masquerade option will probably leave you with a double-NAT setup, because your existing router is most likely doing NAT already. This may or may not be a problem for you - depends really on the kind of network apps you will be running. Personally, I prefer bridging in this kind of situation, just because I find it simpler.

Wireless bridge between E4200 and WAG320N - Assistance required.

Hi,
As indicated on the title, I have both WAG320N and E4200, they are currently linked (wired) together as a bridge (it is not ideal or necessary, but lets move pass this point) and is working fine. But I'd like to place the E4200 on a floor above (which cabling is not an option) and is wondering how the two units can be bridged wirelessly while status quo on everything else.
Thank you in advance for your assistance.

You would have to use a 3rd part firmware (preferrably DD-WRT). Then you can set up the router as a bridge client (linked wirelessly and usable lan ports) or a repeater bridge so that the E4200 can act as a repeater, switch, and be bridged to the primary router.
I don't work for Cisco. I'm just here to help.

Wireless bridge Between WRT400 and WRT160n v3

Hello.
I have 2 routers WRT400 & WRT160n v3
The WRT400N is conncted to a DSL modem and providing network access to the house.
I setup WEP security on both of the bands (5Ghz & 2.4Ghz).
I'm looking to setup the WRT160n v3 in another room and set it as an "Access point" to connect to the WRT400 and provide wired connection to other network devices in the other room, how do I connect both of the routers? [or switch the WRT160n v3 to access point mode]

Welcome to the Cisco Home Community.
You might want to check this article from the Cisco KB.
Meanwhile, lets wait for the experts to fill in their suggestions.
The Search Function is your friend.... and Google too.
How to Secure your Network
How to Upgrade Routers Firmware
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
How to Hard Reset or 30/30/30 your Router

What file acts as bridge between Planning and relational data source?

Hi any one knows the answer plz give me reply ..

Hi,
Planning communicates to the relational data source through a number of Java classes using JDBC.
Business rules also use the hyperion RMI service to communicate to planning.
Cheers
John
http://john-goodwin.blogspot.com/

Conference bridging between VoIP and GSM calls

Similar Messages

Maybe you are looking for