Edit Analytics Properity Issue

Hi Experts,
In OBIEE 11.1.1.6.0,
First issue:
I click "Edit Analytics Properity" in answer and select "compountView!2" from 'View for Text Delivery' area.
When I sent this report into user who remain receive the "compountView!1" layout report. It is very odd.
I look at the help document, which said "Use this box to manually control which compound layout, including its associated views, is sent to a particular destination"
Are you facing the same issues?

Hi,
Use the below links to unlock the locked Object
http://host:port/rep/support/public/LockAdminService
http://host:port/dir/support/public/LockAdminService
While using the above link , you would have to give your Uid and pwd, then you can observe the check box which is locked object, then check the box and click on above button.Remove lock
Regards
Chilla..
Points rewarded if it is helpful..

Similar Messages

Oracle Database Express Edition 10g Download Issue

Hi everyone. I just downloaded the freeware Oracle Database Express Edition without any apparent problems. However, when I attempt to go to the Express Edition Homepage, which is location http://127.0.0.1:8080/apex,
I get the message that my Internet Explorer cannot display the webpage. (It can, however, display other pages.) I cannot understand why this is the case since I successfully added Web site 127.0.0.1 in my Control Panel (as specified in the instructions.) Also, the instructions stated that HTTP port 8080 was the default port, unless my system said that this was not available (which it did not.) I also tried rebooting, which did not make a difference. Help!
Thanks,
Jason

user13176791 wrote:
Hi everyone. I just downloaded the freeware Oracle Database Express Edition without any apparent problems. However, when I attempt to go to the Express Edition Homepage, which is location http://127.0.0.1:8080/apex,
I get the message that my Internet Explorer cannot display the webpage. (It can, however, display other pages.) I cannot understand why this is the case since I successfully added Web site 127.0.0.1 in my Control Panel (as specified in the instructions.) Also, the instructions stated that HTTP port 8080 was the default port, unless my system said that this was not available (which it did not.) I also tried rebooting, which did not make a difference. Help!There is a forum dedicated to Express Edition, in which we have discussed a lot of the variants in failure that causes this problem. At the top of the page you are reading, there should be links like "Forum Home » Database » Database - General". The middle one will get you to a list of all Oracle forums and after the first 5, the rest are alphabetical - XE is pretty far down that page.
(You might also note that there is an Installation forum next to this one. That might be better suited to the task than the 'catch-all' general forum.)
The most common issues are related to not preparing the operating system properly. For example, if you use a laptop you probably use DHCP to get a different address from the various sites you connect to. However, Oracle works as a server and depends on having a well known address. In fact, it tends to bind the IP address at install into it's configuration files. Therefore it is critical to use the loopback adapter in such situations.
Other issues are dependent on the actual OS into which you install. For example, Ubuntu (Linux) has very differnet install philosophy as Red Hat / Fedora, and requires a different install technique. Then again, on Windows, it is nearly impossible to install anything Oracle on a Windows 'Home' OS, and XE generally has not even been tested against Windows 7.
Other common reasons include anti-virus; firewall; not having appropriate operating system level permissions; in Windows - using a Domain-based userid instead of a local administrator; and just general finger issues.
Express is considerably different in the install behaviour and runtime behaviour. For example. it uses RPM and MSI instead of Oracle Universal Installer. It does not include Java in the database, which limits a lot of functionality. And it uses the built-in PL/SQL Web Gateway instead of any external HTTP server. As a result, it can be quite a shock to mmany of the regular inhabitants in this forum.
I strongly encourage reading the documentation for XE. In particular, reading the install doc. Start at http://tahiti.oracle.com and look for the Oracle Database 10g Release 2 Express Edition documentation. (Just below the Oracle Database 10g Release 2 documentation.)
G'luk

Why don't PS Elements 12 edited photos properly save in version sets after editing?

