EEM Event Track Question
Hi Experts,
I have the below EEM configured.
No. Class Type Event Type Trap Time Registered Name
1 applet user track Off Mon Sep 8 20:33:19 2014 test
track 1 state down
maxrun 10.000
action 1.0 snmp-trap strdata "TRACK 1 DoWN DETECTED"
My question is:
- Do I need to set the applet to: event manager applet test trap? Do I need this so the trap action would work?
- When the tracked object goes down, will the EEM app continue to generate traps during certain intervals until the tracked object is down? Or will it generate only one trap on the first occurrence the object goes down?
Thanks in advance.
1. No. Just make sure "snmp-server enable traps event-manager" is configured.
2. It will only generate the trap when the object first goes down. It will not generate the trap again until the object comes back up and goes down again.
Similar Messages
-
EEM event track is not supported (version 3.2)
Hello,
I'm replacing a router 2911 by IE3010 (with IP service) and trying to transfer configurations across. I have noticed that on the IE3010 EEM , I can't trigger an event based on Object Tracking.
IE3010(config-applet)#event ?
application Application specific event
cli CLI event
config Configuration policy event
counter Counter event
env Environmental event
gold GOLD event
identity Identity event
interface Interface event
ioswdsysmon IOS WDSysMon event
ipsla IPSLA Event
mat MAC address table event
neighbor-discovery Neighbor Discovery event
nf NF Event
none Manually run policy event
oir OIR event
routing Routing event
rpc Remote Procedure Call event
snmp SNMP event
snmp-notification SNMP Notification Event
snmp-object SNMP object event
syslog Syslog event
tag event tag identifier
timer Timer event
I do have a track that monitors (ICMP-echo) of two IP addresses and I want to do some action when the track is down and this has been working quite well on the 2911. I have found in the IE3010 event detector that tracking event is not available while the same is available in the 2911
Any advise how can I solve this problem and how can I do action based on the status of the tracked object in the IE3010 ?
The software version of the IE3010 is as follows
IE3010 Software (IE3010-IPSERVICESK9-M), Version 15.0(2)SE6, RELEASE SOFTWARE (fc2).
Embedded Event Manager Version 3.20
Component Versions:
eem: (320_rel3)1.0.0
eem-gold: (v320_rel1)1.0.0
eem-call-home: (v320_rel1)1.0.2
Event Detectors:
Name Version Node Type
application 01.00 node0/0 RP
identity 01.00 node0/0 RP
neighbor-discovery 01.00 node0/0 RP
mat 01.00 node0/0 RP
syslog 01.00 node0/0 RP
routing 03.00 node0/0 RP
cli 01.00 node0/0 RP
counter 01.00 node0/0 RP
interface 01.00 node0/0 RP
ioswdsysmon 01.00 node0/0 RP
none 01.00 node0/0 RP
oir 01.00 node0/0 RP
snmp 01.00 node0/0 RP
timer 01.00 node0/0 RP
snmp-object 01.00 node0/0 RP
snmp-notification 01.00 node0/0 RP
ipsla 01.00 node0/0 RP
nf 01.00 node0/0 RP
test 01.00 node0/0 RP
config 01.00 node0/0 RP
env 01.00 node0/0 RP
gold 01.00 node0/0 RP
rpc 01.00 node0/0 RPI need to track if an IP is up with ICMP, Source IP: 192.168.249.1 Dest IP: 192.168.249.2 on port FastEthernet fa0/19
I do not understand how the weights work here with the UP or Down Status can you please explain. I modified your commands a bit and this is what I got, can you let me know if I am on the right path:
track 10 ip sla 10
delay down 10
track 19 list threshold weight
object 10 weight 70
threshold weight down 30 up 70
authentication mac-move permit
ip sla 10
icmp-echo 10.13.249.2 source-ip 10.13.249.1
timeout 300
frequency 5
ip sla schedule 10 life forever start-time now
ip sla enable reaction-alerts
event manager applet Remote_Site_Up
event syslog pattern "TRACKING-5-STATE: 19 list threshold weight Down->Up"
action 1.0 cli command "enable"
action 2.0 cli command "config t"
action 3.0 cli command "interface FastEthernet0/19"
action 4.0 cli command "no shut"
action 5.0 cli command "end"
event manager applet Remote_Site_Down
event syslog pattern "TRACKING-5-STATE: 19 list threshold weight Up->Down"
action 1.0 cli command "enable"
action 2.0 cli command "config t"
