Errors in executing VI with a project

Hello,
The Vi file attached is running when it is not included in a project i.e when I run it separately. When I add it to a project on cRIO in FPGA mode it does not run. I get all the possible errors like 'Sub VI is not executable (for all sub VIs)', 'wire type not supported in current target', 'diagram constant: type not supported in current target', etc..
The VI includes running LED. My main motive is to replace the LED with a digital I/O module.
Please help.
Thank You
Attachments:
fc1.vi ‏54 KB

As crossrulz mentioned this VI will not work at all in the FPGA world. Follow his advice.
If this is your first FPGA project; as a caution do not use to many front panel elements, especially graphs.
I’m not sure why NI allows you to place charts on a FPGA front panel.
It might work, but it will eat your resources like candy.
In your VI I see that you want to take a look at signals, stay away from the temptation to dump the signal data into a front panel element on the FPGA.
If you look at any of the LabVIEW Examples you will see that they almost never (I haven’t seen them all, so I can’t say none of them) use graphs on the front panel.
Follow the examples under Help>>Find examples.
Good Luck

Similar Messages

Error while executing WDA with PDf form

Hi,
when i'm executing WDA with PDF form i'm getting the following error message.
i've checked for Reader credential properties from Basis, they say evething is okay.
http://help.sap.com/saphelp_nw2004s/helpdata/en/56/f2c94a069f44a785b85748e11f82a0/content.htm
what must be theproblem.
Also when i execute other WDA application with PDF it is generating PDF .
pls help.
Error when processing your request
What has happened?
The URL http://dv1d11.corp.abc.pvt:8011/sap/bc/webdynpro/sap/zktest_pdf_try3/ was not called due to an error.
Note
The following error text was processed in the system D11 : WebDynpro Exception: ADS: com.adobe.ProcessingException: Could not retrieve a password for credential: ReaderRights(200,101).
The error occurred on the application server dv1d11_D11_11 and in the work process 2 .
The termination type was: RABAX_STATE
The ABAP call stack was:
Method: RAISE of program CX_WD_GENERAL=================CP
Method: CREATE_PDF of program CL_WD_ADOBE_SERVICES==========CP
Method: IF_WDR_VIEW_ELEMENT_ADAPTER~SET_CONTENT of program /1WDA/LADOBE==================CP
Method: IF_WDR_VIEW_ELEMENT_ADAPTER~SET_CONTENT of program /1WDA/LADOBE==================CP
Method: IF_WDR_VIEW_ELEMENT_ADAPTER~SET_CONTENT of program /1WDA/L8STANDARD==============CP
Method: IF_WDR_VIEW_ELEMENT_ADAPTER~SET_CONTENT of program /1WDA/L8STANDARD==============CP
Method: IF_WDR_VIEW_ELEMENT_ADAPTER~SET_CONTENT of program /1WDA/L7STANDARD==============CP
Method: CONV_VIEW_INTO_VE_ADAPTER_TREE of program CL_WDR_INTERNAL_WINDOW_ADAPTERCP
Method: SET_CONTENT_BY_WINDOW of program CL_WDR_INTERNAL_WINDOW_ADAPTERCP
Method: RENDER_WINDOWS of program CL_WDR_CLIENT_SSR=============CP
What can I do?
If the termination type was RABAX_STATE, then you can find more information on the cause of the termination in the system D11 in transaction ST22.
If the termination type was ABORT_MESSAGE_STATE, then you can find more information on the cause of the termination on the application server dv1d11_D11_11 in transaction SM21.
If the termination type was ERROR_MESSAGE_STATE, then you can search for more information in the trace file for the work process 2 in transaction ST11 on the application server dv1d11_D11_11 . In some situations, you may also need to analyze the trace files of other work processes.
If you do not yet have a user ID, contact your system administrator.
Error code: ICF-IE-http -c: 100 -u: 09039694 -l: E -s: D11 -i: dv1d11_D11_11 -w: 2 -d: 20081007 -t: 162655 -v: RABAX_STATE -e: UNCAUGHT_EXCEPTION
HTTP 500 - Internal Server Error
Your SAP Internet Communication Framework Team

When you tried other WDAs with PDFs, where they interactive PDFs? The reader rights are only needed for interactive PDFs.
>WebDynpro Exception: ADS: com.adobe.ProcessingException: Could not retrieve a password for credential: ReaderRights(200,101).
That error message would sure to seem to point that the credentials are not accessible to the user that ADS webservice call is being made by. That would certainly seem to me to point to a configuration problem at the Basis level.

