Droid X freezing, starting and restarting on its own.

Last week I had to replace my Droid X. When I rec'd the replacement today, I pulled it out of the box, inserted the battery and fired it up. Called to activate the phone, started the set up process. It got all the way to the Back Up Assistant, then flipped itself off and restarted itself, but wouldn't let me do anything else. Nothing. Period. The little green light was flashing, indicating I had texts, voice mails, emails, etc, but the screen is blank. Occassionally the screen will show the time and date, but won't let me swipe to unlock it. The old phone did this same thing before I had it replaced. What's the problem? Yes, I've already done the "hold down the power and the home button to wipe/delete..." thing at least three times. No go. Is there a software snafu with Verizon going on?
Thanks for any help.

Hmm. There could be some wireless interference or conflict with other networks or devices. I suggest that you try changing the wireless channel. I am using channel 9 for my EA4500 router, but you can also try other channels and see which one suits your network setup. What’s the current firmware version of the router?
If it has an up to date firmware, you can relfash it to make sure that there’s nothing wrong with firmware that was uploaded. Simply download the firmware file and manually load it to your router. 
Help, learn and share

Similar Messages

  • Imac shuts down and restarts on its own

    Hello
    I am having a problem with my 2011 Imac i7. Usually when at the screen saver the computer will shut down and display an error message. Something along the lines of "your computer has experienced and problem and is restarting". It flashes to a grey screen and then a message apears in a white dialog box.  Any help would be greatly appreciated. Below is the error report that shows up when the computer restarts.
    Interval Since Last Panic Report:  223448 sec
    Panics Since Last Report:          2
    Anonymous UUID:                   
    Tue Feb 26 19:12:25 2013
    Panic(CPU 0): NMIPI for spinlock acquisition timeout, spinlock: 0xffffff8053bf8108, spinlock owner: 0xffffff8055aa3000, current_thread: 0xffffff8055aa3000, spinlock_owner_cpu: 0x0
    RAX: 0x00000000000000fe, RBX: 0xffffff8054711680, RCX: 0x5217b27900000000, RDX: 0xffffff826c92b000
    RSP: 0xffffff825b160ec0, RBP: 0xffffff825b160f40, RSI: 0xffffff825b160ef8, RDI: 0xffffff8054711680
    R8:  0x0000000000000001, R9:  0x00000000000003ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
    R12: 0xffffff825b160ef8, R13: 0xffffff80546f8f80, R14: 0xffffff8054a40000, R15: 0xffffff825b160f08
    RFL: 0x0000000000000006, RIP: 0xffffff7faacbd046, CS:  0x0000000000000008, SS:  0x0000000000000010
    Backtrace (CPU 0), Frame : Return Address
    0xffffff825b160d40 : 0xffffff80296bd371
    0xffffff825b160d70 : 0xffffff80296b7203
    0xffffff825b160dc0 : 0xffffff80296ce81b
    0xffffff825b160f40 : 0xffffff7fa9c4f825
    0xffffff825b160f50 : 0xffffff7fab2fb62d
    0xffffff825b160f60 : 0xffffff7fab302b5b
    0xffffff825b160f80 : 0xffffff80296b720f
    0xffffff825b160fd0 : 0xffffff80296ce6a8
    0xffffff826db13cd0 : 0xffffff802962caf9
    0xffffff826db13d40 : 0xffffff80299b9efb
    0xffffff826db13f00 : 0xffffff80299ba7ae
    0xffffff826db13f50 : 0xffffff80299e182a
    0xffffff826db13fb0 : 0xffffff80296ced33
          Kernel Extensions in backtrace:
             com.apple.iokit.IOPCIFamily(2.7.2)[B1B77B26-7984-302F-BA8E-544DD3D75E73]@0xffff ff7fa9c4e000->0xffffff7fa9c72fff
             com.apple.driver.AppleACPIPlatform(1.6)[4F08531B-7E5A-3604-924A-8769CF53458B]@0 xffffff7fab2f5000->0xffffff7fab34bfff
                dependency: com.apple.iokit.IOACPIFamily(1.4)[A35915E8-C1B0-3C0F-81DF-5515BC9002FC]@0xfffff f7faa141000
                dependency: com.apple.iokit.IOPCIFamily(2.7.2)[B1B77B26-7984-302F-BA8E-544DD3D75E73]@0xffff ff7fa9c4e000
          Kernel Extensions in backtrace:
             com.apple.kext.AMD6000Controller(8.0)[B8119AB9-CAB3-374E-917D-294D7365F60A]@0xf fffff7faacbb000->0xffffff7faad00fff
                dependency: com.apple.iokit.IOACPIFamily(1.4)[A35915E8-C1B0-3C0F-81DF-5515BC9002FC]@0xfffff f7faa141000
                dependency: com.apple.iokit.IOPCIFamily(2.7.2)[B1B77B26-7984-302F-BA8E-544DD3D75E73]@0xffff ff7fa9c4e000
                dependency: com.apple.kext.AMDSupport(8.0.0)[7B2EC6D1-101A-3928-919E-337D6724752A]@0xffffff 7faaab6000
                dependency: com.apple.iokit.IOGraphicsFamily(2.3.5)[803496D0-ADAD-3ADB-B071-8A0A197DA53D]@0 xffffff7faa1d2000
