DLNA Media Server is not showing on diffrent Vlans
Hi all,
i have a media Server in one Vlan now i want to access it from other Vlans as well. for DLNA i configure Multicast and PIM Spare mode with rp address on Cisco 4500x L3 switch and enable IGMP snooping on all my Layer 2 switches but still not able to show my DLNA in other Vlans
DLNA in Vlan2
want to show in it in Vlan3 and Vlan4
here is my L3 Switch configuration foe PIM
ip routing
ip multicast-routing
int vlan 2
ip add 192.168.2.1 255.255.255.0
ip pim sparse-mode
int vlan 3
ip add 192.168.3.1 255.255.255.0
ip pim sparse-mode
int vlan 4
ip add 192.168.4.1 255.255.255.0
ip pim sparse-mode
ip pim rp-address 192.168.2.1
sh ip mroute 239.255.255.250
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 239.255.255.250), 16:39:10/00:02:57, RP 192.168.2.1, flags: SJC
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Vlan2, Forward/Sparse, 00:27:03/00:02:56
Vlan3, Forward/Sparse, 02:08:20/00:02:56
Vlan4, Forward/Sparse, 12:20:31/00:02:57
Similar Messages
-
EA6500 DLNA media server MP3 not shown
Hi!
I have recently bought Linksys EA6500 router and attached a USB drive with some media (4000+ MP3 files, 7000+ photos, and 1000+videos). Everything works smoothly, even from Nexus 4 on wireless, but none of the MP3 files are showing up! Are there any known limitations in Twonky server (which this device apparently uses) in terms of naming files, subdirectory structure, anything? I tried rescanning the drive, although didn't try rebuilding database...
Any ideas?
Solved!
Go to Solution.Hi,
Yes. There's a known limitation with Twonky Media Server that's built-in with your router: "maxfile-8000" - the license with Twonky limits the # of files to be scanned to 8000. This issue had been raised before and some acceptable reason is the "amount of cpu and ram need to deal with the db in memory" - of course, these routers have way much lower hardware specs, even compared to a smartphone running on Android 2.3.6 OS.
Here's the thread that was raised before:
http://community.linksys.com/t5/Wireless-Routers/E4200-v2-Twonky-Media-Server-Issue-Default-quot-max...
Here are the links from Twonky Community Forum:
http://community.twonky.com/twonky/topics/limit_8000_files
http://community.twonky.com/twonky/topics/twonky_media_server_issue_with_cisco_ea4500_router_and_wd_...
http://community.twonky.com/twonky/topics/cisco_e4200_default_maxitems_is_8000
Hope this helps.
If everyone needs to believe in something, I believe I'll have another beer.. -
'[FAQ] Twonky DLNA Media Server Setup & Use
Some Frequently Asked Questions Regarding Twonky, And Some Answers The MyCloud includes a Twonky DLNA Media Server. Sadly it doesn't seem very well integrated into the MyCloud, and the two fight for supremacy. I've spent a long time trying to understand how it works, and reading the forum, I see many other people also have trouble with it. So I thought that, rather than trying to answer these questions individually, I'd try to write an FAQ covering the things I've found, and the problems I or others have encountered, and the solutions.
I'm not a member of WD staff. I'm not a MyCloud, Twonky or Linux expert (but I'm moderately competent). But I am stubborn, and determined to find out how to make the thing work the way I want it to. If more expert users find fault in this FAQ, or have other insights to offer, then feel free to post comments. I'll edit this first post and make corrections and add any FAQ&A that are added.
Where I am unsure of something, I'll enclose it in [brackets]. Feel free to investigate and confirm or disprove my observations... Where I mention control settings, I use a | to indicate a level of hierarchy in the menu system. This is to distinguish control settings and file system paths.
Ideally, we'd shame WD into doing a better job of integrating Twonky into the MyCloud, so it's not such a struggle, and doesn't require Linux administrator-level skills to make it work properly. Starting the Media Server and setting up a Media LibraryQ. What is a Media Server?
