Consumer producer - Acquisiton image but only producer loop run

Dear all
I try acquire and save image from Basler camera L301kc and NI PCe 1427 framegrabber. I create a producer/ consumer loop because the save take more time that the acquisition and if I do both in the same loop I lose frames. But I have problem: only producer loop run.
I have read all the threads but I didn't manage to solve my problem.
I have attached a VI code of how I was trying to do it. I am using LabView 2011.
Please any comments or help is deeply appreciated.
Thank in advance
XuanThuy
Solved!
Go to Solution.
Attachments:
Acquisition Image for Sample 03.vi ‏75 KB

Dear Kira T,
The producer and consumer loop has run but the Image Out in consumer loop is empty. Bruce attention to the error wire from the consumer loop wired to the destroy queue vi. But I don't find error.
I have attached a new VI code.
Can you help me ?
Thanks and regards
XuanThuy
Attachments:
Acquisition Image for Sample 03.vi ‏71 KB
Linescan camera setup Sub VI.vi ‏26 KB

Similar Messages

  • Since the last update I have been unable to print from Firefox. No problem printing from Safari or any other program. I've seen a few responses to this problem but only to people running Windows. I'm on a Mac running v. 10.5.8

    Since the last update I have been unable to print from Firefox. No problem printing from Safari or any other program. I've seen a few responses to this problem but only to people running Windows. I'm on a Mac running v. 10.5.8.

    Also when I click on the link in my email to activate my account (in the hopes that a solve will be emailed to me) I get this message -
    "Something is wrong
    We could not activate your account. Please make sure that you have clicked the correct link in your email or typed in the correct address."
    Same message if I cut and paste the link.

  • .pdf prints very small - full image, but only quarter page

    i have adobe reader 10.1.1 for mac.  when I print, the full image prints, but is shrunk to the top left quadrant of the paper.  I have tried to change page scaling settings.  i have also changed advanced setting 'print as image', but none of this seems to work.  i've spent endless hours on this and am hoping someone can offer a suggestion.  this happens regardless of the original application (.xls, .doc, .ppt).

    Here's your answer
    http://forums.adobe.com/message/3810431#3810431

  • As an asset management tool it should manage all images but only adjust raw

    Is Aperture an image management tool, raw converter/workflow tool, or both?
    Let it be both! Restrict what is is ALLOWED to ADJUST, but manage it all.
    When I do a shoot, I start out with 300-1000 RAW images.
    By the time I am finished with the client I will have narrowed the pile of image assets down to 20% of the original RAW files, JPGs of all of those, AND 10% of the selected originals will also end up as layered PSD/TIFF files. But when I go back in and want to open a PSD file then why not allow just that Then save it back as the same or a version..
    OR when I tell it to open a PSD file in CS2 it will as "make a version(full or flat), or edit original?" and of course a "don't ask me again for this format" check box!
    So why not leave the layered PSD/TIFF files alone and NOT allow them to be adjusted, only managed?
    Think about it, IF I want to adjust my multilayered PSD file I will most definitely only trust that to CS2 where I retain full creative control over the layers, and I can output a version if I want!
    IF I am crazy enough to feel the need to use the shallow tools of Aperture to tweak the brightness/level/curves/saturation/WB/etc/etc of a flattened COPY of my layered PSD file then I will make a copy and drag it into Aperture. By shallow I mean that CS2 and layers has much more control than the single layer tools of Aperture.
    As an option leave it open as a configuration choice in the prefs... "Adjustable image formats: RAW, JPG" and even on a per image basis, right-click--> image status-->Adjustable or Unadjustable.
    Yes, I sent this idea off to Apple!

