Equium L40 start problem

Hi
I have to use F1 to start my Equium L40 every time i tun it on. It will then boot up ok but it has forgoten the time and date, once i update the time/date, the computer works perfectly i can access all my email accounts etc without having to re set anything.
The problem started after replacing the battery due to the old one being almost completely dead. I've noticed that the computer will not run on AC alone without the battey fitted but is still charging the battery ok. (so the adapter is ok)
I like the computer and don't really want to buy a new one but it's very frustrating and time consuming when i turn it on.
Maybe there is a back up battery i can change to repair the fault?
Any help would be appreciated?

Thanks for the advice i must admit i havn't had the unit on charge for more than about 4 hours so i'll give it a try.
My suspicion is that a circuit has overheated and failed because it's been overloaded trying to charge a worn out battery and is causing the issue of not working on the ac adapter alone.
It's not too much of a stretch of imagination to think that the failed circuit also charges the Bios battery so it may be just flat not faulty! (in which case a long charge may have no effect)
If the long charge fails i may need advice on stripping the computer, recognising the Bios battery so that i can test it.
Has anybody got a repair manual or know where to get one?
I'll let you know what i find
Thanks

Similar Messages

  • Toshiba Equium L40 - Recovery Fail

    Hi,
    My toshiba equium L40 started to become really slow so i decided to start over fresh, so i put in the recovery CD that i got with the laptop and started the recovery, chose the language and the DOS screen pops and starts doing what it does but it then gets stuck at 58% and then eventually cancels.
    whats up with it and how am i going to fix it ?

    It sounds like either your HD or the DVD is having a problem.
    I'm guessing that you have a Toshiba Europe machine?  You might check their forums to see if they have any specific knowledge of the issue.
    http://forums.computers.toshiba-europe.com/forums/index.jspa

  • Equium L40-156 boot up problem

    I have an Equium L40-156. When I press the power button the power light comes on but there appears to be no hard disk activity. If I manually switch it off by pressing the power button for several seconds, leave it for a couple of seconds and press the power button again it starts normally.
    Any ideas please?

    Hi mate,
    Did you recently updated your BIOS, installed some more RAM/another HDD or some software?? Maybe some driver update??
    Since when does the error appear? And do you have still warranty on it?
    So, if yes, then bring your machine to an authorized service partner and let them check your machine. Would be the best...
    Greetings

  • Equium L40 - Windows wont start, message on screen

    Hi
    I have a Toshiba Equium L40 - 17M.
    Recently when updating my virus protection my computer tried to restart but now wont load properly.
    Now everytime i try to switch the computer on, after the initial Toshiba setup screen I am greeted with the following message in the top left corner of the screen.
    A disk read error occured
    Press Ctrl + Alt + Del to restart.
    However, this message just appears again!
    Any suggestions please!?

    It could be a file system corruption problem, in which case you can connect the HDD to another PC and run CHKDSK on the drive.
    If that's no help, then check the HDD for bad sectors using the Advanced Test in Hitachi DFT (Google is your friend)
    Or you can try running Recovery from your Recovery Discs. This will format the HDD, so you will need to backup your data first if its still there (you can use a USB 2.5" HDD Adapter).
    If you really need your data back, there are Data Recovery programs you can download to search the HDD for the lost files.

  • Equium L40-10X - Can't install Windows

    Hi all,
    First actual post but been around on and off for a while. I hope somebody here can help!
    I have a Toshiba Equium L40-10x laptop with a strange problem. It came to me second user with the problem already so I don't know any history other than what I have tried. When you boot the machine it comes up with a TRAP 00000006 exception error and stops. The hard drive has been low level formatted, formatted and partitioned and has nothing on it. The memory has been replaced and confirmed working. When you try and use the recovery cd (F12 on startup) it goes to the select boot option menu, I select CD player and it makes a few noises and then the error appears. I have also tried a WIN XP and WIN Vista CD with the same effect.
    Googling the problem seems to suggest NTLDR problems or memory but drive has nothing on it and memory has been tested and confirmed fine.
    Other possibilities are CD drive or BIOS. Bios version is at 2.10 and I know that BIOS available is 2.30 but unable at the moment to work out a way to upgrade the bios. I do have a USB Floppy drive available.
    So, thats the problem, any thoughts?
    Thanks
    Message was edited by: acprc

    Have you access to the HDD using floppy start disc?
    Connect the HDD to other notebook, create two partitions, copy I368 folder on second partition. With floppy disc try to access this folder and start WXP installation using winnt32.exe.
    Check advanced search option on this forum and you will find many threads with good description how to do this.
    Play a little bit with it. ;)
    Is the optical disc drive working properly?