Q. How do I start the Twonky Server?
Q. How do I control the Twonky server properly?
Q. Where should I put my media so Twonky finds it?
Q. Why doesn't Twonky find my media?
Q. Can I stop Twonky searching in certain folders in my media storage folders?
Q. What are the 'Shared Media' folders for?
Q. Why can people using DLNA clients see media in my private share?
Q. How do I control when Twonky rescans the media store? Optimising operation of the Media Server
Q: How does the Twonky service work on the MyCloud?
Q. Where is the Twonky database stored?
Q. Where are the Twonky settings stored?
Q. What do all the settings in Twonky's configuration file do?
Q. How do I clear Twonky's database and start again?
Q. Where can I find debug log files for Twonky?
Q. How do I stop MyCloud breaking the Twonky Server?
Q. Can I change to location of the 'Shared Media' folders?
Q. Why does setting a Twonky access control password prevent the MyCloud from sleeping?
Q. Can I replace Twonky with another Media Server?
Optimising behaviour for Media Clients
Q. Why does my media player not show the right track information?
Q. How can I get Twonky to provide full size artwork to clients, rather than crude thumbnails?
Q. How can I change the media 'views' I see in my DLNA client?
Q. Can I add my own category to the Music/Photos/Videos categories?
Some Prerequisites
You'll need to know how to use the WD Dashboard browser interface to control the MyCloud:
http://wdc.custhelp.com/app/answers/detail/a_id/10420
You'll need to know how to use the Twonky UI browser interface to control Twonky:
http://wdc.custhelp.com/app/answers/detail/a_id/3299
You'll need to know how to use SSH to log in as root to the MyCloud:
http://wdc.custhelp.com/app/answers/detail/a_id/10435
Note the big warning signs about warranty. IMHO, it's a bit off to make dire threats like this when you often NEED to SSH login to get the advertised services to work properly.
Some Unix experience will help, but I'll try to explain all the commands you'll need. Experience with a Unix text editor such as vi or nano is assumed.Q. How does the Twonky service work on the MyCloud?
A: [Twonky is installed as a Linux service. Like other such services, there is a service control file in the /etc/init.d directory]:
/etc/init.d/twonky
This is called when the twonky service is invoked, and there are a number of options for the control of Twonky using an SSH root login:
service twonky start
service twonky stop
service twonky restart
service twonky status If you execute the start or stop commands with Media Streaming turned on in the Dashboard, you are likely to confuse the Dashboard; you may get an 'Error 400162'.
'start' calls writeTwonkyContentDir.sh, which, as we'll see later (Q: How do I stop MyCloud breaking the Twonky Server?), reads the /etc/contentdir file and modifies the twonkyserver.ini file to set the media search paths and types, and then starts the Twonky server.
[It is assumed that the MyCloud Dashboard uses these Twonky service calls to start and stop the Twonky server]. Q. Where is the Twonky database stored?
A: Since Twonky is a service running on MyCloud, it is not visible in the shared space, so you have to log in via SSH, and navigate around the MyCloud's Linux file system.
Once you have logged in, use the cd command to change directory to Twonky's area:
cd /CacheVolume/twonkymedia Now see what's there with a directory list:
ls -l Q. Where are the Twonky settings stored?
A: One of the files listed above is the Twonky configuration file:
twonkyserver.ini This file contains all the settings that control how Twonky works.
Now, this is where some of the fighting occurs, because both MyCloud and Twonky can modify this file...
When you are happy that Twonky is working correctly, I'd recommend making a copy of the file in your Public area, where it won't be mangled by MyCloud firmware upgrades or restarts. For instance:
cp /CacheVolume/twonkymedia/twonkyserver.ini /shares/Public/twonkyserver.ini
If things go wrong, you can reinstate this file by swapping the source and destination. Q. What do all the settings in Twonky's configuration file do?A: [Most of them are provided with comments that explain their purpose].
[There are some 'magic numbers' embedded in the configuration file that seem to cause problems, and I don't know what changes those; I suspect that a firmware upgrade does it. If anyone can monitor these values before and after a MyCloud firmware upgrade and report any changes, I'd be obliged:
# UserID Please Do NOT change it manually
userid=<redacted>
# twonky info for Media Feeds Please Do NOT change it manually
twonkyinfo=<redacted>] Q. How do I clear Twonky's database and start again?
