E70 new firware - cure for the Linux USB storage b...

As anybody who've tried the usb-storage mode on linux knows, E70 usb storage support is buggy. (See http://joker.iki.fi/cms/?q=node/265&PHPSESSID=682710e65e04be1fc87b2c8bce1688c3 - though the patch mentioned there hasn't found its way to the mainline kernel afaict). Apparently E70 reports false device size to the usb host, and causes a bunch of these errors:
[75974.362000] end_request: I/O error, dev sda, sector 3910520
[75974.362000] Buffer I/O error on device sda, logical block 488815
Does anybody know if the new firmware takes care of this?

Possibly. I upgraded from 2.6.16, where I saw all these problems. So perhaps it was fixed ( or rather, worked-around ! ) in 2.6.17.
When I plugin and select data transfer mode on the phone I see :-
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver ub
Vendor: Model: Rev:
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 121049 512-byte hdwr sectors (62 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 121049 512-byte hdwr sectors (62 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
sda: unknown partition table
sd 0:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete
And then :-
# mount /dev/sda /mnt
# ls /mnt
Backup Documents Others private Sheets sys Videos
data Images Presentations resource Sounds System
Oh, I have upgraded the phones firmware. I have 2.0618.07.10 31-08-06 RM-10", but I did upgrade before my kernel update.

Similar Messages

  • Are there DASYLAB 6.00.07 hardware drivers for the NI USB-9215

    I'm working with Dasylab 6.00.07. Do you know whether there are allready any hardwaredrivers for the NI USB-9215 ?

    At this time, DASYLab only works with NI hardware via the traditional NI-DAQ interface. Any board that is not supported via NI-DAQ will not work with DASYLab V8.
    The data sheet for the USB-9215 says:
    USB-9211 and USB-9215 devices each come with a ready-to-run
    data logger application that acquires and logs up to four channels of
    analog data. For more functionality, the NI-DAQmx Base driver
    software is a multiplatform driver with a limited NI-DAQmx
    programming interface.
    This says that it is not supported via NI-DAQ, and is not currently supported by DASYLab.
    We are actively working to ensure DASYLab's support for the DAQmx interface - watch for updates of the software!
    Please note that new driver support, such as this,
    will require an upgrade to the released version of DASYLab. It is not possible to update V7 or earlier with the changes required to fully support DAQmx.
    - cj
    Measurement Computing (MCC) has free technical support. Visit www.mccdaq.com and click on the "Support" tab for all support options, including DASYLab.

  • Simulated device capability for the NI USB-6008

     I noticed that Nidaq 8.3, does not have simulated device
    capability for the NI USB-6008.  Is there any way of simulating
    this device?
    Thanks

    Hello mmac,
    Unfortunately, there is no way to simulate the USB-6008.  If you would like to see this functionality in a future revision of NI-DAQmx, I would encourage you to go to the Product Suggestion Center and submit a product suggestion.  R&D considers these suggestions when deciding on new features for development. 
    Best regards,

  • Proble while creating new Data Connection for the Webservice

    Hai All,
    when creating a new Data Conneciotn for the Webservice in the interactive form i got the following errror
    Cannot choose this operation:
    - there is no associated SOAP Binding
    edit -> new Data Connection -> WSDL -> i entered the wsdl url -> i got the methods in that webservice
    but when i select one of the method in the methods list i got above error
    i developed a webservice in NWDS and deployed the WAS ( created a webservice for the session bean)
    please help me to solve the problem
    Thanks in advance
    Siva Sankar N

    Problem was solved,
    Downloading the WSDLs:
    Download the 3 WSDL files from the WAS using the WS-navigator tool:
    Go to http://<was-host>:50000/wsnavigator/enterwsdl.html
    Select your WS
    Click in the menu “WSDLs”
    Download the default SAP WSDL
    You will have 3 WSDL files in the downloaded zip files.
    1) main.wsdl
    2)config1_XXXXVi_document.wsdl
    3_configl_document.wsdl
    Perform the follwing task to the above wsdl files, and use this wsdl files to the datasource
    1. Copy/paste the <wsdl:service> XML element from the main.wsdl to the Config1_SDN_adobeWSVi_document.wsdl.
    2. Copy the <wsdl:binding> XML element from the Config1_document.wsdl to the Config1_SDN_adobeWSVi_document.wsdl.
    3. Add the SOAP namespace (xmlns:soap="http://schemas.xmlsoap.org/wsdl/soap/") from the main.wsdl to the Config1_SDN_adobeWSVi_document.wsdl.
    4. Adjust the namespace reference by replacing “prt0” and “bns0” with “tns”.