    BSD process name corresponding to current thread: ScreenSaverEngin
    Mac OS version:
    12C60
    Kernel version:
    Darwin Kernel Version 12.2.0: Sat Aug 25 00:48:52 PDT 2012; root:xnu-2050.18.24~1/RELEASE_X86_64
    Kernel UUID:
    Kernel slide:     0x0000000029400000
    Kernel text base: 0xffffff8029600000
    System model name: iMac12,2 (Mac-942B59F58194171B)
    System uptime in nanoseconds: 38624848227043
    last loaded kext at 20864124278337: com.apple.driver.AppleUSBCDC          4.1.22 (addr 0xffffff7fab8f5000, size 16384)
    last unloaded kext at 21085252380833: com.apple.driver.AppleUSBCDC          4.1.22 (addr 0xffffff7fab8f5000, size 12288)
    loaded kexts:
    com.Cycling74.driver.Soundflower          1.5.2
    com.squirrels.airparrot.framebuffer          2
    com.squirrels.driver.AirParrotSpeakers          1.6
    com.rim.driver.BlackBerryUSBDriverInt          0.0.74
    com.apple.filesystems.smbfs          1.8
    com.apple.driver.AppleBluetoothMultitouch          75.15
    com.apple.driver.AppleHWSensor          1.9.5d0
    com.apple.filesystems.autofs          3.0
    com.apple.driver.AGPM          100.12.69
    com.apple.iokit.IOBluetoothSerialManager          4.0.9f33
    com.apple.driver.AppleMikeyHIDDriver          122
    com.apple.driver.AudioAUUC          1.60
    com.apple.driver.AppleHDA          2.3.1f2
    com.apple.driver.AppleUpstreamUserClient          3.5.10
    com.apple.iokit.IOUserEthernet          1.0.0d1
    com.apple.kext.AMDFramebuffer          8.0.0
    com.apple.Dont_Steal_Mac_OS_X          7.0.0
    com.apple.iokit.BroadcomBluetoothHCIControllerUSBTransport          4.0.9f33
    com.apple.driver.AppleMikeyDriver          2.3.1f2
    com.apple.AMDRadeonAccelerator          1.0.0
    com.apple.driver.AppleIntelHD3000Graphics          8.0.0
    com.apple.driver.AppleBacklight          170.2.3
    com.apple.driver.ApplePolicyControl          3.2.11
    com.apple.driver.AppleLPC          1.6.0
    com.apple.driver.AppleSMCPDRC          1.0.0
    com.apple.driver.AppleIntelSNBGraphicsFB          8.0.0
    com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
    com.apple.driver.AppleMCCSControl          1.0.33
    com.apple.driver.AppleSMCLMU          2.0.2d0
    com.apple.iokit.SCSITaskUserClient          3.5.1
    com.apple.driver.AppleUSBCardReader          3.1.0
    com.apple.driver.AppleIRController          320.15
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
    com.apple.BootCache          34
    com.apple.driver.XsanFilter          404
    com.apple.iokit.IOAHCIBlockStorage          2.2.2
    com.apple.driver.AppleUSBHub          5.2.5
    com.apple.driver.AirPort.Atheros40          600.70.23
    com.apple.driver.AppleFWOHCI          4.9.6
    com.apple.iokit.AppleBCM5701Ethernet          3.2.5b3
    com.apple.driver.AppleAHCIPort          2.4.1
    com.apple.driver.AppleUSBEHCI          5.4.0
    com.apple.driver.AppleEFINVRAM          1.6.1
    com.apple.driver.AppleACPIButtons          1.6
    com.apple.driver.AppleRTC          1.5
    com.apple.driver.AppleHPET          1.7
    com.apple.driver.AppleSMBIOS          1.9
    com.apple.driver.AppleACPIEC          1.6
    com.apple.driver.AppleAPIC          1.6
    com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
    com.apple.nke.applicationfirewall          4.0.39
    com.apple.security.quarantine          2
    com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
    com.apple.driver.AppleMultitouchDriver          235.28
    com.apple.driver.AppleBluetoothHIDKeyboard          165.5
    com.apple.driver.IOBluetoothHIDDriver          4.0.9f33
    com.apple.driver.AppleHIDKeyboard          165.5
    com.apple.kext.triggers          1.0
    com.apple.iokit.IOSerialFamily          10.0.6
    com.apple.driver.DspFuncLib          2.3.1f2
    com.apple.iokit.IOSurface          86.0.3
    com.apple.iokit.IOBluetoothFamily          4.0.9f33
    com.apple.iokit.AppleBluetoothHCIControllerUSBTransport          4.0.9f33
    com.apple.iokit.IOAudioFamily          1.8.9fc10
    com.apple.kext.OSvKernDSPLib          1.6
    com.apple.iokit.IOAcceleratorFamily          19.0.26
    com.apple.iokit.IOFireWireIP          2.2.5
    com.apple.driver.AppleBacklightExpert          1.0.4
    com.apple.driver.AppleGraphicsControl          3.2.11
    com.apple.iokit.IONDRVSupport          2.3.5
    com.apple.kext.AMD6000Controller          8.0.0
    com.apple.kext.AMDSupport          8.0.0
    com.apple.driver.AppleSMBusPCI          1.0.10d0
