Create Material directly in active area without approval process ( Bypasing Staging)

Hi Experts ,
I have one requirement where Material need to be created directly in active area with out any approval process.
So I need to bypass staging area data store.
Please give your valuable input to achieve that.
Thanks in advance.
Regards,
Samrat

Hello,
From the discussion above, I can understand this is a requirement. However, I would like to understand the reasoning behind this requirement. The whole point behind MDG is to avoid direct creation of master data and instead "govern" the process first. If you are going to create material, then use MM01 directly as Sanjay suggested.
If you are looking for a web-based UI, you are better off looking for a standard Web Dynpro application (or create your own) instead of mis-using the MDG application.
In any case, you can't completely by-pass the staging area. However, you can configure a single-step rule-based workflow such that the material goes into "activation" immediately. Keep in mind that the material will not be available immediately, but will take a few minutes depending on your system configuration until the material is activated completely in the system. Error handling, etc. will need to be done on the MDG layer which could prove to be an unnecessary burden should you decide to go this route.

Similar Messages

Re: create material cost estimate with ck11n without

hi gurus,
i need to do create material cost estimate with ck11n without cost result but before i need to check the BOM with material component 11111, and also instruct me how to correct maintain BOM list to get the standard cost
if anybody do the same scenoria giveme your golden inputs
thanks in advance,
kumar.b

Hi,
As note 351835 explains, calculation needs an inforecord to calculate prices from purchasing. Prices from outline agreements are generally not taken into account. According to note 499699, the system may consider entries in the source but it will ignore entered agreements (before this correction, any source list entries with agreement were ignored).
Prices from agreements could only be considered either via a modification or by using the user exit for material valuation (COPCP005).
This unfortuntely is a restriction resulting as a side-effect from note 499699. As soon as an agreement is entered in the source list, the fixed indicator will not be considered anymore.
You therefore have two options to overcome this.
1) You create a second source list entry without an agreement; then the fix indicator will be reflected; report Z_CREATE_EORD from note 409960 could be used to do this automatically
2) You are using user-exit EXIT_SAPLMEQR_001 in order to 'overrule' the standard search for source of supply (enhancement LMEQR001)
regards
Waman

Form of active area

I need create button - pointer with active area (with triangle form) to next menu-screen! So, now active area have rectangle form.
How I can do it (pointer with active area with triangle form)?

You can create a Button, with a triangular graphic on it, BUT the active area of that Button will be a rectangle, that encompasses all of the elements of that Button. There is no way to change the shape from a rectangle, but the user will not see that rectangle. All they will see will be the grahics and the Sub-picture Highlight, if one is created. That Sub-picture Highlight can take on almost any Shape, from a triangle to a multi-sided polygon, but that will be inside the rectangle, that defines the Button and all of its elements. Note: with multiple Buttons, there can be NO overlap of those rectangles. They must be separate and must never overlap.
Hope that helps, and good luck,
Hunt

OIM 11g Approval Process

Hi Expert/All,
May I have assistance regarding the OIM 11g?
Currently, I already create one approval (only 1 level approval) for some resource in OIM 11g, then I'm continue to test the resource with two below way:
1. If I'm try to add "New Resource" directly by xelsysadm via manage user menu (without approval process), the provisioning process was successfully creating new account in the target system.
2. The wierd is if I'm try to test Self-service request by user, after approval by last level approval, then there is no provisioning activity by OIM system, it is like OIM do nothing. The request status is show "Obtaining Template Approval" and history approval is complete by manager user (only 1 level approval)
My question is, does it still required any configuration for completing the provisioning process after the approval process?
Thanks,
Ricky R

Hi Kevin,
Thanks for the information, but it still do nothing, OIM did not continue the provisioning account to target system event I already assign SYSTEM ADMINISTRATOR roles to the user and manager. How I can trace this logs? currently I'm just look at the oim_server1.log at <OIM_DOMAIN>/severs/oim_server1/logs. Is there any other log file can we use to trace the app server logs?
Thanks,
Ricky R

OIM 11g Self-registration approval process

Hi
I wanted an OIM self-Registration request to be auto-approved. I am using OIM11g.
Can anyone give me the directions.
Regards
user12841694