  • Need help locating a wallet case for an Xperia T2 Ultra Smartphone that has a slot on the side for the mini-usb

    I realize this board is for Xperia tablets, but I don't see a board for Xperia Smartphones.  I do hope someone here can help. I have a Sony Xperia T2 Ultra smartphone.  I love the phone, but I purchased a case for it not realizing that the case doesn't have a slot on the side for the mini-usb connector, which means that I have to charge the phone with the case open.
    I called Sony accessories, and they don't seem to make a case with a slot on the side.  They have a very nice case, but again, it doesn't have the correct opening for the charger and you have to charge the phone with the case open.
    I have also searched several websites for such a case with no luck.
    Does anyone here know where I can find a wallet-style case for the Sony Xperia T2 Ultra with a magnetic closure (or some way of securing the case closed) that will actually allow me to charge the phone while the case is closed?  Please let me know.

    This is the only "question" I could extract out of your confusing post:
    "I want to know if it even can be done in Flash or would we need to use something else like PHP or Javascript?"
    It can`t be done in Flash alone you need php.
    With the experience level you already admitted to, I strongly advise to stay away from such a project, you will save you and our customer a lot of headaches, no offense.

  • I just bought the new HDMI cord for the IPad, it works good but a small potion of the TOP and the BOTTOM is cut off. It doesn't seem to do it for movies. My monitor is a 23 IN' acer s series.

    I just bought the new HDMI cord for the IPad, it works good but a small potion of the TOP and the BOTTOM is cut off. It doesn't seem to do it for movies(although I can't really tell. My monitor is a 23 IN' acer s series. I just installed the drivers for my monitor with no change. I think I have a CD somewhere for my monitor maybe it has some kind of program in there that can help me. I can post a picture if I need to. Thanks

    No work around that I know of.
    Apple Feedback http://www.apple.com/feedback/

  • Does anyone have a cure for the following error running on Windows, "The procedure entry point sqlite3_wal_checkpoint could not be found located in the dynamic link library SQLite.dll.

    Does anyone have a cure for the following error running on Windows, "The procedure entry point sqlite3_wal_checkpoint could not be found located in the dynamic link library SQLite.dll.

    I have searched my computer for that file SQlite3.dll and also file QTCF.dll and I cannot find either one when I search my whole computer for it.  I cannot fix this!  I deleted Itunes and every time I try to download it, it goes through all this download till the end when it says that iTunes.exe-entry point now found and that Procedure entry point message comes up.  HELP!  This is driving me crazy.  How can I get itunes to work again when I can't find the danged .dll file to remove, move or rename!?!?!??

  • How is it possible for me to turn in my old iPhone 4s for the new iphone 5 for the lowest price

    how is it possible for me to turn in my old iPhone 4s for the new iphone 5 for the lowest price

    You would have to sell your iPhone 4S for cash to then buy the iPhone 5.
    http://gizmodo.com/5934778/where-to-sell-your-iphone-4s-for-the-most-money

  • I have bought new iPad air for the new app I book apple charged 1$. On the web sit it's say free .

    I have bought new iPad air for the new app I book apple charged 1$. On the web sit it's say free .

    If you have recently created a new iTunes account, the $1 charge will most likely be for account verification. The money will be refunded shortly.
    http://support.apple.com/kb/HT3702

  • Create new CBO statistics for the tables

    Dear All,
    I am facing bad performance in server.In SM50 I see that the read and delete process at table D010LINC takes
    a longer time.how to  create new CBO statistics for the tables D010TAB and D010INC.  Please suggest.
    Regards,
    Kumar

    Hi,
    I am facing problem in when save/activating  any problem ,so sap has told me to create new CBO statistics for the tables D010TAB and D010INC
    Now as you have suggest when tx db20
    Table D010LINC
    there error comes  Table D010LINC does not exist in the ABAP Dictionary
    Table D010TAB
         Statistics are current (|Changes| < 50 %)
    New Method           C
    New Sample Size
    Old Method           C                       Date                 10.03.2010
    Old Sample Size                              Time                 07:39:37
    Old Number                51,104,357         Deviation Old -> New       0  %
    New Number                51,168,679         Deviation New -> Old       0  %
    Inserted Rows                160,770         Percentage Too Old         0  %
    Changed Rows                       0         Percentage Too Old         0  %
    Deleted Rows                  96,448         Percentage Too New         0  %
    Use                  O
    Active Flag          P
    Analysis Method      C
    Sample Size
    Please suggest
    Regards,
    Kumar

  • How to create new text symbols for the standard program.

