Easy Set UP...help with settings.

Hello.... If you can help me set up EASY SETUP correctly you'll be my hero!
Hi, I'm using FCE and 3 different types of footage and cannot get the settings right;   exported files are tiny, have big letter boxes, etc
Here are the files and types:
#1:
Dimentions: 1920 x 1080
Apple Intermediate Codec, Linear PCM
ColorProfile    HD (1-1-1)
Bit rate:   86,137
#2   (kodak zi6)
Dimentions 1280 x 720
Codecs   H.264,ACC
Bit rate, 9,489
#3
.MPEG-4
640 x 480
Codecs   MPEG-4, AAC
Bit rate:   6,242
Now...how do I get this thing going to make it work?   (I understand I have different qualities of video..but it's for YOUTUBE so it doesn't have to be cinema ready.   Just good.
Also...do I need to create a new project? I've done a decent amount of editing and hate the thought of re-doing all of the searching through the files to find the right parts, etc.
Thanks very much in advance.
Brad in Denver

Dunno. Never opened FCE.
Upon ingest, you convert your H.264 and MPEG4 to ProResLT. Set your sequence to ProResLT. The NTSC-sized stuff will be a problem.
Your AIC is not a good idea at all unless you know what to do with it and why you have it. In that case, you want everything converted to AIC and use an AIC sequence.
bogiesan

Similar Messages

Nokia 2710 plugged in Mac. Help with settings,plea...

Nokia 2710 plugged in Mac. help with settings,please?
When I plug Nokia 2710 in USB in Mac computer OSX 10.6.4, I see 3 options:
1. PC suite
2.Print &media
3. Data storage
My questions are about option 1. PC suite.
When I select it, I can see in Network Preferences
2 icons for Nokia phone:
Nokia 2710c
and
Nokia 2711
and on the Network Preferences pane there are options to configure them with options to set telephone number,account name and password.
(My Nokia 2710 is connected and works with mobile phone network Virgin in Australia)
How exactly to set these configurations and how to use them?
And which one to configure - Nokia 2710c or Nokia 2711?
Thank you in advance for any practical advise!

@JuliaAU
Although your 2710 Navigator is a S40 device, here are two resources for you:
http://www.nokia.co.uk/support/download-software/device-as-a-modem/connect-to-your-mac/connect-via-u...
http://klauskjeldsen.dk/setup-internet-connection-via-bluetooth-using-nokia-6300-on-mac-os-x/
Probably would try 2710c first and watch out for any capitalisation in VirginInternet
Something at the back of my memory suggests that you may need to create a new location in Network Preferences but I maybe wrong here.
Happy to have helped forum with a Support Ratio = 42.5

Ipod Nano 6th generation setting issue - hi, when i am listening music and the screen goes to sleep my music stop playing.Please help with settings

hi, when i am listening music and the screen goes to sleep my music stop playing.Please help with settings

No problem. And no worries, several people have made this same mistake!
Either way enjoy the iPod!
Brock

Need help with settings for my broadband.

when I first started with BT, I set up some time limits for my broadband usage so that my teenage children were not using the internet late at night but I now would like to change the times and I cannot find out how to do this?
Please can anyone help.
Currently my internet goes off at 11pm at night and on at 7am.

You can edit or delete the settings you already set.
Settings are under BT access Control in the hub manager.
Click on Apply to save any changes you make.
http://bt.custhelp.com/app/answers/detail/a_id/11364/c/346,1887,1891

Help with settings on Mem Dividers K8N Diamond Plus

I am Trying to figure out what the exact setting differences would be on the memory dividers for this board. I have good memory that will run about as high as 275bus (ddr550 speeds maybe a bit more @ 2.5-3-3-8) TCCD based @ 2.65vdimm and my CPU can do 3ghz on water with HTT @300 x10.
The mem divider settings are as follows.
1/2
2/3
5/6
5/4
1/1
I understand the 1/1 as that is simple. But (sorry for the noob questions here) what is the formulation or mhz or % settings for the others. I would like to be able to calculate them please. Any help would be great here Thanks ahead of time
Also on my list of learning is the HTT/LDT. Ive seen the settings in what looks to be 200,400,600,800,1000. There are 3 different places. is their a specific one I need to change to get my LDT/HTT down in the 1000 and under range. Do I have to change all 3? also the 16 up and 16down what do they do prospectively as well for this and is it a setting I should worry about? I'm new to some overclocking read about all the guides here and abroad posted on line. But for some reason not many go into the details of what settings are what. I used to be on a K8N Neo2 Platinum and not the same settings there as on this board. So its like a new learning curve.
Again Thanks for all and any help you can give to a new guy here at the MSI forums and somewhat new to overclocking.
Firefighter
PS the rig is I am using is in my Sig.

