CSM server originated connections
Hi,
I have a CSM running in router mode with one client vlan, one server vlan and two server vlans for SCAs. Load Balancing is ok, connections directly to the servers and the SCAs through the CSM are ok.
Connections from the server vlan directed to the outside via next hop into the client vlan
(the opposite direction of the usual access) don't work.
Scenario: Server - CSM - MSFC
The client VLAN has the MSFC vlan interface configured as its gateway, the cisco docu says,
that server originated connections should work by default without any NAT, but they don't here.
I also tried "static nat <ip>" and "static nat virtual", no success. The outside vlan interface of the CSM is the last point I can ping, the MSFC doesn't respond, though it is the gateway
address.
Funny: I can ping the SCAs in their vlans and the SCAs can ping the gateway on the MSFC,
it's only from the servers into the client vlan that has trouble...
Does anyone have an idea what's wrong?
Thanks for every hint
Uli
It works for me.
Do a 'sho mod csm X conn' and look for the entry created for the ping from the server to the msfc.
Make sure the response from the msfc matches the entry - same vlan !!!
Check the route from msfc to server and make sure it goes to the same vlan as traffic from server to msfc.
Also, if you did some modification in the vlans or static routes, clear the csm connections since icmp creates long lived entry.
Regards,
Gilles.
Similar Messages
-
CSM: server-initiated connections
Hello
I hope you can help me to figure out this question, I have a CSM module with more than 10 serverfarms, all of them working fine, and all of them are on different vlans. We are using route mode for all of them.
For example:
ServerFarm01-> Vlan10
Client_Side01-> Vlan11
ServerFarm02-> Vlan20
Client_Side02-> Vlan21
ServerFarm03-> Vlan30
Client_Side03-> Vlan31
and so on...
I noticed something, When I generate outbound traffic from a real server, it does not matter it belong to SeverFarm01, 02 or 03; the packet leaves the CSM using alway the vlan31.
Can you please help to determine what’s going on?
Actually, we want realservers from ServerFarm01 to sent traffic to internet through the CSM, and those traffic should be seen on vlan11.
Thankds and Regards
EdgarHi Edgar,
Few things to check.
Check if the servers has two interface. It may be sending traffic through other interface.
Please go through below configuration guidelines that will help you to associate Particular serverfarm with their respective VLAN.
Configuring Server-Initiated Connections
The NAT for the server allows you to support connections initiated by real servers and to provide a default configuration used for servers initiating connections that do not have matching entries in the server NAT configuration. By default, the CSM allows server-originated connections without NAT.
To configure NAT for the server, perform this task:
Command
Purpose
Step 1
Router(config)# static [drop | nat
[ip-address | virtual]]
Configures the server-originated connections. Options include dropping the connections, configuring them with NAT with a given IP address, or with the virtual IP address that they are associated with1 , 2 .
Step 2
Router(config-slb-static)# real ip-address
[subnet-mask]
Configures the static NAT submode where the servers will have this NAT option. You cannot use the same real server with multiple NAT configuration options.
1 Enter the exit command to leave a mode or submode. Enter the end command to return to the menu's top level.
2 The no form of this command restores the defaults.
For Example :
static nat 199.200.9.140 ( IP can be virtual IP as well)
real 192.168.24.0 255.255.252.0
real 192.168.20.0 255.255.252.0 -
CSM in Bridge mode and Server initiated connections
I know one can use Source NAT for server initiated connections back to VIP using CSM in routed mode. How do I achieve the same for bridge mode?
Thanks in advance,
ShahidShahid,
that's a well-known problem for all loadbalancer in the world.
With a sniffer trace, or just thinking about TCP/IP rules you can figure out why client nat is required.
If you go from a server to a vip, the CSM will forward the traffic to a random server.
The CSM forwards the traffic with the source ip unchanged by default.
The server receiving the traffic will forward the response back to the source that initiated the request.
If the source is also a server in the same subnet, the response does not need to be sent through a gateway. Since both source and destination are in the same subnet, the traffic is sent based on mac address and it bypasses the CSM which can't perform the nating.
The source receiving the response from the server directly will just ignore it.
Using client nat forces the response to go back to the CSM which can perform the nating before sending it to the client.
This has been discussed tons of times in this forum.
It's a classic question :-)
Gilles. -
Every few days we see two dialogs with the following messages:
Dialog 1, title: Check for Licensing Compliance is Incomplete
The server did not finish checking the license compliance. If the server is joined to a domain, make sure that the server can connect to a domain controller.
Dialog 2, title: Check for Licensing Compliance is Incomplete
The server did not finish checking the license compliance. If the server is joined to a domain, make sure that the server can connect to a domain controller. If the license compliance check cannot be completed, the server will automatically shut
down in 8 day(s) 23 hour(s) 0 minute(s).
The server is not (and never has been) joined to a domain or had any DC roles installed. In fact its still connected to the default Workgroup.
The server was configured in our office and never showed this message until it was installed on site. The main difference from what I can see is that when installed on site it was given a static IP address and does not have any DNS settings in the network
adapter properties.
I have scoured a number of forums on this error but in almost every other instance of this error message the servers are connected to a Domain Controller and the solutions generally are linked to dis-joining and rejoining the domain. Unfortunately this is
not an option for this scenario.
I initially thought that adding some relevant DNS server IP address may resolve the issue, however, we have the exact same model server configured exactly the same running at a different site that does not experience this problem. This server also has no
DNS server configured.
I have seen a post that suggests turning off the servers "Foundation Checking", but I'm unsure how to do this.Thanks for your response Vivian.