    Moki,
    Right there with you. Here's my rough scenario:
    1. I shoot 500 RAWs.
    2. Cull down to 100 keepers.
    3. Client culls down to their 50 selects.
    4. Anywhere from 25-50 become layered PSD files, depending on the presentation the client wants (sizes, packages, borders, special effects, etc.).
    5. In addition to those 25, there may be *completely new* composites (PSD's) created from combinations of the 25 -- this isn't a version of one of the original masters -- it is a *completely new* image that Aperture needs to manage in the project (so import of PSD without flattening and/or allowing Photoshop to Save-As into the Aperture library is a must).
    I'd even add to your request about allowing adjustments. It would be totally cool if the adjustment tools were context-sensitive, enabled when working with an image (like RAW or JPG) where Aperture can adjust, and disabled when working with an image (like layered PSD or TIFF) that it won't adjust.
    Anyway, I have complete confidence that eventually, the RAW conversion will be fixed, so even though that's an immediate glaring issue, it doesn't seem to me to be the long-term workflow killer. Being able to traverse this editing stage of the workflow with Photoshop is crucial. Without this, its basically
    a complete project export after the initial organization stage, and the rest of the workflow is either managed entirely in another tool, or a complete pain to bring back into Aperture for output, which leaves files strewn everywhere for backup and archiving.
    Brad

  • 15MB raw image but only 256x192 size available

    I downloaded raw images to aperture 2 before I added raw patch for Canon G10. After downloading RAW patch I can't view these images larger than 256x192 thumbnail size, but file size appears to be 15 MB. Can this be corrected?

    Thanks, unfortunately it is not possible to do this since I've already formatted the card. I'm afraid I was hasty more than once during this process (new camera and software update). The only thing that gives me hope for a solution is that the file size indicates that the files are there, and when I use the loupe it only magnifies a small portion of the thumbnail as if it is seeing the image at full size.

  • [Solved] ping requires root privilages but only if OS run from RAM

    I have an odd situation where I can use ping as a regular user from openbox's autostart if I run the OS from storage disks but not if I load the OS into RAM. It only works for a regular user with the OS loaded to RAM when I set the sticky bit.
    Can this be a timing problem with systemd not activating a required service in time?
    Last edited by KairiTech (2014-08-26 21:16:45)

    Yep! That's it exactly. I create a root file system archive to speed the loading into RAM. See the exact code below:
    sudo tar -vzcf /rootfs.tar.gz / --exclude={/rootfs.tar.gz,/boot/*,/var/cache/pacman/pkg/*,/dev/*,/proc/*,/sys/*,/tmp/*,/run/*,/mnt/*,/media/*,/lost+found}
    Adding the --xattrs option to tar solved it.
    Last edited by KairiTech (2014-08-26 21:17:46)

  • 4 accounts but only 2 can run safari

    OK - I'm a newbie to Macs but here is my situation.
    There are 4 accounts on my computer.
    Mine and my husbands and run and use safari just fine.
    both of my daughers, who are managed accounts, can not run safari.
    They get the "Safari cannot open webpage." error
    This is really weird because just 2 days ago they were using it just fine. As a matter of fact, they have been using safari since we got the computer a year ago.
    What's the deal! I cannot figure it out.
    I've shutdown, restarted, and a whole bunch of other stuff!
    HELP please!

    Hello,
    "I've shutdown, restarted, and a whole bunch of other stuff!" Can you define... whole bunch of stuff? If you haven't repaired disk permissions..
    Launch Disk Utility. (Applications/Utilities) Select MacintoshHD in the panel on the left, select FirstAid, then click: Repair Disk Permissions. Quit DU when it's finished and reboot.
    Carolyn

  • My macbook pro can see the network, gets full signal, but won't connect.  When I run diagnostics, it automatically connects, but only if I run the diagnostics.  Why won't it connect by itself?

    Macbook Pro won't auto connect to wifi, but when I start diagnostics, then it will connect.  It seems it requires diagnostics in order to get connected to wifi.
    any ideas

    SOLUTION! 
    I've been suffering from this problem for a few months.  I tried everything suggested by everyone, and then, today, I had a mad idea. 
    I used to work in a room in the house that's about 12 metres away from the router. It's on the next storey up and horizontally about 8 metres away.  The problem started when I began to work in the same room as the router. 
    Today I became so frustrated that for some reason I walked into a room about 8 metres away on the same level - Guess what?  I connected with no problem at all. Feeling full of joy I walked back to the room where the router is located - Dropped internet connection within a few minutes!  Walked back to the the room that's 8 metres away and, hey presto! I have a connection. I now realise that the problem was that I moved too close to the router.
    I can think of no logical explanation for my experience, but empirically it seems to work.  Does anyone have the faintest idea of why this should be the case?  In the absence of an answer I think I may have to start believing in fairies at the bottom of the garden - I'm just off to set a meal for them.
    By the way, I don't know if it has any significance, but the router is a BT Infinity router that has replaced the incredibly unreliable Virgin Media cable connection