action 3.0 cli command "interface FastEthernet0/19"
action 4.0 cli command "shut"
action 5.0 cli command "end"
This is the status with the show track command:
Track 10
IP SLA 10 state
State is Up
1 change, last change 00:29:35
Delay down 10 secs
Latest operation return code: OK
Latest RTT (millisecs) 1
Track 19
List threshold weight
Threshold Weight is Up (70/70)
2 changes, last change 00:29:34
object 10 weight 70 Up (70/70)
Threshold weight down 30 up 70 -
How to use Event Tracking Code for Google Analytics in Dreamweaver CS5
I need to track clicks on links that go to an outside website. I've read about "event tracking code". I'm not sure if it's the right tool to use. And if it is, I've spent several hours reading about it and I can't figure out how to use it. It looks like you need to be an expert developer to be able to make sense of all this. I've always been helped when I ask a question here, I'm hoping that someone can help me.
What my client needs is to know what links are being clicked, and how often. Here's the page where I want to do this: Available Homes - Arizona Vacation Home Rentals
I added a code that I created using the tool I found here: General Event Tracking Code for Google Analytics but can't see to be able to make this work. I added this code to the first link called "View it Here" for the top, left house. Here's the code: <a href="http://www.homeaway.com/vacation-rental/p3495538" onClick="ga('send', 'event', { eventCategory: 'clicks', eventAction: 'clicks on homes', eventLabel: 'Clicked'});" target="_blank">View it HERE!</a>
Then I set a Goal in Google Analytics like it said in the instructions but it doesn't seem to work... I would APPRECIATE ANY HELP!
Thanks,
BrigitteI think you misunderstood what Event Tracking is designed for. This is from Google Help
Tracking Code: Event Tracking - Google Analytics — Google Developers
"Use this to track visitor behavior on your website that is NOT related to a web page visit, such as interaction with a Flash video movie control or any user event that does not trigger a page request."
Clicks on links are page requests. I think for your purposes, you may want the Cross Domain Link Tracking plugin.
Cross Domain Tracking - Web Tracking (analytics.js) - Google Analytics — Google Developers
Nancy O. -
How to invoke the shutdown event tracker when running restart-computer
In Windows command shell, it is possible to run shutdown /d to specify a reason code and /c to enter a comment into the shutdown event tracker to log why a shutdown was being performed.
I'm not seeing an equivalent parameter for the restart-computer cmdlet in PowerShell. Is it possible to invoke the shutdown event tracker when running restart-computer?help restart-computer
says no. There's nothing wrong with using native commands, in a number of cases they are better than what PS provides.
I hope this post has helped! -
Event tracking of Google analatic is not working in Firefox 37
Hi
I am working on event tracking with Google analatics of a site. I can able to track the event in IE and Chrome. But its not working in Firefox 37.
I have tried in safe mode. But problem still existing. Please help me* "Clear the Cache": Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
* "Remove the Cookies" from sites that cause problems: Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]] -
Event Manager question. Monitoring DNS entry.
Hello everybody,
I want to use Cisco Embedded Event Manager in a router for monitoring a DNS entry that normally resolves 1.1.1.1 but if it changes to 2.2.2.2 the router has to change some access list automatically in order to permit different routes.
I know how to configure de "action" sentences for change the ACLs but I dont know how to configure a track or a SLA in order to check the DNS entry and react if it changes.
Someone knows how to do that?
event manager applet ChangeRoutesWhenDNSEntryChanges
event track 21 state ??????????????????????????????????????????????????<----------
action 1.0 cli command "enable"
action 2.0 cli command "configure terminal"
action 3.0 cli command "ip access...
