Control file not updated till date in RAC two node database

Hi,
Good day.
To my surprise i found that control files, in our database RAC with two nodes, are not updated till date except one from node 1 and another from node 2.
But we got all the controlfile names in the init parameter file, in both the nodes.
Node 1
bash-3.00$ ls -lrt
total 922128
-rw------- 1 oracle dba 157286400 Nov 3 2007 cntrl03.dbf
-rw------- 1 oracle dba 157286400 Nov 3 2007 cntrl02.dbf
-rw------- 1 oracle dba 157286400 Apr 12 17:21 cntrl01.dbf
Node 2
bash-3.00$ ls -lrt
total 922128
-rw------- 1 oracle dba 157286400 Mar 30 09:17 cntrl03.dbf
-rw------- 1 oracle dba 157286400 Mar 30 09:17 cntrl02.dbf
-rw------- 1 oracle dba 157286400 Apr 12 17:20 cntrl01.dbf
As you could see cntrl01.dbf is the only file updated till date in both the nodes. The database is running fine.
what is actually happening?
Any suggestions?
Thanks,
Balu.

As you're using RAC it is very likely that you are using an SPFILE.
Connect as a DBA account (or an account with SELECT ANY DICTIONARY privileges) in both the instances and do "show parameter spfile" and "show parameter control" (or query V$parameter)
It is likely that the spfile is referencing only 1 controlfile.

Similar Messages

Upgradation of Primary (RAC) two node database and single node standby DB

We have our primary setup in Oracle RAC in 10g R2 (10.2.0.1.0) in HP UX 11i 64bit (PA RISC). It is a two node RAC.
And we have a single node standby database (DR).
Both the primary and standby database are existing in 10.2.0.1.0
We need to upgrade the primary and standby database from 10.2.0.1.0 to 10.2.0.4.0
Am planning to go through the DBUA method for upgrading the database.
I like to know is there any special cases for upgrading both the primary and standby database.
since as i mentioned i will upgrade the database through dbua method, and if i upgrade my standby database as same as primary,
will it forcefully open the database, because while we upgrade the database through dbua it will open the database at the end of installation.
Is it possible to upgrade the standby database with DBUA method even when my standby database is in Mount state.
I will be helpfull if anyone has done this earlier, are there any know issues and is there any good document which i can refer.
with regards
A.Aravind

hi,
thanks for your reply, and i was following the document.
I like to know that is it mandatory to create a new Oracle Home for upgrading from 10.2.0.1.0 to 10.2.0.4.0
or i can proceed the installation of software in the same oracle home.
I will list out my action plan, please correct me if am wrong,
In Primary RAC,
a) Shutdown the database
b) Shutdown the asm instance
c) Stop the nodeapps services
d) Stop the cluster ready services.
e) Stop the enterprise manager
f) Stop the isqlplus
In Standby single node database,
1)Cancel the managed Recovery process
2) shutdown the database
3) Shutdown the asm instance.
PATCHING Process
g) Apply the oracle clusterware patch 10.2.0.4.0 in the same old existing ORA_CRS_HOME
h) Apply the oracle database software patch 10.2.0.4.0 in the same old existing ORACLE_HOME
Note: In my case both the ORACLE_HOME and ASM_HOME are in the same location.
i) Execute dbua to update the database in the primary database.
j) Apply the 10.2.0.4.0 patch in standby database ORACLE_HOME where as ORACLE_HOME and ASM_HOME are in the same location
k) Copy the recently generated archive logs from primary to standby manually and apply in standby database.
l) Mount the database in standby
m) Start the Managed recovery process.
with regards
A.Aravind