Welcome
You can download this little utility to calculate divider speeds..
http://www.geocities.com/edgemeal_software/Files/AMD_Calc_v1.0.07.zip
Some info about the HT settings can be found here. I don't have an exact answer about what the link widths do, someone else might be able to answer that question for you.
https://forum-en.msi.com/index.php?topic=104009.0
More info on overclocking can be found in the forum stickies as well..
https://forum-en.msi.com/index.php?board=27.0
edit: The amd calc shows memory freq instead of dividers. The 166 divider would be the same as 5/6 in the bios, the 133 divider would be the same as 2/3 etc... basically the bios shows it as fractions of the htt or fsb speed. As an example with the fsb at 200mhz and the memory set to 5/6 would yield a ram speed of 166mhz. Using the 5/4 divider would run the ram at a higher speed than the fsb..I hope this makes some sense to you :D

Need help with settings for Xbox360

Real quick, I need to know how to set the router for 2 xbox360's with open nat...I have looked all over and have done the MTU and UPnP tricks but want to do port triggering but am not sure how to set applications or static IP...if needed. Thanks for all the help.

A known issue with Linksys routers is the NAT Type 3 or anything related to dropping of Internet connectivity during play time. Network Address Translation (NAT) is the ability of a router or firewall to translate a public IP address to a private IP address and vice versa. It adds security to the network by keeping the private IP addresses hidden from the outside world.
Here is the link for setting up the Xbox 360: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=082ee344b4754044b1ff95fcd78b5305_4576.xml&pid=80&r...

Can someone help with settings on WRT54G on a bridged modem?

I have a motorola 2210 modem, and I know that in order for you to bridge it, you have to go to 192.168.1.254 and change the PPP settings. Now, can someone who ahs done this walk me throught the modem and router setup in order of what they did. I just tried it, and I ended having to reset my router and my modem because i massively screwed up and lost my internet connection. I tried linksys and I didnt get much, and I tried att and they wouldnt help because of the router. I just need the exact steps to do this.

For Converting the Modem into the Bridge Mode...Check this link.
After converting the modem into the bridge mode,you need to configure the linksys router with PPPoE settings..Check this link.

MOVED: Help with settings on Mem Dividers K8N Diamond Plus

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=104329.0

Welcome
You can download this little utility to calculate divider speeds..
http://www.geocities.com/edgemeal_software/Files/AMD_Calc_v1.0.07.zip
Some info about the HT settings can be found here. I don't have an exact answer about what the link widths do, someone else might be able to answer that question for you.
https://forum-en.msi.com/index.php?topic=104009.0
More info on overclocking can be found in the forum stickies as well..
https://forum-en.msi.com/index.php?board=27.0
edit: The amd calc shows memory freq instead of dividers. The 166 divider would be the same as 5/6 in the bios, the 133 divider would be the same as 2/3 etc... basically the bios shows it as fractions of the htt or fsb speed. As an example with the fsb at 200mhz and the memory set to 5/6 would yield a ram speed of 166mhz. Using the 5/4 divider would run the ram at a higher speed than the fsb..I hope this makes some sense to you :D

I-mate K-JAM and Nokia E61 Help with settings

Hi,
I used to be able to conect to my works exchange server with my i-mate. I can not seem to get it right with the Nokia. Could view my e-mails and sync my calender with the i-mate.
Settings in the sync function of the i-mate:
Server configuration
Server address - [email protected]
This server requires an encrypted (SLL) conection
User name
Password
Domain
This would then uatomatically sync my calender and e-mail
Can one do the same with an Nokia E61?

I have a K-Jam and love the heck out of it!! I've had several HTC products and found that this has been the best yet. No problems. I highly recommend it.
As for getting it setup with my iBook, that's been a bit of a pain. I can't seem to figure out how to dial to GPRS. Did you accomplish this with your 910? If so, how????? I've got the iBook and K-Jam paired, and it sees it as a bluetooth modem, but I can't figure out how to setup my t-mobile. Any comments would be great!
Thanks,
Tom tom(at)thenielsennet(dot)com

