Digital connection to 5.1 speakers : output on the rear of the ca

I would like to connect a soundblaster card to my Logitech Z-5500 5. speakers, via a digital connection cable. I would like to know if I will need to connect the speakers on the rack that comes with the S.B. X-FI Platinium (front side of the PC), or is it possible to digitally connect the speakers on the sound card itself (rear of the PC)?Thanks in advance for the information,-g

PJC's information is correct and I would only add one bit of information. You will need to configure your DVD playing software for SPDIF output as well as disable the THX certified Dolby Digital decoder on the soundcard. This will allow the signal to be passed through the DVD software and the soundcard so that your Logitech speakers can handle the decoding.
If you would prefer to use the X-Fi's decoder and sound features, you will need to use the analog inputs on the speakers as per Logitech's recommendation in the manual. They intend the other inputs for external devices such as a DVD player. By using the analog inputs, you will have the proper software controls over the Dolby Digital decoding as well as the THX optimization settings.
Daniel

Similar Messages

Front speakers sound switches to rear speakers

X-Fi Xtreme Gamer Fatalty Professional Series
4gig RAM
E6850
X48 Chip
x64 Vista Ultimate
Creative 5. speakers
Driver: SBXF_PCDRV_LB_2_8_0008
Gaming Mode at all times
When listening music or watching film all of a sudon my L-Front, Center and R-Front speaker di'vert the sound to the L-Rear and R-Rear speakers and then after sometime they switch it back to the front speakers. This happenends in entertainment mode aswell in gaming mode. Also when using teamspeak the sound is beeing switched this is verry anoying when playing a game.
Any solution to this?

Re: Front speakers sound switches to rear speakers$ X-fi Extreme Gamer
4gig Ram
AMD PhenomX4
8800 GTS
Vista Home Premium 64
Yamaha 7. receiver
3.5mm to RCA cables
You are lucky. I am yet to setup front speakers at ALL on a 7. system. The sound card simply wont output the separate channels correctly.
The front speakers output on the Back rear speakers. The subwoofer outputs on the centre speaker and the centrespeaker works on the subwoofer depending what Mood the sound card is in.
I have tried different cables and the problem has been identified specificly as the sound card.
The only reason i bought one of these cards was becos my motherboard sound died, i had no problems like this before getting a soundblaster.

How do you disable "digital optical output" so the red light in headphone jack goes off and I can use the internal speakers?

HI,
I have a red light in my headphone jack and I see "correct responses" listed as "when digital output is enabled speakers are disabled." That's all well and good but doens't really help. HOW do you disable the "digital output," get the red light to turn off and be able to hear through the speakers? What's the SOLUTION to the problem. Sorry, just a bit frustrated. Any help is greatly appreciated.
Best,
dpeast12

Allegedly this can occur if there is a contaminant in the headphone jack that makes the computer believe there is an optical connection there, so it shuts off the internal speakers.
Try inserting and removing a headphone plug repeatedly. This ought to dislodge the junk, and seems to have fixed the problem for others. Hope it helps!

How can I connect my non 5.1 output DVD to my great Inspire speakers??

hello there, new in the forum; well.. basicly that:
My DVD doesn't have the 5.1 output jacks, it only has the digital coaxial RCA output; how can I connect it to my brand new and already awesome Inspire speakers.
Thanks in advance.

It is possible to get a seperate decoder such as the one offered by Creative, but in my opinion the easiest route is to simply buy a new dvd player.
From a previous reply:
Note about some dvd players: If your player doesn't have 5.1 channel outputs like the pictured one does, then you will need to get a player that does. Unfortuantly, most basic dvd players do not include these outputs anymore because digital surround sound receivers are so affordable and readily avalible. Therefore, in order to be guaranteed that your new player will have these outputs, look for a dvd player that also plays dvd audio and/or sacd. These players MUST have these outputs for the multi-channel audio playback, and most can also output the dvd signal through these outputs.
Also, a lot of cheapie players sold at small movie and music stores have 5.1 outputs, but check before you buy. Good Luck!

Audigy 4 pro digital connection but no l

Hi
I have a soundblaster audigy 4 pro and i connect it to my amblifier denon with optical cable but when i play a dolby digital or dts sound i can't get the logo on the amblifier. I test it on clean install win xp sp2. The sound seems to bo ok but no logo. I use Power dvd latest version.When i play the same dvd on my desktop dvd player with optical connection everything is ok sound and all logo's display.
Do i have to enable cmss?
Please help.
Thank you
P.S sorry for my bad english.Message Edited by ASTRAPI on 06-2-2005 0:30 AM

CMSS is an effect used for stereo sounds, to emulate surround sound for them. It has no effect on the DVDs you're playing as you're just outputting the AC3 signal so the speakers can decode it.
If you're using a digital connection, then CMSS will not have any effect for other sound either, you need to connect through multiple analog connections to get that sound. A standard digital connection (coaxial and optical SPDIF) can only pass over either a stereo PCM signal, or an encoded AC3 stream (like on your DVDs). Normal sound like music or games will only be passed over as stereo PCM, so there is no CMSS effect there.
If you can connect your amplifier through several analog connections, then you can use CMSS aswell, otherwise your amplifier might have it's own upmix option like ProLogic.
Cat

