DVD not working but works in Sim

My project was completed in Final Cut and exported in Compressor. Imported all assets into Studio Pro and after setting all required settings, I burned the DVD. The DVD will play for 28:30 then freezes. The simulator works beautiful with viewing all the way through. I have tried completely rebuilding the project twice in studio pro but to no avail I get the same result 28:30. I have another sequence in the same final cut program and that one stops at 5:03. I am running out of time for this project and need to get it out the door.

Where does the final DVD fail? Set top DVD Player? or DVD Player Application on the computer?
Did you try just opening the Video_TS folder with DVD Player Application prior to burning it (i.e. from the hard drive)?
If it works on the computer, but not on a set top player, then you probably have too high a bit rate at the point where it fails. What settings did you use in Compressor? Another possibility is bad media but if you tried it several times and it fails the same place each time, that's not very likely.

Similar Messages

  • CD/DVD Drive only reads DVDS Not CD But the computer reads it as a DVD RW Drive!

    CD/DVD Drive only reads DVDS Not CD But the computer reads it as a DVD RW Drive.the drive door say RW DVD+R DL,Compact Disk Rewritable,Ultraspeed,DVD Multi Recorder.I was Wondering if Windows Loaded the wrong Driver?My Laptop S/N IsCNF62612TZ And P/N Is EZ601UA#ABA And The Front Of My Monitor says Hp Pavilion Dv 1000 Entertainment Notebook PC,And The Service Tag Is dv1738od and the Sticker On The Back Of The monitor say Hp Pavilion dv5- 1235dx Entertainment notebook PC.it Cme Factory With Win xp and when i got it the os was corrupted.i tried to reinstall xp but disk said no hard found.so i booted it up with vista ultimate and then downloaded the drivers and stuff from the here.should i had downloaded the 64 bit set as well?

    della wrote:
    My toshiba tecra a2 can only read DVDs. I cant read any type of cd. Ive tried so many things. My laptop is running on xp service pack 3 with a mat**bleep**a DVD RAm UJ 820s. I can burn/run any type of DVD but cant do anything with cds. Ive tried unistalling the drive and that didnt work. Ive uninstalled the IDE drivers and that didnt work. Nothing seams to work. I cant use recovery cds because there CDS. Please Help!!!!!!!!!
    It's probable that the CD 'side' of the combo drive has failed.  That you cannot boot from the recovery CD is pretty much proof of the failure.  

  • Hi, a dvd got stuck in my mac mini and after looking at solutions online and attempting some not only has the dvd not ejected but my mac wont turn on properly, there is simply a white blank screen, can anyone help me please? thanks

    Hi, a dvd got stuck in my mac mini and after looking at solutions online and attempting some not only has the dvd not ejected but my mac wont turn on properly, there is simply a white blank screen, can anyone help me please? thanks

    Hi Claire, sounds dire, but some things to try...
    Have you done a PRAM reset, CMD+Option+p+r...
    http://support.apple.com/kb/HT1379
    In fact, do 3 in a row, takes a bit of time.
    Intel-based Macs: Resetting the System Management Controller (SMC)...
    http://support.apple.com/kb/HT3964

  • CD/DVDs Not Mounting But Drive is Recognized / SCSI Card Not Seen

    Apologies for this mess in advance, but I thought it was worth seeing if anyone had an idea of what to try on either of these two issues from a system software perspective before I start breaking the computer apart and tinkering with hardware.
    My G4 is the 733 MHz model which first shipped with the SuperDrive. That SuperDrive died years ago and I replaced it with an HP DVD Writer 300n which worked fine up until some version update of 10.4 though I can't recall the specific version. In any case, now the drive will not mount any CD or DVD that I insert, commercially-pressed or otherwise. The eject key on the keyboard functions properly, the tray opens and closes without problem and when a disc is inserted the activity light goes on and the disc spins for a minute and all seems normal, but the disc never appears on the desktop nor in any Finder window. The drive is still recognized in the System Profiler and I've double-checked the CD/DVD settings under System Preferences to verify that nothing is set to ignore there. I suppose it's possible the laser suddenly went bad, but as I said, the symptoms showed up following an update (though it was a while ago and at the time I had no need for a optical drive on this computer so I didn't address it then).
    The second issue I discovered when I attached an external optical drive via the SCSI port I hadn't used in many years. That drive wasn't recognized at all and when I looked in the System Profiler the SCSI card isn't listed under PCI Cards. Is there a generic SCSI card driver I might be missing under OS X or will I need to open up the computer and determine which card I actually have in there?
    Any suggestions would be appreciated and hopefully I've provided enough information to make that possible.