I can confirm that this server is not (and never has been) a member of any active directory, it is configured as a Workgroup server. It was initially configured on a network that does have an active directory, but was never joined to it. During that time it
never displayed these messages.
The server was moved into production on a different site and network and setup with a static IP address.The site network does have its own active directory but the server was not joined to it. It is whilst on this new network that these messages began.
Since my original post DNS servers have been added and the Microsoft activation has been verified, however, the messages are still appearing.
There are only 2 user accounts configured on this server. The local admin account and another local admin user.
The remote desktop services roles have been installed but not yet configured. I don't think that has any bearing on this scenario though.
The description of this error in the above "Introduction to Windows Server 2012 Foundation" link states:
This error occurs when the server cannot finish checking the requirements for the root domain, forest trust configuration, or both. It usually happens when the server cannot connect to a domain controller. If the situation persists, the server will
shut down 10 days after the first time the compliance check failed. Each time this error message occurs, it will state the actual time remaining before the server will shut down. If you restart the server after it has shut down because of non-compliance, the
server will shut itself down again in 3 days.
The above description leads me to the following question - In a Workgroup environment, does the server still try to contact a domain controller to establish a level of trust? If this is the case could it be that the server can no longer see the initial DC
on its new network and this is what is triggering the messages?
Am I clutching at straws here? -
The error also has "to repair the configuration, follow steps for repairing dpm from DPM setup help ID: 3001
I tried the solution outlined here:
http://social.technet.microsoft.com/Forums/en-US/8be919ee-f358-47a4-9cc3-d23eb05d3f18/system-center-2012-r2-dpm-smtp-issue-reporting-services-server-cannot-connect-to-the-dpm?forum=dataprotectionmanager
and also the graphical depiction here: http://www.ms4u.info/2014/01/reporting-services-server-cannot.html
I tried these steps, but everytime i try to change it, it tells me:
"The permissions granted to user 'domain\userid' are insufficient for performing this action rsaccessdenied..
Nothing seems to work..
I thought if i went into sql management studio and made sure my userid had admin rights to the db it would work.. but i cant change it there (via integrated security).. i believe i need to login as SA, but i dont recall the password for SA, though it appears
i can change the SA password from within sql management studio.. i'm unsure if doing so will break DPM though or is even needed to fix the reporting integration issue..
Any thoughts on this?
Thanks
Tech, the Universe, Everything: http://tech-stew.comUsing:
data source="servername\MSDPM2012";persist security info=False;initial catalog=DPMDB
I used the domain sqlservice account and test connection was ok.
However.. accessing reports still crashes in the MMC
Tech, the Universe, Everything: http://tech-stew.com
When i recreated the db.. i called it Reporting2 or similiar..
Then the reports folder i created called "Reports Folder"
Then datasource name "reports datasource"
The issue here is that the DPM reports in the reporting web interface are gone, since this is a new DB.. how do i redeploy them
Tech, the Universe, Everything: http://tech-stew.com
i went back into the sql reporting services area.. hit change db.. chose the original .. then back to the url.. went to the OLD reporting services folder and datasource.. added the connect string and now reporting area works.. so does scheduling..
Problem now solved
Tech, the Universe, Everything: http://tech-stew.com
Oops spoke too soon.. the first time i set it to do "status" as a schedule.. it seemed to work (clicked ok, no error).. went back and added an email notification..
Now i'm getting.. "an error occurred causing the reporting job to fail" "system files may be corrupt".
Seems to only occur if i try to add the email address portion
Tech, the Universe, Everything: http://tech-stew.com
rechecked the datasource.. i think there was an error in the connect string.. now everything seems to be working.. email notifications and all.
Tech, the Universe, Everything: http://tech-stew.com -
CSM Server LB across L3 Devices
I have a pair of 6513's with a CSM in each. These are port-channelled together to provide FT.
I have a number of server vlan's defined on the 6500 and 2 of these need to be LB through the CSM.
Do I define these servers as CSM server vlans (which I have now done) or define the servers as 6500 server vlans with L3 interfaces defined on the 6500's and add route commands to the CSM server VLAN's to route back to these servers via the 6500 L3. I am concerned on this last point about Nat requirements for client connections and how to guage the number of nat pool addresses I need.
My reason for this question is that I am having trouble getting ping access to these LB servers through the CSM even though I have defined server farms with a predictor of forward. Cisco give information on forwarding using TCP / UDP but give no indication of whether the CSM predictor forward supports ICMP.I am having trouble pinging from an interface on the sup720 / switch fabric on a different subnet to a server on a vlan defined in the CSM as a server vlan.
Not seeing any hits on the csm for this serverfarm.
You said the servers can be on either the CSM or MSFC, but if put the servers to be load balanced on the MSFC, I will need to put in client Nat on the serverfarm to ensure the real server does not attempt to reply directly back to the requestee. If this is the case, does the CSS use a 1 to 1 Nat relationship or does it essentially do a many to 1 address (PAT) -
I would like to know which apple server dictation connects to so that my proxy server will stop blocking it. Which apple server does it connect too?
I would presume so, but it might be worth your while to experiment and play around with different combinations to see if you can block FaceTime while keeping Game Center open. Good luck!
-
i need a help. I am new in company and have to solve this problem.
My colleague did a migration from Small Business server 2003 to Foundation 2008, about 1 year ago. After few days, he got this error message in title. Server turn off about once a month. He worked following:
joined new server Foundation to the Domain
dcpromo on new Server
migration (he said that he worked step-by-step with tutorial)
demote on old Server SBS 2003
disconnect old server from domain. This old is not in function now.
New server have just 3 computer accounts. The Forest functional level is Server 2003.
