Nd help configuring JMS Bridges between COM and SOM

We skip the JMS Bridge between SOM and COM because we deploy the O2A cartridge using the:
- When Central Order Management and Service Order Management Exist in the Same
OSM Instance in a Non-Cluster Environment.
- Customer and Service Order Management in the Same OSM Instance
"Deploy the following cartridges through Design Studio for the simple fulfillment
topology"
Now what happening is: the flow of the order taking time before it was completed or need manually submit the task using oms-automation user.
But even with the above work around we cannot see the billing data in BRM.
UpdateSalesOrderSiebelCommsProvABCSImpl (v. 1.0) this is the last BPEL process we see in BPEL.
FulfillBillingFunction.BRM-ALL.BundleGranularity.FulfillBillingSignificantUpdates is the last Activity we can see in osmwebui if not manually update the task.
Then ProvisionOrderSIResponseTask is the current task in osm task web client where order state is In-Progress.
With that it seems the SOM is not processing.
Do you have any idea why we can't complete the order and see the billing data in BRM?
Is'it the COM and SOM not properly configured, or have some issue with other application(RODOD)?
Thanks,
Ace

Hi All,
This issue already resolve by configuring the routing in AIA.

Similar Messages

Configuring JMS Bridges between COM and SOM

Hi,
We started working on OSM 7.0.2 and I have a question about the configuration of JMS Bridges between COM and SOM.
When COM and SOM Cartridges are installed in the same OSM instance on non-cluster env., it is mandatory to configure JMS Bridges between COM and SOM?
If it is case, could you please detail the procedure to follow?
In the document called "Application Integration Architecture Order-to-Activate Cartridge Guide Release 7.0.2 E18005-01" it is not obvious to understand. If you have a look in the table 2-1 page 2-15, I don't see all the mandatory field values to create a new destination bridges (for instance, what is the value of destination JNDI name?). Does anyone configure this part in the setting up OSM to the Order-to-Activate Solution?
Best regards.

The COM-SOM bridge is only required when COM and SOM are deployed on separate osm server instances and AIA Emulators are deployed (on both) for development/demo/quick testing purposes.
In QA/SIT/PRODUCTION environments, OSM should be integrated via AIA, this means that all participant applications ( CRM , OSM-COM, OMS-SOM, BRM ) should be using queue bridges (or SAF in 7.0.3)

Weblogic JMS bridge between Weblogic and oracle Advanced Queue

Hi,
We are facing some issues when we are trying to integrate with Oracle AQ JMS through Weblogic.
We have configured a Foreign AQ server which points to the oracle Advanced Queue and we are trying to create a Weblogic JMS bridge between AQ and weblogic. The bridge works perfectly if create the connection factories and bridge destinations with NonTX mode. The issue is with XA mode. Also we have deployed the Resource adaper for XAResource to use XA transactions.
No help is available for the exception on google too :)
Following is the exception we are getting.
<An error occurred in bridge "aqjmsbridge" during the transfer of messages (javax.resource.ResourceException: Failed to setup the Resource Adapter Connection for enlistment in the transaction, Pool = 'eis/jms/WLSConnectionFactoryJNDIXA', javax.transaction.SystemException: start() failed on resource 'eis/jms/WLSConnectionFactoryJNDIXA': XA_OK
javax.transaction.xa.XAException: method start should not be called on weblogic.transaction.internal.IgnoreXAResource
at weblogic.jms.foreign.IgnoreXAResourceImpl.start(ForeignAQIntegration.java:260)
at weblogic.connector.security.layer.AdapterLayer.start(AdapterLayer.java:513)
at weblogic.connector.transaction.outbound.XAWrapper.start(XAWrapper.java:466)
at weblogic.transaction.internal.XAServerResourceInfo.start(XAServerResourceInfo.java:1184)
at weblogic.transaction.internal.XAServerResourceInfo.xaStart(XAServerResourceInfo.java:1117)
at weblogic.transaction.internal.XAServerResourceInfo.enlist(XAServerResourceInfo.java:275)
at weblogic.transaction.internal.ServerTransactionImpl.enlistResource(ServerTransactionImpl.java:516)
at weblogic.transaction.internal.ServerTransactionImpl.enlistResource(ServerTransactionImpl.java:443)
at weblogic.connector.transaction.outbound.XATxConnectionHandler.enListResource(XATxConnectionHandler.java:118)
at weblogic.connector.outbound.ConnectionWrapper.invoke(ConnectionWrapper.java:218)
at $Proxy59.receive(Unknown Source)
at weblogic.jms.bridge.internal.MessagingBridge.processMessages(MessagingBridge.java:1427)
at weblogic.jms.bridge.internal.MessagingBridge.beginForwarding(MessagingBridge.java:1002)
at weblogic.jms.bridge.internal.MessagingBridge.run(MessagingBridge.java:1079)
at weblogic.work.SelfTuningWorkManagerImpl$WorkAdapterImpl.run(SelfTuningWorkManagerImpl.java:516)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)
.).>
Will appriciate any help for the above.
Thanks and Regards,
Navin

