Configuration AC1750 and WRT120N(extension access point)

I have 2 routers:
- 1 AC1750
- 1 WRT120N
The first one is the main and I want to extend my wifi zone with the second one.
I am not an expert so can somebody help me to configure the WRT120N step by step.
Thanks for your great help

I have done this with my WRT120N and it works
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=3733

Similar Messages

AAA configuration and Linksys Wireless Access Point

Hi,
Can we authenticate Linksys Wireless Access Point thru ACS TACACS+ or RADIUS ? If yes , please tell me the config steps.
Thnaks .
Anil K.

Hi,
Can we authenticate Linksys Wireless Access Point thru ACS TACACS+ or RADIUS ? If yes , please tell me the config steps.
Thnaks .
Anil K.
Check out the below link for Linksys with Radius server authentication:-
http://forevergeeks.com/setup-linksys-router-with-radius-server-authentication-2
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

How do I configure WRT54G as a wireless access point?

Ater a whole series of problems related to Vista, a WAP54G, Airport xpress, wireless printers, etc. plus at least three hours on the phone with Linksys tech support acessing my computer remotely and still not fixing the problems, I dumped my WRT54GC for a Belkin-N router. I set it up over the weekend and slowly regained internet access, then the pinter, then the Airports.
I still would like to have an access point because my signal strength even with the new N router is too weak downstairs to allow my PS3 to connect to it. I cannot figure out how to configure the WAP54G to make it work. I want to take a shot with the WRT54GC. From what I've read, I should be able to do it.
I can get into the router (referring to the Linksys) no problem. I can reconfigure it to an extent, changing the IP address to the recommended 192.168.1.2. I do this by running an ethernet cable from my PC to the router. Howver, after changing the IP address in the router I can't get into it any more using the new IP address. When I attach teh Linksys router to the Belkin I can't get in either.
Both the Linksys and the Belkin use 192.168.1.1 as the default IP address for each device.
I would like to know what settings I need to change i nteh WRT54G to turn it ino an access point -- an extenson of my existing network with teh Belkin router attached to the Comcast modem. I have looked at various how-to's and they all seem to assume I am connecting the two routers with an ethernet cable. If it's not clear at this point, I'd like to connect them wirelessly.
Thanks.

Thanks so much for the reply.
I was working with it all last night and somethign strange happened. After reading some other info on the internets, I changed the IP address on the WRT to 192.168.2.1. It updated, I then ran the wire from the Belkin to the WRT, I typed in 192.168.2.1, it took me to the Linksys setup page, but when I clicked "wireless" in the WRT setup, it took me to the Belkin setup page. How in the world did that happen?
Armed with tis new info, I did a hard reset on the WRT -- assuming it would change the WRT back to 192.168.1.1 -- got into the setup, turned off DHCP, left the IP as .1.1, and then wired it again into the Belkin. I can now get into the setup of either one.
Here's the thing: I don't want the two routers wired together. I want to move the WRT downstairs so a PS3 can pick up the signal. I want the WRT to wirelessly relay that signal to the Belkin to get the PS3 onto the net. I can't run a wire from the Belkin to the WRT.
I've read conflicting reports about whether the WRT can do this. Other sites suggest adding 3rd party firmware to add that functionality but that will definitely push the bounds of my abilities and likely exceed them. So, can the WRT even function in this way?
Inre the WAP, I don' know why but my ability to access the setup menu via 192.168.1.245 is very hit or miss -- much miss than hit. It makes no sense unless there is a bad connection somewhere because I hard reset, wire it to my laptop, put in the IP, and time out 19 times out of 20. I've got the MAC address for the router, and I think I know I want it to function as a repeater, but I've not been able to get that working right eihter.
Thanks for any further reply.

Wireless bridging is not working in 1552 outdoor access point and 2602e indoor access point.

Hi,
I am have been tested wireless bridging with 2 indoor Cisco 2602 access point by following the attached document and its working fine without any issue.
After then I made one Cisco 1552 EU-M-K9 outdoor access point as RAP, then connect to this RAP with one 2602 mesh access point. But its not working, mesh access point is just start scan the signal to get associate with RAP, but not getting established. Is there any specific configuration required to connect between outdoor and indoor access point. Kindly find the attachment and advise.
regards,
Jubair.S

Hi Team,
Any suggestion??
Regards,
Jubair.S

How to configure MSI RG54SE II as Access Point ?

