DMZ Issue
I'm using a RV320 and have a puzzling issue. I would like to provide DHCP for the DMZ network but I can't get it to work. I created a VLAN, assigned the DMZ to that subnet by giving it an address in that subnet, but it is not passing out addresses to the devices connected to the DMZ port. I'm stumped - does anyone know what I am missing?
Hi,
If you are using the option Enable DMZ from Network Menu. Overthere you have 2 options - to put a subnet or a range of IPs. But the 2 options require to put a public IP or IPs. Than on the DMZ port you plug the machine which will receive this trafic and you configure this machine with this same public IP.
This router do not support NAT on the DMZ zone - what I mean is that you cannot assign VLAN with DHCP to the DMZ zone. This feature is support only by SA500 and ISA500 from the small business range.
Similar Messages
-
SA 540 and DMZ Issue for Wireless Guest Access
I have hooked up a Wireless AP into the Optional Port setup as DMZ on the SA 540. My goal is to provide internet access to wireless guest users without giving them access to the entire LAN. The internet access for the wireless guest users is painfully slow. It takes 5 minutes to access Google. Has anybody else had issues with slowness. I am able to successfully ping websites and retrieve their IP address, but it won't connect to any websites via web browsers. Just to humor myself, I configured firewall rules to allow DMZ full access to the LAN and WAN. I am still having the same results. Any thoughts and suggestions?
Hi,
I'm not the one with the AP problem, I just have the same issue with the DMZ port. I think you have to forget about the whole AP issue here since the problem is with the DMZ port on the SA500.
I have my Web and Mail server set up on the DMZ port, I can ping and resolve Domain names to the outside world, but trying to reach anything with a browser takes foreeever. On, eg. www.apple.com I just get a few lines from their web page (so there is a connection) and then it halts to a stop (takes about 5 min).
I also tried to move my laptop to the DMZ, just to make sure there is no problem with the server, and it has the same issue.
To summarize, I have about 16 Mb connection on my LAN and on my DMZ i can't even load a full web page.
Firmware 1.0.39
BTW, when I upgraded the firmware it wiped my configuration, but it kept my firewall rules in place, even though they weren't shown in the Firewall table. e.g. I could still access my DMZ from my LAN. I had to hard reset the router from the hardware reset button on the router before that changed and the router was completely reset. -
DMZ issues in ASA 5505 Firewall
hi , i have asa 5505 firewall with ASA5505-UL-BUN-K9 license i have problem with DMZ. I am not able to create dmz. please suggest me what i need to do in order to be able to configure dmz. should i need to upgrade the license. please suggest.
Hi,
Is the currently licensed firewall something that you have had for sometime or is it a new purchase?
Just wondering as it would seem unreasonable to just have bought something and then having to get a new license. Just wondering if you can somehow avoid spending extra money if this is a new purchase that wasnt what you were actually looking for.
You can check this link for the differnent options the ASA5505 has
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80402e36.html
You can also check this link for all the available licensed options on the ASA5505
http://www.cisco.com/en/US/docs/security/asa/asa91/license/license_management/license.html#wp2124788
This link contains also information on the ASA models
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80285492.pdf
So essentially you would get 20 Vlan interfaces instead of 3 and also support for Trunking which would let you use a single physical link for several Vlans (if you wanted that is)
Hope this helps
- Jouni -
Error downloading the Application/Framework files: DMZ issues
We have the sync servlet outside the DMZ. Users can do a sync of the data using this but when they want to download the WAR file (The Framework or Application) it doesnt let them do it.
The workaround that our basis guy has come up with is to go the Table where the PATH of the WAR file is stored (you can see this path in the Webconsole) and changed the relative name to include the full http://... name. This works, however is there a way to specify the location of framework or application file when we upload it using the WebConsole to include the full path instead of the relative path?
Thanks in advanceThere is a field in the WebConsole where you can enter the domain name when uploading the war file.
When you click on "Upload Mobile Component", there is a text box named: "Domain in URL". Enter something like: company.com
In this way, the URL for app download will have a full qualified name.
Hope that helps.
Peter -
Hi,
i have a new asa 5512-x with interfaces configured. i did static nat for the dmz private address to translate to one of the addresses from my ISP. but i notice the following:
1. i cannot reach that server on the public ip address 197.211.36.36
2. with dynamic translation, my inside hosts can access the server in the dmz through its private IP 192.168.88.1
attached is the running config.Hi,
I don't think the ASA really has a concept of DMZ ports/interfaces other than on ASA5505 and maybe some special model of ASA. Maybe it was ASA V1000.
In the normal ASA5500 Series and ASA5500-X Series the only limitation you have is either the amount of physical ports of if you use Trunk interface then the maximum supported Vlan ID amount. The amount of DMZs you configure is only limited by those.
There is no configuration on the ASA that would define the port as some sort of DMZ port. Generally you would just configure the interfaces ACL so that connections could not be initiated from behind this interface to the internal network.
If you want to check the supported Vlan ID amount of the ASA you have you can check this document
http://www.cisco.com/c/dam/en/us/products/collateral/security/asa-5500-series-next-generation-firewalls/at_a_glance_c45-701635.pdf
Seems your ASA model supports 50 Vlan IDs. As an extreme example it would seem to me that you could configure a single Trunk interface with 50 subinterfaces and also use the remaining 5 physical interfaces for some purpose. Though that probably would not be the ideal setup but just an example.
- Jouni -
AnyConnect to ASA 5505 ver 8.4 unable to ping/access Inside network
My AnyConnect VPN connect to the ASA, however I cannot access my inside network hosts (tried Split Tunnel and it didn't work either). I plan to use a Split Tunnel configuration but I thought I would get this working before I implemented that configuration. My inside hosts are on a 10.0.1.0/24 network and 10.1.0.0/16 networks. My AnyConnect hosts are using 192.168.60.0/24 addresses.
I have seen other people that appeared to have similar posts but none of those solutions have worked for me. I have also tried several NAT and ACL configurations to allow traffic form my Inside network to the ANYConnect hosts and back, but apparently I did it incorrectly. I undestand that this ver 8.4 is supposed to be easier to perform NAT and such, but I now in the router IOS it was much simpler.
My configuration is included below.
Thank you in advance for your assistance.