Maybe this if of any help:
- Re: Help with creating AQ JMS
or
- Re: AQ Weblogic integration - JMS-107: Operation not allowed on Connection

Bridge between DropTarget and TransferHandler

Bridge between DropTarget and TransferHandler
Hypothetically, what if you have:
1) old code which uses a DropTarget to tie together a JEditorPane and a DropTargetListener
2) the desire to set on newish GUI code a TransferHandler. It�s a custom GUI TreeTable component that I want to be the source of the data only (COPY).
When I tried to mock something up and drag something from the new GUI to the old GUI, I did not see a Transferable set in the DropTargetDropEvent of the drop method
Thoughts? Has anyone ever done such a thing before? Google did not reveal much.
The mock up code I have is intertwined with the system so I cannot share it.
Thanks.

Try setting a breakpoint in the listener method and see if the event is recognised.

I need help syncing my contacts between Outlook and iPhone using iTunes. I followed the steps given and ended up with just email addresses showing in my contacts even though I have phone numbers and snail mail in my Outlook Contacts. Using Windows 7

I need help syncing my contacts between Outlook and iPhone using iTunes. I used the knowldge document and set it up to transfer my Outlook contacts to the iphone using itunes.
In contacts on the iphone I only see the email addresses.
Yet in Outlook I have email, snail mail and phone numbers.
I followed the knowledge document from iphone.
I did it once, didn't work so deleted all the contacts from the phone and tried again. Same result. I have a PC using Windows 7 64 bit.

You can't access an Exchange account via ActiveSync with the Address Book and iCal on your Mac.
You can access a MM account with Outlook on your PC at work and keep your MM email account server stored mailboxes synced between your PC at work, your iPhone, and the MM "cloud". Not sure about syncing MM contact info and calendar events with Outlook at the same time with an Exchange account.
This will not provide for syncing your Exchange account contact info and calendar events with the Addresss Book and iCal on your Mac because the accounts are separate.
You can access an Exchange account and a MM account at the same time with the iPhone's mail client, and sync contact info and calendar events over the air with both accounts at the same time. You can view combined contact info or separately for each account, and the same for calendar events.

Wireless Bridge between WAG120N and E1500

I have my internet coming into my WAG120N and going out wirelessly. I want to setup a wireless bridge between this and an E1500, so I can connect my TV to the E1500 (via an ethernet cable) and have it access the internet. Unfortunatly I can run a cable from the WAG120N to where the TV is. So it I can get the E1500 wirelessly bridged to the WAG120N, I hope I can get around this issue.
I have updated the firmware ont he E1500 to get Bridging support, but from what I can tell it only provides bridging via an ethernet cable. Is there away to bridge wirelessly?
Cheers
Mike
Solved!
Go to Solution.

1. Linksys wireless routers don't support wireless bridging.
2. Either install 3rd party firmware like dd-wrt or tomato or buy a dedicated wireless bridge and connect the E1500 to the bridge. That way you can also use the wireless in the E1500 for wireless connections.
3. Otherwise check power line ethernet. That's often a better and more reliable solution.