This is a problem that never occurred in PS Elements 11. But if I edite a photo that is currently in Organizer with PS Element Editor and save it after editing, it only gets properly included in Organizer and made part of the version set about 20% of the time. The rest of the time the edited file gets saved in the same folder as the original but has not been added to Organizer. The appropriate check boxes in the Save As screen are checked. But 4 out of 5 times it behaves as if the boxes are not checked. I have done several photos in sequence and used the same exact keystrokes and only one or two will be included in the version set. I then have to go "Get" the version and bring it into Organizer and tell the program to Stack the two photos. It is a pain to do it that way. Does anybody have a clue why it is not working as it is suppose to?

Known bug in converted catalogs. It works correctly if you create a new catalog or a workaround for converted catalogs is to kill the ElementsAutoAnalyzer.exe process in Task Manager.
Cheers,
Neale
Insanity is hereditary, you get it from your children
If this post or another user's post resolves the original issue, please mark the posts as correct and/or helpful accordingly. This helps other users with similar trouble get answers to their questions quicker. Thanks.

Persona Q Premium Edition pre-order issue

Hi,
I pre-ordered 2 copies of Persona Q Premium Edition, but when I view the product page for it in my order history, it shows me the description for the standard edition. It's the same issue many other people are having. I'm wanting to know what can be done about this issue.
Thanks

Hi nubtarts,
When this title was initially made available for pre-order on BestBuy.com, the standard edition was incorrectly listed as the Wild Cards edition. The SKU number was correct though, and our merchant team has since made sure SKU #7377002 properly reflects the standard edition online.
I've sent you some additional information, so please make sure to check your private messages when you can. To check your PMs, simply sign into the forum and then click on the letter icon in the upper right-hand corner of the page.
Thanks for reserving your copies of Persona Q: Shadow of the Labyrinth with us!
Aaron|Social Media Specialist | Best Buy® Corporate
Private Message

Solaris 10 Dev. Edition - Network config issue (NIC,DHCP,Can't ping router)

I am a developer getting started with Solaris 10 configuration. I recently installed Solaris 10 and have run into an issue with network connectivity.
I have done much research on this and I was able to get communiction to the internet established once, but the settings were lost on reboot.
Overview - The Solaris box is connected to a router which is acting as a DHCP server.
AMD 64 dual 2.6
nForce4+ integrated NIC
1) I am not able to obtain an address from the router. Nor do I get a respons back when I ping it. I get an IP etc if I boot into Windows so phyicial connectivity is fine.
2) Upon reboot the device nfo0 as shown using ifconfig -a has an IP of 0.0.0.0.
3) If I run ifconfig [hostname] my machine gets the ip from the hosts file, but I would like to obtain this from the router.
4) NOTE - the machine shows as active on my router, but the Solaris box cannot be reached from other computers on the networ, nor do I get a reply back when pinging the router from the Solaris box.
GOAL - reach and obtain a DHCP from the router and have the changes stick upon reboot.
/etc/hosts contents
127.0.0.1 localhost loghost
192.168.1.55 solarisX /*<-- this is what I get when I do ifconfig nfo0 solarisX */
/etc/hosname.nfo0
netmask + 255.255.255.0
solarisX
/etc/defaultrouter
192.168.1.254
/et c/netmasks
192.168.0.0 255.255.2550
Specific Steps taken:
Using the driver nfo-2.4.5 locate at http://homepage2.nifty.com/mrym3/taiyodo/eng/ I did the following.
% cd /.../nfo-x.x.x
% rm obj Makefile
% ln -s Makefile.${KARCH}_${COMPILER} Makefile
% ln -s ${KARCH} obj
where ${KARCH} is the result of `isainfo -n`, and ${COMPILER} is
"gcc" or "suncc" which you want to use to make the driver.
4. Testing
Testing before installation is strongly recommended.
# cd /.../nfo-x.x.x
# /usr/ccs/bin/make install
# ./adddrv.sh
# /usr/ccs/bin/make uninstall (for solaris7, don't remove the file )
# modload obj/nfo
# devfsadm -i nfo (for solaris7, use drvconfig and reboot with -r )
# ifconfig nfoN plumb ( where N is an instance number, typcally 0 for first card)
# ifconfig -a ( you will see an entry for nfoN)
# ifconfig nfoN YOUR-HOST-NAME
# ifconfig nfoN ( ensure IP address is correct)
# ifconfig nfoN up ( and then you can test with ping, telnet, ftp ...)
5. Installation
After you ensure that the nfo driver is fully functional, install it.
(1) copy the nfo driver into the kernel directory
# cd /.../nfo-x.x.x
# /usr/ccs/bin/make install
If you do not test the nfo driver yet, execute the following commands:
# ./adddrv.sh
# devfsadm -i nfo (for solaris7, use drvconfig and reboot with -r)
(2) Configure the network interface. Create and/or modify the following file:
/etc/hostname.nfoN
(3) Reboot the system.
# init 6
Edited by: hedger on Nov 16, 2007 11:17 PM

