Error in Setup Tables for QM Inspection Lots

Hi,
I have an issue when I attempt to fill the setup tables for QM that I receive the following error for the Inspection Lots (QV) only. When I fill the setup tables for Notifications and Inspection Results, then these are OK and use the same standard function module 'qmex_inspection_lot_import_ini'.
"Internal error in program SAPLQMEX, function module / subroutine qmex_inspection_lot_import_ini, code 1".
Has anyone any ideas of the cause or have you experienced this before?
Thanks,
Scott

Hi,
The most likely reason that leads to the above error message in your
system is an inconsistency of the inspection lots.
To get the inconsistent inspection lot,please check your system in the
following way:
- transaction OLIQBW for running Setup table
- switch on debugging mode
- set break point in the function QMEX_INSPECTION_LOT_IMPORT_INI
on the line:
ELSE.
   MESSAGE e011(qmex) WITH sy-repid
                           'qmex_inspection_lot_import_ini'
                           '1'.
> then excecute F8 to go to this break point.
- double klick on ' l_qals-prueflos'
on line 77 in the same function QMEX_INSPECTION_LOT_IMPORT_INI:
READ TABLE qave_tab INTO l_qave
                    WITH KEY prueflos = l_qals-prueflos <      here !
                    BINARY SEARCH.
Please check following note:
305244 Missing operations for the inspection lot
89541 Inspection lot exists w/o status object: EM BS001
536769 Inspection lots without status object
Thanks,
Venkat

Similar Messages

Error while filling setup table for Sales

Dear Team,
We are getting following error while filling setup table for Sales (application component 11) and for Billing (application component 13),
application component 11
Error determining rate: foreign curr. local curr. INR date 08.10.2007 (doc. 673624) (JOB - RMCVNEUA)
Message No M2810
application component 13
Billing document 480050000: error determining stats. currency rate (no updating)
More faulty documents found than the tolerated 0000000000 (JOB - RMCVNEUF)
I have seen lot of threads based on this but all r showing diffrenent currency to INR but for the above mentioned documents currency is in INR only so why it is showing the error I am not able to determine.
If anybody faced this problem kindly reply to this.
Best Regards,
SG

Hi There,
Might be your using a wrong document number.
I mean if your using the 11 you should use only Sales document number and for 13 you should only use billing document number.
If you use vice versa that error will throw.
Regards,
MQ

Error while filling setup tables for 2lis_13_vahdr

Dear friends,
I am getting below Error while filling setup tables for 2lis_13_vahdr.
More faulty documents found than the tolerated 0000000000
Message no. M2222
Can any one guide me how to address this issue.
Thanks and Regards
Nithya

Hello Nithya,
It seems the No of tolerated faulty documents that you have given is 0. So when you initialize try to these.
While executing OLI*BW including a value in the maintain "No. tolerated faulty documents" - 5000 or 10000.
Then execute the program in background.
Once the job is completed check the background job log if any errors.
Thanks
Chandran

Error while filling setup table for 2LIS_03_BF

Hello,
I am getting an error while filling set-up table for 2LIS_03_BF.
Following is the screenshot of the same.
If I check in ST22, I get following,
I could fill the setup table for other datasource 2LIS_03_BX without any problem.
Please suggest.

Hi,
Can you try filling the setup table data for that range in background?
Sometimes because of huge data that you are trying to fill it might through you a dump. So please execute it in background and see if it works?.
But still can't really say what that dump tells from what you attached.
Thanks,
Sathya

Error when running setup table for 2LIS_03_UM

Hi experts,
When running the setup table for 2LIS_03_UM, we got the error message "Plant FP01 does not exist." Any suggestions on how we can fix this?
Thanks,
Donna

check if this plant has been maintained in source system or not. If not, ask the concerned team to maintain it.
Another way may be to allow error records which should ignore errornous records and rest should be filled in setup table.
Regards,
Gaurav

QM error for old inspection lots

Gurus,
We encountered the following error when we are saving old inspection lots with inpection end date
05/15/2006... please advice how to proceed
Error:
The current inspection stage is not available
Message no. QD704
regards,

Hi,
Do we need to change the posting date to match the insp end date to proceed?
please advice,
regards,

UD error for old inspection lots

Gurus,
We encountered the following error when we are saving old inspection lots with inpection end date
05/15/2006... please advice how to proceed
Error:
The current inspection stage is not available
Message no. QD704
regards,

Hi,
You posted the same question under the forum of business process expert! You should check the posting date of old inspection lots before you save them!
Good luck
Z.T

Setup tables for invoices header data (2LIS_13_VDHDR)