  • Payroll : Return indirect result from fast formula only in first run

    Hi All,
    I need to return an indirect result/element from a fast formula but only in first run of the element. For example I have an element "XYZ" and want to retun one value to element "ABC" (non-recurring earning element to pay loan amount to employee) if this is the first run of the element "XYZ" in other subsequent run I do not want to return any value.
    I could have other options to deal with the issue but due to sudden change in the requirement I am left with this option only. Is there and seeded validation/flag or database item i can use to check the first run of element.
    Thanks,
    Avinash

    Create a Balance that is fed by the Indirect Element. In the Fast Formua,check for the <Balance>ASGPTD. IF the Balance value is not Zero, then do not trigger the Indirect element (Better way to do is calculate the Loan to be paid and subtract the Balance_ASG_PTD from the calculated amount. IF the net value is not zero, then trigger the indirect element. This will ensure that the Loan element will be triggered only once). When you referred, First Run...if it is not first run per period but the first run of the element per employee, then use _ITD Balance.                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                   

  • I have 3 consecutive movie clips that I am trying to drop into the drop zone but it only recognizes the first one and only produces the firts one in a DVD. How can I drop all three  movie clips into one drop zone

    On IDVD, I have 3 consecutive movie clips that I am trying to drop into the drop zone to create a DVD but it only recognizes the first one I dropped and only produced the first one in a DVD. How can I drop all three  movie clips into one drop zone.

    I have had some luck doing the following: Export each clip from imovie as a quicktime clip. Open iDVD and create a new project. Import a few stills into iDVD and then click on the button that gets created to get into the screen where the individual slides appear. Drag each quicktime into that screen and arrange in the order you want. You can then delete the stills. The button that appeared when you dropped in the stills will launch a complete show.

  • Video playback on external monitor only producing still frame

    I am trying to use a HD TV as a playback device as managed to get it to work, however it has now stopped working and only produces a still frame. When I hit play it will play fine in the timeline but display only a still frame on the second monitor. I have made sure that the settings under video playback are set to full screen and that mirroring is turned off.
    Even when I play back on Main the image on the main monitor only displays a still frame until the second monitor is unplugged.
    Am I missing something?

    How is the TV connected?
    If via firewire and an analog/DV converter, are you feeding the HDTV something other than a DV signal? If so, it won't work.
    x

  • Xperia Z2 with Google Camera Photosphere only produces Crap Pics Help or suggestions needed.

    Hi,
    I have the same problems with my Sony Xperia Z2
    I hope somebody has found a solution for this.
    I really like the phone and it would be a pity to have to sell it again because i use Photosphere a lot.
    Actually, I was completely satisfied with the Experia Z2.
    The camera also superb! Close-Up DSLR quality.
    But the main reason for the purchase was the possibility to use Google Photospere for private and professional use.
    Unfortunately, I have now found that my Xperia Z2 in conjunction with Google photosphere only produces images that are really not worth to be published .Errors and blurry spots and areas in ANY! Image.
    I must say that I already tried all possible settings and resolutions .I have downloaded the latest version of Google camera and on the Z2 runs Android 4.4.4
    I do not mean the normal error or is not appropriate Stiching but quite massive focus error.
    For comparison, I previously had a Note 3 with an 8 MP camera.
    The Note 3 I sold again only because of bad connection quality.
    But the Note 3 has perfect spherical panoramas generated without the error occurring in the Xperia Z2.
    So the app is not the problem.
    My guess is that the Z2 camera focuses just completely wrong when creating some of the images.
    And Google photosphere can of course also generated solely those blurred images with.
    I would not like to have to sell the Z2 again because I completely satisfied bin.Everything else works well with everything outside photosphere.
    If someone has had similar experiences or if someone has a solution for this I would be very grateful.
    I have here some excerpts panorama link so that you can see what I mean.
    This blurring spots and areas are common to all views and in a wide variety of lighting situations and settings.
    https://farm9.staticflickr.com/8604/16041710974_36b8a93de0_k.jpg
    https://farm9.staticflickr.com/8665/16664018385_7ebca55276_o.jpg
    https://farm9.staticflickr.com/8562/16041714734_0230a1288e_k.jpg
    https://farm9.staticflickr.com/8613/16041716784_b954d11ada_h.jpg
    And here to compare a Panorama from my previous Note 3 with exactly the same App (not edited )
    https://www.360cities.net/image/snow-in-hasenheide-29-12-2014-wissmannstrasse
    If i sent the phone to the repair service most likely they'll tell me they are not responsible for any non Sony Apps behaviour.
    But actually no other Z2 user i talked to so far had this problem.
    Greetings from Berlin
    Martin

