Convert "1D array of dynamic data" to "Dynamic data" after auto-indexing with loop

Hi -
I have a question about how exaclty auto-indexing works with the Dynamic Data type when exiting a while loop. I'd like to use the DAQ assistant to record data through an analog input (on the MyDAQ) and then replay that data through an analog output. This works fine if I use the DAQ Assistant to record data for a set amount of time:
However, I run into trouble when I try to use a While loop with a stop button to record data for an arbitrary amount of time. I set the dynamic data tunnel out of the While loop to "Indexing", but then when it exits the loop, it becomes "1-D Array of Dynamic Data" instead of just "Dynamic Data", and get a broken wire when I try to connect it to the input of the DAQ Assistant. I've also tried converting the dynamic data to Array and Waveform data types inside the loop, but have the same issue (they become 2D Array and 2D Array of Waveform respectively when leaving the loop). Try as I might using blocks like Convert to/from Dynamic Data Type, or Array Subset, I'm unable to get them back down to just Dynamic Data or Waveform, which will be accepted by the DAQ Assistant:
One other small note - I'm not sure if using the "Build Array" function with a shift register accomplishes exactly the same thing as just auto-indexing an array out of the loop - so I've tried both, but still have the broken wire issue.
I'm assuming this is just a simple issue of using the right block to convert "1D Array of [Something]" to just plain [Something]. Any help appreciated.
Attachments:
PWM_FlatSequence.vi ‏101 KB
PWM_FlatSequence_While.vi ‏129 KB

I have been facing problem for all temperature values placing the Write to Measurement File outside the Loop.
In Error message it says" Source: 1D array of dynamic data and Sink: Dynamic data".
Is there any means of convering 1D array of dynamic data to dynamic data?
I would highly appreciate any help.
Attachments:
Temperature Logger.vi ‏110 KB

Similar Messages

Array Size doesn't work correctly after "Auto-indexed Tunnel"

Array Size returns value even if Empty Array is detected after "Auto-indexed Tunnel" tha generates 2D array.
See example + VI with correct output as I expected.
OR
There is problem with generating 2D array --- It's empty. 1D array is generated in right way. 100 x 0 but not Emptu Array.
Attachments:
ArraySize_Bug.vi ‏9 KB
ArraySize_Corrected.vi ‏19 KB

Not a bug. This is correct behavior that is consistent with other parts of LabVIEW.
The decision to handle multi-dimensional arrays like this was made long ago and is an enshrined part of the LabVIEW language spec. It will not be changed.

Dynamic Link for Premiere and After Effects CS4 with Titles

I've created a Rolling Title in Premiere Pro CS4. I'd like to create a Dynamic Link to bring the title into After Effects CS4 to add effects that will show up in Premiere. I've watched a few video tutorials on Dynamic Link and read the documentation and tried a variety of permutations but can't seem to get this done.
Also saw something in these forums about problems using Dynamic Link with Titles (as opposed to regular clip??)
And something about Premiere and After Effects projects being saved together ??in same folder - is that correct?
So, could someone explain if this can be done and the right way to do it?
Thanks

Thanks Mylenium - appreciate the quick and focused reply.
I would like to keep the benefits of the Premiere Pro Titler (to play with the length of time by stretching or squashing the Title block on the timeline; to type in time to stay on screen at end; ease in and out etc . . .). If I do render out a png / tiff / or psd sequence with alpha, and bring that into AFX to play with. Will I still retain the ability to use the Titler features in Premire Pro, or do I essentially have to convert it to 'regular footage' on reimport as opposed to a 'Title?"
Thanks

How to delete all previous icloud data from current icloud after sighning in with the current icloud account

so i sighned into someone elses device with the current icloud account and i sighned out. Some of the icloud data from the other device is now on mine. All i want to know is how to delete all the icloud data in my current icloud account from the other icloud account

Hello ,
I had the same problem and i have done everything manually.
It's a shame that Apple doesn't put a "Reset to factory Settings" button or simply "Delete all data from iCloud.com". That way, it would be much simpler for everyone including myself.
Winston Churchill is right unfortunately . Happy deleting !
Kind Regards,
Moonburn

Capture data in 1D barcode upon merging XML with XDP?

Hi,
The scenario is:
Forms Server 7.2.2 is being used for merging XML data with an XDP file to render a PDF (displaying a pre-filled form to user).
On the XDP, there is a 1D Barcode and few fields are mapped to this barcode (the barcode is intended to capture form identification information).
Upon merging, the barcode should capture the data of those fields (data is being fetched from a db and fed as XML to Forms server). This is required as the pre-filled form will be printed and then mailed to another location, where the barcode will be read using a decoder to capture form indentification.
Will the 1D barcode captures data from those fields, after merging XML with XDP?
The form is NOT Reader Extended. Is Reader Extending a necessity for enabling 1D barcode to capture data?
Is this also applicable for 2D barcodes?
Thanks a lot for your help! :)

Thank you Hodmi,
I had forgotten to define the Record name parameter in the PDF Output Options.
As the XML structure changed, not upating this parameter was preventing the process from working.
Now it is working just fine. Thank you!
Marcos

Can I display XY Graph data as Dynamic Data?