    Based on the customer's requirement, I need to create a new implicit enhancement for the selection screen.
    I want to create new text symbols for the parameters and blocks, but I cannot change the standard ones.
    Does anybody know something about that? Thank you.

    hi ming yu,
    example : %_MATNR_%_APP_%-TEXT -> this is the material  description name in mb5b
    change the description in ur enhancement implementation
    %_MATNR_%_APP_%-TEXT = 'Material'
    it is works only input/output field
    Thanks&Regards,
    naveen

  • Create new depreciation class for the existing asset

    Dear Experts,
    Please explain step by step:
    1. How to create a new depreciation class for the existing asset
    2. How to make a asset transfer to the new asset in the new asset class?
    Thank you in advance

    Hi,
    The pre-requsit of creating a new assets clause :-
    1. Co. code assigned to Chart of Dep.
    2. Dep areas have been defined
    3. GL account no. is not more than 8 digit.
    The transfer of an assets within the same co code can be done thru T.code ABUMN.
    Award if helpful
    Sunil

  • Is 4.3.3 the new updated software for the iphone 3gs?

    is 4.3.3 the new updated software for the iphone 3gs?

    No.  The post you responded to is nearly 7 months old.  At the time, 4.3.3 was the most current version for the 3GS.  As of now, 5.0.1 is the most current version for the 3GS.

  • Do I need a new case number for the Transfer of License Form? I am the recipient of a transfer of li

      Do I need a new case number for the Transfer of License Form? I am the recipient of a transfer of license product registration. The transferring person has already filled out and returned the transfer of license form. Do I use the same number or do I need a new number.

    You need to get a new number for yourself because the transferor and the recipient cannot use the same number.
    Reference: I chatted with an Adobe agent, and that was the response they gave me.

  • USB Recording - requirements for the external USB drive

    What are the requirements for the external USB drive to be recognised by the TV?
    I've tried two now, which can both be seen by the TV to show media, but neither are recognised by the TV to be used as USB Recording space.

    Hi,
    I have a similar question.
    I have a 40L6353 and I cannot seem to playback anything recorded onto USB.
    I have tried a large 500 Gb Toshiba (USB powered) drive and 2 or 3 others such as an 8 Gb SanDisk and a smaller capacity non branded 500 Mb stick.
    All of the above I have formatted in the TV. When I press record the pop-up staes that recording has started and when I press stop it asks me to confirm. When I go to the recorded list it shows the files but says that they are an unsupported file format!!
    I can play videos and music transferred to another Toshiba 500 Gb drive by PC.
    I have also tested the sticks and they pass the 2 on-screen tests and I believe when a stick is inserted I can pause live TV.
    Does anyone have any ideas?
    I have been trying to get this to work for over a week - if there is a fault I will need to go back to the vendor but I want to be sure it isn't operator error.
    Thanks in advance.
    Message was edited by: banzai

Maybe you are looking for

  • Problem in compilation of EJBHome object

    hi I have created a remote interface,HOmeinterface ,a primary key class and a bean. The package structure is as follows: sampleEJB->remote interface sampleEJB->Home interface a similar directory structure for both bean as welas primary key class file

  • Want to make a bootable disk, but...

    Recently survived a minor nightmare of "losing" my hard drive.  With disk warrior managed to get back in business.  But I realized I really need a way to boot up from a backup.  I'd prefer to use a thumb drive.  I have Super Duper (supposedly bootabl

  • Dbms_lob and line size problem

    Hi, below is a simple function which returns a CLOB. When I call this function from sqlplus and spool the result in a file via the SPOOL command I get a line break after 80 characters. When I replace in the function the CLOB type with a VARCHAR2 type

  • Apple TV not showing up in Display options

    I have a 3rd generation Apple TV and a 2012 Mac Mini.  As far as I can tell this should work and it did work before I upgraded to Yosemite (today was the first time since then that I tried to connect the two).  As you can see, no Devices are Detected

  • Color management in hp 8500 officejet premier pro so I can use Lightroom or Photoshop?

    When I print what I see on the Monitor is not what I get on printout.   I don't seen to be able to use the icc profile in either application.  If I let the printer manage the color, they are blue-green overtone.