Hi experts,
I am using 2LIS_13_VAHDR and 2LIS_13_VAITM to transfer data to SAP BW. Through the t-code SBIW, I I run the job to fill setup tables with invoices data. the job is completed succefully. when I check the extractors in RSA3, the extractor 2LIS_13_VAHDR doesn't bring any data while 2LIS_13_VAITM bring a set of items !!
I m wondering why I dont get invoices header data!
Thank's a lot for your help.
Abdess,

Hi,
Did you delete the old initialization request from BW and also delete old setup table.
Because the issue is strange, If you are able to see entries in item then header should also fetch data.
Repeat the steps again if you have time.
Use T-Code LBWG to delete setup table.
Delete MCXE13 entries in LBWQ.
Use T-Code OLI9BW to fillup setup table for 2lis_13.
Thanks,
Shakthi Raj Natarajan.

Standard Report for all inspection lots

Dear all,
Pls guide me from where I can retrieve the data for result recorded for MIC, inspection lot wise.
Actually currently working for Pharma company where we are using, Inspection Plan (task list type Q), with inspection point 200 u2013 Physical sample. Materials are being managed through Batches, so each inspection lot is having separate batch number.
Now the requirement is to find a STD sap report that can retrieve us the result for a material for all the inspection lots (Batches) it have, in the report type from where I can down load it to word/excel.
In short, the report should contain, Material, results for all MICs under all inspection lots.
I have already tried out;
QGP1 but it shoe the result for only a MIC at a time.
QGA2 but not able to visualize results for all MICs at once.
MCXB but, gives only the quantity of MICs not the results of it.
Regards,
Shyamal Joshi

Hi Craig,
The requriement is to have results for the Inspection lots only, not for the batch values.
The report MCXD is giving the quantitative analysis for the batches, I will be very pleased if you suggest me any report that gives me the results (values entered during result recording) of these MICs, inspection lot wise, just as the MCXD give quantitative.
I think the term BATCH is creating confusion, that is Y u have suggested me CL03N, but as I have mentioned eariler also, currenlt working with Pharma company, where each manufacturing lot is give a batch number, (in sap terminology the Batch management function, MSC1N), that is why i freauently used BATCH. Sorry for that communicational error from my side, and I am very much thank full to you for your each valuable comment, suggestion.
Regards,
Shyamal Joshi

Taking long time filling the setup tables for sales and shipment

Hi ,
I am trying to fill the setup tables for sales and shipment and it is taking lot of time .
It took 16 hours just to bring 6 months of sales history data in the test environment .
Cn anybody help on this issue why it is taking that much of time ...
I am trying to load the sales data from R/3 into APO-BW from 2005 to 2007 .......
It is taking 16 hours to fill the data for only 6 months .

Hi,
1. delete data and refill the setuptables again by spliting to several small pieces.
2. compare the data. wht is the last Document numner in RSA3(Maximum one). Start from Maximum one. may be bit complex approch.
you need to check with PSA and base tables.
keep one thing in your mind you need to check againest MSEG and BSEG only. noy BKPF and MKPF.
correct if i'm wrong.
either refill or create a user exit to avoid duplicae records(you should have very good understanding of data, it will lead to inconsitent data for delta records).
User exit not a good solution. it's one possibility.
****Assign Points If Helpful****
Regards,
Ravikanth

Problem while filling the Setup Table for the DS 2LIS_02_SCL.

Hi All,
When I am trying to fill the Setup table for the DataSource 2LIS_02_SCL and only for one specific Purchase Order, it is showing me a message like
u201CDataSource 2LIS_02_ITM contains data still to be transferredu201D
I have deleted the Setup Table and I want to delete the entries from SM13, but I do not have Authorization.
Also, here I am trying to fill the Setup Table for 2LIS_02_SCL and not for 2LIS_02_ITM, but the message displayed above is showing as 2LIS_02_ITM DataSource. I think the Setup Table will be same for both the DataSources.
Waiting for your valuable inputs.
Thanks in Advance.