Hi all,
I have an application that treats XY Data, i.e. data with the X axis
gaps not constant (because the trigger is external and it has the
interval not constant), and I would like to use some of the utilities
related to Dynamic Data. I don't know if that's possible but I suspect
that Dynamic Data must have constant X axis gaps. Can anyone confirm
that point? Or the possibility of transforming that data? How could I
do that?

If you already have the data as two separate arrays (an x array, and a y array), then just use the XY Graph and a bundle node to plot it. If you want to use the Dynamic Data type that was introduced in LV 7, then just use the To DDT conversion bullet. You can also use an interpolate routine to "shift" the x values around, but it doesn't sound like you want to do that.
J

Add a data series dynamically in charts

I am trying to add a data series dynamically in a chart but
it does not seems to work. Here is the sample code. Any idea?
var line1:LineSeries=new LineSeries();
line1.dataProvider=[something];
line1.displayName="New data";
chart.secondSeries.push(line1);
It works if I do the following but I don't want to remove
other series already there.
var arr = new Array();
chart.secondSeries=arr;
var line1:LineSeries=new LineSeries();
line1.dataProvider=[something];
line1.displayName="New data";
arr.push(line1);

I see...i don't know why the chart is not refreshing itself
in the next keyframe after you added another series. You can also
try to put the statement:
[myChart.series[(myChart.series as Array).length] = your new
ColumnSeries object goes here.]
in a new frame by doing doLater();
Apparently an asigninment statement on the series array does
the trick. If you don't like that approach, you can also try to
invalidate the display object, so that a refresh is forced.
-george

How to display dynamic datas and double datas (chart)

Hi all !
I would like to display dynamic datas and double datas by using charts.
However, it doesn't work and I don't understand why.
Can you help me to fix that ?
Best regards,
- John
Attachments:
double_dynamics_data.vi ‏54 KB

Hi John,
the sine looks like it should look with your VI!
You convert the DDT to a scalar DBL. That conversion will only use the first sample of the generated sine waveform - usually this is always the same (offset) value when you generate full periods… Or to put it in a mathematical expression: sin(0°)+4 = 4!
When you want to display waveform you should work with waveforms!
Actually, I have used Dynamic data type in order to simulate an signal.
Well, I also simulated a signal in my example VI. I didn't use any ExpressVI to do so…
In a few weeks, I will receive a sensor. I will use in LabView 'DAQ Assistant' whose the ouput is a Dynamic Data.
Nobody forces you to use the DAQAssistent ExpressVI. There are nice DAQmx functions available and LabVIEW comes with a lot of ready-to-use example VIs…
That's why, I used in first place, the 'Simulate signal'. So I think I should keep Dynamic Data Type
I do think you don't need to use the DDT. I think it's better to understand what is going on in your VI. And I think the DDT will be no help for you…
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Conversion from dynamic to double bit data

This might be very simple but I've got confused. I have current data and average data as in code. I want to build array using this data, save it on my hard-disk and open in word with headers(current and average)
Problems:
I input data from both sources into build array as shown, and wire output of build array to write to spreadsheet vi. I get error source is dynamic and sink is double bit. This is the hardest part of my life to figure out which conversion pallete to use.
When I run the vi (lets assume correct conversion pallete is wired and there's no conversion error,) dialog box pops up for file path which keeps coming on
Ideally I would like it to pop up on screen when I press run so that I may browse location to save file and once path is specified vi runs continuously and data is written on spreadsheet while vi is running.
Many thanks for reading and help
Cheers
Solved!
Go to Solution.
Attachments:
creating 2d array and saving data in spreadsheet.vi ‏109 KB

Last time I didn't even try to think about what you were doing. Now that I look at it I am once again reminded why I don't use express VIs and dynamic data types, but I digress. I am now guessing that you would like to average a signal and have two curves, the current set and a weighted average.
There may or may not be a way to do this with Express VIs and Dynamic Data types. To be honest, if there is I wouldn't use it. What I would do as a start is immediately following each Express VI insert a Dynamic Data to DBL conversion and then Index Array to get the first row. Now you are working with 1D arrays.
Attachments:
creating 2d array and saving data in spreadsheet_MOD2.vi ‏149 KB