Control file not created at time of installtion

control file not created at time of installtion of oracle database
now how we can create it
see alert file
Dump file e:\ORacle\admin\new\bdump\newALRT.LOG
Tue Sep 09 10:45:53 2003
ORACLE V8.1.6.0.0 - Production vsnsta=0
vsnsql=e vsnxtr=3
Windows 2000 Version 5.0 , CPU type 586
Starting up ORACLE RDBMS Version: 8.1.6.0.0.
System parameters with non-default values:
processes = 59
shared_pool_size = 52428800
large_pool_size = 614400
java_pool_size = 20971520
control_files = e:\ORacle\oradata\new\control01.ctl, e:\ORacle\oradata\new\control02.ctl, e:\ORacle\oradata\new\control03.ctl
db_block_buffers = 19200
db_block_size = 8192
compatible = 8.1.0
log_buffer = 32768
log_checkpoint_interval = 10000
log_checkpoint_timeout = 1800
db_files = 1024
db_file_multiblock_read_count= 8
max_enabled_roles = 30
remote_login_passwordfile= EXCLUSIVE
global_names = TRUE
distributed_transactions = 500
instance_name = new
service_names = new
mts_dispatchers = (PROTOCOL=TCP)(PRE=oracle.aurora.server.SGiopServer)
open_links = 4
sort_area_size = 65536
sort_area_retained_size = 65536
db_name = new
open_cursors = 100
os_authent_prefix =
job_queue_processes = 0
job_queue_interval = 10
parallel_max_servers = 5
background_dump_dest = e:\ORacle\admin\new\bdump
user_dump_dest = e:\ORacle\admin\new\udump
max_dump_file_size = 10240
oracle_trace_collection_name=
PMON started with pid=2
DBW0 started with pid=3
LGWR started with pid=4
CKPT started with pid=5
SMON started with pid=6
RECO started with pid=7
Tue Sep 09 10:45:55 2003
starting up 1 shared server(s) ...
starting up 1 dispatcher(s) for network address '(ADDRESS=(PARTIAL=YES)(PROTOCOL=TCP))'...
Tue Sep 09 10:45:58 2003
create controlfile reuse set database new
datafile 'e:\ORacle\oradata\new\system01.dbf',
'e:\ORacle\oradata\new\temp01.dbf',
'e:\ORacle\oradata\new\rbs01.dbf',
'e:\ORacle\oradata\new\indx01.dbf',
'e:\ORacle\oradata\new\tools01.dbf',
'e:\ORacle\oradata\new\dr01.dbf',
'e:\ORacle\oradata\new\users01.dbf'
logfile 'e:\ORacle\oradata\new\redo01.log' size 1M,
'e:\ORacle\oradata\new\redo02.log' size 1M,
'e:\ORacle\oradata\new\redo03.log' size 1M resetlogs
Tue Sep 09 10:46:03 2003
ORA-1503 signalled during: create controlfile reuse set database new
datafile...
Tue Sep 09 10:46:03 2003
alter database new open resetlogs
ORA-1507 signalled during: alter database new open resetlogs...
Tue Sep 09 10:46:14 2003
alter database new character set WE8ISO8859P1
Tue Sep 09 10:46:14 2003
ORA-1507 signalled during: alter database new character set WE8ISO8859P1...
Tue Sep 09 10:46:14 2003
alter database new national character set WE8ISO8859P1
ORA-1507 signalled during: alter database new national character set WE8ISO88...
Shutting down instance (normal)
License high water mark = 1
Tue Sep 09 10:46:15 2003
ALTER DATABASE CLOSE NORMAL
ORA-1507 signalled during: ALTER DATABASE CLOSE NORMAL...