Error when executing report with large data selection in Infoview

Hello,
This is regarding Error we are facing in BO system.
We have installed:
Business Object Enterprise XI 3.1
Crystal report 2008
When we are trying to execute report in BO INFOVIEW on production system, we are facing following error (After 10 mins of execution).
========================================================================================
Windows Internet Explorer
Stop running this script?
As script on this page is causing Internet Explorere to tun slowly.
If it continues to run, your computer might become
unresponsive.
========================================================================================
Please note: We are getting data via Crytal report. Only, execution in infoview is giving error.
If we are executing same report with less data(E.g a days data) then we are getting output in Infoview.
However, when we execute report with more data (6 months data) then we are getting attached error after 10 min of execution time.
Helpfull reply will be awarded.
Regards.
Edited by: Nirav Shah on Dec 14, 2010 6:19 AM

If it is indeed a server timeout issue, the following document might be usefull: http://www.sdn.sap.com/irj/boc/index?rid=/library/uuid/606e9338-bf3e-2b10-b7ab-ce76a7e34432
It's about Troubleshooting Time-outs in BusinessObjects Enterprise XI, but a lot is still applicable.
Hope this helps...
Martijn van Foeken
Focuzz BI Services
http://www.focuzz.nl
http://nl.linkedin.com/in/martijnvanfoeken
http://twitter.com/mfoeken

Error while executing Query with Variable.

Hi All,
I have written a query to fetch values from some user tables and sap tables. The query is as below.
select a.docentry,a.u_scname,e.block,e.[City],
e.[Country], e.[State1],
e.[StreetNo], e.[ZipCode],
e.[Building], e.[Cellular],a.[U_WONo], a.[U_DocDate],
a.[UserSign], b.[LineId], b.[U_Des],
b.[u_SDes], b.[U_UoM],
b.[U_Qty], b.[U_Rte],
b.[U_Tamt], a.[U_PrjName], a.[u_WO_PB],
a.[U_WO_UL], a.[U_WO_FC],
a.[U_WO_PYT], a.[U_WO_COP],
a.[U_WO_TRMT], a.[U_WO_DocSub],
a.[U_WO_ADV], a.[U_WO_OCondition],
a.[U_WO_PRPBY], a.[U_WO_RCMBY],e.[CntctPrsn],
(T4.[WhsName]+ '-' + T4.[Street] +'-' + T4.[Block]) as 'Work Address ',
T4.[Building], T4.[City],
T4.[ZipCode], T4.[U_PMCNT], T4.[WhsName], e.Taxid0
from [@e360_owor] as a join [@e360_wor1] as b
on a.docentry = b.docentry
left outer join
( select c.cardname,d.TaxId0,d.Taxid1, c.block, c.[City],
c.[Country], c.[State1],
c.[StreetNo], c.[ZipCode],
c.[Building], c.[Cellular], c.[CntctPrsn] from ocrd
as c join crd7 as d on c.cardcode = d.cardcode
where d.TaxId0 is not <b>null</b> ) as e
on
a.U_SCName = e.CardName
left outer join OWHS T4 on T4.[WhsName] = a.[U_Prj]
where
a.U_WONo = '[%0]'
In this code, when the variable is assigned to field U_WONo, then I get an error
Must Specify A Table To Select From. Statement 'Service Contractors' (OCTR) (s) could nto be prepared.
But when the values for variables are hard coded, the query executes.
I have been working on it from long time, but same error exists. Could anybody help resolve the same...
I am using SAP B1 2007 B, patch level 15.
Thanks in advance,
Regards
Rohan

The error messages may be misleading. With complicated queries with parameter request I frequently saw references to service contract (or something other).
Sometimes SBO does not manage correctly variables in complicated queries and there is a note about the workaround to solve the problem:[Note730960|https://websmp130.sap-ag.de/sap/bc/bsp/spn/sapnotes/index2.htm?numm=730960]

Error while executing bts_ConfigureBizTalkLogShipping with SQL Server 2012 and BTS 2013

