E 71 - navigation button light blinks every 5 seco...

Is it a bug or a feature? The center light around the five way navigation button goes on every 5 seconds. Is this normal? Can I stop it?

of course you can ! the feature is called "breathing light"
menu > tools > options > modes => when you personalize your mode you have an option called "breathing light" or something like that (my phone is in french sorry !). it is the 9th option of the list, just after "vibrate".

Similar Messages

Satellite A300-1IW: HDD access light blinks every seconds

Hello everyone, and sorry for the english, I'm french :)
I bought a Satellite A300-1IW few days ago and suddently (didn't remember exactly when) the HDD access light start to blink every seconds and it continues even after several reboots!
It only does this with Vista; I checked the disk activity with "diskmon" and I saw that even if there were *no* *disk* *writing* *or* *reading* the led continued blinking, so I think it's not related to some vista services (superfetch, indexing...)
I saw on a Microsoft support a similar problem but it was under windows 98 and with old motherborads!
see : Link: [http://support.microsoft.com/kb/138598]
It seems so that it's related to Vista SCSI or DVD quering...
I now that's not critical but it's annoying to have this led blinking all the time
Have any idea? Do you think it could be related to the bios? I want to be sure before touching this because it's always delicate.
Thanks for your help

In my opinion nobody must offer any comment because you already given the answer. This is nothing unusual and definitely no reason for panic.
What to do about it? What you want to do? Sorry but it is really stupid question. I can just offer you one stupid answer. ;) Take some black adhesive tape and cower the LED. ;)

Laptop Won't Boot. Caps Lock Button Light Blinking

I just bought a HP Pavilion DM4-2015dx laptop a few days ago. Turning it on this morning, it won't boot and the Caps Lock light is blinking. I have searched the HP site and Google for a solution to the problem and have found nothing to tell me what the blinking light means or why it won't boot up. Does anyone have an idea of what the blinking light on the Caps Button means?

My laptop HP pavilion Dv6 - 7132TX had a problem of blank screen and caps lock key blinking. I bought the laptop on 28th Apr 2012 and just before completing a year, I was facing a problem of computer inadvertently not booting. It used to show black screen with wifi LED red, power button LED glowing, and caps lock key LED blinking. http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&docname=c01443366 On going to the above link, I tried to notice the number of blinks of caps lock key LED.Found that the blink count was an endless loop of 2 LED blinks. On checking in the above link, found that 2 blinks meant the problem was BIOS corruption failure. LEDs blink 2 times BIOSBIOS corruption failure(as found in the table in the above link) So I went on and found another link to find the BIOS upgrade on the same page , where it read, Step 3: Find and download BIOS updates Then followed to the link: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?swlinkmsg=100&cc=us&dlc=en&docname=c00042629&lc=en&product=4057208 to download the driver. Downloaded the BIOS latest driver and installed it. It gave the same problem while restarting the laptop which was required to complete the bios installation. Link for the BIOS installation: http://ftp.hp.com/pub/softpaq/sp54501-55000/sp54629.exe However after several force shutdowns and reboots (since in my laptop the blank screen during bootup was inadvertent and random..) the installation could proceed and complete. After that voila.. Problem gone Hopefully it stays that way. Now next task on my mind is to fix the sleeping problem of my PC and the noise problem of the speakers. 1.Laptop does not sleep and goes into freeze mode with LEDS glowing and screen black.2.While the laptop speakers are on, they constantly make some background noise as if the speakers have a loose connection. However I got a clue that the problem is not with the connections but with the frequencies mismatch. Inherent problem of laptop architecture I suppose. However still wish to hear sounds clearly on my laptop. Had a good experience with HP with my earlier laptop from HP. However now things are changing I guess. Feel good that I could at least troubleshoot and save money. [Even gas is Rs. 84 per litre.] and more importantly time since I was working when I saw this problem and did not want to keep laptop powered on All the time just to avoid restart .

E71 navigation button blinking problem.

navigation button light blinks every 8 seconds. its consuming my battery. can i stop it?
Solved!
Go to Solution.