Jerry
ASA Version 8.4(4)
hostname mxfw
domain-name moxiefl.com
enable password (removed)
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
switchport trunk allowed vlan 20,22
switchport mode trunk
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
interface Vlan1
nameif inside
security-level 100
ip address 10.0.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Vlan20
nameif dmz
security-level 50
ip address 172.26.20.1 255.255.255.0
interface Vlan22
nameif dmz2
security-level 50
ip address 172.26.22.1 255.255.255.0
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 208.67.222.222
name-server 208.67.220.220
domain-name moxiefl.com
same-security-traffic permit inter-interface
object network Generic_All_Network
subnet 0.0.0.0 0.0.0.0
object network INSIDE_Hosts
subnet 10.1.0.0 255.255.0.0
object network AnyConnect_Hosts
subnet 192.168.60.0 255.255.255.0
object network NETWORK_OBJ_192.168.60.0_26
subnet 192.168.60.0 255.255.255.192
object network DMZ_Network
subnet 172.26.20.0 255.255.255.0
object network DMZ2_Network
subnet 172.26.22.0 255.255.255.0
pager lines 24
mtu inside 1500
mtu outside 1500
mtu dmz 1500
mtu dmz2 1500
ip local pool VPN_POOL 192.168.60.20-192.168.60.40 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic Generic_All_Network interface
nat (inside,outside) source static INSIDE_Hosts INSIDE_Hosts destination static AnyConnect_Hosts AnyConnect_Hosts route-lookup
nat (inside,outside) source static any any destination static NETWORK_OBJ_192.168.60.0_26 NETWORK_OBJ_192.168.60.0_26 no-proxy-arp route-lookup
nat (dmz,outside) source dynamic Generic_All_Network interface
nat (dmz2,outside) source dynamic Generic_All_Network interface
route inside 10.1.0.0 255.255.0.0 10.0.1.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 10.0.0.0 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
fqdn anyconnect.moxiefl.com
subject-name CN=AnyConnect.moxiefl.com
keypair AnyConnect
proxy-ldc-issuer
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate 439a4452
3082026c 308201d5 a0030201 02020443 9a445230 0d06092a 864886f7 0d010105
05003048 311f301d 06035504 03131641 6e79436f 6e6e6563 742e6d6f 78696566
6c2e636f 6d312530 2306092a 864886f7 0d010902 1616616e 79636f6e 6e656374
2e6d6f78 6965666c 2e636f6d 301e170d 31333039 32373037 32353331 5a170d32
33303932 35303732 3533315a 3048311f 301d0603 55040313 16416e79 436f6e6e
6563742e 6d6f7869 65666c2e 636f6d31 25302306 092a8648 86f70d01 09021616
616e7963 6f6e6e65 63742e6d 6f786965 666c2e63 6f6d3081 9f300d06 092a8648
86f70d01 01010500 03818d00 30818902 8181009a d9f320ff e93d4fdd cb707a4c
b4664c47 6d2cc639 4dc45fed bfbc2150 7109fd81 5d6a5252 3d40dc43 696360d5
fbf92bcc 477d19b8 5301085c daf40de5 87d7e4aa f81b8d7f 8d364dfa 0a6f07d7
6a7c3e9b 56e69152 aa5492d8 e35537bd 567ccf29 7afbeae8 13da9936 9f890d76
1d56d11d da3d039a 0e714849 e6841ff2 5483b102 03010001 a3633061 300f0603
551d1301 01ff0405 30030101 ff300e06 03551d0f 0101ff04 04030201 86301f06
03551d23 04183016 80142f27 7096c4c5 e396e691 e07ef737 af61b71f 64f1301d
0603551d 0e041604 142f2770 96c4c5e3 96e691e0 7ef737af 61b71f64 f1300d06
092a8648 86f70d01 01050500 03818100 8f777196 bbe6a5e4 8af9eb9a 514a8348
5e62d6cd 47257243 e430a758 2b367543 065d4ceb 582bf666 08ff7be1 f89287a2
ac527824 b11c2048 7fd2b50d 35ca3902 6aa00675 e4df7859 f3590596 b1d52426
1e97a52c 4e77f4b0 226dec09 713f7ba9 80bdf7bb b52a7da2 4a68b91b 455cabba
0cc4c6f3 f244f7d9 0a6e32fb 31ce7e35
quit
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev2 remote-access trustpoint ASDM_TrustPoint0
telnet timeout 5
ssh 10.0.0.0 255.0.0.0 inside
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd dns 208.67.222.222 208.67.220.220
dhcpd auto_config outside
dhcpd address 10.0.1.20-10.0.1.40 inside
dhcpd dns 208.67.222.222 208.67.220.220 interface inside
dhcpd enable inside
dhcpd address 172.26.20.21-172.26.20.60 dmz
dhcpd dns 208.67.222.222 208.67.220.220 interface dmz
dhcpd enable dmz
dhcpd address 172.26.22.21-172.26.22.200 dmz2
dhcpd dns 208.67.222.222 208.67.220.220 interface dmz2
dhcpd enable dmz2
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint0 outside
webvpn
enable outside
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-3.0.2052-k9.pkg 1
anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_AnyConnect internal
group-policy GroupPolicy_AnyConnect attributes
wins-server none
dns-server value 208.67.222.222 208.67.220.220
vpn-tunnel-protocol ikev2 ssl-client
default-domain value moxiefl.com
webvpn
anyconnect profiles value AnyConnect_client_profile type user
username user1 password $$$$$$$$$$$$$$$$$ encrypted privilege 15
username user2 password $$$$$$$$$$$$$$$$$ encrypted privilege 15
tunnel-group AnyConnect type remote-access
tunnel-group AnyConnect general-attributes
address-pool VPN_POOL
default-group-policy GroupPolicy_AnyConnect
tunnel-group AnyConnect webvpn-attributes
group-alias AnyConnect enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:f2c7362097b71bcada023c6bbfc45121
: endHi,
Yes, I have saved the config and did a write erase and reloaded the config, no difference. I rebuilt it once a couple of weeks ago, but that was before I had gotten this far with your assistance. I'll include my ASA and switches configs after this. Here is a little background (took it form the Firewall section issue just because it gives a little insight for the network). I have 2 3560s, one as a L3 switch the other L2 with an etherchannel between them (one of the cables was bad so I am waiting on the replacement to have 2 - Gigabit channels between the switches).
I think our issue with the VPN not getting to the Inside is posibly related to my DMZ issue not getting to the internet.
I am using 2 VLANs on my switch for Guests - one is wired and the other is wireless. I am trying to keep them separate because the wireless are any guest that might be at our restaurant that is getting on WiFi. The wired is for our Private Dining Rooms that vendors may need access and I don't want the wireless being able to see the wired network in that situation.