Hi,
while configuring the DR site for Log shipping (http://msdn.microsoft.com/en-us/library/aa560961(v=bts.10).aspx)
exec bts_ConfigureBizTalkLogShipping @nvcDescription = '<MyLogShippingSolution>',
@nvcMgmtDatabaseName = '<BizTalkServerManagementDatabaseName>',
@nvcMgmtServerName = '<BizTalkServerManagementDatabaseServer>',
@SourceServerName = null, -- null indicates that this destination server restores all databases
@fLinkServers = 1 -- 1 automatically links the server to the management database
Getting errors while trying to execute the stored procedure "bts_ConfigureBizTalkLogShipping".
OLE DB provider "SQLNCLI11" for linked server "(null)" returned message "Login timeout expired".
OLE DB provider "SQLNCLI11" for linked server "(null)" returned message "A network-related or instance-specific error has occurred while establishing a connection to SQL Server. Server is not found or not accessible.
Check if instance name is correct and if SQL Server is configured to allow remote connections. For more information see SQL Server Books Online.".
Msg -1, Level 16, State 1, Line 0
SQL Server Network Interfaces: Error Locating Server/Instance Specified [xFFFFFFFF].
This is very strange because with the same server name (which I am passing in above query) I am able to connect from SQL Server Studio from DR site.
Any help would be much appreciated.
Thanks!
Regards,
Gautam
Thanks! Regards, Gautam

You need to check the DTC Connectivity between your DC and DR SQL Instance. The Linked Server requires DTC connectivity. Secondly this activity is better done from the SQL Server in question (the DC server in your case).
You can also manually add the Linked Server. Refer
http://msdn.microsoft.com/en-IN/library/ms188279(v=sql.105).aspx - Linking Servers and
http://msdn.microsoft.com/en-IN/library/ff772782(v=sql.105).aspx - Creating Linked Servers.
After having created the Linked Server(s) you can run the log shipping configuration again BUT using @fLinkServers = 0.
Regards.

Error when executing VI with "Invoke Node" in loop

Hello,
please check if this is possible what i am doing here or if there is a better way to do it.
The goal is to have a VI that i can start in TestStand which is then running in a loop until i set a global variable.
I do this currently with:
1.) Starting the VI with "Invoke Node" (see screenshot 01)
2.) This Vi is then running all the time in a loop until the global for exiting is True (screenshot 02)
3.) Then i have another VO to set the Quit-variable to true
Normally this works as it should, but sometimes i get the error-message:
Invoke Node in NameOfTheViCalledInTestStand.vi
Method Name: Run VI
VI Path: NameOfTheViThatContainsTheInvokeNode.vi
LabVIEW: Das VI befindet sich in einem für diese Operation unzulässigen Zustand.
The question is: what does this error mean and what better ways are there to do what i want to.
Perhaps for better understanding, the VI which runs in a loop executes dll-functions to enable and disable an ample-tower to make a light blinking.
And because there is no function "blink", i have to make it on off on off on off....
So the vi loops and makes on off until i say "quit" then blinking stops.
Thanks for any ideas
Attachments:
01_InvokeNode.jpg ‏8 KB
02_ViRunsInLoop.jpg ‏23 KB

I cant´t do this "Try changing the "Run" node
to "Wait Until Done" = True." because then the TestStand-Step is
hanging until the loop is finished.
I only want to start the "blinking" and the continue normally in the sequence.
To
avoid that the vi with the "Invoke Node" is started twice a have a vi
above it whick checks with the globalVariable "IsCurrentlyBlinking" if
the start is allowed.
If IsCurrentlyBlinking= True then nothing happens.
So normally it can´t happen that it starts twice. Only if the GlobalVariables are not correct.
The
variable "IsCurrentlyBlinking"is set to TRUE in the subvi before the
loop starts and after the loop is finished its set to FALSE in the
subvi.
Attachments:
03_CheckStart.jpg ‏16 KB

Error when executing Query with user date settings = mm/dd/yyyy

Hi all,
I created a remote cube with datasource = TCURR table with proper conversion of the date etc.
The query on top of this remote cube works fine if my user date settings is set to dd.mm.yyyy
But when a user in USA, with user date settings = mm/dd/yyyy, executes the same query, they get a message
SYST: Date 31/05/2006 not expected.
Message no. FGV004
The input variable on the Query is on 0CALMONTH.
This message appears immaterial of what calmonth input I give.
has anyone encountered this error? if yes, what could be the solution please?
thanks
Emmanuel

Hi,
This is in regard to the user settings maintained in transaction /nsu3.Please follow the below link.
http://web.mit.edu/sapr3/docs/webdocs/getstarted/gsSETTINGS.html
You need to change the settings as required.
Hope this helps.
Thank you,
Prem