The OIM11g approval process are three levels.
1. template level
2. request level
3. operational level
Both template level and operational level can be auto approved where as the request level cannot be.
The reason being, the self-regisistration template ships with user's organization attribue as the Approver-Only attribute indicating it should be populated only by the apporver.
Looking for any possible options to auto approve request level also.
http://download.oracle.com/docs/cd/E14571_01/doc.1111/e14316/unauth_selfservice.htm#OMUSG3065
Regards
user12841694
Edited by: user12841694 on Nov 9, 2010 10:20 PM

Material created from Nwbc, after activation it is visible in ECC mm03, but cannot be viewed in nwbc display material

Dear Freinds,
We are creating a Material from Nwbc, after activation and workflow approval it is visible in ECC mm03, But cannot be viewed in nwbc display material.
There is some configuration mistake or technical issue?
Regards
Sukumar

Dear Sukumar,
MDG Material search is based on Enterprise search. Pls check if the ES at MDG system is configured correctly and is working fine with all connectors in "active" status.
Regards, JVR

How to create a view for all Service Requests that are not approved by reviewer

Hallo,
I want to create a view in the Service Requests library that shows all SRs that are not approved. How to configure condition that says: if a SR has related Review Activity which is In Progress, show that SRs?
I couldn't find this when creating the view. Thank you.

So here's the first problem with that: Which review activity? a SR can contain multiple RAs, so how do we decide if an arbitrary SR is approved or not?
As to the specific language you use (Any child RA is In Progress) you might want to look at the criteria from the default Change approval view, which does something similar:
<QueryCriteria Adapter="omsdk://Adapters/Criteria" xmlns="http://tempuri.org/Criteria.xsd">
<Criteria>
<FreeformCriteria>
<Freeform>
<Criteria xmlns="http://Microsoft.EnterpriseManagement.Core.Criteria/">
<Expression>
<And>
<Expression>
<SimpleExpression>
<ValueExpressionLeft>
<Property>$Context/Path[Relationship='CoreActivity!System.WorkItemContainsActivity' TypeConstraint='CoreActivity!System.WorkItem.Activity.ReviewActivity']/Property[Type='CoreActivity!System.WorkItem.Activity']/Status$</Property>
</ValueExpressionLeft>
<Operator>Equal</Operator>
<ValueExpressionRight>
<Value>$MPElement[Name="CoreActivity!ActivityStatusEnum.Active"]$</Value>
</ValueExpressionRight>
</SimpleExpression>
</Expression>
<Expression>
<SimpleExpression>
<ValueExpressionLeft>
<Property>$Context/Property[Type='CoreChange!System.WorkItem.ChangeRequest']/Status$</Property>
</ValueExpressionLeft>
<Operator>Equal</Operator>
<ValueExpressionRight>
<Value>$MPElement[Name="CoreChange!ChangeStatusEnum.InProgress"]$</Value>
</ValueExpressionRight>
</SimpleExpression>
</Expression>
</And>
</Expression>
</Criteria>
</Freeform>
</FreeformCriteria>
</Criteria>
</QueryCriteria>
This is a simple AND criteria with two componets. one looking for a Review Activity (TypeConstraint='CoreActivity!System.WorkItem.Activity.ReviewActivity') which is related to the targetting CR by Contains Activity ($Context/Path[Relationship='CoreActivity!System.WorkItemContainsActivity';
Context in this... context means the CR targeted by the view) where it's status (/Property[Type='CoreActivity!System.WorkItem.Activity']/Status$) is In Progress ($MPElement[Name="CoreActivity!ActivityStatusEnum.Active"]$). The other is filtering
for the target change request's status ( $Context/Property[Type='CoreChange!System.WorkItem.ChangeRequest']/Status$) is In Progress ($MPElement[Name="CoreChange!ChangeStatusEnum.InProgress"]$).
You could convert the second criteria to point to SRs and SR status values, and then use the similar text for the first criteria. i'd recommend
Anton's Advanced View Editor (or
the free version) to do the criteria adjustment.

Is it possible to Create Material Master without Profit Center ?