    com.apple.driver.AppleHDAController          2.3.1f2
    com.apple.iokit.IOHDAFamily          2.3.1f2
    com.apple.driver.IOPlatformPluginLegacy          1.0.0
    com.apple.driver.IOPlatformPluginFamily          5.2.0d16
    com.apple.driver.AppleSMBusController          1.0.10d0
    com.apple.driver.AppleSMC          3.1.4d2
    com.apple.iokit.IOGraphicsFamily          2.3.5
    com.apple.driver.AppleThunderboltEDMSink          1.1.8
    com.apple.driver.AppleThunderboltEDMSource          1.1.8
    com.apple.driver.AppleThunderboltDPOutAdapter          1.8.5
    com.apple.driver.AppleThunderboltDPInAdapter          1.8.5
    com.apple.driver.AppleThunderboltDPAdapterFamily          1.8.5
    com.apple.driver.AppleThunderboltPCIDownAdapter          1.2.5
    com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
    com.apple.iokit.IOBDStorageFamily          1.7
    com.apple.iokit.IODVDStorageFamily          1.7.1
    com.apple.iokit.IOCDStorageFamily          1.7.1
    com.apple.iokit.IOAHCISerialATAPI          2.5.0
    com.apple.iokit.IOUSBHIDDriver          5.2.5
    com.apple.driver.AppleUSBMergeNub          5.2.5
    com.apple.driver.AppleThunderboltNHI          1.6.0
    com.apple.iokit.IOThunderboltFamily          2.1.1
    com.apple.iokit.IOUSBUserClient          5.2.5
    com.apple.iokit.IO80211Family          500.15
    com.apple.iokit.IOFireWireFamily          4.5.5
    com.apple.iokit.IOEthernetAVBController          1.0.2b1
    com.apple.iokit.IONetworkingFamily          3.0
    com.apple.iokit.IOAHCIFamily          2.2.1
    com.apple.iokit.IOHIDFamily          1.8.0
    com.apple.driver.AppleEFIRuntime          1.6.1
    com.apple.iokit.IOSMBusFamily          1.1
    com.apple.security.sandbox          220
    com.apple.kext.AppleMatch          1.0.0d1
    com.apple.security.TMSafetyNet          7
    com.apple.driver.DiskImages          344
    com.apple.driver.AppleKeyStore          28.21
    com.apple.iokit.IOUSBMassStorageClass          3.5.0
    com.apple.driver.AppleUSBComposite          5.2.5
    com.apple.iokit.IOSCSIBlockCommandsDevice          3.5.1
    com.apple.iokit.IOStorageFamily          1.8
    com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
    com.apple.iokit.IOUSBFamily          5.4.0
    com.apple.driver.AppleACPIPlatform          1.6
    com.apple.iokit.IOPCIFamily          2.7.2
    com.apple.iokit.IOACPIFamily          1.4
    com.apple.kec.corecrypto          1.0
    panic(cpu 6 caller 0xffffff80299ba65d): "Spinlock acquisition timed out: lock=0xffffff8053bf8108, lock owner thread=0xffffff8055aa3000, current_thread: 0xffffff805452caa0, lock owner active on CPU 0x0, current owner: 0xffffff8055aa3000"@/SourceCache/xnu/xnu-2050.18.24/osfmk/i386/locks_i386.c:363
    Backtrace (CPU 6), Frame : Return Address
    0xffffff826ab33e90 : 0xffffff802961d626
    0xffffff826ab33f00 : 0xffffff80299ba65d
    0xffffff826ab33f50 : 0xffffff80299e182a
    0xffffff826ab33fb0 : 0xffffff80296ced33
    BSD process name corresponding to current thread: ScreenSaverEngin
    Model: iMac12,2, BootROM IM121.0047.B1F, 4 processors, Intel Core i7, 3.4 GHz, 20 GB, SMC 1.72f1
    Graphics: AMD Radeon HD 6970M, AMD Radeon HD 6970M, PCIe, 2048 MB
    Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1333 MHz, 0x02FE, 0x45424A3231554538424655302D444A2D4620
    Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1333 MHz, 0x02FE, 0x45424A3231554538424655302D444A2D4620
    Memory Module: BANK 0/DIMM1, 8 GB, DDR3, 1333 MHz, 0x857F, 0x483634314755363746393333334700000000
    Memory Module: BANK 1/DIMM1, 8 GB, DDR3, 1333 MHz, 0x857F, 0x483634314755363746393333334700000000
    AirPort: spairport_wireless_card_type_airport_extreme (0x168C, 0x9A), Atheros 9380: 4.0.70.23-P2P
    Bluetooth: Version 4.0.9f33 10885, 2 service, 18 devices, 1 incoming serial ports
    Network Service: AirPort, AirPort, en1
    Serial ATA Device: WDC WD1001FALS-403AA0, 1 TB
    Serial ATA Device: OPTIARC DVD RW AD-5680H
    USB Device: FaceTime HD Camera (Built-in), apple_vendor_id, 0x850b, 0xfa200000 / 3
    USB Device: hub_device, 0x0424  (SMSC), 0x2514, 0xfa100000 / 2
    USB Device: BRCM2046 Hub, 0x0a5c  (Broadcom Corp.), 0x4500, 0xfa110000 / 4
    USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8215, 0xfa111000 / 5
    USB Device: hub_device, 0x0424  (SMSC), 0x2514, 0xfd100000 / 2
    USB Device: IR Receiver, apple_vendor_id, 0x8242, 0xfd120000 / 4
    USB Device: Internal Memory Card Reader, apple_vendor_id, 0x8403, 0xfd110000 / 3
    Thank you
    Richard