I've did dcdiag:
C:\Users\Administrator>slmgr.vbs /dli
C:\Users\Administrator>dcdiag
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
Home Server = server2008
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site-Name\SERVER2008
Starting test: Connectivity
......................... SERVER2008 passed test Connectivity
Doing primary tests
Testing server: Default-First-Site-Name\SERVER2008
Starting test: Advertising
......................... SERVER2008 passed test Advertising
Starting test: FrsEvent
......................... SERVER2008 passed test FrsEvent
Starting test: DFSREvent
......................... SERVER2008 passed test DFSREvent
Starting test: SysVolCheck
......................... SERVER2008 passed test SysVolCheck
Starting test: KccEvent
......................... SERVER2008 passed test KccEvent
Starting test: KnowsOfRoleHolders
......................... SERVER2008 passed test KnowsOfRoleHolders
Starting test: MachineAccount
......................... SERVER2008 passed test MachineAccount
Starting test: NCSecDesc
......................... SERVER2008 passed test NCSecDesc
Starting test: NetLogons
......................... SERVER2008 passed test NetLogons
Starting test: ObjectsReplicated
......................... SERVER2008 passed test ObjectsReplicated
Starting test: Replications
......................... SERVER2008 passed test Replications
Starting test: RidManager
......................... SERVER2008 passed test RidManager
Starting test: Services
......................... SERVER2008 passed test Services
Starting test: SystemLog
A warning event occurred. EventID: 0x8000001D
Time Generated: 03/08/2012 09:59:45
Event String:
The Key Distribution Center (KDC) cannot find a suitable certificate
to use for smart card logons, or the KDC certificate could not be verified. Sma
rt card logon may not function correctly if this problem is not resolved. To cor
rect this problem, either verify the existing KDC certificate using certutil.exe
or enroll for a new KDC certificate.
An error event occurred. EventID: 0xC0001B61
Time Generated: 03/08/2012 10:09:56
Event String:
A timeout was reached (30000 milliseconds) while waiting for the Liv
eUpdate service to connect.
An error event occurred. EventID: 0xC0001B58
Time Generated: 03/08/2012 10:09:56
Event String:
The LiveUpdate service failed to start due to the following error:
......................... SERVER2008 failed test SystemLog
Starting test: VerifyReferences
......................... SERVER2008 passed test VerifyReferences
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test
CrossRefValidation
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test
CrossRefValidation
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Running partition tests on : BREG
Starting test: CheckSDRefDom
......................... BREG passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... BREG passed test CrossRefValidation
Running enterprise tests on : BREG.local
Starting test: LocatorCheck
......................... BREG.local passed test LocatorCheck
Starting test: Intersite
......................... BREG.local passed test Intersite
C:\Users\Administrator>
I did nslookup:
C:\Users\Administrator>nslookup
Default Server: UnKnown
Address: ::1
and this:
C:\Users\Administrator>ntdsutil
ntdsutil: roles
fsmo maintenance: connections
server connections: connect to server server2008
Binding to server2008 ...
Connected to server2008 using credentials of locally logged on user.
server connections: q
fsmo maintenance: select operation target
select operation target: list roles for connected server
Server "server2008" knows about 5 roles
Schema - CN=NTDS Settings,CN=SERVER2008,CN=Servers,CN=Default-First-Site-Name,CN
=Sites,CN=Configuration,DC=BREG,DC=local
Naming Master - CN=NTDS Settings,CN=SERVER2008,CN=Servers,CN=Default-First-Site-
Name,CN=Sites,CN=Configuration,DC=BREG,DC=local
PDC - CN=NTDS Settings,CN=SERVER2008,CN=Servers,CN=Default-First-Site-Name,CN=Si
tes,CN=Configuration,DC=BREG,DC=local
RID - CN=NTDS Settings,CN=SERVER2008,CN=Servers,CN=Default-First-Site-Name,CN=Si
tes,CN=Configuration,DC=BREG,DC=local
Infrastructure - CN=NTDS Settings,CN=SERVER2008,CN=Servers,CN=Default-First-Site
-Name,CN=Sites,CN=Configuration,DC=BREG,DC=local
select operation target:
Did also slmgr.vbs /dli and got:
name:Windows Server(R) ServerWinFoundation edition
Description: Windows operating System - Windows Server(R),
OEM_COA_NSLP channel
Partial product key:.......
License Status:Licensed
thanks for help, in advanceI forgot to say that it is the only DC in the domain.
and this is DNS test
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
* Verifying that the local machine server2008, is a Directory Server.
Home Server = server2008
* Connecting to directory service on server server2008.
* Identified AD Forest.
Collecting AD specific global data
* Collecting site info.
Calling ldap_search_init_page(hld,CN=Sites,CN=Configuration,DC=BREG,DC=local,LDAP_SCOPE_SUBTREE,(objectCategory=ntDSSiteSettings),.......
The previous call succeeded
Iterating through the sites
Looking at base site object: CN=NTDS Site Settings,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=BREG,DC=local
Getting ISTG and options for the site
* Identifying all servers.
Calling ldap_search_init_page(hld,CN=Sites,CN=Configuration,DC=BREG,DC=local,LDAP_SCOPE_SUBTREE,(objectClass=ntDSDsa),.......
The previous call succeeded....
The previous call succeeded
Iterating through the list of servers
Getting information for the server CN=NTDS Settings,CN=SERVER2008,CN=Servers,CN=Default-First-Site-Name,CN=Sites,CN=Configuration,DC=BREG,DC=local
objectGuid obtained
InvocationID obtained
dnsHostname obtained
site info obtained
All the info for the server collected
* Identifying all NC cross-refs.