4-pole Minijack-toRCA? (Digitally connect Audigy 2 SZ to Inspire 5500 speakerset)

Hello forum/Creative,
After searching and searching, I'm just confused. And I'm quite an audiophile and I know quite a lot about cable and connections. I still have a problem getting (Dolby) Digital from my Audigy 2 SZ card, to my Creative 5500 (Digital) speakerset. There's a couple "paradoxes" if you will so I hope someone (of Creative) can explain this to me.Because my situation is different than everything I read before.Now the "problem" is that the 5500 digital speakerset uses an external Dolby Digital decoder that is connected to the subwoofer by a DIN-to-DIN cable. Then there are the 3 minijacks (output) that connect from the decoder to the sub. (This also enable volume control per channel via the external decoder/remote) Then there's a coaxial (digital) input that goes from the decoder to any digital out source, which at first was at the coaxial out of my DVD player, which gave the Dolby Digital 5. channel sound as it should. No problem so far.But then I bought an Audigy 2 SZ card for my pc and the problems is that the Digital Out of this card is not a coaxial one, but a minijack output.Strangly however, the 5500 speakerset includes a minijack-to-rca cable, so I can connect the coaxial input on the decoder to the minijack digital out of the Audigy 2 SZ card. Then I got just front L/R channels. I realized the included cable was a 2-pole minijack, with one ground connection and audiostream (Front L/R) What I need is a 4-pole Minijack-to-RCA (. ground 2. Front L/R 3. Rear L/R 4. Sub/Center) , but I dumbfounded so far and I wonder if this cable even exists. After looking in the manuel again and checking the Creative forum and other audiofora, all I can see is a 4-pole minijack-to-DIN (digital din)Here'smy problem with that:st of all my external decoder is connected to the subwoofer via a DIN-to-DIN cable. So if I would get that 4pole Minijack-to-RCA my external decoder becomes nothing more then a nice piece of decoration. Since power from the sub goes to this decoder via the DIN cable (do I wonder if it's a Digital DIN at all)But since this decoder is also used to control volume (per channel) and has the infrared remote receiver + Dynamic Mode setting which can only be set via the remote, I would loose all these functions?I know the Audigy 2 SZ has it's own Dolby Digital (EX), DTS (ES) etc, but I don't want the soundcard output alone and not use the external decoder (again, since this decoder does more than just decode alone).Now a 4-pole Minijack-to-RCA would solve all these problems and I REALLY hope these exists. (Should be possible at least).Currently I have unplugged the 3 minijacks-to-minijacks from the external decoder and plugged them into my Audigy 2 SZ card for Analog Surround. But it doesn't sound good (well at least compared to real Dolby Digital) and via this setup I lost volume control (per channel) functionallity of the external decoder.So please help me out on this. I would really appreciate it.Regards,Felix.

P.S. The 4pole Minijack-to-RCA I mention is a female RCA connector to accept the male-to-male coaxial RCA cable. I also noticed the Audigy 2SZ Quick start manual states to hook up 5. digital speakers to use a 4pole minijack-to-4pole minijack, but this is impossible since there is only a coaxial input and minijack output.So a minijack-to-minijack cable is completely wrong. After (again) checking my Inspire 5500 user's guide, I noticed ONLY THIS manual has the ONLY correct solution to hook up the set. The aformentioned 4pole minijack-to-RCA (female).Creative, why do you supply a useless 2-pole minijack-to-RCA for the digital connection of the Inspire Dolby Digital 5500 speakerset instead of the 4pole one?I mean, you buy the Dolby Digital set to get real Dolby Digital sound, but to get that from your own Audigy (2 SZ) card, you need another cable!! (and when you get it, the other cable will never be used for anything else, since it can only transfer the Front L/R signal!!
Message Edited by Felix2 on 0-09-2006 05:43 PM

What speakers work with the Creative Labs DDTS-100 Digital Decoder-Upto 7.1

what speakers do the Creative Labs DDTS-100 Digital Decoder-Upto 7.1 work with thanks

Unless the Digital 5500 speaker set has analog inputs it can't be used with the DDTS-100. You must connect the DDTS-100 to a speaker system through the analog outputs either from the main unit or the switchbox. I have not heard of any cables to convert analog audio into digital form so digital speakers can understand and play it.
The best speaker system? I have absolutely no idea dude. You must be the judge of that, if it is you who are going to listen to it. I like my S750 system but that is me. You have to read loads of info and reviews and preferably listen to them in a store if you can.

@ sticky thread "Digital Connections, SPDIF.