Thanks Alan. I worked on trying to get the NIC working again last night. I had it working once, although the settings did not perist. I can still get the device to load, but I can't communciate with the router (it's not physical because another OS can reach it.
I took your advice and tried the sys-unconfig. But I did not have much success.
I am wondering if plopping in a new PCI NIC would be the most efficient route to get the server up.
What kind of NIC do you utilize and have had success with?
I am looking at possibly a DLINK DFE-530 or NetGear FA-311. I don't need wireless at this point just a rock solid DEV box.
Thanks again for the previous info.
Ted

HR Analytics Headcount issue

Hi,
We have a requirement in HR analytics. monthly snapshot table will take future headcount in a month based on effective start date but if users running report today report should only show headcount where hire date<sysdate.
ex: previous month head count =100
this month company hiring two employee where emp1 joined may 10 and emp2 will join on may 25
OOTB report will show headcount=100+2=102
users expecting headcount=100+1=101(because emp2 not yet joined)
how can I fix this problem in informatica mapping. I need to customize mapping with above logic. any idea?
Thanks
Jay.

The monthly snapshot calculation is based on the start dates and this is calculated in the PLP process. The best option may be to get a more granular report that uses the HR_WRKFCT_EVT_F table and not the MONTH snapshot. You may have to edit the report so that you are querying the base fact versus the month table. Hope this helps.

ALV GRID edit mode keyboard issue

Hi,
I have created a program that displays an ALV GRID.
From the Layout I said to edit in edit mode the ALV Grid.
In the menu toolbar I exclude the button 'cut - copy -paste and delete line'.
When I run the program I see that these buttons are not displayed --> OK.
BUT my problem is: if I use the keyboard then the ALV Grid manages these actions.
For instance. I select some lines and press the key DELETE on the keyboard --> the lines are removed and that is not that I expect because I removed this action from the toolbar.
For the cut - copy and paste it's the same.
Do you have a solution for me --> intercept an event or change the function keys or ....
I would like that the ALV Grid does not manage the keys delete, CRTL-C, CRTL-V in edit mode.
Thanks,
Stevie,

Hi Steve
I was not aware of this. So, I recommend you to try this:
At the event "before_user_command" you can terminate the process by resetting the ALV user command.
e.g.
 CASE e_ucomm .
 WHEN '&INFO' .
 CALL METHOD gr_alvgrid->set_user_command
 EXPORTING i_ucomm = space.
 ENDCASE .
This code within the event overrides the '&INFO' function and terminates its process. For cut and copy, you can find out ucomm values by putting a break point inside the event and tracing the value of "i_ucomm".
For some relevant issues, you can inspect the tutorial <a href="https://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/documents/a1-8-4/an%20easy%20reference%20for%20alv%20grid%20control.pdf">"An Easy Reference For ALV Grid Control"</a>.
As another thing, since you are a new SDN member, you are welcome and let me introduce you the SDN forums pointing system: You can assign points to posts you find helpful while solving your question. You can reward points by clicking the yellow star icon at header of each reply post. You can reward;
- one 10 points (solved)
- two 6 points (very helpful answer)
- many 2 points (helpful answer)
Kind regards...
*--Serdar

Server 2012 Standard Edition network teaming issue at bootup

I have a Windows server 2012 x64 standard edition server (not R2) using two Intel I210AT nic's on an ASUS P9D-X motherboard. They are setup in a team using the Microsoft teaming. No special options, latest updates and the latest Intel drivers.
The team is setup in switch independent mode and connected with quality cat6 cables to a Cisco 3600 switch. No special options on the ports of the switches, no LACP or trunking, just standard unconfigured ports.
The problem we have is when the server is rebooted the team will not communicate with the network. If we unplug one network cable communication begins. We can then plug the cable back in and both
ports work and communicate normally.
This issue is serious as it requires physical action on every restart.
We have tried deleting the team and recreating it and we get the same results. Is there some specific change that needs to be made to make this work or is this possibly a known bug?