I have ports on my 3560s that are assigned to VLAN 20 (Guest Wired) and VLAN 22 (Guest Wireless). I am not routing those addresses within the 3560s (one 3560 is setup as a L3 switch). Those VLANs are being L2 switched to the ASA via the trunk to save ports (I tried separating them and used 2 ports on the ASA and it still didn't work). The ASA is providing DCHP for those VLANs and the routing for the DMZ VLANs. I can ping each of the gateways (which are the VLANs on the ASA from devices on the 3560s - 172.26.20.1 and 172.26.22.1. I have those in my DMZ off the ASA so it can control and route the data.
The 3560 is routing for my Corp VLANs. So far I have tested the Wired VLAN 10 (10.1.10.0/24) and it is working and gets to the Internet. I have a default route (0.0.0.0 0.0.0.0) from the L3 switch to e0/1 on the ASA and e0/1 is an Inside interface.
E0/0 on the ASA is my Outside interface and gets it IP from the upstream router (will be an AT&T router/modem when I move it to the building).
So for a simple diagram:
PC (172.26.20.21/24) -----3560 (L2) ------Trunk----(VLAN 20 - DMZ/ VLAN 22 - DMZ2)---- ASA -----Outside ------- Internet (via router/modem)
I will be back at this tomorrow morning - I've been up since 4pm yesterday and it is almost 3pm.
Thank you for all of your assistance.
Jerry
Current ASA Config:
ASA Version 8.4(4)
hostname mxfw
domain-name moxiefl.com
enable password $$$$$$$$$$$$$$$ encrypted
passwd $$$$$$$$$$$$$$$$ encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
shutdown
interface Ethernet0/4
switchport access vlan 20
interface Ethernet0/5
switchport trunk allowed vlan 20,22
switchport mode trunk
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
interface Vlan1
nameif inside
security-level 100
ip address 10.0.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Vlan20
nameif dmz
security-level 50
ip address 172.26.20.1 255.255.255.0
interface Vlan22
nameif dmz2
security-level 50
ip address 172.26.22.1 255.255.255.0
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 208.67.222.222
name-server 208.67.220.220
domain-name moxiefl.com
same-security-traffic permit inter-interface
object network Generic_All_Network
subnet 0.0.0.0 0.0.0.0
object network INSIDE_Hosts
subnet 10.1.0.0 255.255.0.0
object network AnyConnect_Hosts
subnet 192.168.60.0 255.255.255.0
object network NETWORK_OBJ_192.168.60.0_26
subnet 192.168.60.0 255.255.255.192
object network DMZ_Network
subnet 172.26.20.0 255.255.255.0
object network DMZ2_Network
subnet 172.26.22.0 255.255.255.0
object network INSIDE
subnet 10.0.1.0 255.255.255.0
access-list capdmz extended permit icmp host 172.26.20.22 host 208.67.222.222
access-list capdmz extended permit icmp host 208.67.222.222 host 172.26.20.22
access-list capout extended permit icmp host 192.168.1.231 host 208.67.222.222
access-list capout extended permit icmp host 208.67.222.222 host 192.168.1.231
access-list capvpn extended permit icmp host 192.168.60.20 host 10.1.10.23
access-list capvpn extended permit icmp host 10.1.10.23 host 192.168.60.20
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list SPLIT-TUNNEL standard permit 10.0.1.0 255.255.255.0
access-list SPLIT-TUNNEL standard permit 10.1.0.0 255.255.0.0
access-list capins extended permit icmp host 10.1.10.23 host 10.0.1.1
access-list capins extended permit icmp host 10.0.1.1 host 10.1.10.23
pager lines 24
mtu inside 1500
mtu outside 1500
mtu dmz 1500
mtu dmz2 1500
ip local pool VPN_POOL 192.168.60.20-192.168.60.40 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static INSIDE INSIDE destination static AnyConnect_Hosts AnyConnect_Hosts route-lookup
nat (inside,outside) source static INSIDE_Hosts INSIDE_Hosts destination static AnyConnect_Hosts AnyConnect_Hosts route-lookup
nat (dmz,outside) source dynamic Generic_All_Network interface
nat (dmz2,outside) source dynamic Generic_All_Network interface
nat (inside,outside) after-auto source dynamic Generic_All_Network interface
route inside 10.1.0.0 255.255.0.0 10.0.1.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 10.0.0.0 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
fqdn anyconnect.moxiefl.com
subject-name CN=AnyConnect.moxiefl.com
keypair AnyConnect
proxy-ldc-issuer
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate 439a4452
3082026c 308201d5 a0030201 02020443 9a445230 0d06092a 864886f7 0d010105
05003048 311f301d 06035504 03131641 6e79436f 6e6e6563 742e6d6f 78696566
6c2e636f 6d312530 2306092a 864886f7 0d010902 1616616e 79636f6e 6e656374
2e6d6f78 6965666c 2e636f6d 301e170d 31333039 32373037 32353331 5a170d32
33303932 35303732 3533315a 3048311f 301d0603 55040313 16416e79 436f6e6e
6563742e 6d6f7869 65666c2e 636f6d31 25302306 092a8648 86f70d01 09021616
616e7963 6f6e6e65 63742e6d 6f786965 666c2e63 6f6d3081 9f300d06 092a8648
86f70d01 01010500 03818d00 30818902 8181009a d9f320ff e93d4fdd cb707a4c
b4664c47 6d2cc639 4dc45fed bfbc2150 7109fd81 5d6a5252 3d40dc43 696360d5
fbf92bcc 477d19b8 5301085c daf40de5 87d7e4aa f81b8d7f 8d364dfa 0a6f07d7
6a7c3e9b 56e69152 aa5492d8 e35537bd 567ccf29 7afbeae8 13da9936 9f890d76
1d56d11d da3d039a 0e714849 e6841ff2 5483b102 03010001 a3633061 300f0603
551d1301 01ff0405 30030101 ff300e06 03551d0f 0101ff04 04030201 86301f06
03551d23 04183016 80142f27 7096c4c5 e396e691 e07ef737 af61b71f 64f1301d
0603551d 0e041604 142f2770 96c4c5e3 96e691e0 7ef737af 61b71f64 f1300d06
092a8648 86f70d01 01050500 03818100 8f777196 bbe6a5e4 8af9eb9a 514a8348
5e62d6cd 47257243 e430a758 2b367543 065d4ceb 582bf666 08ff7be1 f89287a2
ac527824 b11c2048 7fd2b50d 35ca3902 6aa00675 e4df7859 f3590596 b1d52426
1e97a52c 4e77f4b0 226dec09 713f7ba9 80bdf7bb b52a7da2 4a68b91b 455cabba