Hi there,
In the thread is mentioned it is NOT possible to play games with surround sound over a digital connection because of the GAMES lack the possibility to encode Dolby:
PC Games
PC games usually use technologies like as EAX to create surround sound, not Dolby Digital. So even if your speaker system has a Dolby Digital decoder, it will be of no use when playing games. The EAX processing is done on the soundcard, and the 6-channel sound is output via the analogue (or digital DIN if available). So you still need analogue connections to your digital speakers for games, if you just use an optical/coax cable you will only get the front left/right sound.
(N.B. X-Box games do support Dolby Digital, so if you connect your X-Box to your Dolby Digital receiver/speakers with the optical cable, you can get full surround sound.)
I think this is not quite correct!
X-Box games do not support Dolby, it is the X-Box!
Sure, PC games do not encode their sound in Dolby, but it is the task of the soundcard to do so. Games create surround sound using EAX, directSound and APIs like that.
(by the way: Dolby Digital is no possibility to create surround sound, it is just an encoding of the final signal)
The digital surround sound, computed by the soundcard (that is why I have bought it, to have it create the sound, and not the CPU) is then passed to the digital interface for CL's speaker systems, or converted to an analog signal.
And there, on the soundcard, I am missing the ability to encode Dolby Digital.
There is no way games will provide Dolby, nor would it be useful to transfer the sound from the soundcard to the CPU and back again for this task.
Why is there no card supporting that? Would it be to expensi've?
What about a Sounblaster series like X-Fi Fatalty Pro Dolby?Message Edited by MCsnuffBobbyK on 08-04-2006 09:24 PM

finchy wrote:What?With all do respect Dale-Cl, don't tell pepople bull**bleep** 'cause I can't stand it anymore."This is because it takes much overhead to encode Dolby, and the sound card isn't fast enough to do this."Part me, but my 4 year-old INTERGRATED music chip (NVidia SoundStorm) can encode to Dolby Digital easily. So the X-fi Processor got more MiPS than Pentium 4 and still cannot handle encoding to DD? C'mon, people are not stupid. Every major card from other producer can encode it to DD and the best ones to DTS Connect.How about You are going to write straight that Creative Labs does NOT want pay licences for using above technologies? Even the worse true is better than constant cheating on your customers.RegardsFinch
The nVidia SoundStorm is the same chip as the one in XBox and it is a dedicated HARDWARE encoder. And nVidia doesn't have the license to produce it anymore. There is NO other sound card chip available now that can do hardware encoding. Only CMedia (not like you sayd "every major card") has some chips that can do software encoding, but from my experience with them, the CPU load is important and in games that is bad.Message Edited by SoNic2367 on 08-04-2006 06:50 PM

Digital Connections, SPDIF and Dolby Digital Info

I have noticed that many people have problems using their digital connections, so I put together this info to try and explain the difference between digital and analogue, and how to use them.
Digital ConnectionsDigital connections come in two standard forms, optical and coax. They both give you exactly the same result, the only difference is the medium (material) through which the signal travels. The thing to remember about digital is that for ordinary, uncompressed sound, it will only carry a stereo signal. So, if you like to use CMSS with your music, or you try the speaker test function, optical/coax is useless as you only hear the front left/right speakers.
Movies wth Dolby Digital (AC3) & DTSMovies on DVD often use encoded audio in the form of Dolby Digital (AC3) or DTS. This means that all 6 channels are compressed into a single stream of digital data. A decoder is required to extract the channels and send the sound to the correct speakers. There are three ways to do this.
) Pass the AC3/DTS signal to a external decoder. This is where your optical/coax connection is used. To go down this route, you must first have a set of speakers or a decoder that supports Dolby Digital. In your DVD software, select 'SPDIF' as the audio output method and 'SPDIF Pass-through' in your soundcard options. What this does is tells both the software and soundcard to leave the audio from the DVD in compressed form and send it straight through the digital outputs. Your digital speakers/receiver will do all the decoding to give you full surround sound. Please note that this is the only way to get 6 channels through an optical/coax cable.
2) Decode the AC3/DTS with your Sound Blaster.You should choose this option if you don't have an external decoder. In the DVD software, select 'SPDIF' as the audio output method and make sure that 'SPDIF Pass-through' in the souncard options is off. The DVD software will now pass the compressed audio to your soundcard, which will then decode the data. The soundcard will output the 6 channels using the analogue connections (or digital DIN, more on this later). If you try to use a digital optical/coax connection to your speakers, you will only hear faint sounds from the front left/right speakers.
3) Decode the AC3/DTS with software.If you have a soundcard that doesn't support Dolby Digital (like the SB Li've! 24-bit) and you don't have digital speakers, the only way for you to get surround sound in movies is to use software to decode the AC3/DTS. The free versions of DVD software you get with hardware often don't support this feature, you will most likely need a full version. First select 'Dolby Digital' or 'DTS' decoding in the DVD software audio options (you must select the right sound format for the movie you are watching). Then make sure that 'SPDIF Pass-through' in the soundcard options is off. As with method (2) you must connect your speakers with the 3 analogue cables, not optical/coax.
PC GamesPC games usually use technologies like as EAX to create surround sound, not Dolby Digital. So even if your speaker system has a Dolby Digital decoder, it will be of no use when playing games. The EAX processing is done on the soundcard, and the 6-channel sound is output via the analogue (or digital DIN if available). So you still need analogue connections to your digital speakers for games, if you just use an optical/coax cable you will only get the front left/right sound.(N.B. X-Box games do support Dolby Digital, so if you connect your X-Box to your Dolby Digital receiver/speakers with the optical cable, you can get full surround sound.)
Creative's 4-pole mini-jack & Digital DINYou can only get the full use out of this connection when used between Creative Sound Blasters and compatible Creative speaker systems. It is the digital equivalent of the analogue connections, but instead of using 3 stereo sockets, you use just one digital socket. There are 4 conducting connections in the socket (unlike coax which has two) so there are enough connections to carry 3 different digital stereo signals (front R/L, rear R/L and Sub/Centre). You will probably require a 4-pole mini-jack > DIN converter to connect your Creative speakers to this socket. Using this connection will allow you to get surround from games (unlike SPDIF). However the digital DIN input on some Creative speakers can't receive AC3/DTS data, so you may still require an optical/coax connection.
N.B. This digital socket on the Sound Blaster cards doubles as the digital coax output. If you don't have digital DIN, you can use a mono or stereo mini-jack > RCA converter to connect to the coax input on your speakers, as the front R/L or AC3/DTS signals are sent through the tip of the plug.
More InfoCreative's Speaker Conectivity Guide: http://support.creative.com/kb/ShowA....aspx?sid=5035
Dolby Surround info: http://www.dolby.com
I hope that clarifies the issue .
Message Edited by KokChoy-CL on 07-04-2008 :0 AM

