Config for using 1242 for site survey

Hello, i'm helping a coworker, we have a 1242 and would like to use it for a site survey, but we are not able to activate the radio using conf t it is in light weight, are we missing something? were can i find a config example to use for this purpose?

Hi Alfred,
Converting a Lightweight Access Point Back to Autonomous Mode
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 6 Disconnect power from the access point.
Step 7 Press and hold MODE while you reconnect power to the access point.
Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp161272
Hope this helps!
Rob

Similar Messages

How to config to use SPFILE for databse

Hi,
As I want to setup recovery settings, OEM gave a warning:
PFILE - The database is NOT using SPFILE. Changes to the initialization parameters will be LOST if the database is restarted.
How do I config to use SPFILE for databse rather than using control file I suppose? Thanks,

Thanks mdtaylor and abarra2000!
It works! because "sql>show parameter" gives spfile's location instead of null before the changing. I notice that original spfile in dbs\ directory is untouched. newly generated spfile is in database\ directory as "show parameter" indicated.
Thanks again,

I am trying to understand the licensing procedures for using tabKiller for 3.5.7 firefox. Who should I contact for this? I do not see any customer service phone number for Firefox

I am trying to understand the licensing procedures for using tabKiller for 3.5.7 firefox. Who should I contact for this? I do not have the customer service phone number for Firefox

Tab Killer is not created by Mozilla, it is created by a private individual who has made it available at no cost for other people to use.

What is the best tablet for using photoshop for professional editing??

Okay, I know Apple and their ipads are popular. But popularity is not what I'm looking for. I'm looking for compatibility, between photoshop and the tablet itself. I want to get over using the mouse for everything. I'm not quite sure if apple is the best choice. Or is it?
I'm very new to all this tablet stuff. lol Please advise
Oh my goodness. Is the Ipad not advanced enough for a full blown photoshop program?! I geuss I overestimated them. Goodness. It really is just a on the go kind of thing?.... Again. I'm new to this whole tablet thing. So if you guys know anything. Please advise lol. I'm a complete Newbie.

Windiv, 'Tablet' - the generic term is used differently for each context. iPad is a generic tablet. While for Photoshop editing, you need a tablet such as Wacom Intuos - they're 'design tablets' in specific. They have 'full-blown' capabilities with Photoshop and majority of other Professional Graphic softwares.
Visit this link for more information: http://www.wacom.com/en/products

How to install and use a client certificate for use with https sites on Android?

I need to be able to install a .p12 client side certificate to be sent to the admin section of my company's site to authenticate me as an employee. In FireFox for PC there is the ability to install this client certificate. In the mobile I cannot figure out how to get this to work.
I just bought an Asus Transformer Android Tablet running Honeycomb. I have tried the following method below:
http://support.mozilla.com/en-US/questions/786035
I get to the screen where I am able to present and choose a certificate but I still get the (Error code: ssl_error_handshake_failure_alert).
Now that Android is really picking up steam, there needs to be a way to install client side certificates to present to sites requesting them.
Is there another way to hack the system to allow or install a client side certificate in .p12 format?

Sorry, there's not a good way to install client certificates in Firefox 4 for Android. A bug has been filed, and any work that we do on adding this feature will be tracked here:
https://bugzilla.mozilla.org/show_bug.cgi?id=478938

I need to download firefox free and take it to home and download it in my laptop for using it web site developing

I tried to download FirFox free from public internet cafe and to take it to home to download it in my laptop for the use of developing htm and css codes. But unfortunatley I failed to download it. I got the answer from the "run" "this doc is corupted." So I need a help what I have to do to download it correctley?

If you are having problems downloading it from http://www.mozilla.com try downloading it from http://releases.mozilla.org/pub/mozilla.org/firefox/releases/3.6.8/win32/en-US/
You just need to download the setup file from that page - '''Firefox Setup 3.6.8.exe'''
If you are using Internet Explorer to download the file, you can right-click on the '''Firefox Setup 3.6.8.exe''' link and choose "Save Target As"
That link is for the English-US version of Firefox 3.6.8, if you need another language, select the Parent Directory link and then choose the folder for your language.
You should also check that the internet cafe allows downloading of executable files. It is also possible that the internet cafe has security software that is corrupting the download.