    Hi, though it all points to Graphic card or drivers, Soundflower has been a problem for many, in fact the first 4 non apple kexts may be the problem.
    One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, Test for problem in Safe Mode...
    PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive
    Reboot, test again.
    If it only does it in Regular Boot, then it could be some hardware problem like Video card, (Quartz is turned off in Safe Mode), or Airport, or some USB or Firewire device, or 3rd party add-on, Check System Preferences>Accounts (Users & Groups in later OSX versions)>Login Items window to see if it or something relevant is listed.
    Check the System Preferences>Other Row, for 3rd party Pref Panes.
    Also look in these if they exist, some are invisible...
    /private/var/run/StartupItems
    /Library/StartupItems
    /System/Library/StartupItems
    /System/Library/LaunchDaemons
    /Library/LaunchDaemons

  • Macbook Pro....what would cause it to turn the screen black and restart on its own. Message after it restarts says restarted due to problems.

    Macbook Pro...my screen goes black and it restarts itself. The message after it restarts says "restart due to problems" Any ideas what I should do or look for? It randomly happens and is becomeing more frequent.

    kernel panic http://support.apple.com/kb/ts3742

  • Crashed! And restart on its own.

    I was simply tap tap tapping inside an App - and my iPhone crashed, YET again...........
    I wasn't doing anything crazy, not even memory intensive! I only had 4 apps open total. I'm in one App and am clicking away - and bam! It goes BLANK to black and then restarts by itself.
    Why does this keep happening to me? I don't even have too many Apps! 5 games total, if that! And most of my phone is filled with music, I have no movies, I have some video from the camera, some photos. That's it.
    It only ever crashed once when I was iOS6. Now it's crashed twice in less than 2 weeks and there are glitches all over the place.
    I guess Apple is sending me a message to just buy a new 5S and throw this 4S into the ocean, right?
    Thanks
    iOS7 on 4S.

    This time it was a non-Apple app, but the first time was in the middle of doing nothing, I was trying to click on an App and the phone literally crashed, showed me a dead battery indicator and went blank. I hastily borrowed a friend's plug and got some power and it came back to life that time, and when I unplugged 2 minutes later, it showed the battery where it had left off when it crashed and told me I had no battery.
    I just want the glitches to end. It didn't happen as much with iOS6. OK so this one has whole sale changes to the way it looks and operates and so on - but why release something that had not been fully tested in at least a few incarnations?