I have an msi router:
Firmware Version:
3.5.2 Build 070402 Rel.60023n
Hardware Version:
RG54SE II v1 081520C2
And i want it to configure it as an access point to a wireless network/ or another access point . Can you help me on how i do this ?
Regards,
Daniel

Hi. I Had a similar problem and found a solution. If you have another device as your primary router then:
1. connect ethernet cable from LAN port of your primary router to LAN port (NOT WAN!) of your RG54SE (I will just call it MSI).
2. go to web interface of MSI
3. if MSI has ip address in wan connection then release it. (Network->WAN) (I set my wan connection type to dynamic ip because there is no option to disable it)
4. in Network->LAN set ip address different from primary router (but in the same subnet) and out of DHCP pool
i.e. if your primary router has ip address 192.168.1.1 and its dhcp pool is 192.168.1.100-199 then you can set local ip address of MSI to 192.168.1.2
5. Disable DHCP on MSI router.
6. If your primary router also has active wi-fi then you must switch MSI wi-fi to another channel, so they do not interfere with each other.
that's it! It's simple and it works!

Bridge to bridge and bridge to access-point via wireless is it possible.

here;s my topology i am trying to configure. i have a router whose ethernet is connected to a bridge.this bridge 1 is connected to a bridge 2 via wireless. now i am trying to connect a access-point via wireless to this bridge2. is it possible for bridge 2 to support connectivity to the bridge1 and the access-point both of them via wireless.
can someone pls help me on this.
waiting for someone to reply.
regards
sebastan

You can set up each radio in the access point for different functionality. Considering the scenario, this can be done by setting up the SSID for the G radio and another SSID for the A radio. Then, set the role in the radio network parameter for the G radio to access point and for the A radio to the root bridge role.
ou can prevent unauthorized users from reconfiguring your access point/bridge and viewing configuration information. Typically, you want network administrators to have access to the access point/bridge while you restrict access to users who connect through a terminal or workstation from within the local network.
To prevent unauthorized access to your access point/bridge, you should configure one of these security features:
Username and password pairs, which are locally stored on the access point/bridge. These pairs authenticate each user before that user can access the access point/bridge. You can also assign a specific privilege level (read only or read/write) to each username and password pair.
http://www.cisco.com/en/US/products/ps5861/products_configuration_guide_chapter09186a00804ed6d4.html

Bridge to bridge and bridge to access-point is it possible

here;s my topology i am trying to configure. i have a router whose ethernet is connected to a bridge.this bridge 1 is connected to a bridge 2 via wireless. now i am trying to connect a access-point via wireless to this bridge2. is it possible for bridge 2 to support connectivity to the bridge1 and the access-point both of them via wireless.
can someone pls help me on this.
waiting for someone to reply.
regards

Take a look at my suggested config below. The first accesspoint will broadcast a SSID for clients and use a different SSID for the bridge. This setup has no 802.1x mechanism yet, but you can add that later. For the topology see PtoPLinkExample.gif posted earlier.
----- Accesspoint 1 --------------
dot11 ssid bridge
authentication open
dot11 ssid WiFiNet
authentication open
guest-mode
interface Dot11Radio0
ssid bridge
ssid WiFiNet
----- Accesspoint 2 --------------
dot11 ssid bridge
authentication open
interface Dot11Radio0
parent 1
ssid bridge
station-role workgroup-bridge
----- Accesspoint 3 --------------
dot11 ssid WiFiNet
authentication open
guest-mode
interface Dot11Radio0
ssid WiFiNet

WRT54Gv7 and 2 Netgear Access Points WG602

Hi,
is it possible with a WLAN Broadband Router Linksys WRT54Gv7 and with 2 Netgear Access Points WG602 configure a Multi Point Bridging?
is it right that the WRT54G version 7 can not be upgraded to a own Firmware?
does the WRT54G version 7 supporting WDS?
thank you very much.

the router can only be configured as an access point..it cannot be configured in repeater or bridge mode...
also , i don't think that it can be upgraded to a third party firmware ..

SSIDs and VLAN on access points

The commands to map an SSID to a VLAN on an IOS access point are basically like this:
[snip]
dot11 ssid MYSSID
vlan 5
interface Dot11Radio0
ssid MYSSID
interface Dot11Radio0.5
encapsulation dot1q 5
bridge-group 5
interface FastEthernet0
interface FastEthernet0.5
encapsulation dot1q 5
bridge-group 5
[snip]
My question is this: what does the command "vlan 5" actually do? Does it map MYSSID to bridge-group 5, which is then mapped to 802.1q tag 5 by the subinterface configurations (so that the tag number is arbitrary), or does it map MYSSID to 802.1q tag 5 on the radio interface, which is then bridged to the appropriate dot1q subinterface on the wired side by the bridge group (so that the bridge group number is arbitrary)?

Vlan tag is tied to SSID and Bridge group is also tagged to appropriate vlan mentioned as bridge group number

Placement and Location of Access Points

We are just starting a new build on our school, included on this is the installation of wireless over the top of our existing network.
I have read that cisco and other vendors supply free software to automate the placements of wireless access points, but I can't find it anywhere?
Any ideas or advice?
Thanks
Steve Audus
Chaucer School
Sheffield UK

WLSE can help you to adjust the radio coverage. However, WLSE is not free.
We usually recommend you to hire a third party vendor to do a site survey. The vendor will take various antennas with them. They put different antennas in different positions; so that it gives you the best coverage. Finally, the vendor will give you a blue print and tell you the placement of APs/antennas.