Best settings for using PE7 for a Kickstarter video?

I'm working on a video for a kickstarter campaign using PE7, with video from my Flip Mino HD. My basic question is what set-up and output settings produce the best quality video for online? Here's what a Kickstarter video should look like.
The video from the Flip is HD, MPEG-4, widescreen. It shows up on PE7 with NO red lines and plays fine there.
The Kickstarter frame appears to be 560px x 420px. They accept MOV, MPEG, AVI, MP4, 3GP, WMV, FLV, with the max. size of 200MB. They also suggest bitrates of around 1500.
I assume I should use the EXPORT function for more choices, rather than the SHARE one? What setting do you suggest?
When I've exported in MOV, MP4, AVI or WMV, I get data on top of the video. Never had this problem before. How do I get rid of it?
Thanks for the help.

If you're editing video from a Flip camcorder, you'll need to upgrade to version 9, the first version of Premeire Elements to support this type of video. No previous version is going to work well with it.
As for output, I'd recommend you use thse output settings. Most likely Kickstarter will accept this video and then automatically convert it to the format necessary for the site.
From the Share tab, choose Computer and then QuickTime/MOV. Choose the DV preset and then click the Advanced button.
From the settings window, do the following:
Video Tab
*Video Codec: H.264
*Quality: 100
*Frame Wdith: 855
*Frame Height: 480
*Frame Rate: 29.97
*Field Type: Progressive
*Pixel Aspect Ratio: square
*Set Bitrate: checked
*Bitrate: 8000 kbps
Audio Tab
*Audio Code: AAC
*Output Channels: Stereo
*Frequency: 44kHz

Possible for using profiler for creating workload for Database Engine Tuning Advisor in case of SSRS reports

I have SSRS reports with each 5 parameters. Parameter datasets includes statements like WHERE @CategoryKey
I have 20 tables in SQL Server. We don't have OLAP cube.
I have created SQL Server Profiler trace. I have clicked all reports during process.
I have opened Database Engine Tuning Advisor.
I have selected all tables to Tune.
Tuning options are Indexes/No Partitioning/Keep all existing PDS
Result is following:
14% improvement
10 recommendations (8 statistic for Calender table and 2 index for Calender)
Tuning logs:
S008 exec sp_executesql N' LongSQLStatment including IN (@CategoryKey) Event does not reference any tables
S007 Replaced event exec sp_executesql
My question is that why I did not get any recommendations for other tables that Calender?
Could it be because of SSRS parameters like @CategoryKey?
Is it possible at all to use SQL Server profile for creating workload in case of SSRS reports with parameters?
I have tables and reports like ProductSales, which I suppose should be get indexedbecause of WHERE statements.
I have where statement like Month and Category and Color.

Yes it is possible to capture a trace using profiler, but please provide the t-sql behind your dataset before I can answer your question about the DTA recommandations.
Regards
Rasmus Glibstrup
http://blog.sqlguy.dk

Any samples for using JMX for displaying cluster statistics 3.6 ?

Hi,
Our Coherence 3.6 cluster is configured in the WLS domain and controlled using WLS node manager. This is all working well. We have created a WLS console extension to show the actual live cluster topology (rather than the configured topology) so we can ensure all the domains are configured correctly and there are no nodes in the cluster that there should not be (we have many domains/environments).
I can show basic cluster statistics and show the members etc using the CacheFactory. But for each cluster member I would like to show if it is storage enabled and free memory and other statistics. I was expecting to get that from the Member or Cluster objects returned from the CacheFactory methods but it seems not. It seems that JMX is the way to go. Does anyone have any sample JMX code they might share that would connect to the cluster and retrieve stats and info that is not available from the CacheFactory api ?.
TIA
Martin

Hi Revanth,
The issue seems to be with the JMX URL value defined in the 'server URL' property.
Apparently I ran into the same issue as I was unable to access the Admin Server URL from the SMA.
Changing the Host and Port value properly resolved the issue for me.
Regards,
Anandraj