0cc4c6f3 f244f7d9 0a6e32fb 31ce7e35
quit
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev2 remote-access trustpoint ASDM_TrustPoint0
telnet timeout 5
ssh 10.0.0.0 255.0.0.0 inside
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd dns 208.67.222.222 208.67.220.220
dhcpd auto_config outside
dhcpd address 10.0.1.20-10.0.1.40 inside
dhcpd dns 208.67.222.222 208.67.220.220 interface inside
dhcpd enable inside
dhcpd address 172.26.20.21-172.26.20.60 dmz
dhcpd dns 208.67.222.222 208.67.220.220 interface dmz
dhcpd enable dmz
dhcpd address 172.26.22.21-172.26.22.200 dmz2
dhcpd dns 208.67.222.222 208.67.220.220 interface dmz2
dhcpd enable dmz2
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint0 outside
webvpn
enable outside
anyconnect-essentials
anyconnect image disk0:/anyconnect-win-3.0.2052-k9.pkg 1
anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml
anyconnect enable
tunnel-group-list enable
group-policy GroupPolicy_AnyConnect internal
group-policy GroupPolicy_AnyConnect attributes
wins-server none
dns-server value 208.67.222.222 208.67.220.220
vpn-tunnel-protocol ikev2 ssl-client
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SPLIT-TUNNEL
default-domain value moxiefl.com
webvpn
anyconnect profiles value AnyConnect_client_profile type user
username user1 password $$$$$$$$$$$$$ encrypted privilege 15
username user2 password $$$$$$$$$$$ encrypted privilege 15
tunnel-group AnyConnect type remote-access
tunnel-group AnyConnect general-attributes
address-pool VPN_POOL
default-group-policy GroupPolicy_AnyConnect
tunnel-group AnyConnect webvpn-attributes
group-alias AnyConnect enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:f6d9bbacca2a5c8b5af946a8ddc12550
: end
L3 3560 connects to ASA via port f0/3 routed port 10.0.1.0/24 network
Connects to second 3560 via G0/3 & G0/4
version 12.2
no service pad
no service timestamps debug uptime
no service timestamps log uptime
service password-encryption
hostname mx3560a
boot-start-marker
boot-end-marker
enable secret 5 $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
no aaa new-model
system mtu routing 1500
authentication mac-move permit
ip subnet-zero
ip routing
ip dhcp excluded-address 10.1.10.1 10.1.10.20
ip dhcp excluded-address 10.1.12.1 10.1.12.20
ip dhcp excluded-address 10.1.14.1 10.1.14.20
ip dhcp excluded-address 10.1.16.1 10.1.16.20
ip dhcp excluded-address 10.1.30.1 10.1.30.20
ip dhcp excluded-address 10.1.35.1 10.1.35.20
ip dhcp excluded-address 10.1.50.1 10.1.50.20
ip dhcp excluded-address 10.1.80.1 10.1.80.20
ip dhcp excluded-address 10.1.90.1 10.1.90.20
ip dhcp excluded-address 10.1.100.1 10.1.100.20
ip dhcp excluded-address 10.1.101.1 10.1.101.20
ip dhcp pool VLAN10
network 10.1.10.0 255.255.255.0
default-router 10.1.10.1
dns-server 208.67.222.222 208.67.220.220
ip dhcp pool VLAN12
network 10.1.12.0 255.255.255.0
default-router 10.1.12.1
dns-server 208.67.222.222 208.67.220.220
ip dhcp pool VLAN14
network 10.1.14.0 255.255.255.0
default-router 10.1.14.1
option 150 ip 10.1.13.1
ip dhcp pool VLAN16
network 10.1.16.0 255.255.255.0
default-router 10.1.16.1
dns-server 208.67.222.222 208.67.220.220
ip dhcp pool VLAN30
network 10.1.30.0 255.255.255.0
default-router 10.1.30.1
dns-server 208.67.222.222 208.67.220.220
ip dhcp pool VLAN35
network 10.1.35.0 255.255.255.0
default-router 10.1.35.1
dns-server 208.67.222.222 208.67.220.220
ip dhcp pool VLAN50
network 10.1.50.0 255.255.255.0
default-router 10.1.50.1
option 43 hex f104.0a01.6564
ip dhcp pool VLAN80
network 10.1.80.0 255.255.255.0
default-router 10.1.80.1
dns-server 208.67.222.222 208.67.220.220
ip dhcp pool VLAN90
network 10.1.90.0 255.255.255.0
default-router 10.1.90.1
dns-server 208.67.222.222 208.67.220.220
ip dhcp pool VLAN100
network 10.1.100.0 255.255.255.0
default-router 10.1.100.1
ip dhcp pool VLAN101
network 10.1.101.0 255.255.255.0
default-router 10.1.101.1
ip dhcp pool VLAN40
dns-server 208.67.222.222 208.67.220.220
port-channel load-balance src-dst-mac
spanning-tree mode pvst
spanning-tree etherchannel guard misconfig
spanning-tree extend system-id
vlan internal allocation policy ascending
interface Port-channel1
switchport trunk encapsulation dot1q
switchport mode trunk
link state group 1 downstream
interface FastEthernet0/1
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
power inline never
interface FastEthernet0/2
switchport access vlan 10
switchport mode access
power inline never
interface FastEthernet0/3
description Interface to MXFW E0/1
no switchport
ip address 10.0.1.2 255.255.255.0
power inline never
interface FastEthernet0/4
switchport mode access
shutdown
power inline never
interface FastEthernet0/5
switchport mode access
shutdown
power inline never
interface FastEthernet0/6
switchport mode access
shutdown
power inline never
interface FastEthernet0/7
switchport trunk encapsulation dot1q
switchport trunk native vlan 30
switchport mode trunk
switchport voice vlan 14
power inline never
spanning-tree portfast
interface FastEthernet0/8
switchport access vlan 30
switchport mode access
power inline never
interface FastEthernet0/9
switchport mode access
shutdown
power inline never
interface FastEthernet0/10
switchport mode access
shutdown
power inline never
interface FastEthernet0/11
switchport mode access
shutdown
power inline never
interface FastEthernet0/12
switchport access vlan 40
switchport mode access
interface FastEthernet0/13
switchport access vlan 40
switchport mode access
interface FastEthernet0/14
switchport access vlan 40
switchport mode access
interface FastEthernet0/15
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/16