Thank you in advance!!
Marcos.Indeed, I just provided the above example to demonstrate how we can force a DNS lookup and parse the IP address...
I was actually thinking about using the IP SLA DNS probe, but I could not find a way to get the IP address from the results... It just shows the response time.
In order to make the script work, we would most likely need to use some timer to trigger it periodically.
This is an adaptation of my previous example to actually accomplish a periodic check:
event manager applet CHECK-DNS
event timer watchdog time 60
action 1.0 cli command "ena"
action 1.1 cli command "ping host1 repeat 1 timeout 0"
action 2.0 regexp "ICMP Echos to (.*), timeout is 0 seconds:" "$_cli_result" _match _ip
action 3.0 if $_ip ne 1.1.1.1
action 4.0 syslog msg "host1 is now $_ip"
action 5.0 end
If you want to do something as a reaction to detecting the change, that would have to go into the "4.0" block (you can use 4.1, 4.2 etc)
Another thing to consider is that this script would run every minute, so as long as the DNS query resolves to anything but 1.1.1.1 we would re-apply the config changes, which is not that good...
A way to solve this can be seen in the next example:
event manager applet HOST1-NOT-1.1.1.1
event timer watchdog time 60
action 1.0 cli command "ena"
action 1.1 cli command "ping host1 repeat 1 timeout 0"
action 2.0 regexp "ICMP Echos to (.*), timeout is 0 seconds:" "$_cli_result" _match _ip
action 2.1 track read 100
action 3.0 if $_ip eq 1.1.1.1
action 4.0 if $_track_state eq down
action 4.1 track set 100 state up
action 4.2 syslog msg "host1 is now 1.1.1.1 again"
action 4.9 end
action 5.0 else
action 6.1 if $_track_state eq up
action 6.2 track set 100 state down
action 6.3 syslog msg "host1 is not 1.1.1.1, new ip is $_ip"
action 6.9 end
action 7.0 end
Basically we are using a stub tracking object to maintain state. Track object 100 would be up if we know host1=1.1.1.1, but if we detect it is something else we change it to down. Only after we detect that host1=1.1.1.1 again we change the track object back to up, which would enabled detecting another change...
Any actions you want to take should go into section "6" and any clean up (when host1=1.1.1.1 again) has to go into section "4".
It is possible to make this detect any change and not just have a static 1.1.1.1 value by assigning the newly detected value to a variable and basically look for a change... Not sure what is your requirement.
The output below shows how this works...
Router#show run | inc ip host
ip host host1 1.1.1.1
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip hos
Router(config)#ip host host1 2.2.2.2
Router(config)#^Z
Router#
*Nov 9 18:23:18.009: %TRACKING-5-STATE: 100 stub Up->Down
*Nov 9 18:23:18.021: %HA_EM-6-LOG: HOST1-NOT-1.1.1.1: host1 is not 1.1.1.1, new ip is 2.2.2.2
Router#
*Nov 9 18:23:18.065: %SYS-5-CONFIG_I: Configured from console by console
Router#
Router#
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip host host1 1.1.1.1
Router(config)#^Z
Router#
*Nov 9 18:23:42.805: %SYS-5-CONFIG_I: Configured from console by console
Router#
*Nov 9 18:24:18.025: %TRACKING-5-STATE: 100 stub Down->Up
Router#
*Nov 9 18:24:18.033: %HA_EM-6-LOG: HOST1-NOT-1.1.1.1: host1 is now 1.1.1.1 again -
GRC Form Rules Event Tracker Not Capturing Button
Hello,
I have a form rule for the Projects form (PAXPREPR) that I need to fire when a button is pressed. I have set the event tracker, navigating to the form and pressed the button. I then modified a field and saved the record. When I go back to finish creating the rule, When Button Pressed is not an option and the button is not available inthe field name. I entered the button name and it did not give an error, but the rule did not fire when I press the button. Is there another way to trigger a rule on a button?