Adding two Airport Express to New Ariport Extreme - need help with settings

First, I have a brand new Airport Extreme (square N one) that is up and working just fine. The SSID is "Unstable Network". Under the Wireless tab...The Wireless mode is currently: "Create a Wireless Network". The "Allow this network to be Extended" box is not checked. Radio Mode is "Automatic". Radio Channel Selection is set to "Automatic". What do these need to be changed to?
2nd: I have an older Aiport Express that I used to use for itunes and a receiver. I want to add this to my Airport Extreme Network to extend the wireless network to the basement and stream itunes to my remote receiver. I can see this Airport Express using Airport Utility. The SSID of this Airport Express is "Unstable Network Extender". Under the wireless tab....Wireless mode is set to "Join a Wireless Network" The network it is assigned to is my Airport Extreme SSID "Unstable Network". It shows up as IP address 10.0.1.6. What should these setting be to both extend the network and allow itunes to stream?
3rd: I have a second Airport Express that I would like to plug in at a remote end of my house on the second floor to extend my network even further. It is currently hardwired and I can see it in Airport Utility. The SSID is "Unstable Network Extender 2". The setting are the same as the other Airport Express. It shows up as IP address 10.0.1.13. What should they be to extend the network.
Thank you in advance to anyone that can clearly spell out what my setting should be. I am non-technical for the most part, but was technical enough to set up my Airport Extreme but can't figure out how to extend everything.

Since you will have a mix (802.11g/802.11n) AirPorts, and that you want to "daisy" chain the two AirPort Express Base Stations (AX) to extend the wireless network, you will need to configure the three of them for a static Wireless Distribution System (WDS).
Here are the basic steps to do so:
(Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete. In this case, I suggest that you temporarily connect both AXs to the 802.11n AirPort Extreme Base Station (AEBSn) by Ethernet. Also, jot down the AirPort IDs (MAC addresses) for each of the base stations to be used in the WDS. The AirPort ID and is printed on the label on the bottom/side of the base station.) Finally, I strongly suggest that you perform a "hard" reset on the AEBSn and "factory default" resets on the AXs to get them back to their original "out-of-the-box" configurations before you start.)
For reference in this setup:
o AEBSn = main base station
o AX#1 = relay base station
o AX#2 = remote base station
Main Base Station Setup - AEBSn
o On the Mac click the AirPort status menu in the menu bar and choose the wireless network created by AEBSn.
o Open AirPort Utility (located in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the AEBSn, and then, choose Manual Setup from the Base Station menu.
o Click Wireless in the toolbar, and then, choose “Participate in a WDS network” from the Wireless Mode pop-up menu. (Note: You may have to hold down the <Option> key before making this selection to get the WDS option.)
o Click WDS, and then, choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
o Click the Add "+" button and enter the AirPort ID of the relay base station - AX#1.
o Click Update to send the new settings to the base stations in the WDS.
Relay Base Station Setup - AX#1
o In the AirPort Utility select AX#1, and then, choose Manual Setup from the Base Station menu.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the AEBSn from the Channel pop-up menu.
o Click WDS and choose “WDS relay” from the WDS Mode pop-up menu.
o Enter the AirPort ID of the AEBSn in the Main AirPort ID field.
o Click the Add "+" button and enter the AirPort ID of AX#2.
o Click Update to transfer the new WDS settings to the relay and remote base stations.
Remote Base Station Setup - AX#2
o In the AirPort Utility select AX#2, and then, choose Manual Setup from the Base Station menu.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the AEBSn from the Channel pop-up menu.
o Click WDS and choose “WDS remote” from the pop-up menu.
o Enter the AirPort ID of the AEBSn in the WDS Main field.
o Click Update to transfer the settings to the base station.
(ref: Pages 42-46 of "Designing AirPort Networks.)

Need help with settings....

My podcast was pulled for some reason from iTunes and they have told me to resubmit it but before I do I have to do this:
Change the title and link fields of your RSS feed to something other than what they are now.
Please can someone tell me what that means please, my feed is:
http://feeds2.feedburner.com/TheRadioTronPodcast

Presumably you submitted a feed file to Feedburner? - if so you should be able to amend that; also it would be much better to submit the file directly to iTunes rather than getting Feedburner to do it.
The feed itself has no line returns; although this does not affect its validity it makes it almost impossible to read. FeedValidator says the feed is valid but throws up some minor errors; in particular the 'description' tag should not contain HTML (the links). I also noticed that though the mp3 file appears to be correctly referenced the duration is given as zero. However the feed can be subscribed to in iTunes using the 'Advanced' menu.
In order to make the changes iTunes suggested you will need either to edit the feed file directlily or use whatever program you used to create it to make the changes. This page shows you a basic feed file and may help you to understand the process:
http://www.wilmut.org.uk/pc

Help with settings / tips for ratoc fr1sx firewire - scsi adapter

I'm hooking up a Quantum DLT 7000 using the ratoc firewire to scsi adapter and I think a few people on this board have been through the process, which I've read can be a bit of a hassle.
I was hoping soemoine might be able to share what settings ultimately worked for them on the fr1 utility or any other tips they may have for using this kind of setup.
thanks