  • Recently my iphone 4 is shutting down and restarting on its own. i went to the service provider and they refused to get my phone replaced as my phone has a few glass chip offs at the edges. how can i get my phone replaced?

    pls someone help me on this issue. phone is stil under warranty

    Depends on where in world you are
    If a country where Apple stores exist take it to The Apple Store they will replace however if damaged may well  charge  for the replacement depends on actual condition and how you approach them .If glass is broken probably no chance of a free warranty replacement
    http://support.apple.com/kb/index?page=servicefaq&geo=United_Kingdom&product=iph one
    just pick your country freom drop down menu

  • My Macbook 13inch (2008) shuts down and restarts on its own randomly. why and what needs to be done to fix it?

    For the last three days my macbook has been shutting itself off - and then on again. And I don't know why or what to do.
    I have a new power adapter, but my battery may be bad, which is why I keep the macbook plugged for the time of use. I have worked with my mac with that battery in, I also took it out- it doesn't appear to make a difference. Also: it doesn't matter if I have the mac on a desk or if I move it. It randomly shuts off.
    Also, I have been monitoring the temp and the fan... I believe it operates in ok-range. Why is this happening? And what to do?
    Cheers!

    Hi, though it all points to Graphic card or drivers, Soundflower has been a problem for many, in fact the first 4 non apple kexts may be the problem.
    One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, Test for problem in Safe Mode...
    PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive
    Reboot, test again.
    If it only does it in Regular Boot, then it could be some hardware problem like Video card, (Quartz is turned off in Safe Mode), or Airport, or some USB or Firewire device, or 3rd party add-on, Check System Preferences>Accounts (Users & Groups in later OSX versions)>Login Items window to see if it or something relevant is listed.
    Check the System Preferences>Other Row, for 3rd party Pref Panes.
    Also look in these if they exist, some are invisible...
    /private/var/run/StartupItems
    /Library/StartupItems
    /System/Library/StartupItems
    /System/Library/LaunchDaemons
    /Library/LaunchDaemons

  • EA6500 Signal Dropping off and restarting on its own

    Hi Community, I have a EA6500 AC1750 linksys wireless router.  I recently purchased a new Motorola Modem it is the motorola sbg6782-ac modem.  I have the modem in Bridge mode and the wireless networks on it disabled so that I can use the Linksys AC1750 wireless router as I need to the extended range of the router as my office is upstairs where my internet cable access point is.  I have 10 devices connected to my router, however, I have a 30mbps package from Time Warner.  I can say that I have had a noticeable increase in speed and performance since purchasing the Motorola modem, it's been installed for about a week and the signal has better consistency and quality.  However, I have noticed some funky acitivity with the Linksys router.  I had to previously restore to factory default settings about once a month as the communication between the Linksys and the old Arris Modem from TW that I had was just nonexistent, it seemed like when the lease time expired the communication between modem and router would reset and then I would need to reset to factory defaults in order to reset the communication so it worked properly.  After week 1 with the Motorola that does not seem to be the case as it seems much more consistent.  However, today I was working next to the router and I noticed the Linksys rebooted randomly, and the modem never flinched, since the reboot today I have noticed that the signal is fluctuating with ranges down to 32mbps and then up to 180mbps, however when I work next to my router the speed is a consistent 450mbps with 5 signal bars.  I know the range has something to do with it, but the random rebooting and signal speeds going up and down makes me think it is in some kind of power save mode or something, I can't find anything in the settings that suggests that but that is what it seems like to me.  Please let me know if there is anything in the settings of the router that needs to be adjusted.  (on a side note, I use a VPN connection to work from home on a day to day basis, in addition, I make a lot of VOIP calls and do a lot of webex conferencing using my internet connection.  Also I do use xbox one where I am using matchmaking and playing online)
    Thanks in advance

    Hmm. There could be some wireless interference or conflict with other networks or devices. I suggest that you try changing the wireless channel. I am using channel 9 for my EA4500 router, but you can also try other channels and see which one suits your network setup. What’s the current firmware version of the router?
    If it has an up to date firmware, you can relfash it to make sure that there’s nothing wrong with firmware that was uploaded. Simply download the firmware file and manually load it to your router. 
    Help, learn and share

  • Mac OS 10.5 /  I deleted the " Private" folder ... and emptied the trash. So the folder and its contents no longer exists on my computer at all !!!  I do have the OS dvd that i purchased years ago...  But my computer will not start from it on its own. My