* Found 1 DC(s). Testing 1 of them.
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site-Name\SERVER2008
Starting test: Connectivity
* Active Directory LDAP Services Check
Determining IP4 connectivity
* Active Directory RPC Services Check
......................... SERVER2008 passed test Connectivity
Doing primary tests
Testing server: Default-First-Site-Name\SERVER2008
Test omitted by user request: Advertising
Test omitted by user request: CheckSecurityError
Test omitted by user request: CutoffServers
Test omitted by user request: FrsEvent
Test omitted by user request: DFSREvent
Test omitted by user request: SysVolCheck
Test omitted by user request: KccEvent
Test omitted by user request: KnowsOfRoleHolders
Test omitted by user request: MachineAccount
Test omitted by user request: NCSecDesc
Test omitted by user request: NetLogons
Test omitted by user request: ObjectsReplicated
Test omitted by user request: OutboundSecureChannels
Test omitted by user request: Replications
Test omitted by user request: RidManager
Test omitted by user request: Services
Test omitted by user request: SystemLog
Test omitted by user request: Topology
Test omitted by user request: VerifyEnterpriseReferences
Test omitted by user request: VerifyReferences
Test omitted by user request: VerifyReplicas
Starting test: DNS
DNS Tests are running and not hung. Please wait a few minutes...
See DNS test in enterprise tests section for results
......................... SERVER2008 passed test DNS
Running partition tests on : ForestDnsZones
Test omitted by user request: CheckSDRefDom
Test omitted by user request: CrossRefValidation
Running partition tests on : DomainDnsZones
Test omitted by user request: CheckSDRefDom
Test omitted by user request: CrossRefValidation
Running partition tests on : Schema
Test omitted by user request: CheckSDRefDom
Test omitted by user request: CrossRefValidation
Running partition tests on : Configuration
Test omitted by user request: CheckSDRefDom
Test omitted by user request: CrossRefValidation
Running partition tests on : BREG
Test omitted by user request: CheckSDRefDom
Test omitted by user request: CrossRefValidation
Running enterprise tests on : BREG.local
Starting test: DNS
Test results for domain controllers:
DC: server2008.BREG.local
Domain: BREG.local
TEST: Authentication (Auth)
Authentication test: Successfully completed
TEST: Basic (Basc)
The OS
Microsoft Windows Server 2008 R2 Foundation (Service Pack level: 1.0)
is supported.
NETLOGON service is running
kdc service is running
DNSCACHE service is running
DNS service is running
DC is a DNS server
Network adapters information:
Adapter
[00000007] Intel(R) 82566DM-2 Gigabit Network Connection:
MAC address is 00:19:99:86:E9:62
IP Address is static
IP address: 192.168.1.250
DNS servers:
192.168.1.250 (server2008.breg.local.) [Valid]
127.0.0.1 (server2008.breg.local.) [Valid]
The A host record(s) for this DC was found
The SOA record for the Active Directory zone was found
The Active Directory zone on this DC/DNS server was found primary
Root zone on this DC/DNS server was not found
TEST: Forwarders/Root hints (Forw)
Recursion is enabled
Forwarders are not configured on this DNS server
Root hint Information:
Name: a.root-servers.net. IP: 198.41.0.4 [Valid]
Name: a.root-servers.net. IP: 2001:503:ba3e::2:30 [Invalid (unreachable)]
Name: b.root-servers.net. IP: 192.228.79.201 [Valid]
Name: c.root-servers.net. IP: 192.33.4.12 [Valid]
Name: d.root-servers.net. IP: 128.8.10.90 [Valid]
Name: d.root-servers.net. IP: 2001:500:2d::d [Invalid (unreachable)]
Name: e.root-servers.net. IP: 192.203.230.10 [Valid]
Name: f.root-servers.net. IP: 192.5.5.241 [Valid]
Name: f.root-servers.net. IP: 2001:500:2f::f [Invalid (unreachable)]
Name: g.root-servers.net. IP: 192.112.36.4 [Valid]
Name: h.root-servers.net. IP: 128.63.2.53 [Valid]
Name: h.root-servers.net. IP: 2001:500:1::803f:235 [Invalid (unreachable)]
Name: i.root-servers.net. IP: 192.36.148.17 [Valid]
Name: i.root-servers.net. IP: 2001:7fe::53 [Invalid (unreachable)]
Name: j.root-servers.net. IP: 192.58.128.30 [Valid]
Name: j.root-servers.net. IP: 2001:503:c27::2:30 [Invalid (unreachable)]
Name: k.root-servers.net. IP: 193.0.14.129 [Valid]
Name: k.root-servers.net. IP: 2001:7fd::1 [Invalid (unreachable)]
Name: l.root-servers.net. IP: 199.7.83.42 [Valid]
Name: l.root-servers.net. IP: 2001:500:3::42 [Invalid (unreachable)]
Name: m.root-servers.net. IP: 2001:dc3::35 [Invalid (unreachable)]
Name: m.root-servers.net. IP: 202.12.27.33 [Valid]
TEST: Delegations (Del)
Delegation information for the zone: BREG.local.
Delegated domain name: _msdcs.BREG.local.
DNS server: server2008.breg.local. IP:192.168.1.250 [Valid]
TEST: Dynamic update (Dyn)
Warning: Failed to add the test record dcdiag-test-record in zone BREG.local
[Error details: 9017 (Type: Win32 - Description: DNS bad key.)]