Yes ... there are a couple of features that could be making it blink, as follows:
1. It could be notifying you of certain events (such as missed call, texts etc) ... Tools --> Settings --> General --> Personalisation --> Notification light
or
2. You might have the "breathing light" enabled (as it is by default). This is set for each profile - for example, you'll find it her for the General profile ... Tools --> Profile --> General --> Personalise --> Breathing light
By turning off the "Breathing light", I think this will also give you a non-lit digital clock as your screen saver afte your time-out period.
Hope this helps.
My previous phones:
6310i --> SE K750i --> E50 --> E61i --> E71
... much prefer the Nokia phones, especially the E71

TDP-XP2 yellow lamp light blinking periodlcally

I have replaced the lamp in a TDP-XP2. The projector powers up and then the lamp light blinks every 15 seconds or so. The lamp does not come one. Any ideas on what the problem might be?

davidyoung98 wrote:
I bought the 65HM167 around October 2007 and it has been an awesome TV - the best I've ever had by far. However, about a year ago (early to mid 2012) the lamp finally went out. The old lamp was shattered inside the housing, but the outer glass was not broken.
I ordered a new Toshiba lamp and installed it. Shortly after installing the new lamp, white dots began to appear on the screen. I read that this is not an uncommon problem and tends to be an issue with the DLP chip - it's probably going out. So the number of dots went from three to maybe ten over the course of a couple of months.
One day late last year I turned the TV on, the blue light came on and I could hear the TV try to start (as usual). However, this time it didn't come on - it tried to restart something like eight times. After that a voice came out of the TV speaker saying "lamp not working" (which scared the c*** out of me, by the way), and the red light with blinking yellow light stayed on.
I've tried restarting the TV multiple times, but the yellow and red lights keep coming back on. The voice only intermittently announces that the lamp is not working. I've removed the lamp and inspected it, but unlike the shattered first lamp, this one still appears intact.
So is this really a lamp problem, or is the DLP chip fried and somehow preventing the light from coming on? I REALLY don't want to spend any more money on this TV unless it's likely to fix the problem for the next few years, so I'm reluctant to hire a repairman.
Any suggestions?
Unplug the set and it will reset. I have the same problem, sometimes I have to unplug it several times for it to work. Your bulb is probably an aftermarket bulb(same as I have). I've had this problem for 3 years, picture is fine when it goes on. I actually put the set on a power strip, and just hit the button to remove it from the power for 10-15 seconds.

Isight camera green light blink

My isight camera green light blinks every two seconds, when I try to use facetime or any other application of isight. And of course, the camera is not working.
I'm using a Macbook Pro, just bought it a month ago.
Does anyone have the same problem or have a way to solve this annoying issue?

Xiunei wrote:...Macbook Pro, just bought it a month ago.
Does anyone ... have a way to solve this annoying issue?
Yes. Your retailer does. He can either: (1) determine whether your new Mac needs repair or replacement, or (2) show you how to make your camera work correctly.

HP vs17x monitor power light blinking

After I bring my computer out of standby mode my vs17x monitor's power button/light blinks blue, with the sound of what I assume is power going to the speakers, and continues unless I hold it down to turn it off or unplug it.
After some waiting and clicking I can get it back to normal, but as far as I know it's just random clicks that bring it back up
Any diagnosis/suggestions?
Thanks
-Update-
-This morning I was able to get my screen back up by pressing the power button on my compaq keyboard (crescent moon, which puts in standby/brings up standby/shutdown/restart menu)
Also all the icons on my desk were rearranged, put to the left/top, but I'm unsure if that was due to my random clicking
-This afternoon I after walking away for a bit (after I turned it on) the screen came back up
Message Edited by J_Winn on 10-15-2009 03:52 AM
Message Edited by J_Winn on 10-15-2009 12:48 PM
This question was solved.
View Solution.