A: If Twonky doesn't seem to be behaving correctly (not finding media correctly, or partially, or finding unwanted media), then it may be useful to clean up the database. There are a number of escalating actions you can take. Starting with the mildest, and increasing in severity, these are as follows:
1. Initiate a library rescan, using either Settings|Media|DLNA Database|Rescan in the Dashboard, or Settings|Advanced|Server Maintenance|Rescan Content Folders in the Twonky UI.
2, Initiate a library rebuild, using either Settings|Media|DLNA Database|Rebuild in the Dashboard, or Settings|Advanced|Server Maintenance|Restart Server in the Twonky UI.
3. Finally, you can completely clear out Twonky's working area. [This can be useful if you notice the '[Error] - LOG_SYSTEM: Error: 2 No such file or directory' report in the Twonky logfile. I don't know what causes this error, or whether it has serious consquences, but I have found it to be associated with periods of diffcult behaviour.] Turn Twonky off using the Settings|Media|DLNA Media Server|Media Streaming control in the Dashboard. Then SSH root login, and hide the entire Twonky working area:cd /CacheVolumemv twonkymedia twonkymedia_bak Restart the Twonky Server using the Dashboard; it will re-create Twonky's working area with a clean version with default settings. You can then use the Twonky UI to put your settings back in place. You might try doing this one-by-one, saving the settings and restarting the Twonky server from the Twonky UI each time, then checking the logfile after the Twonky UI has re-appeared. Once you're happy with the operation of the clean startup, you can delete the old Twonky working area:
rm -f -R /CacheVolume/twonkymedia_bak
The -f -R flags mean 'delete EVERYTHING from here down... yes, I mean it'. nb. it will only delete the Twonky database; it won't delete any of your media. But do be careful that you type the command in correctly; rm -f -R is a powerful command (-f means force, -R means recursive), and could do a lot of damage if you get it wrong...
Q. Where can I find debug log files for Twonky?
A: You can enable activity logging using the Settings|Advanced|Logging control in the Twonky UI. You can also open the logfile from there.
Alternatively, the logfile is stored in Twonky's area:
/CacheVolume/twonkymedia/twonkymedia-log.txt
There's also a MyCloud system logfile that records actions on the Twonky server, such as start and stop:
/CacheVolume/update.log Q. How do I stop MyCloud breaking the Twonky Server?
A: Firstly, go to the Settings|Firmware page in the Dashboard, and disable Auto Update: firmware upgrades completely destroy the /CacheVolume/twonkymedia area, and replace it with new, default version, so you'll be back to square one.
Secondly, we can stop the problem of Media Streaming restarts overwriting the Twonky UI settings. Using an SSH root login, enter the following commands:
cd /usr/local/sbin
mv writeTwonkyContentDir.sh writeTwonkyContentDir.sh.old
This disables the script that MyCloud calls when it starts Twonky, which overwrites your settings.
Another way of fixing the settings is to leave this script alone, but change the file it uses as the source of the settings. Admittedly, this will still override any changes made via the Twonky UI. The file is found here:
/etc/contentdir
Replace this with a single control line, with no line terminator, e.g.
+M|/Public/Music,+P|/Public/Pictures,+V|/Public/Videos This will select my earlier settings.
The format is a comma-separated list of shares and media search and aggregation control flags:
+ enable media searching on the share
- disable media searching on the share
A look for all media types
M look for music
P look for pictures
V look for videos
lower case letters enable aggregation of these media types.
The | terminates the media type string [you can search for multiple types in a share]. Q: How can I change the location of the 'Shared Media' folders?A: This brings us deep into the guts of the twonkyserver.ini file... There are a number of settings that control where Twonky stores uploaded files and 'servermanaged' media, [which are used for aggregation], and there is no control setting for them in the Twonky UI. To change the location of the folders we have to do an SSH root login and edit the twonkyserver.ini file. The lines in question are as follows:
uploadmusicdir=/shares/Public/Shared Music
uploadpicturedir=/shares/Public/Shared Pictures
uploadvideodir=/shares/Public/Shared Videos
servermanagedmusicdir=/shares/Public/Shared Music
servermanagedpicturedir=/shares/Public/Shared Pictures
servermanagedvideodir=/shares/Public/Shared Videos
You can change these locations to suit your desired file system. For instance, you could create a single 'Shared' folder in the Public area, with sub folders for the different media types, e.g.
uploadmusicdir=/shares/Public/Shared/Music
Or you could create a Shared sub folder within each of your main media folders, e.g.
uploadmusicdir=/shares/Public/Music/Shared
However, if you choose that option, you will need to stop Twonky searching there, by adding 'Shared' to the list of ignored directories discussed above. Q. Why does setting a Twonky access control password prevent the MyCloud from sleeping?