    Hi K Roth, and a warm welcome to the forums!
    I find Optical drives fairly short lived myself, but on the Internal, you might try PatchBurn...
    http://www.patchburn.de/
    Do you have another Mac with Firewire and a good optical drive?
    If so you can boot the Other Mac into Target mode...
    http://docs.info.apple.com/article.html?artnum=58583
    Boot this G4 with the Option key held down, see if the Install Disc in the other Mac shows up as a boot choice.

  • Battery will not charge, but works fine on ac.

    I tried resetting the pmu, and using different ac adapters, but to no avail, sometimes the light on the power supply changes to amber, but the charge on the battery remains zero, any tips? (I press the button on the battery without the ac adapter and it flashes on the first green on the first LED for a few seconds and cuts out over)

    Welcome to the Apple discussions.
    When there are battery issues, typically one of three parts has an issue: the power adapter, the battery itself, or the logic board.
    You can test your logic board using the OS X install DVD that came with your system (it will say in small print AHT Version x.x on it). Insert it, reboot holding the option key down, choose Apple hardware test, and follow directions.
    How many charge/discharge cycles does the battery have on it? You can find this in the Tiger system profiler (click blue apple, about this mac, more info, power, battery information). Apple says a properly maintained battery should retain 80% of it's charge after 300 cycles. The Apple note on battery maintenance is http://www.apple.com/batteries/notebooks.html
    Although different ac adapters didn't fix the problem, I'd assume they were working on other systems, so you've eliminated that as a cause.

  • Images are not loading - but work in Preview mode

    Hi -
    I was wondering if anyone can help me.  I'm kind of new to Dreamweaver and I can't seem to figure this out on my own. 
    I'm using Dreamweaver 8.  I developed a web page based on a template in which everything works perfectly in "Preview" mode on all browsers.  But when I uploaded the files to my remote hosting, the template based images (found in the "images" folder) are not loading on the page. The images that I added to the template myself, found in the same "images" folder ($200,000 in ..., and picture at bottom) are loading.  So some of the images in the images folder are loading some are not.
    I've checked the Images folder on the remote site, and they all seem to be there.  I've also checked for broken links, and I'm not getting any (I don't know if that would help w/ missing images or not, but I'm trying everything I can think of).  I also checked to see if there is a separate CSS style sheet, and there wasn't one supplied with the template (there is some CSS info in the code on the html page).  The image sizes are all small enough as well.  Can anyone help me with this? 
    You can view one of the pages at: http://www.200kin5months.com/squeeze-video.html
    Thank you in advance to anyone who might be able to help!
    Stacey
    PS - I've attached a screenshot from Dreamweaver Preview to show what it is supposed to look like.

    Your Web server is running on an operating system that is case-sensitive. You appear to have uploaded an Images folder, but not an images folder.
    You do not have a file here:
    images/squeeze-video_425x344_r9_c6.jpg
    But you do have a file here:
    Images/squeeze-video_425x344_r9_c6.jpg
    So you'll need to either change all your image/<whatever> links to point to Images/<whatever>, or upload another folder named images.
    Or, if you want to use a single folder, and if your local file system is not case-sensitive, you might be able to do it in DW's file panel. Here is a method that you might use to have all of them in a folder named images.
    BACK UP YOUR SITE FILES
    Rename Images to Foo (allow DW to update links)
    Rename Foo to images (allow DW to update links)
    Upload the images folder and any/all files that DW changed
    Delete the online Images folder
    HTH
    Mark A. Boyd
    Keep-On-Learnin' :-)

  • My Temp Work around for my Outlook Sync with Z10 - Not Ideal but works.