archiving is disabled
Starting up ORACLE RDBMS Version: 8.1.6.0.0.
System parameters with non-default values:
processes = 59
shared_pool_size = 52428800
large_pool_size = 614400
java_pool_size = 20971520
control_files = e:\ORacle\oradata\new\control01.ctl, e:\ORacle\oradata\new\control02.ctl, e:\ORacle\oradata\new\control03.ctl
db_block_buffers = 19200
db_block_size = 8192
compatible = 8.1.0
log_buffer = 32768
log_checkpoint_interval = 10000
log_checkpoint_timeout = 1800
db_files = 1024
db_file_multiblock_read_count= 8
max_enabled_roles = 30
remote_login_passwordfile= EXCLUSIVE
global_names = TRUE
distributed_transactions = 500
instance_name = new
service_names = new
mts_dispatchers = (PROTOCOL=TCP)(PRE=oracle.aurora.server.SGiopServer)
open_links = 4
sort_area_size = 65536
sort_area_retained_size = 65536
db_name = new
open_cursors = 100
os_authent_prefix =
job_queue_processes = 4
job_queue_interval = 10
parallel_max_servers = 5
background_dump_dest = e:\ORacle\admin\new\bdump
user_dump_dest = e:\ORacle\admin\new\udump
max_dump_file_size = 10240
oracle_trace_collection_name=
PMON started with pid=2
DBW0 started with pid=3
LGWR started with pid=4
CKPT started with pid=5
SMON started with pid=6
RECO started with pid=7
SNP0 started with pid=8
SNP1 started with pid=9
SNP2 started with pid=10
SNP3 started with pid=11
Tue Sep 09 10:46:30 2003
starting up 1 shared server(s) ...
starting up 1 dispatcher(s) for network address '(ADDRESS=(PARTIAL=YES)(PROTOCOL=TCP))'...
Tue Sep 09 10:46:31 2003
alter database mount
Tue Sep 09 10:46:34 2003
ORA-00202: controlfile: 'e:\ORacle\oradata\new\control01.ctl'
ORA-27041: unable to open file
OSD-04002: unable to open file
O/S-Error: (OS 2) The system cannot find the file specified.
Tue Sep 09 10:46:34 2003
ORA-205 signalled during: alter database mount...
Dump file e:\ORacle\admin\new\bdump\newALRT.LOG
Tue Sep 09 11:18:54 2003
ORACLE V8.1.6.0.0 - Production vsnsta=0
vsnsql=e vsnxtr=3
Windows 2000 Version 5.0 , CPU type 586
Starting up ORACLE RDBMS Version: 8.1.6.0.0.
System parameters with non-default values:
processes = 59
shared_pool_size = 52428800
large_pool_size = 614400
java_pool_size = 20971520
control_files = e:\ORacle\oradata\new\control01.ctl, e:\ORacle\oradata\new\control02.ctl, e:\ORacle\oradata\new\control03.ctl
db_block_buffers = 19200
db_block_size = 8192
compatible = 8.1.0
log_buffer = 32768
log_checkpoint_interval = 10000
log_checkpoint_timeout = 1800
db_files = 1024
db_file_multiblock_read_count= 8
max_enabled_roles = 30
remote_login_passwordfile= EXCLUSIVE
global_names = TRUE
distributed_transactions = 500
instance_name = new
service_names = new
mts_dispatchers = (PROTOCOL=TCP)(PRE=oracle.aurora.server.SGiopServer)
open_links = 4
sort_area_size = 65536
sort_area_retained_size = 65536
db_name = new
open_cursors = 100
os_authent_prefix =
job_queue_processes = 4
job_queue_interval = 10
parallel_max_servers = 5