Configuring Discussion and Announcement Connections to point to cluster

Hello,
I'm wondering how I'm supposed to configure my connection to the Discussion server for my Portal sites.
I don't know if I'm suppose to point to the first node of the discussion server on the portal server 1 and to the second node of the discussion server on the portal server 2 ?
Or should I configure my discussions server URL to point to the OHS that will then map to the correct server ? (I don't like this because it means going from lan to dmz to lan again ...)
How do you configure it?
Thanks !
Emilien

Emilien,
When you configure your environment for high availability, you will often also add a load balancer in front of the Oracle HTTP Server (OHS)
You should point to that load balancer, which in turn points to one or more OHS's, which in turn point to one or more managed servers, running your discussion app.
If you do not use a load balancer, and have only one OHS in front of multiple managed servers, point to the one OHS.
Kind regards,
Rob

E90 / E51 (and other?) --Access point groups-- ar...

Hi All
I‘ve seen that in the new E51 the Access point groups are gone.
In my (older) E70 the Access point groups are installed and they are GREAT.
It’s a pity, that they are gone, because you waste much money to your provider, and you lose connection-performance.
Now in the E90 and E51 (AND PERHAPS IN THE UPCOMING PHONES) the possibility of building groups is not available.
It’s a shame for a business Phone.
You don’t know, what “Access point groups” are?
Here the explanation of the E70’s manual:
Email data roaming
Access point groups.
Your device allows roaming between wireless access technologies, such as WLAN and GPRS, for e-mail. For example, you can
start an e-mail session at home and continue the session on your way to work. While your session continues uninterrupted,
your handheld device switches from WLAN to GPRS and back to WLAN when you arrive at your workplace.
In result: You have a quick and free connection at home (Wifi), you go outside, the phone switches automatically to e.g GPRS, you come in the office, the phone switches automatically to your company’s WIFI.. etc.
You pay only the short time outside, and you don’t have to worry about changing connections.
Let us motivate NOKIA to reintegrate this feature, so they become more professional and businesslike
Thanks mayba

Bring IT back !!!

Regarding cisco 1400 and 1500 outdoor access point doubt

Hi,
I have a requirement of installing 1400 outdoor access point in bridge mode .
client has got three remote offices which will be connected through 1400 outdoor access point.
but i came across about lightweight and autonomous version where i am quite confused.
which version is available in market especially for 1400
If i could get information about 1500 also , it would be great help .
If i want to connect all the remote offices in brigde mode . which will be convinient for me ?
If I could get any link with datasheet for both the access point seperately, it would be great.

Hi,
1500 is for MESH network.. 1400 is for bridging in autonomous mode.. most of the time we use 1400 for bridging between two diffrent sites..
1400 bridges do not work in LWAPP mode.. its always Autonomous.. where in the 1500 canot work in autonomous as well and needs a WLC..
here is the datasheets for 1400 and 1500..
http://www.cisco.com/en/US/partner/prod/collateral/wireless/ps5679/ps5279/ps5285/product_data_sheet09186a008018495c.html
http://www.cisco.com/en/US/docs/solutions/Enterprise/Mobility/emob41dg/ch8_MESH.html
lemme know if this answered ur question!!
Regards
Surendra

Linksys router ezxs55w and wireless g access point

My laptop has suddenly stopped seeing my wireless connection. I can see the ones that belong to the neighbors, but not mine. Have rebooted computers, reset access point (even bought a new one but nothing changed) unplugged, etc to no avail. HELP! Do I need a new router? The led lights are green for link/act and 100, orange for full/col. The connection has worked with no problems for close to a year. Thank You

Whats the Model number of the Access Point? When you search for the Wireless Networks on your computers are you able to locate (linksys) under the wireless networks?
EZXS55W is a Swtich. So you have connected the Access point to the Switch? and where the switch is connected, is it connected to the Router or to the Modem? Who is your ISP.

How to configure wrt54g router as an access point when connected to a 3Com switch

I'm trying to use my linksys router as an access point to keep from having to make more network drops. I can't figure out which IP address/gateway to use on my router to get it to communicate with my switch. The 3Com switch address is 10.1.10.250, gateway is 10.1.10.1, netmask is 255,255,255,0.The linksys router has been reset to defaults.
I know that it can be done but I'm having the hardest time making it work.

For the DD-WRT firmware, you can try this link .
For the price of your Acess Point you can try this link .

Configuration AC1750 and WRT120N(extension access point)

Similar Messages

Maybe you are looking for