Digital Connections, SPDIF and Dolby Digital (german revision)
Options
03-08-2007 01:52 AM
Digital Connections, SPDIF and Dolby Digital Info
Übersetzung + Erweiterungen + Revision 03-08-07
Der Digitale Anschluß
Ich habe beobachtet, daß viele Leute Fragen zu den Sound-Anschlüssen haben, daher trage ich hier einige Infos zusammen und erkläre die Unterschiede in der Verwendung der digitalen und analogen Anschlüsse.
Digitale Anschlüsse – S-PDIF & Toslink
Am PC gibt es zwei häufig verwendete digitale Anschlußformate optisch (Toslink) und koaxial (S-PDIF).
Im Prinzip erzielen beide Anschlüsse genau das gleiche Audio-Ergebnis.
Der primäre Unterschied ist das Medium ( das Material ) durch das das Signal übertragen wird. ( Glasfaser oder Kupfer )
!! Update !!
Ein wichtiger Aspekt in der Auswahl von digital-optischen Anschlüssen erklärt sich durch das Vermeiden einer sogenannten „Brummschleife“, d.h. eine elektrisch leitende Verbindung zweier Geräte muß vermieden werden.
( mit Lichtwellenleiter - LWL- z.B. mit dem Anschluß-System Toslink )
In der Elektrotechnik ( Niedervolttechnik ) wird oft der „Negative“ Pol der Spannungsversorgung über das elektrisch leitende Gehäuse ( die sogenannte Masse )geführt. Das spart einerseits einen weiteren Kabelweg ( also Kupfer ) ein und ergibt eine mehr oder weniger wirksame (Ab-) Schirmung. Diese Schirmung soll die elektronische Schaltung vor elektromagnetischen, hochfrequenten und niederfrequenten Störeinflüssen je nach Ausführung der Schirmung schützen.
Üblicherweise besitzt jedes elektronische Gerät eine eigene Spannungsversorgung. Netzteile in elektronischen Geräten unterscheiden sich in der Art der Spannungsumformung, in der Höhe der Spannung, in der zur Verfügung gestellten Leistung, durch verschiedene Bauarten und unterschiedliche Bauteil-Tolleranzen entstehen somit verschiedenste Masse-Potentiale.
Werden solche Geräte durch elektrisch leitende Kabel verbunden, kommt es zu einem Ausgleich der verschiedenen Masse-Potentiale. Ein negatives Ergebnis der Verbindung von TV-Geräten oder PC-Komponenten mit Audio-Komponenten ist oft eine hörbare Beeinträchtigung von Audio-Signalen - ein tieffrequentes Brummen.( auch Brummschleife oder Masseschleife genannt )
Hierfür verantwortlich zu machen ist eine elektrisch leitende Verbindung. In der HiFi-Technik ist das in der Regel ein Koaxialkabel und dessen Schirmung.
Vermeidung u. Reduzierung dieser Störgeräusche Ansätze
!! Der einfache Weg !!
Einsatz einer optischen Signal- / Datenübertragung mit Lichtwellenleiter
- Glasfaser als Trägermaterial
( Einsatz einer Datenübertragung ohne elektrisch leitende Verbindungen )
aufwendige Wege
Einsatz einer Galvanischen Trennung - mit einem Ground-Isolator
(Massetrennung )
+ die elektrische Verbindung der Schirmung wird umgangen
- aber Leistungs- & und Klangverlust(geringere Dynamik)
- Verwendung von ( hochwertigen ) symmetrischen Verbindungen
( „PLUS“ „MINUS“ „Masse“)
+ Trennung der Schirmung an einer „Seite“ des Kabels möglich
[bei Koaxialkabel unsinnig weil eine Ader zerstört wird und
anschließend dieses Kabel wertlos ist ]
- sehr große Anschlüsse
- Profibereich
- Einsatz einer zentralen Spannungsversorgung für alle miteinander
verbundenen Geräte
Nachtrag
Bitte nicht verwechseln mit Netzbrummen - die Einstreuung der Netzfrequenz 50 Hz ( EU ) oder 60 Hz ( US ) in den Audio-Signalweg das ist üblicherweise auf eine nicht ausreichende Entstörung oder(Ab-)Schirmung zurückzuführen ist.
- End - !! Update !!
Einige Vorbetrachtungen
Die traditionelle Ton-Übertragung ist ein unkomprimiertes Signal, es wird in Stereo übertragen.
Wenn du CMSS ( Creative Multi Speaker Surround simulierten Surround Sound ) aus deiner Stereo-Musik erzeugen willst oder der Sprach-Test abgerufen wird ( nur über den Center ) ist der digitale Anschluß ( optisch & koaxial ) unbrauchbar, denn es würden nur die Lautsprecher Front-Rechts und Front-Links angesprochen !! Es wird ein anderer Anschluß benötigt, der die Kanäle einzeln ansteuert.
Für das Format 5.1 ist das die Verbindung über die drei 3,5 mm Klinken-Stecker ( 3 mal 2 Kanäle ) mit der folgenden
Kanalzuweisung 5.1
Front R / Front L + Rear R + Rear L + Subwoofer / Center
Mehrkanalton in Filmen - DolbyDigital (AC3 / DD) oder DTS