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/17
switchport access vlan 50
switchport mode access
interface FastEthernet0/18
switchport mode access
shutdown
power inline never
interface FastEthernet0/19
switchport mode access
shutdown
power inline never
interface FastEthernet0/20
switchport trunk encapsulation dot1q
switchport trunk native vlan 10
switchport mode trunk
switchport voice vlan 14
spanning-tree portfast
interface FastEthernet0/21
switchport mode access
shutdown
power inline never
interface FastEthernet0/22
switchport mode access
shutdown
power inline never
interface FastEthernet0/23
switchport trunk encapsulation dot1q
switchport trunk native vlan 30
switchport mode trunk
switchport voice vlan 14
spanning-tree portfast
interface FastEthernet0/24
switchport access vlan 35
switchport mode access
power inline never
interface FastEthernet0/25
switchport mode access
shutdown
power inline never
interface FastEthernet0/26
switchport mode access
shutdown
power inline never
interface FastEthernet0/27
switchport mode access
shutdown
power inline never
interface FastEthernet0/28
switchport access vlan 40
switchport mode access
interface FastEthernet0/29
switchport access vlan 40
switchport mode access
interface FastEthernet0/30
switchport access vlan 40
switchport mode access
interface FastEthernet0/31
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/32
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/33
switchport access vlan 50
switchport mode access
interface FastEthernet0/34
switchport mode access
shutdown
power inline never
interface FastEthernet0/35
switchport mode access
shutdown
power inline never
interface FastEthernet0/36
switchport trunk encapsulation dot1q
switchport trunk native vlan 10
switchport mode trunk
switchport voice vlan 14
spanning-tree portfast
interface FastEthernet0/37
switchport mode access
shutdown
power inline never
interface FastEthernet0/38
switchport mode access
shutdown
power inline never
interface FastEthernet0/39
switchport access vlan 30
switchport mode access
power inline never
interface FastEthernet0/40
switchport access vlan 90
switchport mode access
power inline never
interface FastEthernet0/41
switchport mode access
shutdown
power inline never
interface FastEthernet0/42
switchport mode access
shutdown
power inline never
interface FastEthernet0/43
switchport mode access
shutdown
power inline never
interface FastEthernet0/44
switchport access vlan 40
switchport mode access
interface FastEthernet0/45
switchport access vlan 40
switchport mode access
interface FastEthernet0/46
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/47
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/48
switchport mode access
shutdown
power inline never
interface GigabitEthernet0/1
description Interface to MXC2911 Port G0/0
no switchport
ip address 10.1.13.2 255.255.255.0
interface GigabitEthernet0/2
shutdown
interface GigabitEthernet0/3
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode on
interface GigabitEthernet0/4
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode on
interface Vlan1
no ip address
shutdown
interface Vlan10
ip address 10.1.10.1 255.255.255.0
interface Vlan12
ip address 10.1.12.1 255.255.255.0
interface Vlan14
ip address 10.1.14.1 255.255.255.0
interface Vlan16
ip address 10.1.16.1 255.255.255.0
interface Vlan20
ip address 172.26.20.1 255.255.255.0
interface Vlan22
ip address 172.26.22.1 255.255.255.0
interface Vlan30
ip address 10.1.30.1 255.255.255.0
interface Vlan35
ip address 10.1.35.1 255.255.255.0
interface Vlan40
ip address 10.1.40.1 255.255.255.0
interface Vlan50
ip address 10.1.50.1 255.255.255.0
interface Vlan80
ip address 172.16.80.1 255.255.255.0
interface Vlan86
no ip address
shutdown
interface Vlan90
ip address 10.1.90.1 255.255.255.0
interface Vlan100
ip address 10.1.100.1 255.255.255.0
interface Vlan101
ip address 10.1.101.1 255.255.255.0
router eigrp 1
network 10.0.0.0
network 10.1.13.0 0.0.0.255
network 10.1.14.0 0.0.0.255
passive-interface default
no passive-interface GigabitEthernet0/1
ip classless
ip route 0.0.0.0 0.0.0.0 FastEthernet0/3 10.0.1.1
ip route 192.168.60.0 255.255.255.0 FastEthernet0/3 10.0.1.1 2
ip http server
ip sla enable reaction-alerts
line con 0
logging synchronous
line vty 0 4
login
line vty 5 15
login
end
L3 3560 Route Table (I added 192.168.60.0/24 instead of just using the default route just in case it wasn't routing for some reason - no change)
mx3560a#sho ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 10.0.1.1 to network 0.0.0.0
S 192.168.60.0/24 [2/0] via 10.0.1.1, FastEthernet0/3
172.16.0.0/24 is subnetted, 1 subnets
C 172.16.80.0 is directly connected, Vlan80
172.26.0.0/24 is subnetted, 2 subnets
C 172.26.22.0 is directly connected, Vlan22
C 172.26.20.0 is directly connected, Vlan20
10.0.0.0/8 is variably subnetted, 14 subnets, 2 masks
C 10.1.10.0/24 is directly connected, Vlan10
D 10.1.13.5/32 [90/3072] via 10.1.13.1, 4d02h, GigabitEthernet0/1
C 10.1.14.0/24 is directly connected, Vlan14
C 10.1.13.0/24 is directly connected, GigabitEthernet0/1
C 10.1.12.0/24 is directly connected, Vlan12
C 10.0.1.0/24 is directly connected, FastEthernet0/3
C 10.1.30.0/24 is directly connected, Vlan30
C 10.1.16.0/24 is directly connected, Vlan16
C 10.1.40.0/24 is directly connected, Vlan40
C 10.1.35.0/24 is directly connected, Vlan35
C 10.1.50.0/24 is directly connected, Vlan50
C 10.1.90.0/24 is directly connected, Vlan90
C 10.1.101.0/24 is directly connected, Vlan101
C 10.1.100.0/24 is directly connected, Vlan100
S* 0.0.0.0/0 [1/0] via 10.0.1.1, FastEthernet0/3
I have a C2911 for CME on G0/1 - using it only for that purpose at this time.