Proxy.pac file not working for using proxy for selected websites

After changing my ISP, i cant connect to Bluenest.org directly but with proxy. I can also connect by setting manual proxy server for all websites. But I dont want to do that as there is a bit security problem. I just wrote Proxy.pac files to use proxy sever for that particular website & put its location on Automatic Proxy Configuration. But its not working. I va tried with two types of .pac files. Given the code of the files below.....
First one..........
<pre><nowiki>
function FindProxyForURL(url, host)
if (shExpMatch(url, "http://bluenest.org") || localHostOrDomainIs(host, "http://www.bluenest.org"))
return "PROXY 204.45.138.4:80";
else
return "DIRECT";
</nowiki></pre>
Second one......
<pre><nowiki>function FindProxyForURL(url, host)
if(!isResolvable(host))
return "DIRECT";
return "PROXY 204.45.138.4:80";
}</nowiki></pre>
but none of them working. Please help.
Can you please tell which proxy server is fastest & safest.
Thanx in advance

I submitted a bug report to Apple. The problem is present since 10.9.2, now with 10.10 and iOS. I hope they will take this problem seriously.

Making JButton name a varible for use in for loops

Ok I've got some 98 buttons which are laid out in a grid, and a for loop would work to make thing easier when it came time to make adjustments or changes. Therefore, I would only have to make changes once instead of editing some 196 lines (Making the button, then adding for each button) Both the button names are incremental and their lables
Here is what I got:
// for loops to do the increase of Char Letter and Int Number
String buttonName = "rowButton" + Letter + "" + Number;
JButton buttonName = new JButton( Letter + " " + Number);
// closing of for loop
What do I need to do to make a string value to be the new button's name?

String buttonName = "rowButton" + Letter + "" + Number;
JButton buttonName = new JButton( Letter + " " + Number);
What language allows this? There has to be some language that allows >this, otherwise why do so many people think you can do it in java. Uhmm, actually it works fine in Java. One method to convert an integer to a string is to do:
int i = 10;
String new_string = "" +i;
//new_string == "10"

Any example for using LDAP for WLS7.0

Is there any example I can follow to setup a LDAP as the default security realm
for wls7.0 ?

Hello Friend,
The detailed instructions for setting up an external LDAP
provider for WLS 7.0 can be found at the following link.
http://e-docs.bea.com/wls/docs70/secmanage/realm.html#1172008
I hope that helps.
Regards,
Tom Hegadorn
Developer Relations Engineer
BEA Support
"Friend" <[email protected]> wrote:
>
Is there any example I can follow to setup a LDAP as the default security
realm
for wls7.0 ?

Single SSL Web Listener for hosting multiple web sites

Hi All,
We are currently hosting multiple websites with Single HTTP Web Listener .. As of now it's everything is working fine..
Now we have planned to have SSL for the hosted sites
Each hosting site will have different SSL Certificates and i am little confused to use Single SSL Web Listener to host multiple web Sites...
Can any one guide me to use Singel SSL Listener for using all hosted sites..
We are having TMG on DMZ Network on Single Nic..
KJSUBBU

Hi,
it is no problem to host multiple SSL websites with only one IP address / certificate on the TMG Server. Only the authentication options for the published websites must be unique, because you cannot use multiple authentication options in one Listener
TMG Server uses HTTPS to HTTPS bridging, so you can use Host header and more to distinguish between the different internal websites:
http://technet.microsoft.com/en-us/library/cc995178.aspx
Regarding the SSL certificate on the internal webservers. TMG must trust the issuing certificate authority which issued certificates for these websites and the name you used to connect from the TMG Server to the internal webserver must part of the CN (Common
Name) or SAN (Subject Alternate Name) on the certificates of the webservers
regards Marc Grote aka Jens Baier - www.it-training-grote.de - www.forefront-tmg.de - www.galileocomputing.de/3276?GPP=MarcGrote

How to unset the 'use itunes for internet music playback' option

In Advanced Preferences, I mistakenly clicked the SET button for "Use itunes for internet music playback". Since then, I have closed and opened itunes, so it appears the preference has been saved (the field is no longer highlighted)
I cannot find any way to unset this option. I want to unset this option. Could someone please tell me how?

I don't think that deleting the plist file will help.
Clicking that button sets the handler for a bunch of file types. You can't just unset it, you need to set the handler to something other than iTunes. Normally audio and video are handled by the Quicktime Plugin. You can restore that behavior in System Preferences:
System Preferences -> QuickTime (in the Internet and Network set) -> Advanced -> Mime Settings...
You may have other plugins or programs you want to use for some formats (like .wmv or .avi). Those programs should be able to reclaim the file and MIME types from their preferences.