    Mac OS 10.5 /
    I deleted the " Private" folder ... and emptied the trash. So the folder and its contents no longer exists on my computer at all !!!
    I do have the OS 10.5 dvd that i purchased years ago...
    But my computer will not start from it on its own.
    My question is what is the open source or terminal language code used to tell my mac to look in the DVD rom drive for startup info?  I know that im not the only person in this world who has deleted the "PRIVATE" folder and emptied the trash so it no longer exists on their machine...
    That said theres gotta be a common fix for a Power PC G4 that has the OS X dvd in the rom drive but wont look to it to reinstall the vital contents of the PRIVATE folder.
    Once again there is not a copy of this file or its contents in the recycle bin...
    Also rebooting the machine , pressing and holding the letter C does not prompt the machine to look to the dvd rom drive.
    I was reinstalling pro tools and figured I would make some room by cleaning my computers HD...
    Lol It was a bad choice to delete this file ...
    Thanks guys

    Okay sorry it took forever to respond... But for a while there I gave up on this computer!!!!
    Money's been tight lately , so taking it in to a professional was not yet an option... though I did consider it eventhough.
    Anyway long story short im glad I didnt spend any money because I already had all the tools necessary to fix this issue but was going about it in the wrong way. Okay so here is my scenario and the breakdown... Though this may not fix the issue for everyone :( which *****... But I know we all will have different circumstances.
    Anyway here we go...
    Okay so first things first....  Years ago I purchased the OS 10.5.1 disk ... So that has always been in my possession!!!!
    I realize that some may not have a disk to reflash your OS to your hard drive... but if you do your in luck.
    2ndly ... I had an external harddrive with all of my itunes downloaded music so it was more than okay with me to delete my primary HD because all the important stuff could either be copied over or repathed to be located.
    -------If you dont want to read through the whole story the fix is summed up in the bottom section-------
    Okay so now the SOLUTION!!!!
    By trial and error , and pure boredom I opened up my computer to clean the inside...
    AND
    "Disconnected the primary HD"
    and just because ....... REBOOTED my computer. Just to see what it would do.
    Upon restart and though it looked like it would repeat its usual cycle...
    About 1 minute in to that process my computer froze for about 2 seconds and flashed to the OS installation screen.
    Mind you I havent seen this screen yet... Probably hasnt been since I installed the OS years ago.
    After a bit of trial and error...
    I decided to tell my computer to startup from the OS 10.5 disk located in my dvd rom drive and restarted once again...
    this setting is under
    Utilities / startup disk
    After a little more trial and error ... I realized that I could reconnect the primary HD , restart the machine and return to the OS installation menu.
    So upon this discovery
    I went to the Disk Utility located under Utilities
    Highlighted my primary HD located in the left hand column
    Once highlighted ...
    In the heading section on the right I selected the option
    Erase
    in which I erased My current OS on my primary HD ...
    I used the first option in the list under security... Because it seemed like the least invasive and would take the least amount of time to see if this process would actually work.
    I FORGOT to add something... 
    Another reason why I deleted my primary HD!!!!!
    I forgot to say that it WOULD NOT!!!!! Show up in the STARTUP list as an option...Even After multiple reboots....
    But like clockwork... Once I deleted its name IT SHOWED UP as an option!!!!
    So back to the next step...
    I returned to the STARTUP option under utilities ... And was then able to see MY primary HD now as a startup option...
    But ofcourse it had no name because it we previously erased it.
    So when Clicking my newly erased HD ... I was almost immediately prompted to REINSTALL the OS ...
    Which said it would take about 57 minutes ... But I believe was alot less...
    My issue was resolved ... My computer then stated the install was SUCCESSFUL!!!!!!! :))))))))))) lol ;)
    It was like I was setting up for the first time ;) asking for my registration info...
    The dilemma of deleting the private folder and emptying the trash is finally over resolved. Done ... and no extra money spent!!!!!!!!! 
    Its really crazy that the information for such a simple thing is not readily available. Especially being such a simple fix.
    I know im not the only person who's had this issue , because i've seen numerous posts with similar wording.
    I also know I wont be the last person to have this issue... So I hope this synopsis makes sense.
    -------One more time the fix------
    *Insert your OS dvd into your dvd rom drive.
    *Unplug your primary HD or corrupted startup disk
    *Reboot your machine...
    Upon restart your primary HD will not be recognized...
    * you will then be prompted to select your language.
    Once selected
    *Click Utilities/startup... Highlight the the selection that refers to the OS dvd located in the dvd rom drive.
    * Click restart...
    !!!!!!!!!!Be sure to reconnect your Primary HD Before your computer restarts and you hear the chime!!!!!!!!
    If you do not replug your HD before the chime it will not be recognized.
    In that case restart again.
    Upon restart once again
    *Choose your language...
    *Click Utilities / disk utility
    In the left column select and
    *Highlight your HD ...
    Then towards the top portion / center of the page
    *Click the heading Erase
    Then on the page toward the bottom
    *Click security options
    This will then provide erase options.
    I USED THE FIRST OPTION
    "Dont erase data"...
    *click OK
    * click erase...
    Once erased which should take a few seconds
    *Cancel the disk utility...
    * Click Utilities / startup
    And your newly erased HD should now appear in the list.
    * Select your drive from the list by highlighting
    It should no longer have a name.
    *Once selected, you will then be prompted to restart and install the OS to your newly erased HD...
    Thats it!!!!
    Once everything reinstalls re-add your personal info or registration info and you are up and running.
    Goodluck ;)