background_dump_dest = e:\ORacle\admin\new\bdump
user_dump_dest = e:\ORacle\admin\new\udump
max_dump_file_size = 10240
oracle_trace_collection_name=
PMON started with pid=2
DBW0 started with pid=3
LGWR started with pid=4
CKPT started with pid=5
SMON started with pid=6
RECO started with pid=7
SNP0 started with pid=8
SNP1 started with pid=9
SNP2 started with pid=10
SNP3 started with pid=11
Tue Sep 09 11:18:57 2003
starting up 1 shared server(s) ...
starting up 1 dispatcher(s) for network address '(ADDRESS=(PARTIAL=YES)(PROTOCOL=TCP))'...
Tue Sep 09 11:18:58 2003
alter database mount exclusive
Tue Sep 09 11:19:01 2003
ORA-00202: controlfile: 'e:\ORacle\oradata\new\control01.ctl'
ORA-27041: unable to open file
OSD-04002: unable to open file
O/S-Error: (OS 2) The system cannot find the file specified.
Tue Sep 09 11:19:01 2003
ORA-205 signalled during: alter database mount exclusive...
Shutting down instance (abort)
License high water mark = 5
Instance terminated by USER, pid = 1156
Dump file e:\ORacle\admin\new\bdump\newALRT.LOG
Tue Sep 09 11:22:12 2003
ORACLE V8.1.6.0.0 - Production vsnsta=0
vsnsql=e vsnxtr=3
Windows 2000 Version 5.0 , CPU type 586
Starting up ORACLE RDBMS Version: 8.1.6.0.0.
System parameters with non-default values:
processes = 59
shared_pool_size = 52428800
large_pool_size = 614400
java_pool_size = 20971520
control_files = e:\ORacle\oradata\new\control01.ctl, e:\ORacle\oradata\new\control02.ctl, e:\ORacle\oradata\new\control03.ctl
db_block_buffers = 19200
db_block_size = 8192
compatible = 8.1.0
log_buffer = 32768
log_checkpoint_interval = 10000
log_checkpoint_timeout = 1800
db_files = 1024
db_file_multiblock_read_count= 8
max_enabled_roles = 30
remote_login_passwordfile= EXCLUSIVE
global_names = TRUE
distributed_transactions = 500
instance_name = new
service_names = new
mts_dispatchers = (PROTOCOL=TCP)(PRE=oracle.aurora.server.SGiopServer)
open_links = 4
sort_area_size = 65536
sort_area_retained_size = 65536
db_name = new
open_cursors = 100
os_authent_prefix =
job_queue_processes = 4
job_queue_interval = 10
parallel_max_servers = 5
background_dump_dest = e:\ORacle\admin\new\bdump
user_dump_dest = e:\ORacle\admin\new\udump
max_dump_file_size = 10240
oracle_trace_collection_name=
PMON started with pid=2
DBW0 started with pid=3
LGWR started with pid=4
CKPT started with pid=5
SMON started with pid=6
RECO started with pid=7
SNP0 started with pid=8
SNP1 started with pid=9
SNP2 started with pid=10
SNP3 started with pid=11
Tue Sep 09 11:22:15 2003
starting up 1 shared server(s) ...
starting up 1 dispatcher(s) for network address '(ADDRESS=(PARTIAL=YES)(PROTOCOL=TCP))'...
Tue Sep 09 11:22:16 2003
alter database mount exclusive
Tue Sep 09 11:22:19 2003
ORA-00202: controlfile: 'e:\ORacle\oradata\new\control01.ctl'
ORA-27041: unable to open file
OSD-04002: unable to open file
O/S-Error: (OS 2) The system cannot find the file specified.