Thanks so much for the hint, J_Winn.
Once, I opened the unit, I could see that three of the capacitors looked different the tops were bulging ( bulging capacitor ).
I replaced those three and all was well.
Disassembly hints:
- The curved plastic top piece of the pedestal stand pops to allow access to the 3rd pedestal screw.
- The entire pedestal assembly then slides toward the bottom.
- Use a small flathead screwdriver to pop off the front cover. (but not tiny, that was my initial problem)
- Write the colours of the four wire pairs in pencil on the metal screen so you remember which goes where.
- Remove the small metal cover from the larger metal cover to access the ribbon cable connector.
- To disconnect the ribbon cable from the circuit board, carefully pry up the black strip on the connector.
Reassembly:
- The power button cover, bottom of the U points to the back of the case.
- The other button cover piece has tabs that fit into the small switch circuit board
Hope this helps!

Incoming call: camera flash light blinking

Hi,
After i completed "Reset All Settings" on my iPhone 4S (iOS 5.0.1), i then always get camera flash light blinking every time i receive the incoming call. I want to turn this off by trying Setting --> General --> Accessibility --> LED Flash for Alerts (turn off), however, it does not work for me. i still get the LED flash blinking everytime i get the incoming call and this is very annoying.
Could you please advise how to get this fixed?
Thank,
sanlen

Hi,
I tried it but it did not work for me. Any further advise please.
Thank,
sanlen

HT2693 I purchased Huawei Dongle and trying to connect with my NEW MacBook Pro (OS- Mountain Lion) USB port 3.0 but unfortunately it does not support. When I plugged in my the power is flowing in dongle due green light blinking twice in every 3 sec but no

Hi,
I purchased Huawei Dongle and trying to connect with my new MacBook Pro (OS- Mountain Lion) USB port 3.0 but unfortunately it does not support.
When I plugged in my macbook the power is flowing in dongle due green light blinking twice in every 3 sec but no connection found or diver shown.
Please let me know how I have to use it. I got some suggestion for USB hub 2.0 but It does not make any sense and driver installation.
So please suggest proper direction to use it and provide link to install any driver.
Thanks
Tauheed Ahmad

Yes Clinton I did same, but they were (Huawei customer support) surprised about this problem, They behave like they have no idea about USB 2.0 and 3.0 knowledge. They handsUp that reason I posted my problem in this forum.
So is there any better solution to use any mediator between these USB version handling, Please let me know.
Thanks
Tauheed

Add navigation buttons on top of every scene

Hello,
I've got a Flash movie with quite a few scenes and I'd like to add navigation buttons (prev\next) with AS3 to move from scene to scene.
Sounds easy but...
If I write this on first frame of first scene :
this.addChild(play_btn);
buttons will appear OK on this first scene but will disappear under objects of the second scene
If I change to
stage.addChild(play_btn);
button will appear OK over every scene but, as my SWF is loaded in an e-learning software that produces SWF, the buttons will remain on the "stage" of every slide of the final module ! I can't remove them when the user changes slide because I can't run AS3 when changing slide...
Is there way of adding the buttons "inside" my movie but on top of everything that might appear afterwards ? No more depth or Z order in AS3 ?
Thanks.
Please don't tell me using scenes is bad because I've been using them for years and I've always read that all scenes become a long timeline at runtime. They're just very handy to me.

I believe in AS1/2 you can set a depth at any value.
Yes ! And that would have been handy here... not clean, but handy !
Here's what I did so far :
I added the buttons to the root and found a function that did the trick, called with a timer :
var play_btn:mcBtnPlay = new mcBtnPlay();
Object(root).addChild(play_btn);
function moveToTop(child:DisplayObject):void {
(child.parent != null) ? child.parent.setChildIndex(child, child.parent.numChildren-1) : null;
function timerListener(e:TimerEvent):void {
moveToTop(play_btn);
The only problem is that the buttons will flash on screen at scene change because the of the timer interval, but you can think it's on purpose (visual clue) .
Don't know if there's a more clever way to detect scene change apart from some code on each first frame of scenes ?