Thank you,
JoJo,
Are you trying to run a rule when saving? If so you want to use the action: When Validate Record
Have a look at the PCG user guide on page 2-5 for events that you can typically use. Also going forward you should use the following forum for GRC products: Governance, Risk and Compliance (GRC) (MOSC)
This forum is no longer used. I hope that helps!
Regards,
Yasir -
Using Auto Event Tracking to hear Edge clicks
As a designer I have limited experience with GA, but I have extensively utilized onclick attached to HREFs onclick=”javascript:pageTracker._trackPageview(‘/ads/FF1′);”” and seeing outbound clicks on pages reported as whatever i chose to name them. I even used this technique to have rollovers in Flash actionscript report to Google Analytics.
Ran across this blog post and wondering if anyone has tried this for hearing clicks and other events in Edge
Auto event tracking with Google Tag Manager
I have had zero luck with the Adobe Edge Tutorial from 2012 tracking window open on clicks from Edge
June « 2012 « Adobe Edge Animate Team BlogI think you misunderstood what Event Tracking is designed for. This is from Google Help
Tracking Code: Event Tracking - Google Analytics — Google Developers
"Use this to track visitor behavior on your website that is NOT related to a web page visit, such as interaction with a Flash video movie control or any user event that does not trigger a page request."
Clicks on links are page requests. I think for your purposes, you may want the Cross Domain Link Tracking plugin.
Cross Domain Tracking - Web Tracking (analytics.js) - Google Analytics — Google Developers
Nancy O. -
Acrobat 9 PRO - Forms Tracker Question
1. When distributing a form via acrobat.com to multiple targets, can I keep email addresses confidential from individual members on the distribution list?
2. When distributing a form to multiple email addresses simultaneously, is it possible to create a distribution file for each email address on distribution (vs. just 1 file)?
3. Is there a way to create a more meaningful distribution file name than simply file + "0001"? For example, can I use information about the distribution targets (e.g. email address) to name the file?
4. Is there any tickler functionality (e.g. If I haven't heard from this person in 7 days, remind me)?I would also love answers to these questions.
Livecycle and acrobate seem pretty useless whenit comes to tracking and creating unique IDS for form distribution - they expect you to buy Livecycle ES and runa server!
Also there seems to be no documentation about the Javascript(?) that is added when you use the distribution wizard, such as the askuseridentity and askemailclient methods - You would have thought that this would be the basis for at least a tutorial! see below.
form1.ButtonField1::click - (JavaScript, client)
//@@SUBMITURL "mailto:QQQQQ@XXXXXXXXX?subject=Submitting Completed Form&body=Instructions to add this form to a responses file:\n1. Double-click the attachment.\n2. Acrobat will prompt you to select a responses file.&ui=false"
AdobePatentID="B643"
var AdobePatentID = "AdobePatentID=\"B643\"";
// initiate some constants
var METADATA_ANNOT_NAME = "adhocFormState";
var PROP_RESPONDENT_NAME = "respondentName";
var PROP_RESPONDENT_EMAIL = "respondentEmail";
var currentDoc;
if (typeof(xfa) == "object")
currentDoc = event.target;
else
currentDoc = this;
// Only on Viewer/Reader older than 9.0, we'll do the following tasks.