    I like many on this forum was pissed that Outlook Sync was not included with BlackBerry Link.. I was fortunate to transfer all my contacts & calendars from my Old Torch 9810 without a problem. The problem is that I need to sync my calendar and updated contacts on a regular bases. I use Outlook 2010 for all my 1400 contacts and Calendar. There is no way I am going to use any cell phone to update this amount of data. I have owned the Z10 since Tuesday Morning and that afternoon I was ready to take it back and I am a die hard BB user..  My wife has an Iphone 5, nice toy, but wont work for my business..  Seriously considered Android phone, but they also have their issues with the Outlook sync via USB..
    But after 6 Days with the Z10, I must say I love it. .Didn't at first, but once you figure out, it is truly impressive.. Also love the virtual keyboard, very accurate and amazing.. Love the fact that I can have multiple applications running at the same time.. I use web pages that I need for work as an active screen and a button on my home page. 
    While waiting for a 3rd party application to implement this (Campanion Link & Deja Office) or to have BB realize that this is serious and add it in their BB link soon.. Cloud is not an option for me.  
    This is the temporary solution I have right now.
    Option 1:
    1. Wipe off all my Data of my old BB 9810. Make sure lates OS is installed.  Delete all contacts. Sync with Outlook but from PC to Phone Only..  Use BB link to transfer the Contacts and Calendar to the Z10. This will replace any contact you have on the z10..
    Option 2:
    Forward any contacts from your outlook as vcard to your Z10 as email.  Click on the .vcard and it will add to contacts. 
    Again this is a temp soltuion without 3rd party software or Icloud until BB adds this to BB link. 

    Yes it's back! ( and works! ) Thank you Apple!
    Thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you, thank you.
    Sometimes it's just the simple things...
    My world is put back....
    jeff
    ...now if we could just get double clicks on Folders in the Finder to open new windows.....
    <sigh>

  • Mapping not working, but works in debug

    Hi everyone,
    Got a strange problem with a simple mapping. The mapping does a Truncate of the target table and then must insert in that table from a view. The view via a dblink. When I run the mapping in debug everything seem fine, it does what it is meant for. Then I run the same mapping from the design center or in a workflow, it does the truncate table but do not insert any row and return with success (apperently no errors). When run directly from the database it does fine.
    How to find out where is the problem.
    Thanks for you help
    Jacques

    The mapping consist of 4 operators : a constant for the name of the table (the staging tabke) to truncate, a premapping (WB_TRUNCATE_TABLE), a view from the production side via dblink with the data to insert into a staging table.
    a very basic mapping, then of course other mapping will load and transform into a target table(fact table).
    If i run the mapping in debug in owb it does the job and data is inserted into the staging table, when run from the package generated in the db it works fine, but when i run from owb design center or in his processflow (at night) nothing but the truncate gets done.
    By the way this mapping has always worked till I decided to test another view that instead of bringing back all the data from production, it returns a delta instead, so basically just a WHERE CLAUSE was added to the old view.
    Database version 10.2.0.4
    OWB : 10.2.0.4.36
    Hope this helpfull
    Thanks
    Jacques

  • MacBook Pro 2007 battery not recognized, not charging but working

    I recently bought a new battery for my MacBook Pro 2007. As said in the title, it seems to work alright, but it's not recognized by the computer (X in the battery icon), and I don't think it's charging.
    I tried to reset the SMC, no change. Unfortunately, I don't have any other computer to test my battery and my powercord on, to see if it's coming from either one of them. And I don't have an Apple Store around.
    Do you have any suggestions ?

    MacBook, MacBook Pro, MacBook Air: Battery not recognized after being fully drained

  • Importing .p7b certificates using certutil does not work, but work with IE. I need to automatize certificate installation. Help!