  • My MacBook Pro 10.6.8 prompted me of a new itunes update this morning, so i downloaded it. Since then itunes has been starting up randomly on its own, and starts playing the first song on the list. I quit itunes, and it keeps reopening.

    My MacBook Pro 10.6.8 prompted me of a new itunes update this morning, so i downloaded it. Since then itunes has been starting up randomly on its own, and starts playing the first song on the list. I pause the song, and it resumes it on its own again. I'm not joking. So, I end up quiting out of itunes; but, it starts right back up again on its own. After quiting out of the app a few times, it eventually stops reopening; however, about an hour later (or less) it opens again. HOW DO I MAKE IT STOP? I'm just about to delete itunes, because I've had enough of this crap. I hope someone can help. I've restarted the laptop, and it seemed like that fixed it, then itunes started up doing the same thing again an hour later. ituneshelper is unchecked; bluetooth is off; i only have speakers and a mouse plugged in (also charger).

    Read this Apple Discussion Thread and possible solutions. The audio jack has been the main culprit, also certain sync and automation settings including connected remotes.

  • Iphone 5 keeps freezing and scrolling on its own

    My iphone keeps freezing and scrolls on its own also it will open up apps at random times. When that happens I lock and unlock the phone to stop the freeze or self scroll. Can someone please help me with this issue

    Shirleen,
    That's very odd! Let's see what we can find out. When did this start happening? Has anything new been added to your device recently? Is your software up to date? Please share a few details so we can assist in finding resolution. Thanks
    TrevorC_VZW
    Follow us on Twitter @VZWSupport
    If my response answered your question please click the �Correct Answer� button under my response. This ensures others can benefit from our conversation. Thanks in advance for your help with this!!

  • HT204053 I put my husbands apple id in when i started to set up icloud, but i really want to use my own.  Now i'm stuck at the point where I'm supposed to tell it what to link and I don't want to link anything, just sign out and restart with my own.  How

    I put my husband's apple id in when I started to set up icloud in error.  I realized I needed to change this right away and tried to sign out and restart with my own apple id, but it won't let me sign out in the middle of setting up.  It says something about if I don't sync documents, all documents will be deleted from this computer, but I don't want to download all his work documents.  Is there any way for me to start over and fix this?

    Having signed out as suggested above, go to http://appleid.apple.com and create a new Apple ID if you don't already have one. You will need a working email address which is different from that in the ID already in use.
    The set up your Mac/device(s) as indicated here:
    http://www.apple.com/icloud/setup/

  • How do I use the commands to start and restart the jmqbroker normally?

    How do I use the commands to start and restart the jmqbroker normally?
    Because I have tried to use "jmqcmd shutdown bkr" and then tried to type
    "jmqbroker" to start up. My screen hangs up and seems that the process
    hangs up. The message is
    [28/Jun/2002:18:29:07 GMT+08:00] [B1060]: Loading persistent data...
    [28/Jun/2002:18:29:08 GMT+08:00] [B1039]: Broker "jmqbroker" ready.
    The prompt is hanged until I press CTRL-C.
    Then I got the following message:
    [28/Jun/2002:18:32:07 GMT+08:00] [B1047]: Shutting down broker...
    [28/Jun/2002:18:32:07 GMT+08:00] [B1077]: Broadcast good-bye to all
    connections ....
    [28/Jun/2002:18:32:07 GMT+08:00] [B1078] Flushing good-bye messages
    [28/Jun/2002:18:32:07 GMT+08:00] [B1056] Cleaning up persistent
    store...
    [28/Jun/2002:18:32:07 GMT+08:00] proceessing 0 messages and cleaning
    up 0 files...
    [28/Jun/2002:18:32:07 GMT+08:00] [B1063] Done
    [28/Jun/2002:18:32:07 GMT+08:00] [B1048]: Shutdown of broker complete.
    Then, I use jmqadmin to invoke the console, I can start the broker
    again, it gives me
    Error encountered while connecting to the broker: "MyBroker":
    Broker Host: 'localhost'
    Primary Port: '7676'
    [C4003]: Error occurred on connection creation, - caught
    javax.jms.JMSException
    Please verify that there is a broker running on the specified host and
    port.
    I used ps -def | grep jmq there is no process anymore.
    Is it a bug? Would somebody have any idea on what went wrong?