var bAnonymous = false;
var bContinue = true;
if (app.viewerVersion < 9.0) {
// show the email/name dialog if not anonymous
if (!bAnonymous && !currentDoc.dynamicXFAForm) {
var result = currentDoc.askUserIdentity(currentDoc);
if (result == null)
bContinue = false;
else {
var annot = currentDoc.getAnnot(0, METADATA_ANNOT_NAME);
if (annot != null) {
var arrProps = new Array();
arrProps = annot.contents.split(";");
currentDoc.setProperty(arrProps, PROP_RESPONDENT_NAME, result.name);
currentDoc.setProperty(arrProps, PROP_RESPONDENT_EMAIL, result.email);
annot.contents = arrProps.join(";");
// show the select client dialog
if (bContinue) {
var result = currentDoc.askEmailClient(currentDoc);
if (result == null)
bContinue = false;
else if (!result.send) {
app.execMenuItem("SaveAs");
bContinue = false;
// submit the form
if (bContinue) {
var rawURL = "AAAAAA@XXXXXXXXXXXXXXXXXXXsubject=Submitting Completed Form&body=Instructions to add this form to a responses file:\n1. Double-click the attachment.\n2. Acrobat will prompt you to select a responses file.&ui=false";
var submitURL;
if (app.viewerVersion < 9.0)
submitURL = "mailto:" + rawURL;
else
submitURL = "mailto:" + escape(rawURL);
currentDoc.submitForm({
cURL: submitURL,
cSubmitAs: "PDF" -
EEM event manager applet problem
I'm trying to create an EEM applet to log the output of a command to file every 5 minutes. The idea is to get a traffic baseline for implementing control plane policing but I want statistics from at least a whole week (not just while I'm at work). I have a 6506-E running 12.2(18)SXF17a for WLSM (WS-SVC-WLAN-1-K9) support. Initially I was trying to save the file to tftp but it turns out one cannot "| append" to a file on a tftp server. I thought about trying to increment the file name with a counter but instead I opted for this:
event manager applet controlplanelog
event timer cron name controlplanelog cron-entry "0/5 * * * *"
action 1.0 cli command "enable"
action 1.1 cli command "show policy-map control-plane | append disk1:log.txt"
This didn't seem to work because the contents of the file "disk1:log.txt" didn't change over the course of my lunch time. I thought I had the timer messed up so I changed the entry "0/5 * * * *" to "0,5,10,15,20,25,30,35,40,45,50,55 * * * *". That didn't work either so I changed the event to none and ran it manually using "event manager run" and still, the file "disk1:log.txt" contents did not change.
Am I trying to execute an unsupported command or is this an error or am I just doing it wrong? Any help would be appreciated.That is wierd. I must have typed it in wrong somewhere....
I had already removed all eem commands since I used the numbers from the other 6500 log file. When I added them back in with the command changed to "show version" the text file was modified as expected. Even before checking the file, I noticed a difference because I had debugging on per your previous suggestion and these lines showed up in addition to the lines which previously showed up.
545685: Sep 10 15:41:24.674 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT :
545686: Sep 10 15:41:24.674 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT : 6506#
545687: Sep 10 15:41:24.674 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : IN : 6506#exit
545688: Sep 10 15:41:24.674 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : CTL : cli_close called.
At this point I reverted to the original command and it now works as expected.
For the sake of progeny, here is the debugging when not appending to a file.
545990: Sep 10 15:50:27.016 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : CTL : cli_open called.
545991: Sep 10 15:50:27.120 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT :
545992: Sep 10 15:50:27.120 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT : 6506>
545993: Sep 10 15:50:27.120 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : IN : 6506>enable
545994: Sep 10 15:50:27.132 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT :
545995: Sep 10 15:50:27.132 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT : 6506#
545996: Sep 10 15:50:27.132 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : IN : 6506#show policy-map control-plane
545997: Sep 10 15:50:27.144 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT :
545998: Sep 10 15:50:27.144 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT : Control Plane Interface
545999: Sep 10 15:50:27.144 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT :
546000: Sep 10 15:50:27.144 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT : Service-policy input: copp-policy
546001: Sep 10 15:50:27.144 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT :
546002: Sep 10 15:50:27.144 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : OUT : Hardware Counters:(ouput omitted)546017: Sep 10 15:50:27.148 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : CTL : 20+ lines read from cli, debug output truncated
546018: Sep 10 15:50:27.148 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : IN : 6506#exit
546019: Sep 10 15:50:27.148 KST: %HA_EM-6-LOG: controlplanelog : DEBUG(cli_lib) : : CTL : cli_close called.