Hai,
      1) Is it possible to Create Material Master without Profit Center ?
      2) How SAP System Validate Profit Center in material master. ? is it material Type wise ?
      3) Whether PO Order Creation,GRN & MIRO Possible for those material Master without Profit Center.?
Kindly Explain me clearly..
Thanks & Regards,
Swetha

Hi,
Profit center is at the plant level.
You can create material master even with out a profit center.This field will be there in the costing view and and general sales/plant data.
while creation of the materila master if do not select these views system will not ask for that.Normally it is pertaining to the costing analysis.
A profit center manager is held accountable for both revenues, and costs (expenses), and therefore, profits. What this means in terms of managerial responsibilities is that the manager has to drive the sales revenue generating activities which leads to cash inflows and at the same time control the cost (cash outflows) causing activities. This makes the profit center management more challenging than cost centre management. Profit center management is equivalent to running an independent business because a profit center business unit or department is treated as a distinct entity enabling revenues and expenses to be determined and its profitability to be measured.
Business organizations may be organized in terms of profit centers where the profit center's revenues and expenses are held separate from the main company's in order to determine their profitability. Usually different profit centers are separated for accounting purposes so that the management can follow how much profit each center makes and compare their relative efficiency and profit. Examples of typical profit centers are a store, a sales organization and a consulting organization whose profitability can be measured.
For more info,please refer
http://help.sap.com/erp2005_ehp_04/helpdata/EN/cc/36428094f311d2b47a006094b9b0a5/frameset.htm,
Regards,

How to create a PO for a Material having Net Price but without Info Record?

Hi,
When I try to create a PO for a Material having Material Master and Vendor Master maintained but no Info Record, system does not accept the Net Price and the Price Condition also does not appear. Is there any way to create a PO for a Material having Net Price but without Info Record?
Regards.

Hi,
The first time you create a PO for a material/vendor combination, then system will not prompt any price as info record or valid conditions have not been found.
The next time you create a PO for the same material, then the price will be defaulted/found from the order price history from the info record(As info record would be reated after the first PO is created) and the latest PO price for the mat/ven combination would be found.
Hope you are clear with this..Any doubts revert back.
Regards,
Deepak.

To receive material directly into warehouse with out creating TO

Hi all,
Iam having a requirement in warehouse- I want to recive the material directly in to warehouse against a PO with out creating any Transfer order.
I want to know what are all the setups we need to maintain.
Thanks in advance
Venkatesh.

Dear Venkatesh
please understand the client requirement ,
if you want to receipt the good against PO, material post in to inventory management then to warehouse management ,
try this in order to create Automatic TO & Confirm the same
Implementation Guide for R/3 Customizing (IMG)>Logistics Execution>Warehouse Management>Activities>Define Movement Types
in movement type 101 please check the setting under background processing & confirmation for automatic TO creation as well as The transfer order item may be confirmed immediately

HowTo create a direct link to an approval

Hi all,
did someone of you tried to create a direct link to an approval?
The link looks like this: "u2026/ProcessRequest?RequestID=12345&TaskID=111&EntryID=01234"
So my question:
Is it possible to use SQL statements in these scripts to read out the needed data from "MXP_PROVISION"?
I have tried out this:
Configuration in "EMailNotifiaction_Approval" Pass:
MSKEY     %MSKEY%
MX_APPROVERS    %MX_APPROVERS%
MX_ENTRY_REFERENCE     %MX_ENTRY_REFERENCE%
Coding in the script of "Next data entry" (just the relevant part)
var entryReference = Par.get ("MX_ENTRY_REFERENCE");
var sql = "SELECT MSKEY FROM MXP_PROVISION WHERE AUDITREF = " + entryReference;
var sqlresult = "";
sqlresult = uSelect (sql);
I don´t get a Value into "sqlresult". I think one problem is that he doesn´t read the value of entryReference
Br,
Philip