How to populate data in dynamic internal table

Hi Expert,
fyi. My dynamic internal table field is created base on data selected. Eg. select table qpcd has 5 records. These 5 recods will become fieldname to my dynamic internal table. My dynamic internal table will be
...itab
      01
      02
      03
      04
      05
The 5 records from qpcd is populated in another table call viqmel. I need to find the occurance of each code in viqmel and populate the number of occurance in itab in each of column. The final dynamic itab will be like this
table itab
01       02     03    04     05   -
> field name
2         0        1     0       1    -
> data
my source code like below
Report ZPLYGRND2.
TABLES: mara, makt.
TYPE-POOLS: slis, sydes.
DATA:it_fcat TYPE slis_t_fieldcat_alv,
     is_fcat LIKE LINE OF it_fcat,
     ls_layout TYPE slis_layout_alv.
DATA: it_fieldcat TYPE lvc_t_fcat,
      is_fieldcat LIKE LINE OF it_fieldcat.
DATA: new_table TYPE REF TO data,
      new_line TYPE REF TO data,
      ob_cont_alv TYPE REF TO cl_gui_custom_container,
      ob_alv TYPE REF TO cl_gui_alv_grid,
      vg_campos(255) TYPE c,
      i_campos LIKE TABLE OF vg_campos,
      vg_campo(30) TYPE c,
      vg_tables(60) TYPE c.
types : begin of t_qpcd,
         codegruppe like qpcd-codegruppe,
         code like qpcd-code,
        end of t_qpcd.
data:wa_qpcd type t_qpcd,
     i_qpcd type standard table of t_qpcd initial size 0.
FIELD-SYMBOLS: <l_table> TYPE table,
               <l_line> TYPE ANY,
               <l_field> TYPE ANY.
select * into corresponding fields of wa_qpcd from qpcd
where katalogart = 'D'
and   codegruppe = 'OOT01'.
append wa_qpcd to i_qpcd.
endselect.
loop at i_qpcd into wa_qpcd.
is_fcat-fieldname = wa_qpcd-code.
APPEND is_fcat TO it_fcat.
endloop.
LOOP AT it_fcat INTO is_fcat.
    is_fieldcat-fieldname = is_fcat-fieldname.
    is_fieldcat-ref_field = is_fcat-ref_fieldname.
    is_fieldcat-ref_table = is_fcat-ref_tabname.
    APPEND is_fieldcat TO it_fieldcat.
ENDLOOP.
*... Create the dynamic internal table
CALL METHOD cl_alv_table_create=>create_dynamic_table
    EXPORTING
        it_fieldcatalog = it_fieldcat
    IMPORTING
        ep_table = new_table.
if sy-subrc = 0.
endif.
*... Create a new line
ASSIGN new_table->* TO <l_table>.
CREATE DATA new_line LIKE LINE OF <l_table>.
ASSIGN new_line->* TO <l_line>.
LOOP AT <l_table> INTO <l_line>.
ENDLOOP.