A: It has been reported that if a username and password are set using the Settings|Advanced|Secured Server Settings control in the Twonky UI, that the MyCloud then never sleeps. [It appears that the MyCloud continues to interrogate the drive in some way, hoping to get status of the Media Server from Twonky, but Twonky won't talk to it because it doesn't have the required permission.].
I don't think this is very important, since the MyCloud is mainly intended for home use, and the Twonky control UI isn't visible external to your local network, and all users on your local network must be trusted*, since you've given them the network access code, [and they have access to the Public area, and could wreak havoc there...] If you need to make your music library available to visitors who cannot be trusted, create a private share and put all your media under that, then enable media serving on that share, and get Twonky to search for media in that private share. DLNA ignores acces control, so DLNA clients will be able to see the media on your private share, but visitors will not have access to your private share via network file access. [However, if you feel that secured access to the Twonky UI is necessary, then I would suggest that you disable the Twonky server using the Settings|Media|Media Streaming conrol, then SSH login as root, and start Twonky using the command:service twonky start You won't get the media scan status in the Dashboard, but the Twonky Server and UI will be running.]
* Breaches of this trust should be punished in an appropriate manner...
Q. Can I replace Twonky with another Media Server?A: Yes; forum users hvalentim and Nazar78 have posted good threads about this:MiniDLNA for V3 firmwareMiniDLNA for V4 firmware Kudos to them :-) -
EA6900 DLNA Media Server update intervall
Hi everyone,
I have the problem, that the media server does not update within the setted intervall. I set it up to scan the folders every 2 hours, but i updates the folder only every day or even less.
For example - I made this screenshot today, October 16 - 10 a.m. (I am writing from Vietnam - so don´t wonder about the dates)
So i played around withe the settings - 6hr/12hrs - no change.
We use the DLNA Server for Samsung Smart TVs - so it is important, that it will update regulary.
Anyone has an idea, what could be the problem?already did when I bought the router - so firmware should be the newest.
Should I try to downgrade to an older firmware?
I shared the whole drive in the settings. -
The report I published on the SQL server report server is not showing in the application we use to retrieve reports. My cell phone number is {removed}
Thanks.Hello Roger Tenn,
Thank you for posting in the TechNet Forum.
As this issue is related to SQL server report server, to receive better report, it is recommended to ask in the SQL server forum.
https://social.technet.microsoft.com/Forums/en-US/home?category=sqlserver
The professionals here will be glad to help you.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support -
I'm using CS6 Extended. My OS is "Windows 7 home premium.
Can no longer load video files into CS6 for edited I keep getting error message:
'Could not complete your request because the DynamicLink Media Server is not available.'
Don't know what this means. Until just now I was able to load videos without any problems. Now I'm getting this message. Any thoughts?Hi Mylenium,
upfront:
I hope I won't be marked as spam now, since I am posting on a few relevant discussions now to this topic.
However, I really would like to ask the people who have experienced this problem to see if they were able to solve it.
Now the real deal:
I posted a question in this discussionDynamicLink Media Server won't let me import video for video frames to layers anymore.
The linked discussion is a lot younger, which is why I posted there first.
I also put in information on the steps that I have tried and my computer specifications.
I am experiencing this problem for a while now and hope you and jones1351may be able to help out. -
Could not complete the video frames to layers command because the DynamicLink Media Server is not av
I have this problem, I have PS CS6 and when I click on File> Import> Video Frames to Layers.. Next, the window that says "Initializing Video Import" starting to load and always get stuck and that's what appears: "Could not complete the video frames to layers command because the DynamicLink Media Server is not available". That's with aaaall the videos.