HT201272 Help! i purchased a cd and some of the songs are incomplete, can i redownload & how???

Help! i purchased a cd and some of the songs are incomplete, can i redownload & how???

If you are in a country where re-downloading is possible (iTunes in the Cloud and iTunes Match Availability by Country - http://support.apple.com/kb/HT5085), delete the track and download again (Downloading [using iOS or computer] past purchases from the App Store, iBookstore, and iTunes Store - http://support.apple.com/kb/ht2519). See tips on downloading in https://discussions.apple.com/message/19097773
Select the store on the left side of iTunes.
Click on Purchased on the right side under Quick Links.
You can re-download your available previous purchases.
If you cannot download a second time, contact iTunes Store support staff through the report a problem links in your account history or,
iTunes Customer Service Contact - http://www.apple.com/support/itunes/contact.html > Get iTunes support via Express Lane > iTunes > iTunes Store

JMS Bridge Between HornetQ (on Jboss 5.1) and WebLogic 10.3

Greetings!
I'm trying to set up a bridge between HornetQ (JBoss 5.1) and WebLogic 10.3. The bridge should be set up on WebLogic. It'll read messages from queue on HornetQ and post them on WebLogic Queue.
Here are my preferences on Source Destination:
Adapter JNDI Name eis.jms.WLSConnectionFactoryJNDINoTx
Classpath: empty (?)
Connection URL: jnp://<hostName>:1099
Initial Context Factory: org.jnp.interfaces.NamingContextFactory
Connection Factory JNDI Name: /tp/ConnectionFactory
Connection JNDI Name: /etgreceiver/queue
Destination Type: Queue
User Name: guest
User Password: guest.
WebLogic prints a warning: <12.10.2010 18:25:40 MSD> <Warning> <Connector> <BEA-190032> << eis/jms/WLSConnectionFactoryJNDINoTX > resourceAllocationException thrown by resource adapter on call to ManagedConnectionFactory.createManagedConnection(): "javax.resource.ResourceException: ConnectionFactory: failed to get initial context (InitialContextFactory =org.jnp.interfaces.NamingContextFactory, url = jnp://AIskrich:11099, user name = guest) ">
I have no idea what the problem is, could anyone help?

Yes - I think "pre_classpath" is probably the right place to reference the non-WebLogic jars. That said, layered products like BPEL often provide tooling that simplifies messaging integration -- I assume some even help setup classpaths and may have their own recommended unique way to set them. So I recommend consulting your layered product's documentation and forums.
It looks like this posting already covers the needed HornetQ specific settings. If it turns out that you're still interested in working directly at the WebLogic layer instead of the BPEL layer, see the interop FAQ http://docs.oracle.com/cd/E21764_01/web.1111/e13727/interop.htm#JMSPG553 for a full treatment of WebLogic's built in JMS provider integration features.
HTH,
Tom