hello dear i m giving u a code in this a dynamic table is made on the basis of table in database , and u can download this data correct it , see it, or even change it....and upload in tht table help full if u dont know the table name...in advance.
also the code to populate data in dynamic table is in this code like:
SELECT * FROM (MTABLE_N)
INTO CORRESPONDING FIELDS OF TABLE <FS_ITAB> .
look at the whole program .hope this solve ur problem thanks.
REPORT ZTESTA MESSAGE-ID ZIMM    .
TYPES : DATA_OBJECT TYPE REF TO DATA.
DATA : MITAB TYPE REF TO DATA .
TYPE-POOLS : SLIS .
DATA : IT_FIELDCAT TYPE STANDARD TABLE OF SLIS_FIELDCAT_ALV
WITH HEADER LINE .
DATA : IT_FIELDCATALOG TYPE LVC_T_FCAT .
DATA : WA_FIELDCATALOG TYPE LVC_S_FCAT .
DATA : I_STRUCTURE_NAME LIKE DD02L-TABNAME .
DATA : I_CALLBACK_PROGRAM LIKE SY-REPID .
DATA : DYN_LINE TYPE DATA_OBJECT .
FIELD-SYMBOLS : <FS_ITAB> TYPE STANDARD TABLE .
DATA : TABLE_NAME_IS_VALID TYPE C .
DATA : DYNAMIC_IT_INSTANTIATED TYPE C .
CONSTANTS BUTTONSELECTED TYPE C VALUE 'X' .
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT 5(29) T_TABL.
PARAMETERS : MTABLE_N LIKE RSRD1-TBMA_VAL
MATCHCODE OBJECT DD_DBTB_16 OBLIGATORY .
DATA CHECKTABLED.
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT 5(29) T_FILE.
PARAMETERS : MFILENAM LIKE RLGRAP-FILENAME .
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT 5(29) T_DOWN.
PARAMETERS : P_DOWNLD RADIOBUTTON GROUP GRP1
USER-COMMAND M_UCOMM .
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT 5(29) T_CHKF.
PARAMETERS : P_CHKFIL RADIOBUTTON GROUP GRP1 .
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT 5(29) T_UPLD.
PARAMETERS : P_UPLOAD RADIOBUTTON GROUP GRP1 .
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT 5(29) T_SHOW.
PARAMETERS : P_SHOW_T RADIOBUTTON GROUP GRP1 .
SELECTION-SCREEN END OF LINE.
AT SELECTION-SCREEN OUTPUT .
PERFORM CHECK_FILENAME .
AT SELECTION-SCREEN.
IF SY-UCOMM = 'ONLI'.
    CHECKTABLED = MTABLE_N+0(1).
    IF CHECKTABLED NE 'Z'.
      MESSAGE I017.
      LEAVE TO SCREEN 1000.
    ENDIF.
    IF SY-UNAME NE 'KAMESH.K'.
      MESSAGE I023 WITH SY-UNAME.
      LEAVE TO SCREEN 1000.
    ENDIF.
ENDIF.
IF SY-UCOMM = 'PRIN'.
    CHECKTABLED = MTABLE_N+0(1).
    IF CHECKTABLED NE 'Z'.
      MESSAGE I017.
      LEAVE TO SCREEN 1000.
    ENDIF.
    IF SY-UNAME NE 'KAMESH.K'.
      MESSAGE I023 WITH SY-UNAME.
      LEAVE TO SCREEN 1000.
    ENDIF.
ENDIF.
AT SELECTION-SCREEN ON VALUE-REQUEST FOR MFILENAM .
PERFORM F4_FOR_FILENAME .
INITIALIZATION .
T_TABL = 'Table Name' .
T_FILE = 'File Name' .
T_DOWN = 'Download Table' .
T_CHKF = 'Check File to Upload' .
T_UPLD = 'Upload File' .
T_SHOW = 'Show Table Contents' .
START-OF-SELECTION .
PERFORM CHECK_TABLE_NAME_IS_VALID .
END-OF-SELECTION .
IF TABLE_NAME_IS_VALID EQ ' ' .
    MESSAGE I398(00) WITH 'INVALID TABLE NAME' .
ELSE .
    PERFORM INSTANTIATE_DYNAMIC_INTERNAL_T .
    CHECK DYNAMIC_IT_INSTANTIATED = 'X' .
    CASE BUTTONSELECTED .
      WHEN P_DOWNLD .
        PERFORM SELECT_AND_DOWNLOAD .
      WHEN P_CHKFIL .
        PERFORM CHECK_FILE_TO_UPLOAD .
      WHEN P_UPLOAD .
        PERFORM UPLOAD_FROM_FILE .
      WHEN P_SHOW_T .
        PERFORM SHOW_CONTENTS .
    ENDCASE .
ENDIF .
FORM CHECK_TABLE_NAME_IS_VALID.
DATA MCOUNT TYPE I .
TABLES DD02L .
CLEAR TABLE_NAME_IS_VALID .
SELECT COUNT(*) INTO MCOUNT FROM TADIR
WHERE PGMID = 'R3TR'
AND OBJECT = 'TABL'
AND OBJ_NAME = MTABLE_N .
IF MCOUNT EQ 1 .
    CLEAR DD02L .
    SELECT SINGLE * FROM DD02L WHERE TABNAME = MTABLE_N .
    IF SY-SUBRC EQ 0.
      IF DD02L-TABCLASS = 'TRANSP' .
        TABLE_NAME_IS_VALID = 'X' .
      ENDIF .
    ENDIF.
ENDIF .
ENDFORM. " CHECK_TABLE_NAME_IS_VALID
FORM SELECT_AND_DOWNLOAD.
CLEAR : <FS_ITAB> .
SELECT * FROM (MTABLE_N)
INTO CORRESPONDING FIELDS OF TABLE <FS_ITAB> .
PERFORM CHECK_FILENAME.
CALL FUNCTION 'WS_DOWNLOAD'
       EXPORTING
            FILENAME                = MFILENAM
            FILETYPE                = 'DAT'
       TABLES
            DATA_TAB                = <FS_ITAB>
       EXCEPTIONS
            FILE_OPEN_ERROR         = 1
            FILE_WRITE_ERROR        = 2
            INVALID_FILESIZE        = 3
            INVALID_TYPE            = 4
            NO_BATCH                = 5
            UNKNOWN_ERROR           = 6
            INVALID_TABLE_WIDTH     = 7
            GUI_REFUSE_FILETRANSFER = 8
            CUSTOMER_ERROR          = 9
            OTHERS                  = 10.
IF SY-SUBRC EQ 0.
    MESSAGE I398(00) WITH 'Table' MTABLE_N
    'successfully downloaded to '
    MFILENAM .
ENDIF.
ENDFORM. " SELECT_AND_DOWNLOAD
FORM UPLOAD_FROM_FILE.
DATA : ANS TYPE C .
DATA : LINES_OF_ITAB TYPE I .
DATA : MSY_SUBRC TYPE I .
CALL FUNCTION 'POPUP_TO_CONFIRM_STEP'
       EXPORTING
            TEXTLINE1 = 'Are you sure you wish to upload'