    But photosphere its available for other Phones, not just Xperias. 
    Here is something you could try 
    repair your phone with PCC and then Do NOT install any app just photosphere and try again.
    PC Companion (PCC)
    Bridge (for Mac)
    Alternatives on How to backup Xperias
    http://talk.sonymobile.com/thread/36355
    "I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

  • Photomerge Panorama produces small image

    I'm trying to use Photomerge Panorama with 3 10MP images. It's a vertical panorama but if I arrange the images manually, Photomerge stitches them nicely.  The result is a high quality HDR panorama - but it's only about 1K pixels wide, and therefore useless.  I don't see any step where I can affect this resizing, which seems to happen on its own, arbitrarily.  Is this a bug? Is there any way to get Photomerge to preserve the resolution of my photos when stitching them?

    This is happening with Elements 8.
    I'm reviving this thread because I'd really like to use this feature - but it's apparently broken, and if Google is telling me the truth, it's never really worked reliably in any previous version of Elements.
    By selecting manual positioning, and flipping between 'perspective' and 'reposition', I can sometimes trick Elements into trying to stitch a full size panorama; I see the images suddenly pop back to full size; but E8 then grinds for a while, then the Photomerge UI closes, and no image is produced.  Nothing.  Or sometimes E8 just locks and has to be killed with Task Manager.
    My source images were TIFF - I tried converting them to JPG - it made no difference.  There's nothing unusual about these images, they're just 10MP photos. I've tried other options in Photomerge Panorama, and the result is always the same.   Apparently it will only produce a panorama at about half the resolution of the original images - basically useless.
    Does anyone use Photomerge Panorama to successfully get a full size image?  Does anyone know if this feature works properly in Elements 9? 

  • In Federated portal's consumer, cannnot see the roles from producer

    We are configuring a Federated Portal.
    On the consumer's UME, we can see the producer in the UME data source
    drop down. However NO roles can be seen under this producer.
    The connection test is successful.
    Can anybody help with this?
    Points guaranteed. Thanks!

    Hmmm. Not sure - are starting on SP13.
    Isn't there a proxy-to-remote migration tool?
    From Release Notes for SP10:
    <b>New Migration Tool for Remote Role Assignment
    In SAP NetWeaver SPS9, the remote role assignment mechanism changed. We described delete-recreate procedure you needed to perform if you wanted to create new remote role assignments with an existing producer or proxy-to-remote role from SAPNetWeaver SPS8 and earlier (see Implementing a Federated Portal Network (Enhanced and Changed)).
    In SAP NetWeaver SPS10, we now offer a migration tool instead of the manual delete-then-recreate procedure. The tool searches for existing producer objects that contain old proxy-to-remote roles assignments (created prior to SAP NW7.0 SPS9), and updates them with the newer remote role assignment capabilities provided by the User Management Engine (UME). Old proxy-to-remote roles are still functional in SAP NW7.0 SPS10 and later. You only need to run the migration tool if you want to make new remote role assignments using older producer objects.
    For instructions on using the tool, see SAP Note 980480.</b>
    Have you done this? Not really sure you do unless you are making new assignments...

  • I am using the Adobe Acrobat Reader on a mac and I followed all the directions to copy an image but when I press paste only half of the image appears or it appears as an empty square. What can I do to fix this?

    I am using the Adobe Acrobat Reader on a mac and I followed all the directions to copy an image but when I press paste only half of the image appears or it appears as an empty square. What can I do to fix this?

    Hello,
    I would like to inform you that not all the browsers and online PDF readers support copying text from a PDF. If you have opened the PDF online, please download PDF file to your computer and then open the file in Adobe Reader.
    Please share a screenshot if the issue still persists.
    Regards,
    Nakul

Maybe you are looking for