Test record dcdiag-test-record deleted successfully in zone BREG.local
TEST: Records registration (RReg)
Network Adapter
[00000007] Intel(R) 82566DM-2 Gigabit Network Connection:
Matching CNAME record found at DNS server 192.168.1.250:
cb30439d-35e0-4add-ae6c-e7f281295520._msdcs.BREG.local
Matching A record found at DNS server 192.168.1.250:
server2008.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.221dc40b-9d51-48cf-a3a3-e3daf251197f.domains._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._tcp.dc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.dc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._tcp.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._udp.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kpasswd._tcp.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.Default-First-Site-Name._sites.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._tcp.Default-First-Site-Name._sites.dc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.Default-First-Site-Name._sites.dc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._tcp.Default-First-Site-Name._sites.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.gc._msdcs.BREG.local
Matching A record found at DNS server 192.168.1.250:
gc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_gc._tcp.Default-First-Site-Name._sites.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.Default-First-Site-Name._sites.gc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.pdc._msdcs.BREG.local
Matching CNAME record found at DNS server 192.168.1.250:
cb30439d-35e0-4add-ae6c-e7f281295520._msdcs.BREG.local
Matching A record found at DNS server 192.168.1.250:
server2008.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.221dc40b-9d51-48cf-a3a3-e3daf251197f.domains._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._tcp.dc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.dc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._tcp.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._udp.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kpasswd._tcp.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.Default-First-Site-Name._sites.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._tcp.Default-First-Site-Name._sites.dc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.Default-First-Site-Name._sites.dc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_kerberos._tcp.Default-First-Site-Name._sites.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.gc._msdcs.BREG.local
Matching A record found at DNS server 192.168.1.250:
gc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_gc._tcp.Default-First-Site-Name._sites.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.Default-First-Site-Name._sites.gc._msdcs.BREG.local
Matching SRV record found at DNS server 192.168.1.250:
_ldap._tcp.pdc._msdcs.BREG.local
Summary of test results for DNS servers used by the above domain
controllers:
DNS server: 2001:500:1::803f:235 (h.root-servers.net.)
1 test failure on this DNS server
PTR record query for the 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa failed on the DNS server 2001:500:1::803f:235
[Error details: 1460 (Type: Win32 - Description: This operation returned because the timeout period expired.)]
DNS server: 2001:500:2d::d (d.root-servers.net.)
1 test failure on this DNS server
PTR record query for the 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa failed on the DNS server 2001:500:2d::d
[Error details: 1460 (Type: Win32 - Description: This operation returned because the timeout period expired.)]
DNS server: 2001:500:2f::f (f.root-servers.net.)
1 test failure on this DNS server
PTR record query for the 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa failed on the DNS server 2001:500:2f::f
[Error details: 1460 (Type: Win32 - Description: This operation returned because the timeout period expired.)]
DNS server: 2001:500:3::42 (l.root-servers.net.)
1 test failure on this DNS server
PTR record query for the 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa failed on the DNS server 2001:500:3::42
[Error details: 1460 (Type: Win32 - Description: This operation returned because the timeout period expired.)]
DNS server: 2001:503:ba3e::2:30 (a.root-servers.net.)
1 test failure on this DNS server
PTR record query for the 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa failed on the DNS server 2001:503:ba3e::2:30
[Error details: 1460 (Type: Win32 - Description: This operation returned because the timeout period expired.)]
DNS server: 2001:503:c27::2:30 (j.root-servers.net.)
1 test failure on this DNS server
PTR record query for the 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa failed on the DNS server 2001:503:c27::2:30
[Error details: 1460 (Type: Win32 - Description: This operation returned because the timeout period expired.)]
DNS server: 2001:7fd::1 (k.root-servers.net.)
1 test failure on this DNS server
PTR record query for the 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa failed on the DNS server 2001:7fd::1
[Error details: 1460 (Type: Win32 - Description: This operation returned because the timeout period expired.)]
DNS server: 2001:7fe::53 (i.root-servers.net.)
1 test failure on this DNS server
PTR record query for the 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa failed on the DNS server 2001:7fe::53
[Error details: 1460 (Type: Win32 - Description: This operation returned because the timeout period expired.)]
DNS server: 2001:dc3::35 (m.root-servers.net.)
1 test failure on this DNS server
PTR record query for the 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.ip6.arpa failed on the DNS server 2001:dc3::35
[Error details: 1460 (Type: Win32 - Description: This operation returned because the timeout period expired.)]
DNS server: 128.63.2.53 (h.root-servers.net.)
All tests passed on this DNS server
DNS server: 128.8.10.90 (d.root-servers.net.)
All tests passed on this DNS server
DNS server: 192.112.36.4 (g.root-servers.net.)
All tests passed on this DNS server
DNS server: 192.168.1.250 (server2008.breg.local.)
All tests passed on this DNS server
Name resolution is functional._ldap._tcp SRV record for the forest root domain is registered
DNS delegation for the domain _msdcs.BREG.local. is operational on IP 192.168.1.250
DNS server: 192.203.230.10 (e.root-servers.net.)
All tests passed on this DNS server
DNS server: 192.228.79.201 (b.root-servers.net.)
All tests passed on this DNS server
DNS server: 192.33.4.12 (c.root-servers.net.)
All tests passed on this DNS server
DNS server: 192.36.148.17 (i.root-servers.net.)
All tests passed on this DNS server
DNS server: 192.5.5.241 (f.root-servers.net.)
All tests passed on this DNS server
DNS server: 192.58.128.30 (j.root-servers.net.)
All tests passed on this DNS server
DNS server: 193.0.14.129 (k.root-servers.net.)
All tests passed on this DNS server
DNS server: 198.41.0.4 (a.root-servers.net.)
All tests passed on this DNS server
DNS server: 199.7.83.42 (l.root-servers.net.)