            TEXTLINE2 = 'data from ASCII File to DB table '
            TITEL     = 'Confirmation of Data Upload'
       IMPORTING
            ANSWER    = ANS.
IF ANS = 'J' .
    PERFORM CHECK_FILENAME.
    CLEAR MSY_SUBRC .
    CALL FUNCTION 'WS_UPLOAD'
         EXPORTING
              FILENAME                = MFILENAM
              FILETYPE                = 'DAT'
         TABLES
              DATA_TAB                = <FS_ITAB>
         EXCEPTIONS
              CONVERSION_ERROR        = 1
              FILE_OPEN_ERROR         = 2
              FILE_READ_ERROR         = 3
              INVALID_TYPE            = 4
              NO_BATCH                = 5
              UNKNOWN_ERROR           = 6
              INVALID_TABLE_WIDTH     = 7
              GUI_REFUSE_FILETRANSFER = 8
              CUSTOMER_ERROR          = 9
              OTHERS                  = 10.
    MSY_SUBRC = MSY_SUBRC + SY-SUBRC .
    IF SY-SUBRC EQ 0.
      DESCRIBE TABLE <FS_ITAB> LINES LINES_OF_ITAB .
      IF LINES_OF_ITAB GT 0 .
        MODIFY (MTABLE_N) FROM TABLE <FS_ITAB> .
        MSY_SUBRC = MSY_SUBRC + SY-SUBRC .
      ENDIF .
    ENDIF.
    IF MSY_SUBRC EQ 0 .
      MESSAGE I398(00) WITH LINES_OF_ITAB
      'Record(s) inserted in table'
      MTABLE_N .
    ELSE .
      MESSAGE I398(00) WITH
      'Errors occurred No Records inserted in table'
      MTABLE_N .
    ENDIF .
ENDIF .
ENDFORM. " UPLOAD_FROM_FILE
FORM F4_FOR_FILENAME.
CALL FUNCTION 'WS_FILENAME_GET'
       EXPORTING
            DEF_PATH         = 'C:\'
            MASK             = ',.,..'
            MODE             = '0'
       IMPORTING
            FILENAME         = MFILENAM
       EXCEPTIONS
            INV_WINSYS       = 1
            NO_BATCH         = 2
            SELECTION_CANCEL = 3
            SELECTION_ERROR = 4
            OTHERS           = 5.
ENDFORM. " F4_FOR_FILENAME
FORM CHECK_FILENAME.
IF MFILENAM IS INITIAL
AND NOT ( MTABLE_N IS INITIAL )
AND P_SHOW_T NE BUTTONSELECTED.
    CONCATENATE 'C:\'
    MTABLE_N '.TXT' INTO MFILENAM.
ENDIF .
ENDFORM. " CHECK_FILENAME
FORM INSTANTIATE_DYNAMIC_INTERNAL_T.
CLEAR DYNAMIC_IT_INSTANTIATED .
I_STRUCTURE_NAME = MTABLE_N .
CLEAR IT_FIELDCAT[] .
CALL FUNCTION 'REUSE_ALV_FIELDCATALOG_MERGE'
       EXPORTING
            I_STRUCTURE_NAME       = I_STRUCTURE_NAME
       CHANGING
            CT_FIELDCAT            = IT_FIELDCAT[]
       EXCEPTIONS
            INCONSISTENT_INTERFACE = 1
            PROGRAM_ERROR          = 2
            OTHERS                 = 3.
IF SY-SUBRC EQ 0.
    LOOP AT IT_FIELDCAT .
      CLEAR WA_FIELDCATALOG .
      MOVE-CORRESPONDING IT_FIELDCAT TO WA_FIELDCATALOG .
      WA_FIELDCATALOG-REF_FIELD = IT_FIELDCAT-FIELDNAME .
      WA_FIELDCATALOG-REF_TABLE = MTABLE_N .
      APPEND WA_FIELDCATALOG TO IT_FIELDCATALOG .
    ENDLOOP .
    CALL METHOD CL_ALV_TABLE_CREATE=>CREATE_DYNAMIC_TABLE
    EXPORTING
    IT_FIELDCATALOG = IT_FIELDCATALOG
    IMPORTING
    EP_TABLE = MITAB .
    ASSIGN MITAB->* TO <FS_ITAB> .
    DYNAMIC_IT_INSTANTIATED = 'X' .
ENDIF.
ENDFORM. " INSTANTIATE_DYNAMIC_INTERNAL_T
FORM SHOW_CONTENTS.
CLEAR : <FS_ITAB> .
SELECT * FROM (MTABLE_N)
INTO CORRESPONDING FIELDS OF TABLE <FS_ITAB> .
I_CALLBACK_PROGRAM = SY-REPID .
CALL FUNCTION 'REUSE_ALV_LIST_DISPLAY'
       EXPORTING
            I_CALLBACK_PROGRAM = I_CALLBACK_PROGRAM
            IT_FIELDCAT        = IT_FIELDCAT[]
       TABLES
            T_OUTTAB           = <FS_ITAB>
       EXCEPTIONS
            PROGRAM_ERROR      = 1
            OTHERS             = 2.
ENDFORM. " SHOW_CONTENTS
FORM CHECK_FILE_TO_UPLOAD.
PERFORM CHECK_FILENAME.
CALL FUNCTION 'WS_UPLOAD'
       EXPORTING
            FILENAME                = MFILENAM
            FILETYPE                = 'DAT'
       TABLES
            DATA_TAB                = <FS_ITAB>
       EXCEPTIONS
            CONVERSION_ERROR        = 1
            FILE_OPEN_ERROR         = 2
            FILE_READ_ERROR         = 3
            INVALID_TYPE            = 4
            NO_BATCH                = 5
            UNKNOWN_ERROR           = 6
            INVALID_TABLE_WIDTH     = 7
            GUI_REFUSE_FILETRANSFER = 8
            CUSTOMER_ERROR          = 9
            OTHERS                  = 10.
IF SY-SUBRC EQ 0.
    I_CALLBACK_PROGRAM = SY-REPID .
    CALL FUNCTION 'REUSE_ALV_LIST_DISPLAY'
         EXPORTING
              I_CALLBACK_PROGRAM = I_CALLBACK_PROGRAM
              IT_FIELDCAT        = IT_FIELDCAT[]
         TABLES
              T_OUTTAB           = <FS_ITAB>
         EXCEPTIONS
              PROGRAM_ERROR      = 1
              OTHERS             = 2.
ENDIF .
ENDFORM. " CHECK_FILE_TO_UPLOAD
Message was edited by:
        SAURABH SINGH
        SENIOR EXECUTIVE
        SAMSUNG INDIA ELECTRONICS LTD.,NOIDA