Hi,
When you want to fill the setup tables first you need to delete setup tables to avoid the duplicate entires in setup tables ( you can delete the setup tables by using t.code LBWG with application no is 02)
In your case, the data souce is 2LIS_02_SCL for purchasing.
when you want to delete the setup tables by using t.code LBWG with 02 application no it will delete all the purchasing related data from all the data sources like
2LIS_02_SCL
2LIS_02_ITM
Before the deletion of setup tables you need to clear the delta Queues and stop the V3 jobs, which loads the data to Delta Queues (RSA7) and Update tables(LBWQ).
you need to run the V3 jobs manually by using LBWE > Job control > and schedule the jobs until the delta queues will get 0 records. that means no data will be available in RSA7 and LBWQ
go to SM37 to see the jobs LIS-BW-VB_APPLICATION_02,
once the delta queues gets 0 records by running V3 Jobs manullay.
Then remove the released state jobs > remove from schedule means delete the jobs in LBWE > Go to job control > you can delete the released jobs.
Becuase No postings to be done in application tables, while running setuptable filling you should take some down time to fill the setup tables.( OLI*BW) *=Application number.
Once you clear the Queues and delete the v3 jobs, then you need to fill the setup tables after deletion of setup tables.
once you fill the setup tables , by running intialization to BW side the delta Queue is formed for the data source in R3 side
Now the postings can be done in R3 side, so you need schedule back the V3 jobs, which you already delted from LBWE to load the data from application tables to RSA7 or LBWQ.
I hope this may help yoou.
Regards.
Rambabu
Edited by: Rambabu velanati on Jun 9, 2010 4:41 PM
Edited by: Rambabu velanati on Jun 9, 2010 4:52 PM

How partial inspection is done for a inspection lot & vendor payment done based on inspection result

Dear Gurus,
In our business 1000 bag material is received in one material document. So one Inspection lot is created.
Now business take randomly 10 bags from that 1000 bag & inspected. The Bags are inspected on various parameters such as Weight , Fabric , Valve Size , Cross Sec Area, Print Quality , Stitching Thread , etc . The values for all this types of parameters are prepared in an excel sheet in a prescribed format.
The Values for each Quality Parameters are then matched with the desired prescribed average figures.
Based on the Values which deviate from "Average" figures , deductions are computed
Logic is 1% for single defect in a bag for 1 parameter . Likewise if more defects is found then add 1% in multiples
e.g 1% + 5 defects then .05 * basic Raw material cost .
This figure along with proper description is recorded under "Remarks" column of the report format and send to Accounts department for the
deduction process from Vendor
we need to capture the inspection parameters in system as per the above process.
And please tell me how I configure this process in SAP .
Thanks & Regards,
Bubai

Hi Bubai,
you can create a QM Control Key (which is used to QM View of Material Master) which you have to set the indicator Block Invoice. This indicator is blocked invoice with blocking reason I (I = Inspection) if there is still no usage decision for the inspection lot or the inspection lot is reject.
(SPRO -> Quality Management -> QM in Logistics -> QM in Procurement -> Define Control Keys).
Best Regards,
Apostolos

Error when running report: "Error in aggregate table for InfoCube"

Hi Experts
We had a temporary error, which I would like to find the root cause for.
We where running a Workbook which is based on a multiprovider. For a short period of time (around 10 minuts) we got the following error when we executed the workbook based on this multiprovider:
"Error in aggregate table for InfoCube"
There where no loads or aggregates rolling up on the cubes in the multiprovider.
I see no short dumps as well in ST22.
Have anybody seen this error before, and how can I trace how this error occured?
Thanks in advance.
Kind regards,
Torben

Hi Sneha,
I will Suggest u to do some RSRV tests.
Go to transaction RSRV. There you will find test for aggregates. Just Perform them and see whether you get any discrepencies.
Regds,
Shashank
Edited by: Shashank Dighe on Jan 4, 2008 10:51 AM

Error - Invoice is blocked for quality inspection.

While making payment to vendor the error shown - Error - Invoice is blocked for quality inspection.
Can anybody help ?

This is caused by customizing of QM in procurement.
You can only pay if the material is released from quality status.

How to Fill Setup tables for MAP (IS- Retail)

Hello,
I am working on MAP scenario, I found the following data sources as a part of it. Can anybody please tell me how to fill the setup tables for these and what are the base tables for it??
2LIS_40_REVAL
2LIS_40_S202
2LIS_40_S207
2LIS_40_S208
Your reply is highly appreciated.
Regards,
Naresh

Hi Naresh,
We cannot fill setup tables for each data source.
ORISBW -- This is the t-code to fill the setup tables for all the data sources which are related to application component 40.
If you want setup tables names of your data sources please check below.
2LIS_40_REVAL --- MC40RP0REVSETUP.
Comes to your second post.
2LIS_40_S202
2LIS_40_S207
2LIS_40_S208 these are LIS data sources, whic are replaced with LO data sources in SAP BI 7.0
If you are using LO data sources then no need to use LIS data sources.
Regards,
Venkatesh

Error in Setup Tables for QM Inspection Lots

Similar Messages

Maybe you are looking for