  • Equium L40-14I does not power up if its cold

    When I push the power button down when the machine is cold, the green power lights come on for about 2 seconds and then go off. If I give the laptop a bit of gentle heat for a about 30 seconds the laptop starts first time and runs perfectly until the machine is turned off. The laptop is Equium L40-14I
    Hope somebody can help with this weird problem.

    Appreciate the reply.
    I did put another tested lead into the laptop and it still does the same thing.
    I bought this as reconditioned a couple of years or so ago for my wife to use and practice on. Its had a couple of problems along the way. I changed the hard drive and the shop that sold it to me got the keyboard working again (well after the 3 months warranty had run out). One day it was working ok the next it developed this weird ritual.
    I am not a technician but I have had this thing to bits and put it back to again with the help of the videos on YouTube, so I will have ago if a possible solution to the fault is found.

  • Equium L40 - internet does not work if I open more than one website

    I have an Equium L40-10X and although the system runs fine, it does not like the internet. If I open more than one website, a little box comes up saying that Internet Explorer has incurred a problem and that it must be restarted. This is becoming excruciatingly annoying if I am in the middle of something important and I lose the website that I was on!
    Especially with me going off to uni soon too! It especially will refuse to work if I need to download something e.g. I recently bought an Apple iPod Nano, and I needed iTunes in order for me to put music on it, but as soon as it starts the download, the "internet has stopped working" box pops up and I have to start everything again, but instead of it working -it simply does not!
    This is becoming an often occurrence, and it makes me incredibly stressed!
    Please help.

    Hi
    Do you always use the up to date windows OS?
    Such errors appear if the registry is dirty and the WinOS was not updated!
    Update the Windows on the Microsoft page to the latest state!!
    Furthermore you should clean the registry using the freeware tool called CCleaner. Its nice!
    So finally one hint;
    You can access the internet not only with Microsoft Internet Explorer but also with another internet browser like for example Firefox.
    I recommend checking such possibility.
    regards

  • Equium L40-17M PSL49E - Wlan stoped working after BIOS update

    Hi all,
    I have problem with my lap-top.
    The laptop is Equium L40-17M, model PSL49E-00C005KS.
    Before couple days i update my BIOS with version P20B200 (bios-20080617131309), and after update, internal wireless stop working.
    Show me device is enable but activity is off, and i can't turn on device.
    First thing what i think is "Windows" and i start recovery disk. But after recovery problem is still exist, wireless do not working.
    Then i put external USB wireless, and try to connect with router.
    Computer recognize USB but he also do not working good, therefore the problem is not in wireless (i am not sure for this), but i think that problem is it because laptop can't recognize correctly USB device.
    I want to flash bios with old BIOS but i don't have it
    I will grateful to someone who have same problem, tell me how i fix it.
    Or send me old bios for my laptop.

    My mistake, I don't explain correctly what I done.
    Yet yesterday I download driver for WLAN from Toshiba site and install it, but is no result, problem still exist. Combination FN+F8 is forbidden (no displaying icon or not working signal lamp) - its all the same laptop don't have WLAN. It is absolutely strange.
    My laptop OS is: Windows Vista premium (32bit), and first I download BIOS for Vista version 2 of course (I am not such stupid to download BIOS, before read notice), after problem I download & BIOS for XP (just for test).
    And result from test is: WLAN yet not working, when I push Fn+F8, icon for WLAN show me that device is turn off and every time is always off. No matter what button I push or what command execute. Install driver for WLAN, but its same result at - not working devices.
    After all this operation I flash BIOS, with version for Vista, recover laptop with recovery disk and install driver for WLAN. No matter, my hard working was unjustifiable, device not recognized & not working.
    May be tomorrow I try to install Linux, just for try-out.