How to delete data from dynamic internal table

Hi,
I have dynamic internal table and I have some slection screen fields , using these selection screen fields
(select -options), I have to filter the data? assigning will work with READ , but I have select options not the parametre,
and also delete will not work for dynamic table..
as we cannot use assigning with delete..
So how to do this?
and one more thing is , I cannot filter the data while selection( in select, I cannot filter the data-> as it's not coming directly from table, it's coming from buffer),
so now after selection of data, I need to filter the data from dynamic table.
Is there any way to do this?
Regards,
Mrunal

Hi matt,
I tried with below code as you said. But I am getting dump. can you help?
here is my piece of code.
FIELD-SYMBOLS: <LS_DATA> type any,
                           <LT_DATA> TYPE table,
                            <L_FIELD> type any.
    ASSIGN <l_buffer_entry>-dataptr->* TO <LS_DATA>.
    ASSIGN <l_buffer_entry>-dataptr->* TO <LT_DATA>.
LOOP AT <LT_DATA> ASSIGNING <LS_DATA>.
ASSIGN COMPONENT 'BUKRS' OF STRUCTURE <LS_DATA> TO <L_FIELD>.
IF <L_FIELD> NOT IN SO_BUKRS.
DELETE <LT_DATA>.
ENDIF.
UNASSIGN <L_FIELD>.
ASSIGN COMPONENT 'BELNR' OF STRUCTURE <LS_DATA> TO <L_FIELD>.
IF <L_FIELD> NOT IN SO_BELNR.
DELETE <LT_DATA>.
ENDIF.
UNASSIGN <L_FIELD>.
ENDLOOP.
and here is the description of my dump:->>>
You attempted to access an unassigned field symbol
(data segment 32772).
This error may occur for any of the following reasons:
- You address a typed field symbol before it is set using ASSIGN
- You address a field symbol that points to a line in an internal table
that has been deleted
- You address a field symbol that had previously been reset using
UNASSIGN, or that pointed to a local field that no longer exists
- You address a global function interface parameter, even
though the relevant function module is not active,
that is it is not in the list of active calls. You can get the list
of active calls from the this short dump.

Dynamic sql reurns no data when multiple values are passed.

(Dynamic sql returns no data when multiple values are passed.)
Hi,
While executing the below dynamic sql in the procedure no data is returned when it has multiple input values.
When the input is EMPID := '1'; the procedure works fine and returns data.Any suggestion why the procedure doen't works when input as EMPID := '1'',''2'; is passed as parameter?
=======================================================
create or replace PROCEDURE TEST(EMPID IN VARCHAR2, rc OUT sys_refcursor)
IS
stmt VARCHAR2(9272);
V_EMPID VARCHAR2(100);
BEGIN
V_EMPID :=EMPID;
stmt := 'select * from TEST123 where Empid is NOT NULL';
IF V_EMPID <> '-1' THEN
stmt := stmt || ' and Empid in (:1)';
ELSE
stmt := stmt || ' and -1 = :1';
END IF;
OPEN rc FOR stmt USING V_EMPID;
END Z_TEST;
============================================================
Script for create table
==================================================================
CREATE TABLE TEST123 (
EMPID VARCHAR2(10 BYTE),
DEPT NUMBER(3,0)
===========================================
Insert into PDEVUSER.TEST123 (EMPID,DEPT) values ('1',20);
Insert into PDEVUSER.TEST123 (EMPID,DEPT) values ('2',10);
Insert into PDEVUSER.TEST123 (EMPID,DEPT) values ('3',30);
Insert into PDEVUSER.TEST123 (EMPID,DEPT) values ('3',30);
Insert into PDEVUSER.TEST123 (EMPID,DEPT) values ('2',10);
=============================================
Select * from TEST123 where Empid in (1,2,3)
EMPID DEPT
1     20
2     10
3     30
3     30
2     10
===================================================================
Any suggestion why the procedure doen't works when input EMPID := '1'',''2';?
Thank you,