Filme auf DVD verwenden häufig ein kodiertes Mehrkanal-Audiosignal, in der Form DolbyDigital ( AC3 / DD ) oder DTS. Bei dem gebräuchlichsten Format 5.1 werden 6 Signale ( 3 mal 2 Kanäle ) in einem digitalen Datenstrom zusammengefaßt und komprimiert = das Kodieren.
Nach der Übertragung des Signals muß aus diesem Datenstrom ein Decoder die entsprechenden Töne trennen und jedem Kanal zuordnen = das Dekodieren.
Drei Varianten der Decodierung sind möglich.
(1) - AC3 / DTS Signal wird zu einem externen Decoder geführt
Genau hier wird der optische / koaxiale Anschluß genutzt. Um diese Variante nutzen zu können, mußt du ein digitales Lautsprecher-Set oder einen Digital-Decoder ( z.B: Digital-Receiver ) besitzen, der die Dekodierung des gewünschten Formats ( DD, AC3, DTS) übernimmt. Für jedes Digital-Format benötigt man einen entsprechenden Decoder – das Handbuch weiß hier oft mehr – welches Format von welchem Gerät dekodiert werden kann !!
Wähle in deiner DVD-Software den zur digitalen Datenübertragung gewünschten Anschluß "S-PDIF"( Koaxial ) oder "Optisch" als Audio-Ausgang.
In den Soundkarten-Einstellungen muß die Option "S-PDIF-Durchschleifen" ( "SPDIF Pass-through" ) eingestellt werden.
Dadurch wird das Audio-Signal von der DVD in digitaler ( komprimierter ) Form direkt an die Digital-Ausgänge der Soundkarte weitergeleitet. Anschließend kann ein angeschlossener externer Decoder z.B. im digitalen Lautsprecher-System oder im Digital-Receiver die Decodierung übernehmen und es entsteht ein „Räumliches Klangbild“.
Bitte merken:
Daß ist der einzige Weg 5.1 Signale ( digital ) über ein koaxiales bzw. optisches Kabel zu übertragen.
(2) - AC3 / DTS mit der Soundkarte decodieren
Diese Variante ist zu verwenden, wenn du keinen externen Decoder / Receiver verwenden willst.
In der DVD-Software wird "S-PDIF" als Audio-Ausgang gewählt und es muß zwingend in den Optionen der Soundkarte "S-PDIF-Durchschleifen" ( "SPDIF Pass-through" ) deaktiviert werden.
Die DVD-Software wird jetzt das ( digitale ) komprimierte Audio-Signal an deine Soundkarte senden und dann werden dort die digitalen Daten decodiert. Die Soundkarte gibt dann die 6 Audio-Kanäle ( bei 5.1 ) über ihre drei analogen Anschlüsse aus ( 3 mal 3,5 mm Klinke ) mit folgender
Kanalzuweisung 5.1
Front R / Front L + Rear R + Rear L + Subwoofer / Center
Es wird in diesem Beispiel also ein 5.1-Lautsprecher-System benötigt, mit der analogen Anschluß-Option von drei Klinken-Steckern.
( also 3 x 2 Kanäle = 3 mal 3,5 mm Klinke )
- die Einspeisung eines digitalen Signals über DigitalDIN, ist mit dem optionalen digitalen E/A-Modulbei möglich ***
- wird hier ein optisches / koaxiales Kabel verwendest, hörst du nur schwache Töne der Front-Lautsprecher R + L
*** Bei Karten der SB073X-Serie verfügt diese Buchse nicht über die Digital-In-Funktion !! zur Unterstützung des digitalen E/A-Moduls )
[ mehr unten ]
(3) - AC3 / DTS mit einer Software decodieren
Wenn deine Soundkarte kein DolbyDigital unterstützt
( wie die SB Live! 24-bit ) und auch kein digitales Lautsprecher-System vorhanden ist, kannst du Raumklang
(Surrsound-Sound ) aus DV-Filmen auch über eine AC3 / DTS fähige Software erzeugen.
Gratis-DVD-Software-Versionen unterstützen diese Funktion häufig nicht, du benötigst dann eine Software-Voll-Version.
Wähle die gewünschte digitale Audio-Tonspur „DolbyDigital“ oder „DTS“, im Audio-Menü einer DVD.
Dann stelle sicher, das in den Soundkarten-Optionen "S-PDIF-Durchschleifen"
( "SPDIF Pass-through" ) ausgeschaltet ist.
Wie unter (2) mußt du deine Lautsprecher mit den drei analogen Kabeln anschließen und nicht optisch oder koaxial !! ( 3 mal 3,5 Klinke )
Kanalzuweisung 5.1
Front R / Front L + Rear R + Rear L + Subwoofer / Center
Generell sind bei zuvor genannten Varianten (1) – (3) auch andere mehrkanalige
Wiedergabeformate möglich.
In Abhängigkeit von der Ausstattung der Quelle also von der DVD. der CD. der TV-Karte, dem Game usw. sind andere Formate z.B. 2.0 / 2.1 / 4.0 / 4.1 / 5.1 / 7.1-Kanal Wiedergabe möglich.
PC Spiele
PC Spiele nutzen normalerweise Technologien wie EAX, die ihren eigenen Surround-Sound, ohne Verwendung von DolbyDigital erzeugen. Selbst wenn dein Lautsprecher-System einen DolbyDigital-Decoder besitzt, ist dieser für Games unbrauchbar. Denn die EAX Verarbeitung findet direkt auf der Soundkarte statt und die Ausgabe der 6 Kanäle ( 5.1 ) erfolgt über die analogen Ausgänge