On a side note I have been pondering something unrelated to my original question but maybe you know the answer to that too. If I have NTP restricted by an access list using the "ntp access-group peer" and "ntp access-group serve" commands as well as through control plane policing, which list is processed first: Do the "ntp access-group" commands keep packets from entering the control plane that don't match the list or do they hit the control plane before being dropped by the access-list? -
We have two iBGP peers with their own separate eBGP (Internet) peers.
We use them as an HSRP pair (over an L2 trunk) for our redundant Internet.
I've created an EEM script that will have the "secondary" router track the "primary" router's HSRP interface to ensure it's still up.
If the link goes down, the router immediately removes all of its iBGP static routes to avoid a routing black hole.
When the link comes back up, the secondary router re-adds the iBGP static routes.
The script works fine, but the maximum delay on the ip sla track command has a maximum of 180 seconds.
Since we're talking BGP, this short delay could wreak havoc if an Internet link is flapping or something.
Here's the track command:
track 1 ip sla 1 reachability
default-state up
delay down 30 up 180
I'm trying to think of a way to make it wait longer than 180 seconds. (900 seconds would be ideal to ensure the issue has been resolved before re-establishing the static routes.
Can anyone think of a way to increase the delay using the EEM commands? The track command is too limited here.
Thanks!
VenLooks like it's calling the add-ibgp, but it stops after the config t.
scp1001-a5t-3#
*Sep 25 15:26:23.680: %TRACKING-5-STATE: 1 ip sla 1 reachability Up->Down
*Sep 25 15:26:23.680: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : CTL : cli_open called.
*Sep 25 15:26:23.681: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : OUT : scp1001-a5t-3>
*Sep 25 15:26:23.681: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : IN : scp1001-a5t-3>enable
*Sep 25 15:26:23.691: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : OUT : scp1001-a5t-3#
*Sep 25 15:26:23.691: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : IN : scp1001-a5t-3#conf t
*Sep 25 15:26:23.801: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : OUT : Enter configuration commands, one per line. End with CNTL/Z.
*Sep 25 15:26:23.801: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config)#
*Sep 25 15:26:23.801: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config)#router bgp 27336
*Sep 25 15:26:23.911: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config-router)#
*Sep 25 15:26:23.911: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config-router)#neighbor 152.179.202.81 shutdown
*Sep 25 15:26:24.021: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config-router)#
*Sep 25 15:26:24.021: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config-router)#no event manager applet add-ibgp
*Sep 25 15:26:24.131: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config)#
*Sep 25 15:26:24.131: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config)#end
*Sep 25 15:26:24.138: %SYS-5-CONFIG_I: Configured from console by EEM on vty0 (EEM:track-bgp-down)
*Sep 25 15:26:24.141: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : OUT : scp1001-a5t-3#
*Sep 25 15:26:24.141: %HA_EM-5-LOG: track-bgp-down: SCP iBGP static routes deleted due to vlan200 failure
*Sep 25 15:26:24.141: %HA_EM-6-LOG: track-bgp-down : DEBUG(cli_lib) : : CTL : cli_close called.
*Sep 25 15:26:24.141: tty is now going through its death sequence
*Sep 25 15:26:31.530: %BGP-5-ADJCHANGE: neighbor 163.230.254.66 Down BGP Notification sent
*Sep 25 15:26:31.530: %BGP-3-NOTIFICATION: sent to neighbor 163.230.254.66 4/0 (hold time expired) 0 bytes
*Sep 25 15:26:31.530: %BGP_SESSION-5-ADJCHANGE: neighbor 163.230.254.66 IPv4 Unicast topology base removed from session BGP Notification sent
*Sep 25 15:26:47.964: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/1, changed state to up
*Sep 25 15:26:48.964: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0/1, changed state to up
*Sep 25 15:26:47.964: %LINK-3-UPDOWN: SIP0/0: Interface GigabitEthernet0/0/1, changed state to up
*Sep 25 15:26:49.909: %BGP-5-ADJCHANGE: neighbor 163.230.254.66 Up
*Sep 25 15:27:23.680: %TRACKING-5-STATE: 1 ip sla 1 reachability Down->Up
*Sep 25 15:27:23.680: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : CTL : cli_open called.