The whole scenario is a little strange. When I tried to compile your procedure it couldn't compile, but I added the missing info and was able to get it compiled.
create or replace PROCEDURE TEST (EMPID IN VARCHAR2, rc OUT sys_refcursor)
IS
stmt        VARCHAR2 (9272);
V_EMPID     VARCHAR2 (100);
BEGIN
V_EMPID := EMPID;
stmt := 'select * from TEST123 where Empid is NOT NULL';
IF V_EMPID = '-1' THEN
    stmt := stmt || ' and Empid in (:1)';
ELSE
    stmt := stmt || ' and -1 = :1';
END IF;
OPEN rc FOR stmt USING V_EMPID;
END;If you pass in 1 as a parameter, it is going to execute because the statement that it is building is:
select * from TEST123 where Empid is NOT NULL and -1 = 1Although the syntax is valid -1 will never equal 1 so you will never get any data.
If you pass in 1,2 as a parameter then it is basically building the following:
select * from TEST123 where Empid is NOT NULL and -1 = 1,2This will cause an invalid number because it is trying to check where -1 = 1,2
You could always change your code to:
PROCEDURE TEST (EMPID IN VARCHAR2, rc OUT sys_refcursor)
IS
stmt        VARCHAR2 (9272);
V_EMPID     VARCHAR2 (100);
BEGIN
V_EMPID := EMPID;
stmt := 'select * from TEST123 where Empid is NOT NULL';
stmt := stmt || ' and Empid in (:1)';
OPEN rc FOR stmt USING V_EMPID;
END;and forget the if v_empid = '-1' check. If you pass in a 1 it will work, if you pass in 1,2 is will work, but don't pass them in with any tick marks.

SAP MII 14.0 SP5 Patch 11 - Error has occurred while processing data stream Dynamic Query role is not assigned to the Data Server

Hello All,
We are using a two tier architecture.
Our Corp server calls the refinery server.
Our CORP MII server uses user id abc_user to connect to the refinery data server.
The user id abc_user has the SAP_xMII_Dynamic_Query role.
The data server also has the checkbox for allow dynamic query enabled.
But we are still getting the following error
Error has occurred while processing data stream
Dynamic Query role is not assigned to the Data Server; Use query template
Once we add the SAP_xMII_Dynamic_Query role to the data server everything works fine. Is this feature by design ?
Thanks,
Kiran

Thanks Anushree !!
I thought that just adding the role to the user and enabling the dynamic query checkbox on the data server should work.
But we even needed to add the role to the data server.
Thanks,
Kiran

Date Based Dynamic Member Calculation Performance (MTD, YTD, PeriodsToDate)

I'm working on an SSAS 2012 cube and I have defined several dynamic calculations based on a Date (MTD, YTD, TD, Thru Previous Month, etc.).
The cube has a well defined Date dimension and I have set up a DYNAMIC calculated set in the cube as shown below.
CREATE DYNAMIC SET CURRENTCUBE.[Latest Date]
AS TAIL(EXISTS([Payment Date].[Calendar Date].[Date].Members,[Payment Date].[Calendar Date].CURRENTMEMBER,"Claim Payment"));
... and here is an example of one of my calculations.
CREATE MEMBER CURRENTCUBE.[Measures].[Face Amount Paid MTD]
AS SUM(MTD([Latest Date].ITEM(0).ITEM(0)), [Measures].[Face Amount Paid]),
FORMAT_STRING = "$#,##0.00;-$#,##0.00",
//NON_EMPTY_BEHAVIOR = { [Claim Payment Fact Count] },
VISIBLE = 1 , DISPLAY_FOLDER = 'Face Amount' , ASSOCIATED_MEASURE_GROUP = 'Claim Payment';
This calculation returns the correct results, but performs horribly. I've noticed that changing the [Latest Date] set to STATIC, performance greatly improves, but numbers are no longer accurate as they are based on the Tail of the Claim Payment measure
group without considering the filtered dates. This is because the date is evaluated at process time, but needs to be based on users date selection to be accurate. Therefore, STATIC does not appear to be an option. Is there a better way to
perform this calculation dynamically based on the filtered or unfiltered date dimension?