    Hello,
    I have to add a trusted certificate authority to XP machines to allow use of mail via OWA.
    There is a domain, but there are too remote machines which are not in the domain (and it's on them I'm experiencing the problem).
    Domain sysdmin sent me the .P7B certificate, which I can load withour problem using import with IE. The certificate is stiored in the Trusted Root Certificate Authorities and it's all ok.
    But I need to automatize the certificate import due to the hifg number of these clients as well as the linbe spped (very slow graphic), so I found the certutil utility.
    I've tried with several commands (like "certutil -f -v -addstore root filename.p7b"  or "certutil -enterprise -f -addstore NTAuth filename.p7b" and several variants), but the utility always said that the certificate is correctly imported, but when checking
    with the MMC console I can't find it (and, by the way, trying to load again results in also being notified that the certificate is already loaded!), so all the stuf does not work.
    What should I do to be able to import the .P7B in Trusted Root Certificate using command line (.bat file, of course)?
    Many thanks in advance for any help!
    Max

    Hi,
    As i can understand you want to import a .p7b file which is a chain of certificates. And certutil is not working.
    I too had the same issue. After searching and thinking the alternatives for hours, got a solution which worked for me. Here is it.
    Get certmgr.exe tool available with MS .net framework tools.
    Try adding this to your batch file
    certmgr -add -all -c "File.p7b" -s -r localMachine Root
    where File.p7b is the file containing certificates. You can replace the name with your file name.
    Check if its working.
    Thanks,
    Reyaz

  • Why my cronjob for primary/standby server not work, but worked at prompt

    I have redhat linux version 5, oracle servers 11gr2.
    I have cronjobs to monitor tablespace usage and alert logs.
    However they not work at the cron job, but if I execute them at the command prompt, it worked.
    What might be the problem?
    example of the cron script:
    Head of the script:
    #!/bin/bash
    . /u01/app/oracle/bin/hydev_env
    MAILTO="dba.com"
    LOG=/u01/app/oracle/dba_cron/out/tablespace_90_full.html
    echo $ORACLE_SID
    sqlplus -S <<-EOF >>/dev/null
    / as sysdba
    Cron job set is like this:
    #------------------------TABLESPACES Check------------------------------------------------------------------------
    0,35 * * * * /u01/app/oracle/dba_cron/scripts/tablespaces_over_90%.sh >/u01/app/oracle/dba_cron/out/tablespaces_over_90%.log > 2>&1
    Vi /var/spool/mail/oracle:
    Has error like this:
    /bin/sh: -c: line 0: syntax error near unexpected token `2'
    /bin/sh: -c: line 0: `/u01/app/oracle/dba_cron/scripts/chk_ora_alert_all.sh >/u01/app/oracle/dba_cron/out/chk_oracle_alert_all.log > 2>&1'
    Any guru help?