( 3 mal 3,5 mm Klinke ) ( oder über DigitalDIN, wenn vorhanden *** ).
*** Bei Karten der SB073X-Serie verfügt diese Buchse nicht über die Digital-In-Funktion !! zur Unterstützung des digitalen E/A-Moduls ) [ mehr unten ]
Kanalzuweisung 5.1
Front R / Front L + Rear R + Rear L + Subwoofer / Center
Für Mehrkanalwiedergabe in Spielen benötigst du also Lautsprecher-Systeme mit analogen Anschlüssen oder einen Digital-Receiver mit analogem ( 5.1 ) Eingang.
Wenn du ein optisches / koaxiales Kabel verwendest, dann kannst du nur die vorderen Kanäle ( links / rechts ) hören.
!!! Notiz !!!
X-Box Spiele unterstützen DolbyDigital, wenn du deine X-Box mit einem DolbyDigital-Receiver oder einem digitalen Lautsprecher-System über optische Kabel verbindest, kannst du den vollen Surround Sound nutzen.
Die Sound Blaster Karten der SB073X-Serie bieten neben dem digitalen ( koaxial / extern ) Anschluß über den Anschluss Flexi-Jack auch noch einen weiteren Anschluß, direkt auf der Karte ( koaxial / intern )
Flexi-Jack - DigitalDIN
Wenn du kein digitales E/A-Modul ( Digital I/O-Modul ) benutzen kannst, ist es möglich mit einem Klinke-Chinch Adapter ( RCA-Adapter ), ein digitales Lautsprecher-System oder einen Digital-Receiver digital ( koaxial ) über den Flexi-Jack-Ausgang der Soundkarte zu verbinden. Alle MiniDin bzw. 3,5 mm Klinken-Stecker können in der Mono- oder auch in der Stereo-Ausführung verwendet werden, denn der mittlere / vordere Pin des 3,5 mm Klinken-Steckers überträgt das AC3 / DTS Signal. Dazu benötigt man eine der folgenden Verbindungen
3,5 mm Klinke ( Mini DIN ) auf Chinch - Adapter ( RCA-Adapter )
für den S-PDIF-Anschluß( koaxial ) an Lautsprecher-Systeme mit digitalem Eingang bzw. Digital-Receiver kann man folgende Varianten verwenden
- Klinke-Mono - Chinch-Stecker ( Stecker –Stecker ) ( Favorit !! )
- Klinke-Mono auf Chinch-Mono ( Stecker - Kupplung ) + Chinch-Verbindungkabel
( Stecker - Stecker )
- Klinke-Stereo auf Chinch-Mono ( Stecker - Kupplung ) + Chinch-Verbindungkabel
( Stecker - Stecker )
Das digitale E/A-Modul ( Digital I/O – Modul )
Die Verwendung von optionalem Zubehör Digitales E/A-Modul ( Digital I/O-Modul ) bietet die Möglichkeit der direkten Verwendung eines S-PDIF Verbindungskabels und stellt zusätzlich zum koaxialen Anschluß einen optischen Anschluß ( Toslink ) bereit. Die optische Verbindung kann wie oben beschrieben zur Vermeidung einer Brummschleife hilfreich sein.
Des weiteren wird ( abhängig von der Ausstattung der Soundkarte *** ) ein digitaler Eingang über das E/A-Modul bereitgestellt, der Eingang ist ebenso wie der Ausgang in optischer ( Toslink ) und koaxialer ( S-PDIF ) Bauform ausgeführt.
Achtung !!
( *** Bei Karten der SB073X-Serie verfügt diese Buchse nicht über die Digital-In-Funktion !! zur Unterstützung des digitalen E/A-Moduls )
interner S-PDIF E/A-Anschluss ( für Geräte der SB073X-Serie )
zum Anschluß einer Decoderkarte oder externer Decoder bzw. Lautsprechersysteme mit digitalem Eingang ist ein entsprechender Adapter erforderlich
Bei einigen Modellen ist eine Dekoderkarte im Lieferumfang enthalten bzw. in einigen Regionen als Zubehör erhältlich
Front Panel-Sockel (für Geräte der SB073X-Serie)
2 x 5-poliger Front Panel-Sockel nur für Verbindungen mit einem Intel HD Front Panel Audio-Standardsockel (nur Geräte der SB073X-Serie) Intel Front Panel Audio-Kabels (separat erhältlich)
Anschlusskompatibilität
Ausschließlich Intel HD Front Panel Audio-Standard
Nicht kompatibel mit AC97 oder Intel-kompatiblem HD Front Panel Audio
Einschränkungen
Wenn neben den hinteren Mikrofonen auch Frontmikrofone angeschlossen sind, werden die hinteren Mikrofone automatisch deaktiviert.
Sound Blaster X-Fi E/A-Konsole
Auf der Rückseite Ihrer X-Fi-E/A-Konsole* befindet sich eine sogenannte DIN-Buchse. Um die Funktionen für eine integrierte Lautsprechersteuerung zu nutzen, können Sie an diese Buchse ausgewählte analoge Creative-Lautsprechersysteme anschließen, die über eine Kabelfernbedienung oder eine Audiokonsole verfügen.
So können Sie beispielsweise über den Master-Lautstärkeregler Ihrer X-Fi-E/A-Konsole die Lautstärke der Lautsprecher regeln oder die Lautsprecher stummschalten.
-eof-