Typically I would just do YTD/MTD/etc off the date the user has selected. It seems like you want to do it based on the last date with data within the range they have selected. Why not just give the user what they are asking for?
In other words, why not
YTD([Payment Date].[Calendar Date].currentmember)

Creation of internal table dynamically based on the Date Range entered

Hi SAPgurus,
I have been facing one issue i.e creation of internal table dynamically based on the date range entered in the selection screen. For example the date range I am giving as 06/2006 to 08/2006, it should display the Fieldcatelog dynamically, this part i have completed but the only issue I am facing is to populate the sales data into that fields.
Right now my program is displaying the ALV like this.
Ex:
<b>CSR    District   06/2006 07/2006 08/2006 totals</b>
Shiva      New York                             10.00
Shiva      new york                             30.00
Shiva      new york                             40.00
but it should display like this
<b>CSR    District 06/2006 07/2006 08/2006 totals</b>
Shiva New York 10.00   30.00 40.00
80.00
Please help me in this scenario, how to acheive like this..
Thanks & Regards,
Sivaram Kandula

Hi Sivaram,
             I also got the same requirement . i saw rich and your code whatever you have uploaded.i have created dynamic internal table but i am facing the issue to populating the data to my dynamic internal table.
Sivaram, can you please explain your code after this.
*<dyn_table>
*tab_item.
LOOP AT tab_item.
    ASSIGN COMPONENT 1 OF STRUCTURE <dyn_wa> TO <dyn_table>.
    ASSIGN COMPONENT 2 OF STRUCTURE <dyn_wa> TO <dyn_table>.
*    <dyn_wa> = tab_item-bztxt.
*    <dyn_wa> = tab_item-total.
*    APPEND <dyn_wa> TO <dyn_table>.
**    <dyn_wa> = tab_item-total.
**    ASSIGN tab_item-bezei TO <dyn_wa>.
* APPEND <dyn_table>.
ENDLOOP.
how you are puting the loop at tab_item. but tab_item is already commented.
can you send me the code after that.
i am sending some part of my code.
CALL METHOD cl_alv_table_create=>create_dynamic_table
   EXPORTING
     it_fieldcatalog = gt_fCAT1
   IMPORTING
     ep_table        = new_table.
ASSIGN new_table->* TO <dyn_table>.
   create data new_line like line of <dyn_table>.
   assign new_line->* to <dyn_wa>.
select vbeln
        fkart
        vkorg
        vtweg
        fkdat
        spart
        fksto
        from vbrk
        client specified
        into table gt_vbrk
        where mandt = sy-mandt
        and fkart in ('ZF5','ZFR')
        and vkorg = '1100'
        and vtweg = '20'
        and fkdat in s_fkdat
        and spart = '06'
        and fksto = ' '.
   if gt_vbrk[] is not initial.
select vbeln
          fkimg
          prsdt
          netwr
          matnr
          arktx
          werks
          mwsbp
          from vbrp
          client specified
          into table gt_vbrp
          for all entries in gt_vbrk
          where vbeln = gt_vbrk-vbeln
          and werks in s_werks
          and matnr in s_matnr.
endif.
select mnr ltx spras from t247
into table it_t247
where spras = 'E'.
data: lv_month1 type vbrp-prsdt,
       name1(3) type c,
       s_month type string,
        s_month1 type string,
         s_month2 type string.
*      lv_netwr1 type vbrp-netwr,
*          lv_mwsbp1 type vbrp-mwsbp.
      loop at gt_vbrp into gs_vbrp.
        gs_final2-matnr = gs_vbrp-matnr.
        gs_final2-arktx = gs_vbrp-arktx.
        gs_final2-fkimg = gs_vbrp-fkimg.
       lv_month1 = gs_vbrp-prsdt.
        read table it_t247 into wa_t247 with key mnr = lv_month1+4(2).
        if sy-subrc eq 0.
        name1 = wa_t247-ltx.
        endif.
         concatenate name1
                   lv_month1(4) into s_month SEPARATED BY '_' .
         CONCATENATE S_MONTH 'QTY' INTO S_MONTH1 SEPARATED BY ''.
          CONCATENATE S_MONTH 'VALUE' INTO S_MONTH2 SEPARATED BY ''.
         gs_final2-month = s_month.
          lv_netwr1 = gs_vbrp-netwr.
        lv_mwsbp1 = gs_vbrp-mwsbp.
        gs_final2-MONTH_QTY = S_MONTH1.
        GS_FINAL2-MONTH_VAL = S_MONTH2.
        gs_final2-value = lv_netwr1 + lv_mwsbp1.
       append gs_final2 to gt_final2.
       clear: gs_final2. "lv_name2.
       endloop.
       if gt_final2[] is not initial.
         sort gt_final2 by matnr month ascending .
         loop at gt_final2 into gs_final2.
        gs_final2_01 = gs_final2.
     collect gs_final2_01 into gt_final2_01.
    endloop.
       endif.
   ENDIF..
Regards
Ankur

Convert "1D array of dynamic data" to "Dynamic data" after auto-indexing with loop

Similar Messages

Maybe you are looking for