L2 3560 Config it connects to the ASA as a trunk on e0/5 of the ASA and port f0/3 of the switch - I am using L2 switching for the DMZ networks from the switches to the ASA and allowing the ASA to provide the DHCP and routing out of the network. DMZ networks: 172.26.20.0/24 and 172.26.22.0/24.
version 12.2
no service pad
no service timestamps debug uptime
no service timestamps log uptime
service password-encryption
hostname mx3560b
boot-start-marker
boot-end-marker
enable secret 5 $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
no aaa new-model
system mtu routing 1500
crypto pki trustpoint TP-self-signed-3877365632
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3877365632
revocation-check none
rsakeypair TP-self-signed-3877365632
crypto pki certificate chain TP-self-signed-3877365632
certificate self-signed 01
30820240 308201A9 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33383737 33363536 3332301E 170D3933 30333031 30303031
30395A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 38373733
36353633 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100DF81 DA515E0B 7FC760CF 2CC98400 42DCA007 215E4DDE D0C3FBF2 D974CE85
C46A8700 6AE44C2C 79D9BD2A A9297FA0 2D9C2BE4 B3941A2F 435AC4EA 17E89DFE
34EC8E93 63BD4CDF 784E91D7 2EE0093F 06CC97FD 83CB818B 1ED624E6 F0F5DA51
1DE4B8A7 169EED2B 40575B81 BADDE052 85BA9D19 4C206DCB 00878FF3 89E74028
B3F30203 010001A3 68306630 0F060355 1D130101 FF040530 030101FF 30130603
551D1104 0C300A82 086D7833 35363062 2E301F06 03551D23 04183016 80147125
78CE8540 DB95D852 3C0BD975 5D9C6EB7 58FC301D 0603551D 0E041604 14712578
CE8540DB 95D8523C 0BD9755D 9C6EB758 FC300D06 092A8648 86F70D01 01040500
03818100 94B98410 2D9CD602 4BD16181 BCB7C515 77C8F947 7C4AF5B8 281E3131
59298655 B12FAB1D A6AAA958 8473483C E993D896 5251770B 557803C0 531DEB62
A349C057 CB473F86 DCEBF8B8 7DDE5728 048A49D0 AB18CE8C 8257C00A C2E06A63
B91F872C 5F169FF9 77DC523B AB1E3965 C6B67FCC 84AE11E9 02DD10F0 C45EAFEA 41D7FA6C
quit
port-channel load-balance src-dst-mac
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
interface Port-channel1
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/1
switchport access vlan 50
switchport mode access
interface FastEthernet0/2
switchport access vlan 30
switchport mode access
power inline never
interface FastEthernet0/3
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 20,22
switchport mode trunk
power inline never
interface FastEthernet0/4
switchport mode access
shutdown
power inline never
interface FastEthernet0/5
shutdown
power inline never
interface FastEthernet0/6
shutdown
power inline never
interface FastEthernet0/7
switchport trunk encapsulation dot1q
switchport trunk native vlan 30
switchport mode trunk
switchport voice vlan 14
spanning-tree portfast
interface FastEthernet0/8
switchport access vlan 30
switchport mode access
power inline never
interface FastEthernet0/9
shutdown
power inline never
interface FastEthernet0/10
switchport access vlan 20
switchport mode access
power inline never
interface FastEthernet0/11
shutdown
power inline never
interface FastEthernet0/12
switchport access vlan 40
switchport mode access
interface FastEthernet0/13
switchport access vlan 40
switchport mode access
interface FastEthernet0/14
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/15
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/16
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/17
switchport access vlan 10
switchport mode access
power inline never
interface FastEthernet0/18
shutdown
power inline never
interface FastEthernet0/19
shutdown
power inline never
interface FastEthernet0/20
switchport trunk encapsulation dot1q
switchport trunk native vlan 10
switchport mode trunk
switchport voice vlan 14
spanning-tree portfast
interface FastEthernet0/21
shutdown
power inline never
interface FastEthernet0/22
shutdown
power inline never
interface FastEthernet0/23
switchport access vlan 30
switchport mode access
power inline never
interface FastEthernet0/24
shutdown
power inline never
interface FastEthernet0/25
switchport access vlan 20
switchport mode access
power inline never
interface FastEthernet0/26
shutdown
power inline never
interface FastEthernet0/27
shutdown
power inline never
interface FastEthernet0/28
switchport access vlan 40
switchport mode access
interface FastEthernet0/29
switchport access vlan 40
switchport mode access
interface FastEthernet0/30
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/31
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/32
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/33
switchport access vlan 20
switchport mode access
power inline never
interface FastEthernet0/34
shutdown
power inline never
interface FastEthernet0/35
shutdown
power inline never
interface FastEthernet0/36
switchport mode access
switchport voice vlan 14
spanning-tree portfast
interface FastEthernet0/37
shutdown
power inline never
interface FastEthernet0/38
shutdown
power inline never
interface FastEthernet0/39
switchport access vlan 30
switchport mode access
power inline never
interface FastEthernet0/40
switchport access vlan 90
switchport mode access
power inline never
interface FastEthernet0/41
shutdown
power inline never
interface FastEthernet0/42
shutdown
power inline never
interface FastEthernet0/43
shutdown
power inline never
interface FastEthernet0/44
switchport access vlan 40
switchport mode access
interface FastEthernet0/45
switchport access vlan 40
switchport mode access
interface FastEthernet0/46
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/47
switchport access vlan 40
switchport mode access
shutdown
interface FastEthernet0/48
switchport access vlan 40
switchport mode access
shutdown
interface GigabitEthernet0/1
shutdown
interface GigabitEthernet0/2
switchport access vlan 40
switchport mode access
interface GigabitEthernet0/3
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode on
interface GigabitEthernet0/4
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 1 mode on
interface Vlan1
no ip address
ip classless
ip http server
ip http secure-server
ip sla enable reaction-alerts
line con 0
logging synchronous
line vty 0 4
login
line vty 5 15
login
end -
Hi
We are developing an email tracking application to identify number of times an email is opened
Following are the steps what we are doing to achieve this
- 1. we embedded a tracking url while
sending an email, which get called at the recipient location 2.
This helps us to track the number times the email open count in our node server which sits in our Data Center DMZ
Issue : The tracking URL also called when the sender of the email tries to open his / her email from sent items
folder, so the tracking count increases (need a solution for this)
ThaScenario 2 - The embedded URL gets called everytime the recipient opens the mail, so we get the count
Issue : the URL also gets called when the user clicks on reply / reply all / forward, the email count increases
this should not happen as well need a solution for this as well
Someone Pls HelpHi,
Did you develop a Mail App or an Outlook Add-in?
According to your description, I think the behavior is expected since the embedded URL will be called when displaying the content (reply and forward will also include the original message).
To track the message you sent in Outlook, I think you can achieve it through
Get delivery and read receipt confirmations.
Regards,
Jeffrey
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
Issue with cookies in DMZ multi node envt
Hi ,
We are facing the following issue at our client site:
The client has implemented iStore and iSupport on top of the existing Oracle Applications (11.5.10 ).
For these two modules they have added the DMZ node for their customers to make istore order and to use isupport.
And for the other internal users who use the other modules they have the internal node. Both the internal and external nodes have different domain name.