  • Equium L40 - CDDVD doesn't recognise Audio CDs

    Hi,
    I recently bought an Equium L40 and it's fine except that the CDDVD drive doesn't seem to recognise Audio CDs. The drive just whirs and grinds for a few seconds, and then stops. DVDs play correctly. The Audio CDs that I've tried play correctly on other machines. I've tried changing the AutoPlay settings to "Ask me every time" but it doesn't seem to help. Has anyone seen this problem before ?
    Thanks in advance for any help.
    Regards,
    Chris

    Hello Chris
    Have you tested it with different original music CDs (older and newer one)?
    Can you see content of these CDs in Windows Media Player?
    I tried it on my P200 with two original music CDs and there is no chance to start them from Windows Explorer or to see the content there. Start Windows Media player and I hope it will work.
    Please post the result.

  • Equium L40 - Vista refuses to boot after product recovery installation

    Hi,
    I have had to carry out a product recovery uses the supplied restore disk on an Equium L40 (PLS41) laptop. The recovery procedure does its job to the end, reformats and copies all the files then restarts. Now the problem starts....
    The pc gets past the BIOS splash screen then it goes completely black with only a flashing underscore cursor in the top corner of the screen. No HDD activity or CD-rom activity.
    I have done the recovery about ten times now. All with the same result. I have tried the repair procedure using a Vista boot CD and I have also tried it using another disk that came with the computer, Vista anytime upgrade. There are no faults found, it see's the hard drive and shows that the vista files are on it, also sees the winRE partition.
    I have even tired installing fresh from the anytime disk. This also reformats the drive, copies and unpacks all the necessary files, starts to install updates off the disk and then says it needs to reboot. It reboots and goes straight to the black screen with the flashing underscore cursor. This happens whether I press the "hit any key to start from CD-rom" or leave it to boot from the HDD.
    I have been trying to fix this for two days now including endless hours of forum searching, my friend, whom the pc belongs to is getting quite irate as am I. I need help. Does anyone know how to fix it?

    Hi
    According to your message I believe that the HDD is faulty.
    I think there is a faulty master boot record (MBR) on the HDD and therefore the notebook refuses to start.
    One question; did you try to set the BIOS to the default settings? If not try this.
    If it doesnt help and the notebook will still not boot up then you should ask the ASP for the check.
    In my opinion its a HDD issue and possibly the HDD must be replaced!
    Greetings

  • CD/DVD drive open on its own - Equium L40

    Hi,
    I have a Equium L40-10X laptop bought recently from Pc World. It's been working fine until recently my cd/dvd drive popped open on its own. I closed it and then about 10 minutes later it did it again. This happens every so often. After a bit of research I found out it could have been a spyware issue. Scanned, and removed all traces etc. Problem appeared to be gone, but alas, the drive once again popped open.
    Recently the drive is not reading discs as well. It seems to work when it wants for any time between 10 seconds and an hour at a time. The things got a mind of its own....and when it's not working, the button to open the drive doesn??t seem to work. I have to use a paperclip to open the drive.
    Either I have a haunted laptop or there's something wrong.
    Has anyone had any experience of anything like this before or have any advice on what to do?
    Thanks, Jon.

    Hi mate
    I didnt notice something like this before but I presume its a mechanical problem.
    Dont think 3rd party software (program, spyware, virus, etc) could cause this issue.
    Additionally you have said that the drive is not reading discs as well.
    In such case I would recommend contacting the ASP in your country and to ask for the drive check and if necessary for an ODD drive replacement.
    If the warranty is valid the replacement should be done for free.
    Best regards

  • Equium L40 - cannot connect through wifi or the ubs lead plugged in

    Hi
    I have a Equium L40. I cannot connect through wifi or the ubs lead plugged in.
    It comes up " Internet Explorer has stopped working. a problem caused the program to stop working correctly"
    It is saying in am connected to my hub and have a strong signal.
    Can you help
    Thanks
    Steve

    Hello Steve
    Have you tried to use some other browser?
    Do you use Skype or some other messenger? Can any of them connect properly?
    I dont know what the real problem is. Non working Internet explorer or WLAN connection in general?

  • Equium L40-10X PSL41E keeps freezing - Where can I find BIOS?