Sorry Scott - you're not getting the responses for this at all... I don't use a Ratoc adapter, but have considered it. I do recall Trai talking about this particular adapter some time ago now, and the fact that the slightly older driver was more reliable than the newer version. Whether or not that situation has since changed I can't say.
The error message you are getting might indeed be referring to the driver for the Ratoc adapter - is there an older driver available on their website at all?
You might try contacting Trai directly to see if he can shed some light on this - as far as I know the adapter isn't widely used, although some folk must be using it, I'd have thought.
A final thought is to see if you can find someone who has a DLT drive connected to a G4 or 5 and ask them if they can read the tape back in to verify the info is written to it correctly. My guess is the Ratoc driver writes out fine, but struggles to import it all back in...
Good luck!

Creating a score set - please help- I'm going crazy

OK- deep breath ...........I'm trying to create a score set for 4 instruments. I read the manual, then tried everything on p 765........... I started first with the tracks in the Arrange area.- with and without rubber bands - and because this didn't work, I scrubbed this and tried to simply set up thew score in the Score Editor.
It didn't work. I want to be able to see the music for 4 instruments - at one go -in the score editor. Is this possible ?
Please someone save my sanity and give me an blow- by- blow account how to achieve this. I've been on this for hours and can't see the wood for the trees now so am going out for a breath of fresh air.
Kay.

You can look at the bottom of the arrange page.. But for 4 tracks I would open a score editor window by itself.. The score section is complex and not intuitive to say the least..
In the score editor, click on the 6th from the left box. it looks like a page of text (when you highlite it will turn blue).. That shows you the whole score, in a tradional page format.. If you still see only one track, double click somewhere other than the track, (space in between). Page will toggle between showing one track/ and all tracks..
To make life easier if you have many tracks to display = create a 'score set'. Label it, (band etc). reduce the size, 50 - 65% whatever. Then go under File in Logic, page set up.. Select the 90 turn, so now the pages longer side to side. You can see more measures at a time..
You may want to have several score sets, to help with editing. One of everything. another to show just the piano and guitar, etc. This will make it easier to edit, copy paste between staves etc.
The score editor is very powerful, if you take the time to figure it out, but documentation is vague

'Easy Set-up' Option - Problem with edit canvas/windows - really need help!

Hello Everyone. . .
Have a problem that i really need help with, i have tried so many different things to sort this - but with no sucess.
I usually work in High Definition and i have recently done a small project for someone in DV. When changing to work in DV, i selected the DV setup from the 'Easy Setup' menu. I have now changed back to HD and there are a few things different with Final Cut that i can't shift!
When i move a clip from the capture bin into the edit window, the clip no longer fills that window like it always used to and there are lines at the top and the bottom of the clip - almost like it is in widescreen.
Editing like this wasn't too much of a problem, but when i came to compress and do a final render of the whole film - there was the same black lines on the top and bottom of the film.
I can't figure out how to get the setting back to how they were, and have the clips fill the edit windows and fix the end render/compress.
Any ideas from anyone on what i am experiancing with all this? And. . . how to fix this problem?
Any help on all this will be very much appreciated!

Hello Everyone. . .
Have a problem that i really need help with, i have tried so many different things to sort this - but with no sucess.
I usually work in High Definition and i have recently done a small project for someone in DV. When changing to work in DV, i selected the DV setup from the 'Easy Setup' menu. I have now changed back to HD and there are a few things different with Final Cut that i can't shift!
When i move a clip from the capture bin into the edit window, the clip no longer fills that window like it always used to and there are lines at the top and the bottom of the clip - almost like it is in widescreen.
Editing like this wasn't too much of a problem, but when i came to compress and do a final render of the whole film - there was the same black lines on the top and bottom of the film.
I can't figure out how to get the setting back to how they were, and have the clips fill the edit windows and fix the end render/compress.
Any ideas from anyone on what i am experiancing with all this? And. . . how to fix this problem?
Any help on all this will be very much appreciated!

I am trying to set up a friends new iPad but am struggling with settings for her email accounts can anyone help me

can someone help with the email settings for the email accounts on this iPad.? Or tell me what you would expect the default settings to be. currently we mail is a virgin.net account

Please see: http://help.virginmedia.com/system/selfservice.controller?CMD=VIEW_ARTICLE&ARTIC LE_ID=2979&CURRENT_CMD=SEARCH&CONFIGURATION=1001&PARTITION_ID=1&USERTYPE=1&LANGU AGE=en&COUNTY=us&VM_CUSTOMER_TYPE=Cable for details.
Regards,
Steve

Easy Set UP...help with settings.

Similar Messages

Maybe you are looking for