May be problem on Cisco side, Cisco is very clever, could assessed network traffic as a problem and close the port. When OS is running, then NIC Teaming working fine, but when you boot up server, "BIOS not running with NIC Teaming", in this moment
may occur problem on Cisco side.
I recommend, if you use Cisco, configure NIC Teaming in LACP mode and configure your two ports on Cisco to LACP, it's better way.
Regards,
thennet
Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable. This helps the community, keeps the forums tidy, and recognises useful contributions. Thank you!

Editing Cells - Simple Issue, but Confused

Simple issue, but I can't seem to figure this one out in Numbers. I'll do my best to explain in words here.
Let's say I store the following dollar amount in cell A1 = 1264. The number is formatted to dollars. Therefore A1 is presented as $1,264.00. All is well up to this point.
Okay, now let's assume I click out of the cell completely. Now let's say I wanted to add $250.50 to this amount in cell A1. When I go to the formula bar to add in the $250.50 it's requiring me to remove the dollar sign and comma out of my $1,264.00 number in order to complete the computation. Is this normal? I never had to do this in Excel. My thought was that I should only need to include an equal sign at the beginning of the formula (in other words, there shouldn't be a need to remove the dollar sign and comma every time, right?).
Just wanted to make sure that I'm not missing anything overly simple (which I'm sure I am).
Any help is greatly appreciated! I'm really enjoying my trial version of Numbers thus far.
Message was edited by: randy.humes

Randy,
There is another way to remove each comma and dollar sign, one that will work on multiple cell at once if needed. Select the cells that you want to clean-up and using the Cells Inspector, change the format from Currency to Number and then click the Thousands Separator checkbox to deselect it. Then all that remains is to add the equal sign when you go in to edit the content by changing your input to a formula. Then if you still want the value to be displayed as currency, change the format back.
I'm not saying that this method is better, but may be worth a try if your are backspace/delete averse.
Jerry

Photoshop Elements 10 Costco special edition a scanner issue

I downloaded the new software as directed. However, I lost the ability to import directly from my Canon scanner/printer.
My old Photoshop Elements 6 allowed me to do that through ScanGear. Is there a way to scan directly into
Elements 10 without having it go to I-photo or desktop? When I selected Photoshop Elements 10 as a destination, it didn't
end up there. With this big upgrade in features, there has to be a way. I have done all the disconnecting printer, deleting it and reinstalling it. Opened the help menu and followed it but it didn't help. What is weird, I can print from Elements 10 so it recognizes the Canon as a printer but not a scanner. Any suggestions?

I just uninstalled PSE10. I couldn't see where there was actually an application for PSE10 in the application folder. All I had was a file (4k). That is why PSE editor didn't accept any photos or allow me a way to get photos to it when I tried to set up the editor preference. My system is probably messed up after trying for two days to upgrade software for the Canon printer, the twain I had was too old and it couldn't get upgraded. I have two I-Mac one in Az. and one in Wa. Both are about the same age and have printer/scanners about 3 years old. If I have the twain issue with both computers because of the new PSE software, I need to buy new ones which will not justify keeping PSE10. Everything I tried through your diligent return of emails failed. I am puzzled, as I never have had any problems with your software. I love it. I have used it for collages (Scrapper's Guide and my own creations, etc.) I have restored old photos, made cards. I have 20 thousand photos on my Mac. in Wa. and I have never had an issue dragging a photo into Elements 6. I was looking forward to your new features. I guess I am not mentally ready for the installation issues anymore. You don't suppose there is a problem because it is a special Costco edition. I never got that far. Two pictures dragged into your program and now it has an operational error... nothing went into it... no import.
Do you ever get to sleep? You have long hours.