    Hello,
    I'm new to this forums so please be gentle.
    I have an Equium L40- 10X laptop
    Model number PSL41E-004004AV
    Runs on 32 bit Vista home
    My problem is it keeps freezing gand i can do nothing but re-boot it.
    The computer problem report section is telling me i need to update BIOS.
    I have tried and tried on the Toshiba website to find/install the correct one but to no avail,
    Can any one help me?
    Please

    Hi
    You can find the latest BIOS on the Toshiba European driver page because this is a Toshiba European notebook model.
    Please check this:
    http://eu.computers.toshiba-europe.com/ -> support & download -> Download Drivers
    There you will find the Equium L40 PSL41E
    Greets

  • Question about graphics cards for Equium L40 - 10X

    Hi - new to this but really hacked off so hopefully someone can help me.!
    I bought a Equium L40 - 10X in August and thought it was good for what I wanted, especially after seeking advice and speaking to 'an expert' at my local pcworld.
    However, I think the graphics card is not good enough to support the games I have got - Medal of Honour Warchest, Hitman Triple Pack and Call of Duty 2. They all sem to recommend a nVidia graphics card as a minimum requirement. The card in the laptop is an Intel(R) 945 Express Chipset Family (I think) and the OS is Vista Home Premium.
    Problems I am experiencing include loss of graphics and stuttering during play.
    Can I upgrade to an nVidia graphics card or is the one I have got sufficient but I just need to change some settings?
    Haven't got a clue really, so help would be much appreciated!

    > I bought a Equium L40 - 10X in August and thought it was good for what I wanted, especially after seeking advice and speaking to 'an expert' at my local pcworld.
    Either you was not clear enough or the expert from pcworld have provided the wrong information and wrong advice.
    Fact is that the Intel shared GPU was not really designed to play the newest games.
    The shared graphic card is simply not powerful enough to run such games smoothly!
    > Can I upgrade to an nVidia graphics card or is the one I have got sufficient but I just need to change some settings?
    NO, this is not possible because the notebooks graphic cards are fixed on the board and cannot be removed.

  • Equium L40 10X Blinking green power LED

    Hi Guys,
    I have an old Equium L40 that I haven't used it in a while.
    Now when I plug the power adapter in the power led just blinks green constantly.
    I've checked the blink codes but I can't find one for mine. It simply turns green for a second and then off.
    Then green for a second then off and does this constantly.
    I've tried removing the battery for a few minutes and then holding the power button down for a minute, but I just get the same result. The power adapter is a the one that came with the laptop and as far as I can tell works fine.
    Any other ideas would be greatly appreciated!
    Thanks guys!

    Hi
    Power Indikator (DC IN) indicates the power status with the AC adaptor connected.
    The green (not blinking) means power is being supplied and the computer is turned on.
    The power indicator on the front of the computer will glow green when the computer is switched on.
    The blinking amber indicates power is being supplied to the computer while the notebook is in sleep mode.
    Unfortunately, the DC IN green blinking status looks like a hardware problem.
    Probably the power supplied to notebook is abnormal or there are some problems with power supply electronic on the motherboard.
    By the way: please check the RAM modules. Remove one and test the unit using only one module in each slot. Check both modules.
    Some years ago, a friend of mine has had some problems with the notebook. The blinking LED indicated the RAM issue

Maybe you are looking for

  • Plz help in calling of reports from Form in browser

    Hi! I am using 9iAS(1.0.2.2.1) + 8.1.7 database on the same machine with Win NT4.When i invoke report from my system's main form(oracle form6i) using parameter list as Run_Product(reports,'..\iReports\glrxx13.rep',synchronous,RUNTIME,FILESYSTEM,pl_id

  • Question to chart in Xcelsius

    I want to have one chart to show Transport cost and Transport Duration of Cusomer A1 and A2. Does anybody know which chart that I can use to compare two KPI for customer A1 and A2 in Xcelsius? How to use it, give an example dashboard.Thanks for any i

  • Dreamweaver Download sync query

    Hi When I want to pull a site down from the remote server I do the usual click on the arrow down button and then when it says Do you wish to get the entire site? I say yes. This tends to take about half an hour because we have tniyMCE on almost all o

  • Contacts Pictures Randomly Deleted

    I'm using iCloud to sync my contacts. I try to add a picture to a contact in the Contacts app in Mountain Lion and then click "Done." But when I come back to that contact card after clicking on another contact one of two problems happens: 1. The pict

  • About "populating users in oracle Bam administrator"

    in Fusion Middleware Administrator's guilde, 23.3.6, it mentions 2 way of populating user in BAM. But there are some difference.. if use RegisterUsers Utility, the user's groups are also populated in BAM,(can see in Active Studio, change folder permi