Thank you Thomas,
the privilege was the problem.
Maybe someone of you had the same problem.
I have solved it like this now: (All with * marked lines can be found in the HowTo guide)
*var pendingValue = Par.get("MSKEY");
*var approverList = Par.get("MX_APPROVERS");
*var entryReference = Par.get("MX_ENTRY_REFERENCE");
*// uErrMsg(logLevel,"Approver List: " + approverList);
*var approvers = new java.util.Vector();
*approvers = uSplitString (approverList, "|");
*var i = 0;
*var result;
*var emailAddress = "";
*var idStore = uGetIDStore();
*var emailAttribute = "%$MAILATTRIBUTE%";
var sql = "SELECT APPROVALTASKID, AUDITREF, PARENTMSKEY FROM MXWV_PENDING_APPROVALS WHERE MSKEY = " + pendingValue;
var sqlresult = "" ;
sqlresult = uSelect(sql);
var part = new java.util.Vector();
part = uSplitString (sqlresult, "|");
actionid = part.get(0);
auditref = part.get(1);
usermskey = part.get(2);
// This line was made to get the unique name of the requesting person
var sqlname = "SELECT AVALUE FROM MXIV_SENTRIES WHERE (ATTR_ID = 2 AND MSKEY = " + usermskey + ")";
var name = "";
name = uSelect(sqlname);
var url = "http://10.44.110.68:50000/webdynpro/dispatcher/sap.com/tcidmwd~workflow/ProcessRequest?RequestID=" + auditref + "&TaskID=" + actionid + "&EntryID=" + pendingValue;
I think there are much more solution. (Iam new at IdM )
Br,
Philip

How to create folder and items in content area without edit folder option

Hello!!
I would like to create something to users can create and insert folders and items in content area without using the edit folder option.They would have a form to include the name of the file and the name.i would like to do this for the end users can insert files more easily. Can i do this? Anyone can help me ??
Thanks in advance!!!
null

The wwsbr_api and wwsbr_search_api packages are included in the current PDK, but won't be supported until 3.0.8 is release, later this month.
Regards,
Jerry
null

OIM11gR2 - Is it possible to create a direct link to a specific area in the oim plattform?

hi,
is it possible to create a direct link to specific area in the oim self service plattform? for example a link to the users account list, or a link to a specific resource account?
br,
max

Hi,
Yes, Its very much easy in R2 as compared to R1. You can use following link to achieve your requirement:
http://docs.oracle.com/cd/E27559_01/dev.1112/e27150/uicust.htm#BABIDJAB
~J

Create Materialized View ORA-01723: zero-length columns are not allowed

I am trying to create a materialized view which derives a column from a function and I get: ORA-01723: zero-length columns are not allowed.
I am using 10gR2 with the following definition (simple version):
CREATE MATERIALIZED VIEW AS
SELECT
function_name(column_name) COLUMN_ALIAS
FROM table_name;
I have even tried to cast it like below:
CREATE MATERIALIZED VIEW AS
SELECT
CAST(function_name(column_name) AS VARCHAR2(200)) COLUMN_ALIAS
FROM table_name;
My function does have an exception to return a value even if no values are found.
I have looked all over for the solution. Does anyone have a way around this issue? I really need my function to derive the column as it has business rules which I cannot join into my materialized view definition. My only hope around this is to insert the values into a table and then create a materialized view from that table, I don't want to do that if someone has a solution around this.
Any help would be greatly appreciated.
Thank you,
Kyle
Edited by: Kyle Miller on Apr 19, 2011 8:28 AM

Have you tried creating a table with the correct structure and then creating the materialized view based on the prebuilt table as described here...
http://www.oaktable.net/content/ultra-fast-mv-alteration-using-prebuilt-table-option
Cheers
Ben

ISR For Approve Create Material Master

I have requirement apply ISR for Control Create Master.Example User1 input information about purchasing group and send to User2. And then User2 input information about Plant and send to next user for approve.If already send to last user and submit,ISR will be create material master.
But i don't know could be apply ISR for this case, Because i find for Costing and Banking.
Please help me. Thank you very much

Hi,
You need to speak to a workflow consultant.
You can get workflow to do many things (including creating a material master) but it takes a lot of coding and design.
For those of you who think that workflow is just used for the standard SAP workflow tasks, you have to realise that workflow is far more powerful and far more useful than many people think.
It is always referred to as "Event triggered messaging" but it is more accurate to call it "Event triggered events".
Within workflow you can chain together many different transactions and or ABAPS and so you can get it to do virtually anything you want (as long as you know how).
In this case you need the workflow to trigger an ABAP or BTCI session etc. that works through the MM01 transaction. It is relatively easy to get it to do this, but I am not technical enough to be able to help with the steps involved (sorry)
Steve B

Create Material directly in active area without approval process ( Bypasing Staging)

Similar Messages

Maybe you are looking for