Configure a Bridge between Websphere MQ 6.0(MQSeries) and Weblogic9.2

Bridge between Websphere MQ 6.0(Previously MQSeries) and Weblogic 9.2
At Websphere MQ 6.0 side:
³ Create a folder by the name JNDI-Directory under C drive
³ Create the queue manager by using the command at the command prompt:
crtmqm testqmgr or you can create it by GUI also.
³ Start the queue manager: strmqm testqmgr. or you can start it by GUI also
³Define Local Queues in the newly created queue manager testqmgr by using GUI or by using Commands .Assume we have created a local queue by the name MyMDBQueue.
³ Create a file by the name MyAdmin.config,It¡¦s a configuration file under C:\Program Files\IBM\WebSphere MQ\Java\bin directory.
Now add the following entries into the config file
INITIAL_CONTEXT_FACTORY=com.sun.jndi.fscontext.RefFSContextFactory
PROVIDER_URL=file:/C:/JNDI-Directory
SECURITY_AUTHENTICATION=none
Without the above step also you can do that. How it means
You have a file called JMSAdmin.config under C:\Program Files\IBM\WebSphere MQ\Java\bin directory.jsut uncomment the above mentioned 3 properties and comment the remaing that¡¦s it.
Next run the below command
C:\Program Files\IBM\WebSphere MQ\Java\bin>JMSAdmin.bat ¡Vcfg MyAdmin.config
Once you run the above command you will see
this prompt InitCtx>.
Now your command prompt will stop at
InitCtx>
Just type the following commands
a) InitCtx> def xaqcf(SenderQCF) qmgr(testqmgr) press enter
b) InitCtx> def q(MyMDBQueue) qmgr(testqmgr) queue(MyMDBQueue) press enter
c) InitCtx> end press enter
At step a it will create a queue connection factory by the name SenderQCF UNDER QueueManager testqmgr
At step b it will create a queue by the name MyMDBQueue UNDER
QueueManager testqmgr
At step c Its ends the Context cration process
At Weblogic 9.2 side:
Go to your domain location lib folder i.e. In my system it¡¦s in C:\bea\user_projects\domains\bplus_domain\lib. Add the following jars in lib folder
1) com.ibm.mq.jar
2) com.ibm.mqjms.jar
3) commonservices.jar
4) connector.jar
5) dhbcore.jar
6) fscontext.jar
7) jms.jar
8) jta.jar
9) ldap.jar
10) postcard.jar
11) providerutil.jar
Now restart the weblogic server. now the server reads all the jars
Open console of weblogic9
Go to Services³Messaging³Bridges³Jms bridge destination. under this create new
jms bridge destination.
Source of jms bridge destination:
Adapter JNDI Name: eis.jms.WLSConnectionFactofyNoTX
Classpath:<optional>
Connection URL: file:/C:/JNDI-Directory
Initial Context Factory: com.sun.jndi.fscontext.RefFSContextFactory
Connection Factory JNDI Name: SenderQCF
Destination JNDI Name: MyMDBQueue
Destination Type:Queue
User Name: <optional>
User Password: <optional>
Confirm User Password: <optional>
Now activate the changes what you have made
Destination of jms bridge destination:
Adapter JNDI Name: eis.jms.WLSConnectionFactofyNoTX
Classpath: < optional>
Connection URL: t3://localhost:7001
Initial Context Factory: weblogic.jndi.WLInitialContextFactory
Connection Factory JNDI Name: ConnectionFactory1
Destination JNDI Name: ResponseQueue
Destination Type:Queue
User Name: < optional>
User Password: < optional>
Confirm User Password: < optional>
Now configure a new Bridge by using above configured two source and destination
jms bridge destinations
At source you have to select Other JMS.don¡¦t select Weblogic7 or Higher because the source of this bridge is WebsphreMQ, not weblogic
Now once again RESTART The weblogic9.2 serever and put one message on WebsphreMq queue and check whether it reaches the destination queue of weblogic
Enjoy the session

Is this working for you? What errors do you get in the logs (bam, EL)?

Help configuring jms over http?

I am looking to use jms over port 8080 to both send and receive soap messages. Does anyone know how to configure jms to do this? Any good documentation?
I am using Sun Application Server 8 Platform Edition.
Thanks.

Hi Rabbia,
This is not something which is defined by the JMS standard.
Each vendor has differing approaches to supporting HTTP/HTTPS. Some use proxy servlets in conjunction with web servers etc... Others don't support it at all.
Nirvana from my-channels supports the idea of adding multiple interfaces to a server. Each bound to a specific hostname and port and communicating over a specific protocol (e.g. HTTP or HTTPS). Using Nirvana you would simply add a HTTP interface which is bound to port 8080.
http://www.my-channels.com/developers/nirvana/FAQ/addingANetworkInterface.html
You would then configure your clients to point to that specific interface..
http://www.my-channels.com/developers/nirvana/examples/nJMS/jmsadmin_intro.html
Hope this helps.
Eddie McDaid
www.my-channels.com