Digitally Connecting Soundblaster audigy 2 to sonydav s550 home theatre sys

Hi, I have a Soundblaster audigy 2 im not sure which model but it has a pink digital out audio socket on the back of it. My sony system has a digital optical in socket on it. I am having problems connecting them. I brought the following
http://www.maplin.co.uk/Module.aspx?...gital&doy=26m5
as it has a miniplug adaptor which i thought I could use on one end to connect to my soundcard digital output and connect the other end to my home theatre system. Did I get the wrong wire? If so what wire will I need to connect them, will miniplug not fit on the soundblaster digital out, what does? I have messed around with the control panels with no luck. Anyone have any ideas, by the way Im new to this. Thanks in advance

Hello all,
I am having a similar issue. I would like to connect my Audigy 2ZS to a Sony Reciever (STR DE-898) preferably via the digital out. The sound card and reciever are 25 feet apart.
I have read that the digital out on the Audigy 2ZS is specifically for creative lab speakers, and that if you connect it to a normal reciever that it may damage the reciever is this true?
Second, the other option that I have is to buy the 7. adaptor and connect RCA extension cables to the reciever.
The last option is to connect it to the regular headphone jack out, and use an extension cable to connect to the reciever (This is what I am currently using), but the sound quality is terrible.
Please help, I read the recent post on digital out ,which helped some, but still the question remains... if you connect the digital out on the Audigy 2ZS to a Sony receiver will this damage the receiver?Message Edited by asharabi98 on 05-27-2006 0:38 AMMessage Edited by asharabi98 on 05-27-2006 0:39 AM

Digital Connection with Audigy 4 and DTS5

Hallo Everybody
I have the same Problem with the nice man in this post. (Felix2)
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=46632&vie w=by_date_ascending&page=
Exactly same problems! I emaild the Support and they replied me just trash.
So my base problem and thats in the linked thread above is to get a standard audigy 4 not a pro! optical connected to the dts 5500 er Station.
Please do not tell something of 5channel sound and ac3 and ac3 and ac3 its useless.
Please do not ask me about my system config, all works fine, the audigy4 works fine, my dts works fine and the speaker too. (Ive testet it with the 3 pole minijack connecters of my audigy 4).
So all works, but the opticalDigital connection not. (And i dont want to get 5. sound, i just want to get some sound, at the moment no sound comes out)
se give a statement why optical/digital connections not work on your products.
-Please give a statement why this is that difficult/confused to connect.
And a big bravo to Felix2. I wouldn't stay that cool like you if I get some horrible and wrong answers, especially of a "professional". Maybe you have a solution do get the DTS 5500 and audigy 4 get optical connected?
Greetings
Lex

Lex,
The information I gave Felix2 is not "horrible" or wrong, they are the truth. There is no need to start attacking again, if you are not clear on the information I gave in his thread, ask for more clarification, but do not attack.
If you are having problems getting it set up, it's best to provide some detail on what settings you have changed, how everything is configured, and someone will probably be able to help you.
The start of your post isn't very clear, do you have a standard Audigy 4 or an Audigy 4 Pro? The Audigy 4 Pro does have an optical output on the external dri'vebay, the standard Audigy 4 (just a card) does not have an optical output. You would need to connect through a coaxial input (minijack to RCA, then RCA-RCA).
Cat