Error while executing Initialize with Data Transfer for 0FI_GL_10

Hello All,
Post Pre prod refresh, our timestamp for the datasource 0FI_GL_10 got reset. Due to which our deltas did not bring any records to the BW system.
First we did an Initialize without data transfer for all the BW related datasources. The deltas were then set properly for all datasources except 0FI_GL_10.
We then raised a message to SAP and they suggested to run the 'Initialize with data transfer' for 0FI_GL_10 so that the timestamp is set and accordingly the deltas are fixed.
The issue now is we are getting the following error message while running INIT with data transfer.
Job terminated in source system --> Request set to red
Message no. RSM078
We have copied the data till July 1st week of 2011.
Please advice. The issue is very critical.
Thanks & Regards
Sneha

Hi Arvind
Thanks for your inputs.
Please find below the details of the short dump.
Runtime Errors         DBIF_RSQL_SQL_ERROR
Exception              CX_SY_OPEN_SQL_DB
Date and Time          09/07/2011 11:25:32
Short text
     SQL error in the database when accessing a table.
What can you do?
     Note which actions and input led to the error.
     For further help in handling the problem, contact your SAP administrator
     You can use the ABAP dump analysis transaction ST22 to view and manage
     termination messages, in particular for long term reference.
How to correct the error
     Database error text........: "ORA-01652: unable to extend temp segment by 128
      in tablespace PSAPTEMP"
     Internal call code.........: "[RSQL/FTCH/FAGLFLEXT ]"
     Please check the entries in the system log (Transaction SM21).
     If the error occures in a non-modified SAP program, you may be able to
     find an interim solution in an SAP Note.
     If you have access to SAP Notes, carry out a search with the following
     keywords:
     "DBIF_RSQL_SQL_ERROR" "CX_SY_OPEN_SQL_DB"
Information on where terminated
    Termination occurred in the ABAP program "GP_GLX_FAGLFLEXT" - in
     "FETCH_TO_ISTRUCTURE".
    The main program was "SBIE0001 ".
    In the source code you have the termination point in line 903
    of the (Include) program "GP_GLX_FAGLFLEXT".
    The program "GP_GLX_FAGLFLEXT" was started as a background job.
    Job Name....... "BIREQU_4N3PZQ12IA0X0PYGEA85IG39S"
    Job Initiator.. "BIWREMOTE"
    Job Number..... 11203300
    The termination is caused because exception "CX_SY_OPEN_SQL_DB" occurred in
    procedure "FETCH_TO_ISTRUCTURE" "(FORM)", but it was neither handled locally
     nor declared
    in the RAISING clause of its signature.
    The procedure is in program "GP_GLX_FAGLFLEXT "; its source code begins in line
    840 of the (Include program "GP_GLX_FAGLFLEXT ".

Error while executing mapping with 500 K records

Hi,
I have a mapping which has couple of transformation operators (Procedures) and some joiners and a splitter. The operation mode is set based fail over to row based. The target is set to update/insert. The target has about 20 fields.
I am loading about 500k records from source to target. I get the following error"
unable to extend segment by 4 in undo tablespace". My DBA has set 14 gigs space for the tablespace.
Can anybody provide pointers/ideas why this is happening and how can I overcome this.
My target and source are on Oracle 10g R2 and OWB is also 10g R2.
Thanks a lot in advance!
Maruthi

Hi, Maruthi!
Running OWB 10.1.0.4 on an Oracle 10gR1 database we had similar problems with UNDO tablespaces.
One reason could be that the UNDO tablespace is too small, but 500K rows with 20 columns do not seem very large to me (of course it depends on the column types, but I suppose they are mainly some NUMBERs, VARCHARs or DATEs).
You could use TOAD to have a quick look at the tablespaces or use the following statement:
SELECT *
FROM dba_data_files
WHERE tablespace_name = 'SYS_UNDO';
Another reason could be improper UNDO Management settings.
You should contact the DBA to check them to fit the application's requirements.
Regards,
Günther

Error when executing query with variables in excel

When I execute a query in excel, it gives some errors if it has some variables (From Date, To Date etc):
Error Specify a value for variable From Date
Error Specify a value for variable To Date
I need to execute the query and then save a view. I want to do this in excel as I am not able to save a view if I execute in a web browser.