Hi Kuljeet,
since you have a Windows system, I suggest you to open Windows explorer and check if all the 3 control files are there or not in the given location. It seems that your control01.ctl file is missing. If so then you have 2 options;
1. Delete the entry from the parameter file for this control file so that Oracle does not use this file at all.
OR
2. Shut down your database normally and then copy the control02.ctl or control03.ctl manually with the copy command and rename it to control01.ctl. If you follow this option you need not delete the control01.ctl entry from the parameter file. But note to copy the control file the database has to be shutdown normally.

Data is not updating in data target from PSA

Hi,
i have loaded data from flat file to an Info Object(with direct update)....the data is loaded correctly into PSA...when i manually read data from PSA to data target its not updting in data target.......can anyone help with this....thanks in advance..

hi bwusr,
direct update, so it's master data,
is it attribute or text ? perhaps there's invalid character or lower case,
check in monitor tab detail.
and when you said not updated to data target,
you check by right click 'maintain master data' ?
or you mean it's not updated to reporting ?
execute change run ? rsa1->tools->apply attribute/hierarchy change.
hope this helps.

Incopy files not updating

Having a problem with Incopy files not updating after designers on Indesign prepare packages on second round of revisions.
First, the designers create an Indesign file and prepare a newly created Incopy package. The editors are able to open the package for the first time. Editors make changes then repackage for designers. Designer then open package from editors and make necessary changes and then repackage back to the editors. At this point, the editors receive a message to replace when opening package. The files open but it doesn't update all the changes that was originally made to it. It as if it is still using the original assignments from the first newly created package. Also, all the assignments have "?" in the assignment window in Incopy. We are unable to figure out how to update the "?" in Incopy or relink or what ever we need to do at this point.
Several things we checked.
1. Unstuffing the package contents from the designers shows all updated file dates. So we know the package contains the newest updated assignment files.
2. If the designers rename the file names on all the assignments in the assignment folder, then repackage. The files open on Incopy with updated changes. But not if the file name remains the same. Also, if the assignment files are all renamed, it doesn't ask to replace anything on Incopy.
At this point. Our only solution is to rename all the assignment files and repackage. But we shouldn't have to be doing this, especially since it adds time to the designers to repackage the files.
Designers using Indesign CS 3 on Mac OS 10.6.4.
Editors using Incopy CS 3 on PC Windows.
Any help would be greatly appreciated.

When the InCopy user opens the assignment package for the first time, it unpacks (it's really like a .zip file) into a folder on their hard drive called InCopy Assignments. The folder is located in My Documents on a PC and in the Home > Documents folder on a Mac.
Every unpacked InCopy assignment package goes into a subfolder within this InCopy Assignments parent folder. Each package's folder is named after the *assignment* name (not the name of the package itself, which is usually the same but not always). So if the assignment name is Chapter1.inca, then the subfolder name will be Chapter1.
When the InCopy user repackages it for the designer, it packages a *copy* of this subfolder. This is the subfolder that Bob is suggesting they delete, after sending off the packaged InDesign file. That's a good idea.
If you can't rely on your editors to do that ... many are very leery of throwing anything away ... then your designers should *rename the assignment* in their Assignments panel before creating an InCopy package for the second or third or whatever time. They can just double-click the assignment in the panel, the Assignment Options dialog box opens, and they can change the name from say "Chapter1" to "Chapter1-v2". They click okay, they choose Package for InCopy, and send it off.
When the editor gets this file and double-clicks it, it unpacks into a different subfolder than before: Chapter1-v2, leaving the Chapter1 subfolder intact. So you avoid the prob of duplicate assignments on the InCopy user's hard drive.
FWIW this was much more of a glitch with CS3. Not sure what Adobe did differently, but assignment packages are much more intelligent in CS4 and CS5.
AM

Just upgraded my workstation and render nodes to AE CC 2014 and now I receive a "render control file not valid" upon rendering out.

I just upgraded my workstation and render farm to AE CC 2014 and now I receive a "render control file not valid" on my render nodes when I try and render out an image sequence. Any ideas why the update would cause this? All my machines are updated to the latest version of AE CC 2014. Thanks!

Sorry I meant "Update". I was using AE CC, Installed AE CC 2014 on all my machines recently.

Keynote document saved in icloud not updating with data from Numbers? is icloud the problem

keynote document saved in icloud not updating with data from Numbers? is icloud the problem.
If both files are held locally on the computer it looks like there is no problem however if you try and do it though icloud (ie your docs are saved on icloud) you dont get the "source" oprion besides the graph etc. Is this a but or a broken function due to the new implementation of icloud.

Hi sebnor31,
This is Visual C# forum, but your question seems not related to Visual C# language itself. It most likely related to the bluetooth message transaction protocal or with the device itself.
I'll move your question to [where is this forum for...] forum where the morderator may direct you to the correct forum.
Thanks for your understanding.
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

PC Sync could not update the data to the mobile ph...