Connecting HP w1907v Monitor speakers to HP Pavilion a6430.uk

I cannot get the correct speaker connection from the monitor to the tower and therefore have no sound available to me.
Can anybody help, please?
Peter2508

1) What video cable are you using from the computer to the monitor?
If it's an HDMI cable then the sound should go through that cable.
In this case there's no need to have the green audio cable from lcd to monitor connected, only the HDMI (black).
If the HDMI cable is used then make sure that the "Realtek HDMI output" is the default playback device.
You can check this by rightclicking on the white speakers on the bottom right corner of your screen next to the time and select Playback Devices.
Make sure the the Realtek HDMI output has a green checkmark. If it does then it should be fine, but if it doesn't, rightclick on it and select "set as default device".
Be sure to disconnect the audio cabel with the green color at the end from the lcd if you're going to the HDMI cable.
2) If you're using a VGA (blue)or DVI (white) cable for video then you must plug in the thin audio cable that came with your monitor to get sound.
The cable is green at one or both ends and goes in the back of the lcd and in the back of the computer in the round "doughnut shaped" color coated port. That's for front audio out.
It won't work in any of the other ports.
NOTE: You can also connect the audio cable to the front of the pc in the headphone jack instead if you want.
If the green audio cable is used then you have to make sure that"Speakers" is the default playback device in the sound options.
You can check this by rightclicking on the white speakers on the bottom right corner of your screen next to the time and select Playback Devices.
Make sure the the Speakers has a green checkmark. If it does then it should be fine, but if it doesn't, rightclick on it and select "set as default device".
Hope this helps and sorry for the long post.

Connecting TV and Computer Speakers at the same t

Hi,
I have a SB Li've Value and I wanted to connect my regular computer speakers as well as my TV to it.
I am using a mono plug to hook my computer speakers and my TV currently. Whenever I want output on my TV I have to unhook my computer speakers from the soundcard and plug in the mono plug from the TV.
Is there any possible that I do not have to do that and I can get output on both using the mono plugs.
Please help me out as I have looked al over the place and I cannot find an answer to this problem.

Get an /8" stereo Y splitter (single male, split side females)

Cable to ((Digitally)) connect iPod to Hi-Fi?

Here's the problem: Our back deck is rather old and tends to move abit as people walk across it. When the iPod is in it's cradle in the Hi-Fi, it tends to wiggle quite a bit. So, I'm wondering if I can ((Digitally)) connect the iPod - via a Dock connector - to the the toslink input jack on the back of the Hi-Fi. This would allow me to simply lie the iPod down on top of the Hi-Fi so that I don't have to worry about it toppling off. I'd prefer doing this digitally via the dock connector rather than simply using headphone jack as the output. Why? I'm a bit of an audiophile-neurotic and want to preserve the signal as much as possible. I guess what I'd need is a Dock connector - to - toslink connector cable, but I my Apple Store search turned up nothing.

Hello Syd,
As far as I know, the iPod does not carry any digital signal output with both the headphone jack and dock connector.
Therefore, at the moment you cannot find any iPod dock connector with a digital optical output.
Hope the next generation of iPod will include the digital output as well.
However, you can buy a Airport Express, links it with your computer via WiFi, then you can use a digital cable with both ends of mini-jack digital to connect AirPort express with your iPod HiFi. But it will loss all the remote function.
I have not tried it myself, therefore I am not sure about the sound quality in this way.
By the way, I have bought a GriffinXpressCable (for Airport Express to HiFi), and I will try to have a test later on.

Static / Bad Connection for External Bose Speakers?

Hello Everyone;
I recently bought a new 24" iMac and bought a set of Bose Companion speakers to go with it. I've plugged them into the headphones jack using the cable provided by Bose, but my sound quality is really bad. Theres a lot of static in the music, and by moving the 1/8' male connector that plugs into my iMac around or touching it while music is playing causes more static or sound failure - making me think it may be the connection at the computer. On the other hand, I'm not quite sure if the cable I'm using is an "optical digital audio out port" as described in the Mac manual. I haven't seen an optical digital 1/8" cable, so this is making me think the cable is the problem. The speakers run spdif out to 1/8".
So before I take my mac to have it looked at, does anyone have any ideas as to what I'm doing wrong, or should be doing and or using differently? Any help would be much appreciated.
Thanks;
Steve Masten
Message was edited by: stevemasten

Hi Steve,
I have exactly the same problem with my new iMac and my Bose Companion speakers (the ones with the 2 small cubes and a sub). The Bose speakers do not use a digital audio connection - so using Toslink would not be the answer.
I double-checked the connection on the back of the iMac and found that I was able to push the plug in a little bit more (it sort of clicked into place) - and that definitely helped some. As long as nobody touches it, it runs static-free....but even the slightest touch on the cable (or even the iMac sometimes) results in horrible static.
I'm considering trying another set of speakers because of this issue. I'm calling Bose tech support tomorrow because of this issue to see if they have any suggestions. I'll post back if I get any good info from them.
-RJ

Digital connection to 5.1 speakers : output on the rear of the ca

Similar Messages

Maybe you are looking for