Captivate 5 SCORM 2004 3rd Edition ADL Testing Issues

I have published a project from Adobe Captivate 5 and am currently trying to get it through the Advanced Distributed Learning (ADL) Sharable Content Object Reference Model (SCORM) 2004 3rd Edition Conformance Test Suite. I was able to pass the first part: the Content Package Conformance Test and solve the initial errors I was experiencing. However, I now have a new set of errors relating to the Sharable Content Object (SCO) Run-Time Environment (RTE) Conformance Utility Test. It appears that they all stem from:
ERROR: The Terminate() method was never successfully called.
Here is the detailed SCO test log:
Attempting to Launch SCO C:\Documents and Settings\Administrator\Desktop\offender_transportation6\offender_transportation.html
Commit("") has been called
ERROR: The Communication Session is NOT initialized
ERROR: The SCO called the API methods out of order
ERROR: Commit Before Initialization
Terminate("") has been called
ERROR: The Communication Session is NOT initialized
ERROR: An invalid Terminate() call was made
ERROR: The SCO called the API methods out of order
ERROR: Termination Before Initialization
ERROR: The Terminate() method was never successfully called
ERROR: The SCO is SCO RTE 1.0 Non-conformant
The project is currently set to issue a completion status to the LMS after 22 slides have been viewed. Then the project should output the Quiz Results and Slide Views to the LMS. For Project End Options I have tried both: Stop Project and End Project. I haven't been able to find any other settings in Adobe Captivate that relate to this Terminate problem.
Can anyone give me some insight into what could be causing this error?

As I tested, Captivate really cannot support 3rd Edition.
I'm not sure what's the differences between 2nd and 3rd
Edition, but I found that Articulate's '09 series (
http://www.articulate.com/products/quizmaker-publishing.php)
outputs these two editions separately.
I hope Capative could update the module to treat 3rd
specially.
William Peterson
eLearning Master
http://www.sameshow.com/blog/

Editable SALV Dropdown issue

Hi Gurus, in WebDynpro for ABAP, I have a SALV based editable table in which lot of columns have dropdowns (Drop down by Index) and by default system is creating a roundtrip to the server whenever I make a selection in the drop down. Whenever data to be maintained is large this creates performance issues and times out. I want to suppress the roundtrip created during the selection in the dropdown.
Even I tried with Dropdown by key also, the result is the same.
Request you gurus to help in this.

Hi Feroz,
Selecting a value in the dropdown would lead to a server round trip if the corresponding event
property is bound to an action irrespective of the kind of dropdown whether DropDownByKey/DropDownByIndex. So there's not anything that you are doing wrong in here. But you should actually go for a dropdown only when the number of values to be displayed are low like less than 30. Even the SAP documentation says like, "Typical UI elements to implement value selectors are dropdown boxes, radio button groups, and item list boxes. Value selectors should only be used if the number of values to be
displayed is low (typically less than 30)."
Regards,
Uday

Importing an Avid 6 edited film in .MOV into Adobe Premier CS6 for re-editing but codec issues!

Hello,
My first time using Adobe Premier CS6.
I have edited a film on Avid 6 but it's far too big.
I want to import this film into Adobe Premier CS6 for re editing so I can export it as a H.264 and make it small enough to post online (currently it's 9gb)
I have tried importing it but I'm running into CODEC issues eeven though it's a .mov. What can I do?
Please help, it's all new to me.
Cheers,
S

More information needed for someone to help... please click below and provide the requested information
-PPro Information FAQ http://forums.adobe.com/message/4200840
What version of quicktime do you have installed?
Exactly what is inside that MOV wrapper?
Codec & Format information, read both links in reply #1 http://forums.adobe.com/thread/1270588
Report back with the codec details of your file, use the programs below... A screen shot works well to SHOW people what you are doing
http://forums.adobe.com/thread/592070?tstart=30 for screen shot instructions
For PC http://mediainfo.sourceforge.net/en or http://www.headbands.com/gspot/
For Mac http://mediainspector.massanti.com/