Hi Sanjeev.
Of course Excel supports input of variable values.
What version of BW/BI both backend and frontend are you using?
Please check if you can execute the query in TA RSRT. You could try to generate the query again here.
Hope it helps.
BR
Stefan

Error when executing SAP_PD with rule for infotype

HI,
I am doing create organizational unit using SAP_PD generic service. I have defined a rule in HRASR_DT transaction to restrict address info type 1028. Infotype should trigger based on the conditions only. when i execute the complete form and click on thei am getting the error
"Field STEP_OBJECT_GUID is required for the evaluation of rule " ..Please advise me..
Thanks and Regards,
rama.

Hi Rama,
Thanks this helped me to solved the error.
I have problem while creating A 011 realtionship.
1) When I try to do cost center assignment A 011 relation ship using SAP_PD I have to enter coster center + controlling area on portal, otherwise I get error invalid cost center.
Rama,
By any changes have you worked on SAP_PA services, I have to do hiring of employee using SAP_PA services, but I get error u201CEnter personnel number error on portalu201D I have looked at the config done in standered Form Scenario (S_HRPA_US_REHIRE_1 in which SAP have done the hiring action config.) , but still same error.
Please guide.
Thanks & Regards,
Kavita Barde

FORMATTING ERROR when executing smartform with message SSFcomposer 159

Hi all,
I have created a custom smartform.When i execute it in tcode SMARTFORMS,i get the error "FORMATTING ERROR" "GRAPHIC CANNOT BE DISPLAYED".
I have a image file(LOGO) which is used in this Smartform.However this problem is faced only in the QUALITY system.In DEV system,the Smartform works fine.
PLease advise.
Thanks.

Hi,
is the logo also in the QTY system.
Che the name of the logo, then go in transaction SE78 and check if the logo exist.
Otherwise, create a transaport (always from SE78 trx) and transport the logo in the other systems.
Hope it helps
Bye
Andrea

How can I see error when execute UPDATE with BULK COLLECT

Hi
I have a code
   CURSOR c_renov_eleg IS
        SELECT t2.ROWID
          FROM mytable t2
     WHERE BLA BLA BLA
OPEN c_renov_eleg;
      LOOP
        FETCH c_renov_eleg BULK COLLECT
          INTO w_rowid LIMIT 1000;
        FORALL i IN 1 .. w_rowid.COUNT
          UPDATE mytable
             SET id_baixa_elegibilidade = K_SCNOB_BXA_RENOVACAO,
                  column01         = arr_ciclo(1),
                 dt_ultima_atualizacao = SYSDATE,
                 cd_usuario_atualizacao = USER
           WHERE ROWID = w_rowid(i);
        COMMIT;
        EXIT WHEN c_renov_eleg%NOTFOUND;
      END LOOP;How can I to sse when and where have some error ? , in Exception return what record ?

How can I to sse when and where have some error
?Have a look at
[url=http://download.oracle.com/docs/cd/B28359_01/appd
ev.111/b28370/tuning.htm#i49099]Handling FORALL
Exceptions (%BULK_EXCEPTIONS Attribute).btw. just never ever commit in a for loop ;)
(Tubby is just too fast ;))
Hi , thank all
btw. just never ever commit in a for loopWhen I must to COMMIT using BULK COLLECT ?

Journal Entry Error: -10([AJDT], line 4 with incoherent project/pl)

Hi,
A client is getting the above error on two different databases, one when doing a direct journal entry and the other while doing depreciation run. They are using projects and these have correctly been defined. Running on B1 2005 PL 11.
Has anyone ever come across this problem? Any suggestions/solution?
Regards,
Ann Muhoro.

From your error message: line 4 with incoherent project/pl, I would assume some of projects had been changed. Dig into the specific line detail to find anything different comparing with the current project.

Error while creating sales order with network/project

Dear All,
we are getting the following message while creating a sales order with assembly processing with network/project system .
The standard Network used as a reference contains assignments to a standard WBS. However you have maintained WBS assignments manually.which assignment should be used?
manually maint pre-defined
reward points are assured for valuable help.
thanking you
Best regards,
R.Srinivasan

Dear Murali,
Thankyou very much for your reply.We have checked for these things which you have mentioned.
ie
Assignment of Standard WBS in the Standard network and WBS Assignment of Operastional network.We are still getting this error.
Kindly let me know What are the other possibilities for this error.
Thanking you,
Best regards,
R.Srinivasan

Errors in executing VI with a project

Similar Messages

Maybe you are looking for