    Hello;
    Generally this is an environment issue.
    The script works at the command prompt because when you signed on your user picked the environment settings from a profile, for example .bash_profile.
    A crontab job has no environment. That is why you call hydev_env near the beginning of the script. So something of some things are missing from your env file mostly likely.
    What I do is keep an environment file for each database at a location like this :
    /u01/app/oracle/dba_tool/env ( /u01/app/oracle/dba_tool/env/PRIMARY.env )
    The file PRIMARY.env is <database_name>.env
    What I keep in it is everything I need that a background job like crontab would need :
    ORACLE_BASE=/u01/app/oracle
    ULIMIT=unlimited
    ORACLE_SID=PRIMARY
    ORACLE_HOME=$ORACLE_BASE/product/11.2.0.2
    ORA_NLS33=$ORACLE_HOME/ocommon/nls/admin/data
    LD_LIBRARY_PATH=$ORACLE_HOME/lib:/lib:/usr/lib
    LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/usr/local/lib
    LIBPATH=$LD_LIBRARY_PATH:/usr/lib
    TNS_ADMIN=$ORACLE_HOME/network/admin
    PATH=$ORACLE_HOME/bin:$ORACLE_BASE/dba_tool/bin:/bin:/usr/bin:/usr/ccs/bin:/etc:/usr/sbin:/usr/ucb:$HOME/bin:/usr/bin/X11:/sbin:/usr/lbin:/GNU/bin/make:/u01/app/oracle/dba_tool/bin:/home/oracle/utils/SCRIPTS:/usr/local/bin:.
    export TERM=vt100
    export ORACLE_BASE ORACLE_SID ORACLE_TERM ULIMIT
    export ORACLE_HOME
    export LIBPATH LD_LIBRARY_PATH ORA_NLS33
    export TNS_ADMIN
    export PATH
    export MAILTO=
    Important If you are not sure of a setting on your system type "env" at a Linux prompt while logged on as the user where the script works. Change as needed in your .env file.
    Here a script I call from crontab to check tablespaces
    #!/bin/bash
    if [ "$1" ]
    then DBNAME=$1
    else
    echo "basename $0 : Syntax error : use . quickcheck <DBNAME> "
    exit 1
    fi
    # Set the Environmental variable for the instance
    . /u01/app/oracle/dba_tool/env/${DBNAME}.env
    $ORACLE_HOME/bin/sqlplus /nolog <<EOF
       connect / as sysdba
    @/u01/app/oracle/dba_tool/bin/quickaudit
    EOFNotice how I pass the db name as a parameter to the script so I can use the script with several database without changing it.
    /u01/app/oracle/dba_tool/bin/quickcheck.sh PRIMARY
    The crontab to make this run daily at 5:12 am is :
    12 05 * * * /u01/app/oracle/dba_tool/bin/quickcheck.sh PRIMARY > /tmp/quickcheck.out
    Best Regards
    mseberg

  • Finger print not unlocking but works with iTunes and Apple Store

    So I have been battling this same issue since last week. I cannot unlock my phone with the FP scan but it will work when using the iTunes store or Apple Store app. Is there a setting I am missing?

    Hello bdallas99,
    Congratulations on your iPhone 5s, and thank you for the details of the issue you are experiencing when using Touch ID.  I recommend following the steps below for an issue like this (steps 2 and 3 specifically stand out to me for the situation you described):
    Troubleshooting Touch ID
    Ensure that your fingers and the Home button are clean and dry.*
    Note: Cover the Home button completely. Don't tap too quickly, don't press down hard, and don't move your finger while Touch ID is scanning.
    Tap Settings > General > Passcode & Fingerprint > Fingerprints and verify:
    Passcode Unlock or iTunes & App Store is enabled.
    One or more fingerprints have been enrolled.
    If one finger isn't working, tap Edit in Settings > General > Passcode & Fingerprint > Fingerprints > Edit to delete and then reenroll the finger.
    If that finger still isn't working, try enrolling a different finger.
    If you are unable to enroll any of your fingers, take your iPhone 5s to an Apple Retail Store, Apple Authorized Service Provider, or contact AppleCare for further assistance.
    Find the full article here:
    iPhone 5s: Using Touch ID
    http://support.apple.com/kb/HT5883
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • Windows 7 not genuine, but work since I purchased the laptop.

    I owned my t61 for 6 months without a problem, this morning I wake up turn it on and a small window states my copy of Windows 7 is counterfeit.  So I can Microsoft, they stating I need the PRODUCT KEY and buy a new one for $199, + tax.  I think this is just a scam with Microsoft. 
    I email the seller and he provided me with a Product key, so I call Microsoft back and now they tell my the Product Key is not valid and I still need to purchase and new Product Key.
    Now I have to either downgrade to Vista, if I can get the CD's from Lenovo or go back to XP.
    Anything I can do to or say to Microsoft get keep 7 alive on my laptop.
    SGB

    njdjh2o wrote:
    I owned my t61 for 6 months without a problem, this morning I wake up turn it on and a small window states my copy of Windows 7 is counterfeit.  So I can Microsoft, they stating I need the PRODUCT KEY and buy a new one for $199, + tax.  I think this is just a scam with Microsoft. 
    It is an issue between you and the seller of the T61, as Lenevo has never supplied Windows 7 for a T61.
    It appears that the seller has installed a copy of Win 7 using a key that was likely obtained at a too good to be true price from an eBay auction (or some similiar source).  There are reports all over the Web of eBay sellers auctioing Technet or MSDN keys for Microsoft products in breach of the End User Licence Agreements for those keys.  Microsoft later cancels those keys when it detects they are being used in breach of the relevant EULA that Microsoft supplied them under.
    It is a SCAM, but not by Microsoft, so talk to the seller of your T61.
    Cheers,
    Bill
    I don't work for Lenovo

  • Says "did not respond", but works with test servers...