Ok now I am a little annoyed with my Nokia 6680.
For the last four months it has been working fine but all of a sudden it has stopped synching with either of my PC's.
The phone connects ok and I can do file transfers etc however when I try to sync it fails with the message
"The Synchronisation has been Terminated!"
and
"PC Sync could not update the data to the mobile phone."
I updated PC Sync to latest version on both PC's and I have tried cable and bluetooth connections but get the same issue.
In the end I bit the bullet and re-initialised the phone and it began working again.... for three days and then its doing the same thing again. It still connects ok but no sync.
My Laptop is using WinXP SP2 and my home PC is on WinXP SP1.
Anyone able to help with this please, my phone is effectively now a paper weight and I will go back to Pocket PC phones again.

Thanks for the tip I had the SAME problem on the 6822 same error. The phone had been fine for a month or so. Then nothing would synch, thought it was the PC fixed / reinstalled the software changes options nothing would work same error.
Read your note, powered down the phone and Bingo all synched fine!
Thanks very much. I'm using a Nokia 6822

View the .rtf file not display the data in BI Publisher Enterprise.

Hi,
Platform: OBIEE 10g in NT XPsp2
View the .rtf file not display the data in BI Publisher Enterprise.
Step 1, I created Answer-request, create .rtf file with Word and add the request name, Add bar chart and table, preview PDF is working fine with data, Upload this template to Answers, View Template from Answer is working fine with data.
Step 2, Answers – More Products > BI Publisher > My Folders > Create a new report > Edit > Data Model > New > Type: SQL Query > Data Source: Oracle BI EE > Query Builder > from SupplierSales assign Customer, Periods, Sales Facts (select Region, state, Year, Units Shipped) > Results > Save > Save
Click Layouts > New > enter Name ….. > Click Layouts > borrows .rtf file in Manage T file > Upload > Save > Click View
It is showing only the .rtf file without data. Why there is no data?
Please guide me to solve this issue.
Thanks,
Jo

Thanks for you reply,
Our scenario is this report is basically a dissconnected mode report... we are developing these reports for mobile clients.
We dint face this kind of issue while developing other reports.
So please let us know if you have any idea on why we are facing this issue.
Regards,
Maneesh

Watch folder "render control file not valid"

I'm using cc 2014 on my main workstation and render nodes. I can't get the render engine to accept a job because I get the "render control file not valid" error when setting the watch folder. But, I can use the render engine on my main workstation and the job will start just fine. That leads me to believe its a permissions problem, but all of my network computers are set up to work as a 3d animation render farm and it all works pretty well with all computers being able to read and write to each other with full permissions.
Is there anything else I can look at that might help? Thanks in advance.

> "Hello - is there any one left at Adobe to help with this? "
This is a user-to-user forum, where people help out in their free time. If you want a guaranteed response from Adobe personnel, contact Adobe Technical Support:
http://www.adobe.com/support/contact

HT204073 I had purchase one year protection plan but it is not updated till today how would I updated iPhone warranty my self

I had purchase one year protection plan but it is not updated till today how would I updated iPhone warranty my self

Does the iPod connect to other networks?
Does the iPod see the network?
Any error messages?
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar
maybe this:
iOS: Wi-Fi or Bluetooth settings grayed out or dim
If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
Apple Retail Store - Genius Bar

WSA Webroot Malware Category DAT files Not Updating

I have two wsa's that have not updated their webroot dat files since may 16th. I have tried a manual update and it still has not updated. I am not sure if any new updates have been released and availalbe. Is there a way I can verify what the most recent dat files are??

Did you ever resolve this issue. I have the webroot failing to update aswell. Will log a TAC case, but checking to see if you have had any progress?
Ben

CSS files not updating correctly

I'm having some trouble with the css files that are uploaded throught the application builder. When uploading an update to an existing css file, the file is not updated in the browser. Even after closing all browser windows and deleting the temporary internet files the new version is not loaded. I've even tried deleting the file from the app builder and holding the control key down when refreshing the browser and it still loads as if one existed. We currently have 3 seperate server environments and it works fine on 2 out of the 3...could this be a setting on the application server when the file is fetched from the database? It is currently calling:
wwv_flow_file_mgr.get_file?p_security_group_id=721404936311769&p_fname=iPRACA.css
I know the correct file is being uploaded to the database because when I view the detailed report in the application builder and click on the file name, the updated version is displayed in the text area. But, when I click on the download icon and open the css file to view, it is still the old version.
I'm currently using APEX version 2.3 and OAS 10.1.2
Any help would be greatly appreciated.