PS: I've been trying with File> Open but that's what says "Could not complete your request because it is not the right kind of document"
Anybody know what happens to my photoshop? Thx!The relevant auxiliary service/ helper app is being blocked and thus not launching,. anything from permissions issues to security tools getting in teh way. Check your Task Manager/ Activity Monitor, turn off security stuff, run as admin.
Mylenium -
Adobe Media Player does not show day 5
On my computer, the Adobe Media Player does not show day 5. Shows days 1 through 4.
Also on Day 4, trying to view the video "Create States and How to bind them"
I get a "corrupt file" error when trying to watch using the Adobe Media Player...
Also will someone please give a clear statement how to do a download of the files so
we can watch them off line. This still isn't clear to me.
I don't know what Craig is talking about below: How does that relate to downloading the
files.
The new instructions and feed links are now live on the Flex in a Week video training home page:
http://www.adobe.com/devnet/flex/videotraining/
Please try them out!
Thanks,
Craig
Craig Goodman
Thanks so much
Fritz KleinThank you very much Craig for your help.
For some reason that section on Flash Builder in a Week;
+ Want to view Flex in a Week videos in offline mode?
was not displaying on my browser page. I re-installed java and it now seems to work all ok, and it along
with your advice addresses the issue.
Fritz -
DynamicLink Media Server is not available. I can't open any video file in Photoshop CC and when it does, Photoshop freezers and I can't do anything else. I'm using OS X 10.9.4-3.1 GHz Intel-16 GB DDR3. Any help please?
Indicas que no puedes abrir ningun archivo de video, se supone que has probado varios formatos, mp4, mov,..
Has actualizado el OSX a 10.9 ?, funcionaba antes? La versión de Photoshop es la CC, no la CC 2014?
En el menú de Ayuda>Actualizaciones, cual es el resultado, dice que esta al día?
Tienes abiertas otras aplicaciones?
Prueba a cerrar todo, espera media minuto y abre Photoshop a ver que ocurre.
(Estas utilizando un MacBook Pro?) -
Essbase server is not showing in the windows services (11.1.2.1)
Hi All,
Essbase server is not showing in the windows services 11.1.2.1. when I checked the processes from task manager it is there.
Regards,The windows service for essbase in 11.1.2.x is an OPMN service "Oracle Process Manager..."
Cheers
John
http://john-goodwin.blogspot.com/ -
Photoshop 2014 (fresh install) cant open a video because: …. the dynamiclink media server is not avalable – any idea how to fix this on os x 10.5.8 ?
i found the error!
little snitch on os x blocks something (i dont know what exact) of adobe in the background. i have no rule defined for adobe in little snitch, so everything of adobe can go out.
when i stop little snitch, everything works fine - photoshop opens videos without the medialink error, photoshop starts up in seconds and premiere starts without a quicktime error.
i report the problem also to objective developement to fix this!
mad -
Media Browser is not showing fiber optic server volumes.
Using Avid Unity fiber optic server I can edit with Premiere but the volumes are not showing in the Media Browser. Ethernet volumes are showing in the Media Browser.
Ideas? -
WRT350N Media Server does not serve music up to a Directv HR20
I have a Directv HR20. This device is a UPnP device that is capable of playing Music/Picutres on the TV/Stero system using a media server software. The intention of my purchase of the WRT350N router was to install a 500GB USB drive onto the router and use the media server software to supply music and photos onto the Dirctv HR20 DVR. This has not been an easy task. I can see the pictures and play the pictures without an issue. I contacted Linksys support via the Live chat and spoke with them explaining how the media server is suppose to supply the music as well and the Directv HR20 is ecpecting a LPCM trascoder to work. They assured me that they would pass this information up to the development team. This was almost a month ago and I have not heard back from them yet. I downloaded the beta version of the firmware and tried it, but it to did not work. Other media server software does in fact work like Nero 7 media server and Twonky media server software. I currently use the Nero 7 media server software on my PC to serve music and photos to the Dirctv HR20.
The Directv HR20 uses a WET54g currently to connect to the home network. I will need to update this to a "n" type of connection when a game adapter or bridge device is avliable for "n".
So now here I sit with an expensive USB drive and I cannot use it for the music side of the media server portion of the WRT350N.