*Sep 25 15:27:23.681: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3>
*Sep 25 15:27:23.681: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3>enable
*Sep 25 15:27:23.691: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3#
*Sep 25 15:27:23.691: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3#conf t
*Sep 25 15:27:23.701: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : Enter configuration commands, one per line. End with CNTL/Z.
*Sep 25 15:27:23.701: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config)#
*Sep 25 15:27:23.701: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config)#event manager applet add-ibgp
*Sep 25 15:27:23.811: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config-applet)#
*Sep 25 15:27:23.811: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config-applet)#event timer countdown time 300
*Sep 25 15:27:23.921: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config-applet)#
*Sep 25 15:27:23.921: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config-applet)#action 1.0 cli command enable
*Sep 25 15:27:24.031: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config-applet)#
*Sep 25 15:27:24.031: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config-applet)#action 2.0 cli command " config t"
*Sep 25 15:27:24.141: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config-applet)#
*Sep 25 15:27:24.141: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config-applet)#action 3.0 cli command " router bgp 27336"
*Sep 25 15:27:24.251: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config-applet)#
*Sep 25 15:27:24.251: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config-applet)#action 4.0 cli command " no neighbor 152.179.202.81 shutdown"
*Sep 25 15:27:24.361: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config-applet)#
*Sep 25 15:27:24.361: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config-applet)#action 8.0 cli command end
*Sep 25 15:27:24.471: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3(config-applet)#
*Sep 25 15:27:24.471: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : IN : scp1001-a5t-3(config-applet)#end
*Sep 25 15:27:24.474: %SYS-5-CONFIG_I: Configured from console by EEM on vty0 (EEM:track-bgp-up)
*Sep 25 15:27:24.481: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : OUT : scp1001-a5t-3#
*Sep 25 15:27:24.481: %HA_EM-5-LOG: track-bgp-up: SCP iBGP static routes re-added - vlan200 UP
*Sep 25 15:27:24.481: %HA_EM-6-LOG: track-bgp-up : DEBUG(cli_lib) : : CTL : cli_close called.
*Sep 25 15:27:24.481: tty is now going through its death sequence
*Sep 25 15:27:42.058: %HSRP-5-STATECHANGE: GigabitEthernet0/0/1 Grp 1 state Speak -> Standby
*Sep 25 15:32:24.474: %HA_EM-6-LOG: add-ibgp : DEBUG(cli_lib) : : CTL : cli_open called.
*Sep 25 15:32:24.475: %HA_EM-6-LOG: add-ibgp : DEBUG(cli_lib) : : OUT : scp1001-a5t-3>
*Sep 25 15:32:24.475: %HA_EM-6-LOG: add-ibgp : DEBUG(cli_lib) : : IN : scp1001-a5t-3>enable
*Sep 25 15:32:24.485: %HA_EM-6-LOG: add-ibgp : DEBUG(cli_lib) : : OUT : scp1001-a5t-3#
*Sep 25 15:32:24.485: %HA_EM-6-LOG: add-ibgp : DEBUG(cli_lib) : : IN : scp1001-a5t-3# config t
*Sep 25 15:32:44.500: %HA_EM-6-LOG: add-ibgp : DEBUG(cli_lib) : : CTL : cli_close called.
*Sep 25 15:32:46.496: tty is now going through its death sequence -
Training and Event module questions.
Hi .
I have some questions regarding Training and Event Management module.
1. IS there a way to configure a custom attendee type for this module ?
2. If no is there a way to rename a existing attendee type. I have a requirement to create a group of attendees type of External Person. I know i can use Company attendee type for grouping external person. But i need to change this Company to Group for displaying purposes. I know i can change the Company via T7778O table but won't it lead to bad consequences ?
3. Is there a way to hide tabstrips on PVOO screen ? i have a requirement to keep only Company tabstrip others are not relevant for my scenario.
That's all for now.
Thanks in advance.