I need help configuring three products: WRVS4400N, WAG325N and WVC200

Hello,
I want your help in three linksys products as mentioned below:
WAG325N ADSL2+ Router
WVC200 PTZ CAMERA
WRVS4400N VPN Router
The computer connections and configuration of above linksys products which I am working with and which are connected with the above three linksys products at present are as follows:
1) I have one server and one laptop.
2) Laptop has two wireless adapters which I use to connect to the routers.
3) The server is connected to the WRVS4400N Router through one of the four ethernet ports mentioned on backside of the WRVS4400N Router. The DHCP of this router is disabled by me and the router's default IP 192.168.1.1 was changed to 192.168.1.12
4) The WRVS4400N router is connected to the Wag325N router for internet access to the server and server is connected to WRVS4400N Router as mentioned in point number 3 above.
5) The WAG325N router is setup as per the instructions mentioned that came with the CD of this router. The only change that I have modified is the router's default IP. I have changed the default IP of WAG325N from 192.168.1.1 to 192.168.1.13 and DHCP is enabled on this router.
The help that I want is step by step as follows:
1) I want to configure the both routers in such a way so that I can access them from anywhere across the world i.e. remotely using internet.
2) I have WVC200 Camera which I setup according to instructions mentioned in the CD and also configured the DDNS service. But when the " RJ45 Cable is connected " to my WAG325N router and Camera, then only the camera works properly. What I want is that after the setup is completed, I want to remove the RJ45 Cable connected from my camera to router and use the camera wirelessly from any location within the range of my above mentioned WAG325N router. I need flexibility to use my camera without cable connections from any location and any rooms of my house. I also configured the port forwarding and DDNS properly. The only problem is that if I remove the Cable after the setup of camera is finished, then the camera access is not working on LAN or internet(through DDNS). Whereas the same works on LAN and internet using the DDNS service, when the cable is physically connected to the WAG325N router. Also I want one more thing additionally other then this. I want to use this camera wirelessly by configuring the port forwarding options on both routers at a same time(i.e. simultaneously at once on WRVS4400N and WAG325N).
3) Now as two DHCP cannot work at a same time and as my routers are connected with each other, So I have disabled the DHCP on WRVS4400N. Here I need help so that DHCP can be enabled on both at a same time. Because if the DHCP is not enabled on WRVS4400N then I have to give IP to the server which is connected with server. If I enable the DHCP then there are two DHCP's at a same time on same network and thus problems occurs in internet access to the server. So, what should I do in such a way so that I do not have to give any IP to my server and set it to automatic.
4) This question is just for my knowledge so that I can use the above mentioned linksys purchases upto full extent possible in future. I want to know what is VPN and how is it usefull? What is the difference between VPN and VPN tunnel? How can VPN be used to access all my network resources connected with my server in the above situation where my server is connected to WRVS4400N which in turn is connected to WAG325N?
Thanks !
Sincerely
Kalpesh Sharma
+91-79-25351208
+919227435453
Ahmedabad, India.

for question number 1:
you said that your main router is WAG325N, for you to remotely access the 2nd router is for you to forward the IP addr [192.168.1.12] on your first router and change its management port of your second router that is located on either the security tab or the administration tab on its User Interface
to access your first router open and Internet Explorer and enter
http://[public IP addr]:[management port]
the PUBLIC IP or INTERNET IP is located on the status page of your router
to access your second router just change the management port to
ex.
http://66.77.88.99:8080 first router
http://66.77.88.99:8081 second router
for question number 2:
make sure that you have configured all wireless settings on both your camera and your main router WAG235N, once done save settings and power down your camera and power it back up.
for question number 3:
for you to enable DHCP on both routers your connection can go like so...
from a regular port of your main router going to the INTERNET port of your second router [this way you can enable DHCP on both routers]. INTERNET is no problem, your cesond router will be able to get connection
for question number 4:
VPN - Virtual Private Network
VPN tunnel -is/are connections from router to router [gateway to gateway]
VPN is used to connect a diff network on a diff location for you to have access to the shared filed [it is like a file sharing through the internet]
for you to be able to use VPN tunnel you have to connect to a different VPN router on a diff location. In that way you can get access to the other network