All tests passed on this DNS server
DNS server: 202.12.27.33 (m.root-servers.net.)
All tests passed on this DNS server
Summary of DNS test results:
Auth Basc Forw Del Dyn RReg Ext
Domain: BREG.local
server2008 PASS PASS PASS PASS WARN PASS n/a
......................... BREG.local passed test DNS
Test omitted by user request: LocatorCheck
Test omitted by user request: Intersite -
Error in XI Dispacher running server not connected 503 service unavailable
Hi All,
We are facing a problem in SAP XI 3.0, we are having two SLD . Both Development and Quality are in One SLD and production is in a different SLD. We found error "<b>Dispatcher running but no server connected</b>! 503 service unavilable" in our QA system and this error happened in peak time only. We are using OS AS400/DB2 and Java SP 16 is udated in our systems. We didnt found any perticular error in Work Directory log file also . pls give solution to resolve this error.
Kind Rgds,
Gopinath.hey
have a look at the following
Re: Dispatcher running but server no connected
Dispatcher running, but no server connected!!!! (Anybody out there)
Dispatcher Running; Server could not be connected
thanx
ahmad -
Reporting Services Server cannot connect to the DPM database. ( dpm 2010 )
Reporting Services Server cannot connect to the DPM database.
To repair the configuration, follow steps for repairing DPM from DPM Setup Help.
ID: 3001
i can not try the Recommended action from error codes catalog because i did not found Change reporting
passwordHi,
We have had several customers report this after installing DPM 2012 R2.
To get past the below error while scheduling reports to be mailed.
Reporting Services Server cannot connect to the DPM database.
To repair the configuration, follow steps for repairing DPM from DPM Setup Help.
ID: 3001
Perform the following steps as necessary:
1. Created a new local group called "DPMDBReaders$<DPMServerName>"
2. Created a new user called, "DPMR$<DPMServerName>" and added this user to DPMDBReader group that we created on step 1.
3. Open SQL management studio and add the DPMDBReaders$<DPMServerName group to Logins under Security in SQL Management Studio.
4. Modify the properties and under General – change the default database to the current DPMDB name.
5. Under User Mapping – select the current DPMDB name and check the db_datareader checkbox.
6. In SQL Management Studio, navigate to the Databases > DPMDB > Security > Users > and select the DPMDBReaders$<DPMServerName>" group.
Right-click the DPMDBReaders$<DPMServerName>" group and select properties. Under the
Securables section, click on Search. On the add objects dialog, click OK.
On the Select Objects dialog, click the Objects type, then check the
stored procedure checkbox. Browse and add the following two stored procedures
“Prc_MOM_Heartbeat_Get” and “prc_MOM_ProductionServer_Get”. Grant the Execute permission for both of the stored procedures added.
7. In SQL Reporting Services Configuration manager, under Report Manager URL - click on the link to open the portal (http://localhost/Reports)
i. Click on the DPMReoprts_GUID to open the DPM reports.
ii. Click on the DPMReporterDataSource
iii. On the poperties page, enabled "Credentials stored securely in the report server" on DPMReporterDataSource configuration page and added “DPMR$<DPMServerName>” user account that we created in step 2.
iv. tick "Use as Windows credentials when connecting to the data source."
v. Click ‘Test connection’ on the same page to verify whether it can connect successfully.
8. In SQL Reporting configuration manager - change the Service Account to use build-in account: Network Service
9. Reboot the DPM Server.
10. You should then be able to schedule e-mailed reports.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT] This
posting is provided "AS IS" with no warranties, and confers no rights. -
How do I setup a php testing server that connects to my web host?
My web host (webhostingpad.com) has php on it. I need to setup a testing server that connects to this so I can test my site locally.
My questions are:
1. Do I set this up as a local network connection or an sftp (same as my remote)?
2. what information do I put in to make this work?1024MB is enough to have 2 instances but You have to know what are going to be the requirements levels of those instances in order to check if your memory is enough.
The memory is a theme that relate Oracle SGA with RAM in the machine.
To have a second database server you have to make another installation in a different Oracle Home.
It is not the same to have 2 instances than 2 Oracle database servers.
Do you know what is the difference ?
Joel P�rez -
Content Server SQL Server 2000 Connection Error (very annoying)
All of the diagnostic tests are failing because of SQLServer connection error (see below for diagnosticTests.jsp output).