Any help would be appreciated!
Message Edited by Spanky_Partain on 07-24-2007 07:35 AMIt is really hard to believe that Linksys is not interested in fixing this issue. The Directv equipment that is DLNA compliant to Doc 1.0 and the Samsung LN52A860 which is also DLNA compliant will NOT see the media server and take advantage of the USB storage device that has Music and Photos stored on them.
Come on Linksys by Cisco, get your firmware compliant to the standards the industry is following and STOP tyring to write your own!
Mark -
Media browser does not show photos
The media browser in iDvd & iWeb does not show the photos in my iPhoto library. It does show the tunes in my iTune library but not the photos in my iPhoto library. When I click photos in the browser, the browser says, "Open iPhoto2 or later or Aperature1.5 or later from your iPhoto or Aperature library in this list."
I have iPhoto6.0.6. When I made a DVD two months ago everything worked okay. I suspect that I am missing something very obvious, but to date it escapes me. Does anyone have some experience with this problem? Please help.One thing that you can try is the often used maintenance of deleting preferences and doing a permissions repair. To delete preferences, close iMovie and iPhoto and trash the files named com.apple.iMovie.plist and com.apple.iPhoto.plist found in User (the house icon)/Library/Preferences. Then restart your computer and do a permissions repair using the Disk Utility app found in HD/Applications/Utilities. In the left hand pane of the Disk Utility window select your hard drive icon and then click on repair permissions. Takes about 3 minutes to repair. Then relaunch iMovie and iPhoto and see if you still have the problem. Those applications will recreate the .plist files that you deleted.
However, this might be an iPhoto issue, and I would suggest that you post your question in the iPhoto forum as well.
Have you updated iPhoto recently? Have you made any manual changes to your iPhoto library? Do you use keywords? Is your iPhoto library stored on an external drive where possibly iMovie can't locate it?
It could be that you just need to rebuild your iPhoto library. You can do that by holding down the Option and Apple keys while launching iPhoto. Then chose the first 3 selections in the drop down menu. But be sure first to back up your iPhoto library to guard against power outages or other probs during the rebuild process. As I say, check with the iPhoto forum if deleting preferences and repairing permissions does not work.
See if anything in this thread helps:
http://discussions.apple.com/thread.jspa?messageID=8450454�
Message was edited by: Rich839 -
Server: Mail configuration of Server Admin not showing ANY Accounts
I have an LDAP directory for my accounts and in the Server Admin GUI, under the Mail configuration, I am not showing any accounts. Currently mail services not working and I have tried to reconstruct the db to no avail.
I the POP log im gettting ...
Aug 10 14:03:29 mail pop3[24233]: DBERROR: critical database situation
In the Mail Access log ...
Aug 10 14:04:56 mail lmtpunix[29548]: DBERROR: critical database situationHow about more info?
Did you ever have a working setup? Accounts?
How did you try to reconstruct?
Check /var/log/mailaccess.log and post some more info for a process number (number in square brackets)
Maybe you are looking for
-
when i log in to this web site it opens the game screen. when i then want to go to a different location in the game. it resets back to log in screen again. but it works ok on all other sites. == URL of affected sites == http://s3.travian.co.uk/dorf1.
-
Java.lang.SecurityException: Authentication denied: Boot identity not valid
Hi, When I try to start up the WebLogic server by running a startup script in the WebLogic server root directory, I am getting the following error: <Apr 23, 2003 1:15:11 PM EDT> <Critical> <WebLogicServer> <000364> <Server failed during initializatio
-
How do I get a link to change color after I use it.
<blockquote>Locking duplicate thread.<br> Please continue here: [[/questions/908525]]</blockquote> How do I get a link to change color after I use it. .
-
Hi Does somebody knows some user exit or BADI for add validations to FB02 when user changes some position data. I need to validate some header BKPF (Company, Currency) and detail BSEG (Posting Key, Account Bank) data when change the position. Does s
-
Debugging/Breakpoints in Flashbuilder 4
Hi, There seems to be a bug in Flashbuilder 4 whereby it doesn't recognise changes/additions made to AS code. This means that firstly it completely ignores new code and secondly that I cannot set breakpoints properly. For example it allows me to set