Using Garageband for live performances

I would love to hear from anyone who uses GB for live performances. I'm especially interested in how you store and play your music; ie direct from your computer drive, on flash card or thumb drive etc. I'm a one man show with guitar, flute, and keyboard. I'm really new at this and any info would be greatly appreciated. Thanks

Hey Gillermo... I might have to eat my words. I had a good think about this last night and I have come up with a plan. Just shooting from the hip and so might need some refinement, but here goes...
The problem as I saw it with Garageband was two fold...
1. how to lay out several songs or groups of pre recorded tracks and tracks with effects on them for my vocal and guitar and
2. lack of an easy to use controller of some sort that worked with GB to minimize mouse use, speed up transfer/choosing between songs and organize my set layout with a structure of some sort.
As a result of mucking around with my Korg NanoKontrol and using the plugin for GarageBand, I can now envision a logical system for using GB for Live performance as a one person show.
The NanoK has the ability to control 8 tracks at a time. You have use of Volume, Pan, Mute, Solo as well as the transport buttons when using scene number 1 on the NK. It has the ability to scroll through groups of 8 tracks at a time with dedicated buttons on fader bank 9.
As a simple example, lets take 4 tracks 1. a track dedicated to vocal with some effects on it to taste 2. a track dedicated to guitar with some effects to taste 3. prerecorded bass track (file bounced down to mp3 or similar) and 4. a drum/percussion track set up like track 3.
Now what you have is the use of 4 tracks for your performance ( there are a few other options though). Now if you load tracks 5-6 with the bass and drums of another song and 7-8 with the tracks of yet another song you now have 3 songs you can play/sing from the first fader bank set. These are all visible on the laptop screen.
Now thinking in groups of 8 tracks, the 2nd set of 8 tracks (tracks 9-16) is set up in a similar way with tracks 9-10 duplicates of 1-2 (vox & guitar) and 3 sets of bass and drums (or what ever). You would name each set of bass and drum tracks with the name of the song so you could always find out where you are. You could also apply instrument icons for easier identification.
So starting with fader bank 1 and tracks 1-4 un muted, you would have muted all the other tracks in the entire set ( before you started your show obviously). Hit play, sing your song... hit stop. Hit rewind, mute tracks 3-4, un mute tracks 5-6, hit play when ready and away you go with song No.2. Repeat for song 3. Once you have completed these 3 songs and made sure all of the tracks are muted via the Nano, press the button that moves the controls to the next set of 8 tracks or 3 songs.
Now in terms of performance there would be some trial and error needed to find out how big the project file could be before there were computer performance issues. I read somewhere there was an upper limit of approx 240 tracks in GB. In reality you would be thinking in terms of how many songs there are in your sets. So in this scenario if you had 15 songs in each set you would only need 40 tracks or 5 sets of 8 fader banks.
To minimize performance issues with projects getting on the large side, in between your sets you could close the project with set one in it and open the project file with set 2 in it.
A couple of other layout options would be to use an entire bank of faders for each song. You could have between 5-8 tracks usable per song. You could have a combination of audio, .wav/mp3, electric guitar and software instrument tracks. Simply go through the mute/unmute process as you scroll through your songs.
You could also lock/unlock the odd track for another level of performance optimization, but you would have to use the mouse pad for this as it can't be done via the NK.
The pro's for this type of system are
1. Complete control of mixing vol & pan for the venue you are in
2. Very simple control at your finger tips, 2 or more faders at a time, limited mouse use
3. A logical frame work to create your sets.
4. You can stay in GarageBand, no need for another software program.
5. Very cheap investment.
The Con's would all revolve around your computer spec's.
1. Max out your RAM.
2. Be selective with effects
3. System HD speed.
Note, I am assuming my vox and guitar are going through and audio interface with outs to an amp or PA of some sort.
I am going to have to try this out. I really DO NOT LIKE Ableton Live. It is heavy on CPU and gets really deep very quickly. If this works then I will have an Live Serial# for sale.

Config for using 1242 for site survey

Similar Messages

Maybe you are looking for