Hi YodaHart,
What happens when you rename your css?
Does it work then?
I also guess it's the Oracle AS. However we should investigate further on what you're thinking.
If you query WWV_FLOW_FILE_OBJECTS$ you still see the files while you don't see them in APEX anymore? If yes, I would create another table as select of the WWV_FLOW_FILE_OBJECTS$ table, just to have a backup. If the files aren't used anymore, you should be save by deleting the corresponding old records (for ex through SQLPLUS). After all, these are files you uploaded...
Thanks,
Dimitri

Relinked picture files not updating

Hi all,
To begin with, I am using final cut pro 10.0.8 on mountain lion 10.8.4.
The problem I'm having is that my media files are not updating in final cut pro x once they have been changed outside final cut pro. I'll explain what I'm doing:
1. I have imported some png files into my events and chose not to copy to my events folder. These picture files are used extensively in my project.
2. I have found that I need to make some changes to the png files. After making the changes in photoshop (the original file is psd and I save to png), final cut pro does not automatically update the new details even though when I click the event and choose reveal in finder, it takes me to the newly saved file that does have the changes. The file name and location did not change.
3. I then tried to manually relink the files, but it still does not update the new changes. What is interesting is that the info on the picture still refers back to the orginal details when the file was created. Again if I choose reveal in finder, it highlights the newly saved png.
4. I then decided to delete the original png file and empty the trash can. Final cut shows that the media is missing. I saved the png from photoshop again and final cut pro automatically relinked the file, but it is still the old image!
5. As a last resort, I trashed the original image again, resaved the png with a different name, relinked again. This time final cut updates the date it was created, but the image is still the old image!
No matter what I try to do, I can't get final cut pro to update the image. I dropped the png into the timeline and did and export hoping it was just displying the original image but would use the new image when it renders. Unfortunately, the movie it created had the old image still.
Obviously the image the event is pointing to is not the one it is using because I have double checked that the file saved has been updated outside of final cut. Is there something I am doing wrong? Or is there a bug with final cut pro? I'm suspecting it is using a chached file somewhere.
Thanks for your help,
Adrian

Tom, I followed your suggestion and final cut updated the png in the event viewer the first time, but refused to update any further changes I made. So I deleted the entire event, created a new one, and imported a new picture with different name, and could not get it to update again.
What is crazy is when I right-click on it in the event viewer and choose Reveal in Finder, finder shows the updates I made.
Now obviously this would not be suitable in my case, as I can't edit the png file since it has been flattened. I need to work on the photoshop file and then save over th png file. Surely I should be able to save over my png file (when I save as from photoshop) and final cut should see the changes.
Rgarding your question, the pictures I have are different angles of an office scene which will be my background for me green screen shots. I had to tweek a few parts of it and only then found that final cut didn't want to update them. Now that I have this problem, I don't want to continue any further until this is sorted out incase I have to make more changes.
I've only had this new computer for 8 days, so final cut has not been installed for long. But since no one else is having this proble, I'll trash final cut and download it again. Hopefully that will solve the problem.

How to pass parameters to the Control file while loading the data from flat file to staging table

Thanks in advance

Hi ,
LOADDATA statement is required at the beginning of the control file.
INFILE: INFILE keyword is used to specify location of the datafile or datafiles.
INFILE* specifies that the data is found in the control file and not in an external file. INFILE ‘$FILE’, can be used to send the filepath and filename as a parameter when registered as a concurrent program.
INFILE ‘/home/vision/kap/import2.csv’ specifies the filepath and the filename.
Hope this will help you......

Control file not updated till date in RAC two node database

Similar Messages

Maybe you are looking for