My Curve 9220 has a black screen and the LED light blinks red every 5 seconds

The phone won't come on and the light blinks red. I dont know what to do

Hi there,
If you have a good battery or the batttery is good enough then try those steps , it may help :
( Credit JSanders )
1) Make sure you have Blackberry Desktop Manager installed. BlackBerry desktop software
2) On your PC, go to Start > Run and copy and paste the following line exactly (meaning with the quotation marks):
"c:\program files\common files\research in motion\apploader\loader.exe" /nojvm
3) The Application Loader Wizard will appear -- click "Next."
4) In the "Connection:" drop-down menu, you should see "USB-PIN: UNKNOWN". Click the "Next" button.
5) You should then see a list of applications ready to be installed for your Blackberry. Hit Next and Finish and you are well on your way to getting your Blackberry back to life. Congrats! Just don't disconnect anything and let the lengthy process finish completely.
NOTE: If you do not see a list of applications mentioned in step 5 and instead see the message "The Blackberry Desktop Software does not have Blackberry Device Software for the device that you have connected to the computer. Contact your wireless service provider or system administrator," then you must download Blackberry's Operating System for your carrier and device. BlackBerry Software Download Site
Just select the appropriate carrier and network type, select your Blackberry model from the list and download the latest version. Install this download and follow the above steps again and you should be on the right path.
Good luck.
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

Solid green light with blink every 5 seconds

I use this shuffle on my windows xp pc. When it was time to charge the (first gen) shuffle, I connected it to powered USB, as usual. After plugging it in I got a solid green light with a blink every 5 seconds. I then tried plugging it into the wall adapter charger with the same outcome. I left it overnight to charge and upon checking the battery, it's still red/orange.
Does anyone have an idea what could be the problem?
Thanks

Does this mean I have to buy a new one, or is the
battery replacable? I haven't even owned it for a
full year.
Take it to an Apple Store... they'll replace it.

HT201836 AppleTV light blinks when plugged in. Unable to restart with menu/down buttons.

AppleTV light blinks as apposed to continuously on. Unable to restart using down/menu button. Apple logo however is on the screen!

Apple TV (2nd and 3rd generation): Restoring your Apple TV - Apple Support
This is generally the resolve to those symptoms.

Why are these lights blinking, on button, red light removal, won't print,

I have a HP photosmart C6280 All-in-one. Periodically the on button blinks, the red eye reduction and a button
on thePhoto Express panel, it will not print when those buttons are blinking. How do I fix this problem?

Hi,
This fix is for many HP printers, it may also applicable for your pinter too.
Regards,
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Blackberry Notebook -- Red light STEADY, Green light BLINKS 5 TIMES, wont come on

Ive charged my Playbook for 30 minutes via computer. I tried cutting on the tablet and the red light came on STEADY, then the GREEN LIGHT BLINKED 5 times. It would not power on. I also tried cutting it on while plugged in and the same thing occured. I have tried resetting it by holding the + and - sign for 20 secs and no success. I bought the playbook from Radio Shack NEW in February. Any suggestions?

You can Try this and let us know wich solution works...
If your battery is dead or near dead, you have a problem. If you follow these instructions you may be able to make a recovery but it will take some time.
The charger is controlled by software. The software will not run because the battery voltage is too low. When the battery is too low and you turn on the PB, It will only run for about 4 minutes and then shut down again. During this 4 minutes, the charger will begin charging but since the battery voltage is still too low, the unit will shut down again and the charger will shut off.
To get the voltage up sufficiently for the PB To continue, you have to have the charger plugged in and every 5 minutes or so, you have to hold the power button on until the red light flashes then release it.It will once again recharge for 4 minutes. You may have to repeat these steps at least 10 times. Once the voltage gets up a bit, the charger should stay on but it will takes 6 hours to fully recharge the battery. When your charger is charging, it will feel warm to the touch so check it often to see if it is in fact charging.

E 71 - navigation button light blinks every 5 seco...

Similar Messages

Maybe you are looking for