    Hi all,
    This one is driving me crazy! I recently bought an iSight camera and I'm now wanting to get it working with iChat and AIM. I'm behind a Linux firewall of my own construction (ClarkConnect / Fedora based) and at first I couldn't get it to connect to anything, with repeated errors saying that I "did not respond". However, after doing a lot of reading, I've opened up all of the required ports on the firewall and I can happily connect to the 'appleu3test01, 02, 03' servers.
    However, attempting to connect to a PC running AIM brings back the "did not respond" error, and no amount of firewall twiddling seems to make it work. I've connected my Mac directly to the cable modem and this is the only way it will connect, and I've tried connecting to two different PCs in different locations. If I try to connect to a PC with AIM on my local network, there's no problem - I'm straight on - but going through the firewall just doesn't play.
    I've also tried the trick of port-forwarding ports 16384-16403 to my Mac, but still no luck. Not tried connecting to a remote Mac with iChat yet, just because I'm the only person I know with all the right kit...
    If anyone could lend their expertise I would really appreciate it - and so would my blood pressure! ;o)
    Thanks in advance,
    Andy.

    Hi Zephyr,
    With iChat launcged go to the iChat menu.
    Log out of AIM
    Go to the Preferences in the same menu.
    Go to Accounts
    Slect the AIm acount in question in the left hand list.
    Now Click the Server Settings tab on the right.
    This list the main connection port near the top but under the tabs.
    Change this from port 5190 to prot 443.
    Log back into AIM
    Reason.
    iChat logs on to AIM on port 5190.
    It also uses Port 5190 to Group chat, send file and pics.
    It does this over two interent Portocols
    Now some modems need to be port forwarded on ports above a threshold of 1024.
    Some go further and want Protocols listed.
    Of those a small number will not let you Port Forward two protocols on the same port.
    So moving the Login and basic text chat stuff to port 443 (a secure port below 1024) the problem is avoided.
    9:10 PM Saturday; March 11, 2006

  • Wi-fi on iMac not working, but works on other laptops

    Hi there,
    I've recently moved back home with my new iMac, and when I went to try to set up wi-fi on it for the first time, it didn't work. I received a message that "Wi-fi has the self-assigned IP address ____ and will not be able to connect to the internet.". I don't understand why it's not working when I'm currently typing this from my macbook pro which connects perfectly fine, as well as my iPhone, and my parents laptops as well. The wi-fi worked perfectly fine at my old placres
    I've tried resetting my modem and router, restarting my computer, turning wi-fi on and off, deleting the keychain access for the network, and tons of other suggested solutions but to no avail. I also just tried manually imputting my IP and that told me it connected, but the network icon still showed an exclamation mark, and I wasn't able to load any websites.
    Needless to say, I'm extremely frustrated about this, and nothing seems to work. Are there any other solutions I can try? I really don't know what would be causing this.

    When you see an exclamation point in the Wi-Fi menu, from the menu bar, select
     ▹ System Preferences... ▹ Network
    Click the Assist me button and select Assistant. Follow the prompts. You may get a warning that Wi-Fi is not available, that you're too far from the base station, or that you're using the wrong password.
    Assuming that you've ruled out those possibilities, click the lock icon in the lower left corner of the preference pane and authenticate, if necessary. From the Location menu at the top of the window, select Edit Locations. A sheet will drop down. Click the plus-sign button to create a new location. Give it any name you want. In the new location, set up the Wi-Fi service with the same settings you used before. Click Apply and test.

Maybe you are looking for