They also have some internal users having access to their istore and isupport as well as other module access. So they access the apps both from the external and internal nodes.
The issue is, that when the user log-on to istore/isupport thru the external node (eccp.company.com domain).
Once they are in istore/isupport pages, without log-off or closing the browser, if the user goes to the internal node url AppsLocalLogin.jsp (prodapp01.company.com) on the same browser with a difft user name, he gets the resp. of the user who had logged thru the external node on the home page with the LAF changes for iStore and iSupport. But it will not allow them to navigate further. So the users wont see their regular home page when they logon to the internal node in this case. This might be because the home page (AppsLocalLogin) doesn’t associate the correct cookie when the user log-on thru the internal node on the same browser (The browser has both the cookies).
How to solve this issue? Is there any set-up/patch available for this scenario? Any help on this is greatly appreciated.I don't see much relevance of this issue with OAF. It is more of your DMZ setup issue. For better response, you can post it in forum "Managing Oracle Applications" http://forums.oracle.com/forums/forum.jspa?forumID=40&start=0
--Shiv -
Performance issue in guest access anchored in DMZ
Hello,
I've been having performance issue in our wifi guest network anchored in the DMZ.
I have 3-5508 anchor controllers behind the Checkpoint gaia firewall and have 24 guest SSIDs in here.
Right now, only 14 guest SSIDs are enabled and tunnelled out in this anchor DMZ setup, whenever I try to add few more SSIDs I run into performance issue.
It seems to me that the problem is not about these additional SSIDs that I add because the performance issue starts to appear only when the traffic peaks or associated clients reached to certain number which is in my case 4000 users.
The firewall serves as the NAT device and gateway for all these guest SSIDs. The cpu, memory, number of connections have been checked and verified low.
Has anyone seen a problem like this? or has a setup like mine?
thanks!Presuming you're not exceeding client count maximums on the individual WLCs I can't say I've seen anything in line with this "specific problem", but anything is possible.
What are the specific "performance issues" the clients are experiencing? Is it just general poor performance (slow web browsing/etc) or do you see other issues like no internet connectivity at all or something else?
May I ask, what is the use-case behind having 24 SSIDs on your anchors? -
Hi,
We have an Oracle database server 11.2.0.1 that run in Oracle Linux version 3.8.13-16.2.3.el6uek.x86_64, and a Linux 32-bit client server that run in Linux CentOS 6.2.
From the 32-bit client server in the DMZ if we run the query below by sqlplus we have no problem. When we run the same query from the same client server but by php page, it does not return more than 65 row. But (WHERE ROWNUM <= 64) it returns the result fine. If we move the 32-bit client server into LAN, we do not have the issue at all. If you have experience with DMZ or firewall for the situation, please help.
Php query:
'SELECT * FROM (SELECT
p.T$NAMA AS NAMA,
o.T$ORNO AS ORNO,
CASE CAST(o.T$CORG AS INT )
WHEN 1 THEN \'Contracts\'
WHEN 2 THEN \'Quotations\'
WHEN 3 THEN \'EDI\'
WHEN 4 THEN \'Manual\'
WHEN 5 THEN \'Phone\'
WHEN 6 THEN \'Fax\'
WHEN 7 THEN \'Mail\'
WHEN 8 THEN \'Opportunity\'
WHEN 9 THEN \'CRM\'
WHEN 10 THEN \'Consumption\'
WHEN 14 THEN \'Order Template\'
WHEN 21 THEN \'Service\'
WHEN 22 THEN \'Intercompany EDI\'
WHEN 25 THEN \'Retro-Billing\'
WHEN 30 THEN \'Planning\'
WHEN 35 THEN \'Purchase\'
WHEN 40 THEN \'Shipment\'
ELSE \'Unknown\'
END AS ORD_ORIGIN,
CASE CAST(o.T$HDST AS INT )
WHEN 2 THEN \'Suspended\'
WHEN 5 THEN \'Free\'
WHEN 10 THEN \'Approved\'
WHEN 20 THEN \'In Process\'
WHEN 25 THEN \'Modified\'
WHEN 30 THEN \'Closed\'
WHEN 35 THEN \'Cancelled\'
WHEN 40 THEN \'Blocked\'
WHEN 45 THEN \'Released\'
WHEN 50 THEN \'Not Applicable\'
ELSE \'Unknown\'
END AS ORD_STATUS,
o.T$ODAT AS ODAT,
o.T$CORN AS CORN,
SUM((l.T$OAMT)) AS ORD_TOT
FROM
INFOR.TTDSLS400104 o,
INFOR.TTDSLS401104 l,
INFOR.TTCCOM100104 p
WHERE
o.T$ORNO = l.T$ORNO AND
p.T$BPID (+)= o.T$STBP AND
o.T$OFBP = \'210008000\' AND
o.T$ODAT BETWEEN to_date(\'07/14/2014\', \'MM-DD-YYYY\') and to_date(\'08/14/2014\', \'MM-DD-YYYY\')
GROUP BY
p.T$NAMA,
o.T$ORNO,
o.T$ODAT,
o.T$CORN,
o.T$STBP,
o.T$CORG,
o.T$HDST
ORDER BY
o.T$ODAT DESC ) WHERE ROWNUM <= 65';Maybe you run the statement with 2 different users and there could be some policies enabled for those tables ( VPD )
-
ISSUE with accessing Printer on the DMZ !!
Hi,
We are facing issues while accesing the printer in the DMZ interface from inside interface.The issue is happening when we are adding a printer to a new desktop. The printer is added via print server.The issue started happening after the server team has implemented authentication PIN for printing.The printer gets added but while giving print ,it is giving error as print driver not found.We have checked printing after removing the PIN and it works fine.I am getting the following error logs from firewall.Can somebody help on this ???
%ASA-6-302014: Teardown TCP connection 3842514 for DMZ:172.19.48.207/80 to ODC-FW:10.132.123.19/1810 duration 0:00:06 bytes 711 TCP Reset-I
%ASA-6-302014: Teardown TCP connection 3842514 for DMZ:172.19.48.207/80 to ODC-FW:10.132.123.19/1810 duration 0:00:06 bytes 711 TCP Reset-I
172.19.48.207 -Printer
10.132.123.19-DesktopMujeeb,
Based on the syslog you post we are getting a Reset from the internal device, the FW is just closing the connection becuase it got a reset packet; this will be the normal behaviour of the ASA.
If you want to dig deeper on the issue you can place captures on the ASA and confirm the source mac-address/IP address of the reset packet.