Edited by: kernel.panic on Dec 22, 2010 8:47 AMHi,
thanks this one is ok, the one which I can not find is the info message for when the maximum capacity of the attendee list is reached:
'Optimum capacity reached, only essential or wait list bookings possible' This one I want to change into a warning message.
br,
Ovidiu
And I have a new question as well
In the Attendee List layout is it possible to add columns which are not in the column set from customizing e.g. Personnel subarea,
Employee subgroup, Employee group etc?
Thanks
br,
Ovidiu
Edited by: Ovidiu Moldovan on Apr 20, 2010 3:51 PM -
We installed a C150 in our office and we enabled Message tracking on the day we installed the device. However when we try to find messages all the way back to October (the 13th, the day we installed it) there were no results found. At the top of the message tracking page we have this:
Available Time Range: 13 Oct 2008 15:04 to 23 Dec 2008 12:50 (GMT -0500)
Data in time range: 99.98% complete
Is there any way we can track messages back that far?
I do have a support case open, but I wanted to see if anyone else has that issue.The following article is in the knowledge base:
Earliest 15% of Tracking Data Is Not Currently Available for Querying
Question
Why does the "Available Time Range" appear to be missing the oldest data?
Answer
This is a known centralized message tracking issue in which the earliest 15% of tracking data is not currently available for querying. However, the appliance retains the data, and the data will be available for querying after this issue has been resolved.
A future release will provide access to 100% of the time range in the tracker database.
This is Defect ID 39471.
Hope this will explain your problems (the only way to find the missing part is via the CLI-find/grep command).
Peter -
I have a question about iPhoto 11 events. My camera was set to the wrong date for part of an event. I went in and did a batch change of the time and date of the affected photos. However, the date range beneath the title of the event still has the old erroneous date, and the event gets sorted by this date range. Is there a way to go in and change that date range under the title of the event? I go to the event and click on info, and the event shows the correct date range for the pics, but it is not changing the date range under the title. Thanks for any help in advance.
Thank you - I had the same problem and found your helpful answer. However, this is actually a work around to a bug in iPhoto - it's not how the Apple Support pages say it works and common sense says that if you change all the dates in an event it should sort to the right place without being re-created. Can you help me with one more thing - how do I bring this to Apple's attention so that they fix it in a future release?
Thanks again for the help. -
I have a shot that is panning and asit pans a television will come onto the screen. My plan is to corner pin an image on to the TV. The problem is there is nothing to pin the image to until my trackers on the TV enter the screen. I just did a quick test and tried keyframing until I get all 4 trackers on but It's not as smooth as I would like it to be.
I read a post here about using the offset track but I didn't really understand what the poster was saying. Could anyone give me any quick "Motion Tracking for dummies" explanation of what I need to be doing? Also- we haven't shot the shot yet so is there a better way to do this setting up four trackers- one on each corner of the TV?Yeah- I studied up on that. I've actually talked the DP into changing his shots around so the TV is always on screen. I figured I would leave the question opened for future use. Thanks
Maybe you are looking for
-
Using once created prepared statement with different connections in Oracle
Can I use same statement cash using different connections in Oracle For example I have a prepared statement p1. After its using i close connection (return it to the pool) Next time I want use p1 statement using another connection. Question : When I c
-
How do I close out the picture folder after I've tagged my pic's and clear my workspace? I used to be able to click on "file" and "close".
-
Converting Crystal Date Group to SQL Command
When selecting the option to group on the server, I found that there are requirements in addition to selecting the option. I have a date grouping in Crystal like the following: dateadd("d", - weekday({table.date}, crMonday)+1,{table.date}) Can this b
-
ITunes 8.2.1.6 install problems
Downloaded the new iTunes 8.2.1.6 file fine, but when installer ran kept getting an error saying "Invalid drive F:". Changed my secondary hard drive, where my music is stored and I wanted to install iTunes, to F. Installation went through just fine.
-
I have installed WebAS 6.40 and started the J2EE engine successfully. Up to now I could not find the way to configure the right JMS entries (factories, destinations). Can anybody help and describe how I have to configure JMS...I am not to able to fin