Share Configuration Manager Entries between WebDynpro and EJB

Hi there,
I have an annoying problem: I would like to have a WebDynpro as full-blown configuration interface for my EJBs. As steted in the docu, it is not possible to share configurations between applications.
With EJB and Web Modules I would just place them in the same Enterprise Application. But I cannot as WebDynpro projects to enterprise applications (as far as I know).
Does anyone have a clou about I could manage this issue?
Thanks!
helge

Hi Maksim,
at the link you've provided it is described how to use the Configuration Manager within an EJB Module.
My Problem is that I want to use it from an WebDynpro Application. But there I don't have a META-INF\application-j2ee-engine.xm to configure the dependency.
This itself is not a problem since you can also access the Configuration Manager via JNDI.
My problem now is that the EJB Module (more precise the enterprise application where the EJB Module is included) needs to share the configurtion with the Dynpro. But vi JNDI you only get the ApplicationConfigurationManager - which is application specific.
So the question is how I could share the configuration between WebDynpro and EjbModule...
Regards,
helge

Help, about data synchronization between C++ and PHP API!

I use Berkeley DB XML as my Server's database, the client access the database via http by C++ API. I don't close the XmlManager and XmlContainer after read and write the database for better performance. However, I provide another way to manipulate the database via web by PHP. After I updated the data by PHP, I found that I couldn't catch the update.
If I close the XmlManager and XmlContainer after read and write the database every time, the problem disappeared. But I can't do that for performance.
How can I solve this problem? Thanks!

First of all, thank you for your attention.
I don't share the same environment for the two processes, but I seted the same configure flags on the environment. The flags as follows:
DB_CREATE|DB_INIT_LOCK|DB_INIT_LOG|DB_INIT_MPOOL|DB_INIT_TXN|DB_RECOVER;
The C++ code as follows:
//C++ code
UINT32 envFlags = DB_CREATE|DB_INIT_LOCK|DB_INIT_LOG|DB_INIT_MPOOL|DB_INIT_TXN|DB_RECOVER;
INT32 lRet = 0;
string ctnName = "rls_services.bdbxml";
string docName = "index.xml";
CHAR acXQuery[256] = {0};
CHAR acXmlDoc[] = "<test>C++ test</test>";
//from
DbEnv *pDbEnv = new DbEnv(0);
XmlManager *pxmlMgr = NULL;
pDbEnv->open("/usr/local/xdms", envFlags, 0);
pxmlMgr = new XmlManager(pDbEnv, DBXML_ADOPT_DBENV);
lRet = pxmlMgr->existsContainer(ctnName);
if(0 == lRet)
     pxmlMgr->createContainer(ctnName);
XmlContainer xmlCtn = pxmlMgr->openContainer(ctnName);
//to
// the code between 'from' and 'to' is a seperate function
XmlQueryContext xmlQC = pxmlMgr->createQueryContext();
XmlUpdateContext xmlUC = pxmlMgr->createUpdateContext();
sprintf(acXQuery, "doc(\"%s/%s\")", ctnName, docName);
XmlQueryExpression xmlQE = pxmlMgr->prepare(acXQuery, xmlQC);
XmlResults xmlResult = xmlQE.execute(xmlQC);
XmlDocument xmlDoc;
if (xmlResult.hasNext())
xmlDoc = xmlCtn.getDocument(docName);
xmlDoc.setContent(acXmlDoc);
xmlCtn.updateDocument(xmlDoc, xmlUC);
else
xmlDoc = pxmlMgr->createDocument();
xmlDoc.setName(docName);
xmlDoc.setContent(acXmlDoc);
xmlCtn.putDocument(xmlDoc, xmlUC);
// I don't close the Container and Manager for performance
The PHP code as follow:
<php?
$DB_DIR = "/usr/local/xdms";
$env = new Db4Env();
$enFlags = DB_CREATE|DB_INIT_LOCK|DB_INIT_LOG|DB_INIT_MPOOL|DB_INIT_TXN|DB_RECOVER;
$env->open("/usr/local/xdms", $enFlags, 0);
$xmlManager = new XmlManager($env, 0);
$ctnName = 'rls_services.bdbxml';
$docName = 'index.xml';
$docContent = '<test>PHP test</test>';
if (!$xmlManager->existsContainer($ctnName))
     return ;
$xmlCtn = $xmlManager->openContainer($ctnName);
$xmlQC = $xmlManager->createQueryContext();
$xmlUC = $xmlManager->createUpdateContext();
$acXQuery = "doc('".$ctnName.'/'.$docName."')";
$xmlQE = $xmlManager->prepare($acXQuery, $xmlQC);
$xmlResult = $xmlQE->execute($xmlQC);
if ($xmlResult->hasNext())
     $xmlDoc = $xmlCtn->getDocument($docName);
     $xmlDoc->setContent($docContent);
     $xmlCtn->updateDocument($xmlDoc, $xmlUC);
else
     $xmlDoc = $xmlManager->createDocument();
     $xmlDoc->setName($docName);
     $xmlDoc->setContent($docContent);
     $xmlCtn->putDocument($xmlDoc, $xmlUC);
unset($xmlDoc);
unset($xmlCtn);
?>
The code between 'from' and 'to' excute only one time when server start.
After the server started, I write data by PHP. I can read out the data that
writed by PHP just now, but I can't read out the data by C++ because I don't
close the XmlContainer and XmlManager.
After I restarted the server, I can readout the data by C++. But I can't
open and close database for each request for performance as a server.
what should I do ? Thank you!
Whether I express my question clearly or not?