Nokia N80 Internet Edition Software Update Issue

Hi,
I would like to express my disappointment for the poor service that Nokia has given me. I purchased a Nokia cellphone because I believed it was a reliable company. Nokia is operating in a global world, promoting online upgrades internationally. This does not rely on borders, and yet, on the ground Nokia is inflexible and has not responded to the mobile global population. Despite being within the warranty period, I have to pay a considerable sum of money to fix a problem caused by the online upgrades that Nokia promote.
I used the New Zealand Nokia website to update my Nokia N80i software, and the message on my PC said that the update was completed successfully. When I tried to use the phone there was a message on the screen telling me to contact my retailer. From then on my problems started.
I called the New Zealand Nokia call centre (where I live) and I explained the problem and they advised me to go to the nearest care center, and I did that. As this unit was purchased from abroad (Singapore), I was advised that as the New Zealand care centre is unable to service my Nokia N80i.
I was told to send the phone to a Nokia Care Centre in Singapore because they would have the current issue on hand. Even though the fault was caused by the computer updates, I was informed that the issue would need to meet Nokia's warranty guidelines and be within its warranty period (my phone was under the warranty period at the time) for the repair to be covered under warranty. In any case, I had to cover all handling charges such as courier charges. Having received this advice I paid for the phone (with warranty card) to be couriered to Singapore.
Nokia NZ told me if the phone has been posted to the care centre in Singapore, I should tell them IMEI Number, Date of Purchase, Airway Bill / Consignment Number - which I did.
I then went through a very painful process of dealing with Customs Singapore regarding GST charges. Before it left customs (as I didn't want to pay GST on an item I wasn't importing into Singapoer), I received a call from the Singapore care center advising me that they cannot fix my phone as it is from the Hong Kong market (even though it was purchased in Singapore!!!!) I'm not sure how they could tell me this now (when they hadn't received the phone in Singapore) as they couldn't tell me this when the phone was in New Zealand.
They now said I needed to send it to Hong Kong instead. I told them I could not afford to pay anymore money as I already spent lots to send the phone to them, only to have it return to New Zealand at my cost (which happened when I didn't pay the excessive GST charges).
Nokia then told me to throw my phone in the rubbish and forget about it because they are not responsible for it.
This whole process was ludicrous. The phone was working fine before I tried to use the online update feature, and yet, Nokia refuse to take responsibility for the faults caused by their updates.
Right now I am left with a dead phone. Can anybody help me to fix it?

I am very sorry to hear about your predicament. I always keep my fingers and toes crossed when I update firmware as it can be a risky exercise.
Nokia warranties are usually only valid in the country the phone is meant for, except for European phones where the warranty is valid all over Europe.
I read another thread where someone else got their phone to work following a similar problem to your. Have a look at the thread below.
/discussions/board/message?board.id=hardware&thread.id=7082
Hope this works for you.
Message Edited by cjlim on 04-Feb-2008 09:17 AM

Express edition 11g datafiles Issue

Hi All,
After installing the Oracle database express edition 11g on the 32 bit windows there are some issues with the datafile naming convention.
The datafile undotbs01.dbf belongs to the SYSAUX tablepsace & sysaux01.dbf belongs to the UNDO tablespace.
I don't knw the recurperssion of the same OR whether it is Bug ???
Please help.

And the fix is easy, as long as you don't mind shutting down the database and a startup mount;
And don't move sysaux.dbf onto the existing undotbs1.dbf, using a slightly different name would be a Very Good Idea ...
$ sqlplus /nolog
shutdown immediate;
... database closed ...
exit;
cd <.dbf files directory>
mv sysaux.dbf undotbs01.dbf
mv undotbs1.dbf sysaux.dbf
$ sqlplus /nolog
startup mount
... mounted ...
alter database rename file '<dir>/sysaux.dbf' to '<dir>/undotbs01.dbf';
alter database rename file '<dir>/undotbs1.dbf' to '<dir>/sysaux.dbf';
alter database open;Of course, for those of you on Windows, it's going to cost four extra keystrokes ... mv ... move ;)

Edit Analytics Properity Issue

Similar Messages

Maybe you are looking for