I checked database.content.properties file, all connection information is correct. The portal is running on the same SQL server. So I know that the SQL server is running just fine. I just could not isolate the problem. Can you help?------------------------------------------------------------------------
Content Server DB Connection FAIL
Settings JDBC Driver: com.plumtree.jdbc.sqlserver.SQLServerDriver JDBC URL: jdbc:plumtree:sqlserver://OXO-SRV03:1433;DatabaseName=ptcsdb DB Driver: com.plumtree.jdbc.sqlserver.SQLServerDriver DB Vendor: com.plumtree.content.rdbms.impl.VendorSqlServer User Name: ptcsdbuser Possible Resolution Check the Content DB JDBC Server, JDBC Port, JDBC User, JDBC Password, and JDBC Databse settings in the content.properties file. Error Details Exception Message: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect com.plumtree.jdbc.base.BaseSQLException: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect at com.plumtree.jdbc.base.BaseExceptions.createException(Unknown Source) at com.plumtree.jdbc.base.BaseExceptions.getException(Unknown Source) at com.plumtree.jdbc.sqlserver.tds.TDSConnection.(Unknown Source) at com.plumtree.jdbc.sqlserver.SQLServerImplConnection.open(Unknown Source) at com.plumtree.jdbc.base.BaseConnection.connect(Unknown Source) at com.plumtree.jdbc.base.BaseConnectionStartup.run(Unknown Source) Content DB Table CREATE and DELETE FAIL
Settings Unable to get a connection to the content server DB Possible Resolution Check the Content DB JDBC Server, JDBC Port, JDBC User, JDBC Password, and JDBC Databse settings in the content.properties file. Also ensure that the Content Database Server is running. Error Details Exception Message: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect com.plumtree.jdbc.base.BaseSQLException: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect at com.plumtree.jdbc.base.BaseExceptions.createException(Unknown Source) at com.plumtree.jdbc.base.BaseExceptions.getException(Unknown Source) at com.plumtree.jdbc.sqlserver.tds.TDSConnection.(Unknown Source) at com.plumtree.jdbc.sqlserver.SQLServerImplConnection.open(Unknown Source) at com.plumtree.jdbc.base.BaseConnection.connect(Unknown Source) at com.plumtree.jdbc.base.BaseConnectionStartup.run(Unknown Source) Content DB Update and Query FAIL
Settings Unable to get a connection to the Content DB Table Name: PCSSYSTEM Column Name: CREATEDVERSION Possible Resolution Check the Content DB JDBC Server, JDBC Port, JDBC User, JDBC Password, and JDBC Databse settings in the content.properties file. Also ensure that the Content Database Server is running. Error Details Exception Message: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect com.plumtree.jdbc.base.BaseSQLException: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect at com.plumtree.jdbc.base.BaseExceptions.createException(Unknown Source) at com.plumtree.jdbc.base.BaseExceptions.getException(Unknown Source) at com.plumtree.jdbc.sqlserver.tds.TDSConnection.(Unknown Source) at com.plumtree.jdbc.sqlserver.SQLServerImplConnection.open(Unknown Source) at com.plumtree.jdbc.base.BaseConnection.connect(Unknown Source) at com.plumtree.jdbc.base.BaseConnectionStartup.run(Unknown Source) Portal DB Connection FAIL
Settings JDBC Driver: com.plumtree.jdbc.sqlserver.SQLServerDriver JDBC URL: jdbc:plumtree:sqlserver://OXO-SRV03:1433;DatabaseName=plumdb DB Driver: com.plumtree.jdbc.sqlserver.SQLServerDriver DB Vendor: com.plumtree.content.rdbms.impl.VendorSqlServer User Name: plumdbuser Possible Resolution Check the Portal DB JDBC Server, JDBC Port, JDBC User, JDBC Password, and JDBC Databse settings in the content.properties file. Error Details Exception Message: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect com.plumtree.jdbc.base.BaseSQLException: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect at com.plumtree.jdbc.base.BaseExceptions.createException(Unknown Source) at com.plumtree.jdbc.base.BaseExceptions.getException(Unknown Source) at com.plumtree.jdbc.sqlserver.tds.TDSConnection.(Unknown Source) at com.plumtree.jdbc.sqlserver.SQLServerImplConnection.open(Unknown Source) at com.plumtree.jdbc.base.BaseConnection.connect(Unknown Source) at com.plumtree.jdbc.base.BaseConnectionStartup.run(Unknown Source) Portal DB Query FAIL
Settings Unable to get a connection to the Portal DB Table Name: PTUSERS Column Name: OWNERID Possible Resolution Check the Portal DB JDBC Server, JDBC Port, JDBC User, JDBC Password, and JDBC Databse settings in the content.properties file. Also ensure that the Portal Database Server is running. Error Details Exception Message: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect com.plumtree.jdbc.base.BaseSQLException: [plumtree][SQLServer JDBC Driver]Error establishing socket. Connection refused: connect at com.plumtree.jdbc.base.BaseExceptions.createException(Unknown Source) at com.plumtree.jdbc.base.BaseExceptions.getException(Unknown Source) at com.plumtree.jdbc.sqlserver.tds.TDSConnection.(Unknown Source) at com.plumtree.jdbc.sqlserver.SQLServerImplConnection.open(Unknown Source) at com.plumtree.jdbc.base.BaseConnection.connect(Unknown Source) at com.plumtree.jdbc.base.BaseConnectionStartup.run(Unknown Source) Document Repository OK Workflow Server FAIL
Settings Workflow Server Base URL: http://OXO-SRV03:7087 Content Server URL: http://OXO-SRV03:7777/ptcs Workflow Server Portlet URL: http://OXO-SRV03:7087/workflow Possible Resolution Verify that the Plumtree Workflow service has been started. Also, check the Workflow Serverdiagnostics for more detailed information. Error Details Exception Message: Cannot access Burlap service at [http://localhost:7087/wfserver/caucho/workflowsvc-burlap]; nested exception is com.caucho.burlap.client.BurlapProtocolException: org.springframework.remoting.RemoteAccessException: Cannot access Burlap service at [http://localhost:7087/wfserver/caucho/workflowsvc-burlap]; nested exception is com.caucho.burlap.client.BurlapProtocolException: com.caucho.burlap.client.BurlapProtocolException: at com.caucho.burlap.client.BurlapProxy.invoke(BurlapProxy.java:171) at $Proxy2.connectPortalUser(Unknown Source) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:324) at org.springframework.remoting.caucho.BurlapClientInterceptor.invokeDon't know if anyone is still having problems with this, but just in case...