    'jmqbroker' is the command to start a broker.
    When you type 'jmqbroker' in a command window,
    unless you put it in the background, the shell
    prompt won't return until the broker is shutdown.
    So when you see 'Broker "jmqbroker" ready.', it tells
    you that the broker is running and is ready.
    When you CTRL-C the process, it has the same effect
    as using jmqcmd to shutdown the broker. And so after that,
    there's no jmq processes running since you have just
    shutdown the broker.
    Remember that the jmqcmd/jmqadmin 'restart' command is to
    restart an already running broker. jmcmd/jmqadmin does
    not support starting a new broker instance.
    If you are using csh, end the jmqcmd command with an ampersand ("&")
    to have the broker running in the background. An alternative is to
    stop the process with Ctrl-Z then input the command "bg" to have that
    process resumed in the background.
    The problem with not being able to start a broker using the
    administration console is a documented limitation of the product that
    Yvonne also mentioned. Check the Administrator's Guide for that.

  • Has anyone Had an iphone start expanding out of its own case. I took it to the apple store and they said that is normal to tell you the battery is bad.

    Has anyone Had an iphone start expanding out of its own case. I took it to the apple store and they said that is normal to tell you the battery is bad.

    We need to know more about your system, please download EtreCheck and run the report and please post it on your next reply. Then we can see how your system is configured, what apps are on it and look for anything obvious. We will look forward to seeing your report.

  • Gateway restarting on its own again and again

    I have an application developed on iPlanet Application Server, integrated with the Portal using URLScraper. I am running the Application through the Gateway. The gateway is restarting on its own time and again and I have to log in again every time. At times the gateway restarts after 5 - 10 mins...At times, it goes on for 2 - 3 hours. Also, even when the gateway does not restart, I am shown the Portal Authentication menu page while working on the application. Apparently, something is happening to the session or to the gateway.
    In iwtSession, I found that a lot of sessions were being created and some were destroyed with 5 -10 minutes of being created, while only 1 person was working on the Portal. Could this be the problem?
    What all could be the reasons why a gateway would restart on its own? I have set the maximum idle time of the session to 30 mins. and the max session time to 800 minutes.

    The session are not set on the gateway but rather on the server. The gateway itself has a session with the server. The gateway restarts if it looses its session with the servers or if something else happens that forces the gateway to restart itself.
    Take a look at the web server error logs to see if the web server is restarting during the time the gateway is restarting. You can see this at /install_dir/netscape/server4/https-hostname/logs
    Also the additional log information that would be usefull here is the iwtGateway, take a look at that, at the time of restart. Make sure ips.debug=message when you look at the log files.
    What version of portal are u using ips sp3a ?

  • MacBook was restarting on its own and now is not powering up. What could cause this and how to troubleshoot?

    MacBook was restarting on its own and now is not powering up. What could cause this and how to troubleshoot?

    When did it happen? After updating/upgrading? or just randomly?
    You can try to perform a SMC reset and resetting the PRAM:
    SMC Reset -> http://support.apple.com/kb/HT3964
    PRAM/NVRAM -> http://support.apple.com/kb/ht1379

Maybe you are looking for

  • How to Create a SAP R/3 system in system configuration

    Hi, i am new to EP Any body tell me how to Create a SAP R/3 system in system configuration.Thanks in advance. Thanks kiran.B

  • One to one mapping in OMBPlus

    Hello, i'm looking for information how to create a mapping from one object (table) to one other object. thanks

  • Wait for commit to finish

    Hello, I am calling a standard function that update some tables and at the end execute a commit work without the wait clause, but right after the execution of the standard function I need to perform some operations that needs all the tables to be upd

  • Required resources are missing.  Can't reinstall CS3

    I had to erase my HD.  When I tried to reinstall CS# I keep getting a message "required resources are missing" I've tried from my DVD and from a fresh file (2.3GB ); no luck.  Please help I tried to confirm the uninstall, but it was no help.

  • Error in FI posting in J1IV

    Dear Sir, I am sending some reject material to vendor. 1. i did returen delivery material document created by MIGO with 122 2. I complete J1IS and post J1IV . but user enter wrong entry in J1IS so-- 1. i cancel perticular excise invoice by J1IS. 2. i