Luis Silva -
Wireless WISM and 4402 DMZ controller mobility issue
Hi all,
I have a really weird wireless mobility issue I need help with. I have a Wism installed in our cat 6 with version 7.0.98.0 of software. I also have a 4402 controller in the DMZ acting as an anchor controller to terminate guest traffic, also running the same version of software. The mobility anchor is setup on 4 SSID's and most of the time I don't have an issue with it.
However every week or so the data path or control path will randomly go down, so no guest traffic. Timers are configured as 10 seconds for the keep alive count and 20 seconds for the keep alive interval. I have found the following syslog information from our NMS. Not sure what these errors are and if its anything to do with this random mobility issue.
Any thoughts ??A traceback is a device producing a trace of where it was in the software code when the problem occured.
Most often it's when a function fails/crashes. Although that is not always true.
If you have the syslog to the deepest level of debug, you will see harmless tracebacks (functions that returned no result but that might be expected). On higher level of debugs only "crashing" tracebacks are shown. In this case, the fact that you have mobility issues and tracebacks related to mobility is highly suspicious.
TAC can decrypt the traceback hex and find the exact part of code that created the problem. From there, they can link it to an existing bug (or a new one maybe ?).
Hope this clarifies !
Nicolas
===
Please rate answers that you find useful -
Workflow issue after configuring DMZ.
Hi,
I am facing issues with regards to my worflow, after configuring DMZ.
Recently we have configured DMZ, As per the document 380490.1.
Database tier : bwerpdbs02
Internal Application tier : bwerp
Dmz tier : bwerpgrd04
Our SMTP server name is bsf-hc-01. whenever the internal application tier is bounced the SMTP server name gets changed to bwerpgrd04 which is not my SMTP/IMAP server name.
Everytime the internal application is bounced, i need to do the changes manually in the workflow configuration tab ie : Changing of the SMTP server name from bwerpgrd04 to bsf-hc-01.
EBS :
12.1.3
DB:
11.2.0.1
Please check and revert.
Thanks,
Fahim.Hi;
Did you check under Configure Apache - put this in a small script (runc.sh), that way you have a record of how it was configured part at in same doc?
Regard
Helios -
Issuing Certificates to a DMZ server
I'm in the process of setting up a PKI infrastructure for an SCCM 2012 environment. In order to manage travelling laptops over the internet, we installed a new Windows 2012 R2 server in the DMZ. To communicate properly with the travelling
SCCM clients, we need to install 2 certificates on this DMZ server. This DMZ server is in a different forest/domain than the SCCM and CA server, with no trusts established between it and our production domain. If it makes any difference, there
is also no DNS forwarding, but I have added an entry to the hosts file on the DMZ server, and to the internal CA and SCCM servers (all Windows 2012 R2), so that they can resolve each other.
I've created the 2 certificate templates per the SCCM documentation on the internal CA server, but in the Security tab, there is no way for me to add the DMZ server for the "Read and Enroll" rights (since it's in another, untrusted forest.)
Since I can't enroll the certificates through the MMC console of the DMZ server, my next thought was that I could use the CA web enrollment method, and try to get certificates enrolled that way. However, when I type in
http://MY_CA_SERVER/certsrv, Internet Explorer spins for about 10-15 seconds, and then I get "Page cannot be displayed." I added the webpage to the Trusted Sites in IE, but that did not help. Visiting
the CA webpage from a domain-joined computer works fine; it's just not working from the DMZ server.
Does this sound like a communications/port issue? Between my internal domain and this DMZ server, I've currently got ports 80, 135, 443, 445, 1433, 8530, and 8531 open. Do I need anything additional for Certificate Authority communication?
If I'm not approaching this in the correct manner, I'm also open to other suggestions on how to install these 2 certificates properly.
Thanks in advance for any advice.> I've currently got ports 80, 135, 443, 445, 1433, 8530, and 8531 open.
please, close RPC ports in your perimeter firewall. Instead of using legace web pages, I would consider to set up a new Certificate Enrollment Web Servcies (which first appeared in Windows Server 2008 R2):
http://social.technet.microsoft.com/wiki/contents/articles/7734.certificate-enrollment-web-services-in-active-directory-certificate-services.aspx
if it is not possible to install CEP/CES services, then you can use the following guide (although it requires some manual procedures):
http://en-us.sysadmins.lv/Lists/Posts/Post.aspx?ID=5
My weblog: en-us.sysadmins.lv
PowerShell PKI Module: pspki.codeplex.com
PowerShell Cmdlet Help Editor pscmdlethelpeditor.codeplex.com
Check out new: SSL Certificate Verifier
Check out new:
PowerShell FCIV tool. -
I have a Solaris 10 box with two NIC's one is connected to my internal LAN and the other to my DMZ. The NIC on the DMZ is not plumbed and is being used in a VM using VirtualBox. Everything seems to be functioning correctly except when inside my VM (On the DMZ) I am able to see my other NIC's IP (On the internal LAN), however it is unable to see any other machine on my internal LAN. So I am thinking that Solaris looks at the packets and says oh you are trying to reach me and responds directly without first running through my firewall. Is this assumption correct? If so how can I fix this? If not do you have any other ideas what might be causing this?
Thanks
TravisSo after some research I found that when using bridge mode with Virtualbox the host machine will scan all packets, to prevent this I need to use internal mode, however I do not see anyway to specify which NIC I want to use for 'internal'. So my new thought is to use a zone with ip exclusive and then run virtualbox inside of that. Is this going to be a large performance issue?
Maybe you are looking for
-
Why can't i sync songs from other sources in my library into my iPhone?
why can't i play songs from other sources in my liberay that i sync in my phone
-
Hi all i try to put color in the dynamic alv, but i become a dump message Runtime Errors OBJECTS_MOVE_NOT_SUPPORTED Date and Time 28.10.2010 08:46:49 Short text Conversion of type "h" to type "g" not supported. What happened?
-
HT4993 I deleted my Calendar app - how do I get it back?
I deleted the Calendar App on my iPhone 4S - how do i get it back??
-
Need some help with a case statement implementation
I am having trouble using a CASE statement to compare values and then display the results. The other issue is that i want to put these results in a separate column somehow. Heres how the code would look: SELECT "Task"."Code", "Stat" = CASE WHEN "Task
-
Simple Round call results in Arithmetic overflow
Hi, I'm a bit dazzled why this statement won't work in T-SQL : Select Round(9.990000, 0) The error I get is : Arithmetic overflow error converting expression to data type numeric. The result should be : 10 I've tried this in SQL 2005,2008 and 2008 R2