I was getting a similar error. I had an Event Viewer record (It wasn't a Warning or an Error, just an Information) reading:You are running a version of Microsoft SQL Server 2000 or Microsoft SQL Server 2000 Desktop Engine (also called MSDE) that has known security vulnerabilities when used in conjunction with this version of Windows. To reduce your computer's vulnerability to certain virus attacks, the TCP/IP and UDP network ports of Microsoft SQL Server 2000, MSDE, or both have been disabled. To enable these ports, you must install a patch, or the most recent service pack for Microsoft SQL Server 2000 or MSDE from http://www.microsoft.com/sql/downloads/default.asp
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
I installed SQL SP4 and it corrected the problem -
How to identify which server are connected in a switch?
Hi,
Many servers are connected to a switch?
How to identify what server are connected to which port remotely?
Thanks!
SamuelHi Sam,
just issue the command show ip arp , it will display some thing like this for know the MAC address & the VLAN number.
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.2.1.18 9 0800.6913.710e ARPA Vlan2
to know on which port it is connected, just issue the command as mentioned below
sh mac-address-table address 0800.6913.710e
Mac Address Table
Vlan Mac Address Type Ports
2 0800.6913.710e DYNAMIC Po1
hpe this will help you to identify your servers.
rate this post. -
Error:java.sql.SQLException: [Microsoft][ODBC SQL Server Driver]Connection
Hi,
while running jsp page i m getting error as follows:
java.sql.SQLException: [Microsoft][ODBC SQL Server Driver]Connection is busy with results for another hstmt..
what is this error...
what should i do to solve this problem...
plz let me know what is this error & how to solve this...
Thanx in advance....Why don't you do a search in google with the excpetion?
If you cannot then try this link
[http://www.idssoftware.com/faq-e.html] -
Java - SQL Server 2000 Connectivity
hi all. i m looking for help in Java - SQL Server 2000 Connectivity.i worked on Java- Oracle & Java - MS Access format.now i m looking to work on Java - SQL Server 2000. I m using JBuilder 2005. can any1 help me how to make any change(configuration) in my SQL Server.thanx in advance.
http://www.jguru.com/forums/JBuilder is hopeless. ihvn;t get good replies from them.i downloaded the JDBC driver from microsoft and added the JAR files (3 files) and tried the following code:
import java.sql.*;
* Microsoft SQL Server JDBC test program
public class Test {
public Test() throws Exception {
// Get connection
DriverManager.registerDriver(new com.microsoft.jdbc.sqlserver.SQLServerDriver());
//Connection connection = DriverManager.getConnection("jdbc:microsoft:sqlserver://<Host>:1433",<"UID>","<PWD>");
// Connection connection = DriverManager.getConnection("jdbc:microsoft:sqlserver://GMC01:1433;DatabaseName=MoonDB");
Connection connection = DriverManager.getConnection("jdbc:microsoft:sqlserver://Moon:1433;DatabaseName=MoonDB");
if (connection != null) {
System.out.println();
System.out.println("Successfully connected");
System.out.println();
// Meta data
DatabaseMetaData meta = connection.getMetaData();
System.out.println("\nDriver Information");
System.out.println("Driver Name: "
+ meta.getDriverName());
System.out.println("Driver Version: "
+ meta.getDriverVersion());
System.out.println("\nDatabase Information ");
System.out.println("Database Name: "
+ meta.getDatabaseProductName());
System.out.println("Database Version: "+
meta.getDatabaseProductVersion());
} // Test
public static void main (String args[]) throws Exception {
Test test = new Test();
it run without any error and then showed fatal exception as below:
java.sql.SQLException: [Microsoft][SQLServer 2000 Driver for JDBC]Error establishing socket.
at com.microsoft.jdbc.base.BaseExceptions.createException(Unknown Source)
at com.microsoft.jdbc.base.BaseExceptions.getException(Unknown Source)
at com.microsoft.jdbc.base.BaseExceptions.getException(Unknown Source)
at com.microsoft.jdbc.sqlserver.tds.TDSConnection.<init>(Unknown Source)
at com.microsoft.jdbc.sqlserver.SQLServerImplConnection.open(Unknown Source)
at com.microsoft.jdbc.base.BaseConnection.getNewImplConnection(Unknown Source)
at com.microsoft.jdbc.base.BaseConnection.open(Unknown Source)
at com.microsoft.jdbc.base.BaseDriver.connect(Unknown Source)
at java.sql.DriverManager.getConnection(DriverManager.java:512)
at java.sql.DriverManager.getConnection(DriverManager.java:193)
at Test.<init>(Test.java:11)
at Test.main(Test.java:31)
Exception in thread "main"
where's the problem?can any1 try to solve this plz.
Maybe you are looking for
-
Manipulation of Print form after generation
I am using Adobe Forms as print forms within the SAP ERP 5.0 without WebDynpro. I have requirement that I need to manipulate the generated PDF file by adding additional attachment files to the PDF generated by the function module. Technically this se
-
all buttons or tabs in the gray bar (including today/next day/week/month) are gray and can't be selected. how do i enable them?
-
Acrobat 9 pro, Mac OS X 10.10.3, Inatlationsfehler
Nach der NEU Installation von Yosemite 10.10.3 läuft die Installation von Acrobat 9 pro nur, wenn man das ADOBE PDF Viewer Safari-Plug-In nicht aktiviert (sonst bleibt die Installation stehen). Beim Update der Version 9.3.2 auf 9.5.5 erscheint ein Fe
-
Can't see my network shared folders(on PCs)
I have a home network with D-Link router with 3 other computers (2 WinXP and a Vista). The computers are all on the same subnet 192.168.0.10X and all use DHCP from the Router. The Macbook is getting an IP from the router but it doesn't see the other
-
Report Painter/Writer Best Practice?
Is it a good idea to create Reports using Report Writer/Painter in a Productive environment? or is it better to create them in a Dev system & transport them to Production like any other custom development Object? I would appreciate if you can share y