Help me clarify: Difference between Joining and Extending Wireless Network

I've eventually figured out how to get my AirPort Express to allow my Mac Pro access to the internet Via Ethernet cable by joining an existing wireless network. What's the difference between that and extending it? By extending it I loose my ability to use the ethernet to connect to internet on my Mac Pro. Odd thing is though when I initially used AirPort Utility to set up my AirPort Express, I went through all the options to get it configured to access my existing network and I checked option to allow internet access through ethernet. All is well, but then I still don't have access to the internet through the ethernet and I noticed that the setting is on Extended. Just curious why it would give me the option to use the ethernet, set it on extended and not even work.

I've eventually figured out how to get my AirPort Express to allow my Mac Pro access to the internet Via Ethernet cable by joining an existing wireless network. What's the difference between that and extending it?
When "joining a network," the AirPort Express Base Station (AX) acts just like any other wireless client (laptop, desktop, printer, etc.) You would want to configure the AX to join a network when you only want to use it to share a USB printer and/or stream iTunes.
When "extending a network," the AX can perform as either a main, relay, or remote base station in a Wireless Distribution System (WDS). A WDS is primarily used to extend a network wirelessly.
By extending it I loose my ability to use the ethernet to connect to internet on my Mac Pro.
If the AX is configured as either a relay/remote base station in a WDS, you actually can use it's Ethernet port for Internet access. Of course, this relay/remote must be connected to a main base station, that itself, has Internet access.

Need help with Color Profiles between Photoshop and iPhoto

Hey guys, I'm a photographer and have always used Photoshop in comination with iPhoto. I am having great difficulty lately with color profiles randomly changing within albums of pictures. I need all of my images to be in sRGB, but some somehow end up in Adobe RGB. It seems to happen at random. Apple seems to think it's an Adobe problem. Adobe isn't sure what to do. Anybody aware of any known issues between CS5 and iPhoto using OS 10.8.4 with regard to color profiles and how to fix them?

SRiegel schrieb:
I don't know inkscape, but this article seems to indicate that is will support cmyk.
The article also says you need Scribus to then further process the SVG file.
@shaunamm You need to open the SVGin Illustrator, not place it. But I doubt that you will be able to get the effects in Illustrator.

Nd help configuring JMS Bridges between COM and SOM

Similar Messages

Maybe you are looking for