Faxing With A Calling Card

We don't have a long-distance carrier but make long distance calls via calling card. To send a long-distance fax, then, requires (1) a ten-digit call, (2) long pause, (3) multi-digit calling card number, (4) long pause, and (5) nine-digit called number. How can this be done?
thanks

Never mind. I got it in another forum. In the address book, enter the 800 number, comma, card number, comma, and distination number. Each comma is a one-second pause. I assume, but haven't tried it, that the destination number could be entered on a handset if it is not often faxed.

Similar Messages

Calling Card Problem: "Disconnected. Could not acquire credentials. The Rescue Gateway..."

Surely I cannot be the only LogMeInRescue customer experiencing the following issue with their Calling Cards failing to allow them to connect to their client computers. Ever since July of 2014, I experience this problem multiple times a week when trying to connect to client's computers who have had my Calling Card pre-installed on their computer. THE ERROR MESSAGEThe Calling Card displays the following message on the client's computer after they click on the Connect button:"Disconnected. Could not acquire credentials. The Rescue Gateway has refused the connection with the following message: Channel does not exist. It may have been recently deleted or modified." Here is a Screenshot that I posted on my website: http://www.pcgraphix.com/generator/assets/callingcard-disconnected_couldnotacquire.gif WHY THIS IS A MAJOR PROBLEM FOR ME-I have my calling card installed on HUNDREDS of computers and any delays in getting connected to a client computer costs me $. This has been a particularly major problem from me as I support people with very limited computer skills. The simple task of instructing them to go to logmein123.com and entering a 6 digit pin can LITERALLY take 15-30 minutes of my unbillable time! This can occur several times a day resulting in me me eating 1-2 hours of my time just trying to get connected to a client's computer! WHAT I HAVE DONE-I have called LogMeIn Tech support multiple times but they just seem to blow me off. When I first began calling support back in August 2014, they claimed they had never seen the problem. So I had them remote into computers that showed this calling card error. They gathered information and told me they would look into it. Well, 7 months later I still have this same recurring problem and they've never gotten back to me. So I continue to call them and complain. Recently, they finally admitted that it is a recognized issue but only affects a very small number of their customers and that they don't yet have a solution. So I'm reaching out to the community to see if anyone else is experiencing this problem. WHAT I HAVE EXPERIENCED/OBSERVED-I've been using LogMeIn Rescue since 2006 without any issues until July 2014. I believe the problem began on 7/16/14 when I generated a new calling card msi file (note that I have since generated new calling card msi files but the issue continues). About a month later (Aug 2014), I had experienced enough calling card issues that I began calling Logmein support for help. -This calling card issue occurs randomly and with different clients and with different Windows versions. -Once the problem occurs, the only fix is to completely uninstall my calling card from my client's computer and then re-installing the calling card using the msi file that I generated from my LogMeIn Rescue admin panel. Simply re-installing the calling card doesn't fix the problem...it must first be uninstalled and then re-installed. -The calling card can work fine on a client's computer on one day but then a day later it can fail to connect. -Some client's haven't experienced this problem at all. Some client's have experienced this problem on multiple occassions requiring that I do an uninstall/reinstall. -The issue has NEVER occurred when I first install my calling card. -I have noticed that if the calling card checks for and installs an update, the issue will often times occur. Therefore I believe it has something to do with the update that LogMeIn automatically pushes to the calling card. I instruct my clients to hit cancel if an update is available BUT oftens times they have already installed it. -I have generated new calling card msi files from my admin interface but this hasn't prevented the issue from occurring -

Glad to hear from someone else having this same problem! Supposedly there are a just a handful of us having this problem so I fear that LogMeIn developers aren't putting alot of effort into resolving this issue. I got hit first thing this morning on my first remote of the day with this assinine error message. It has happened several times in the past on this same customer's computer. It will work fine just after re-installing the calling card but then a week or so down the road it will fail again when I try to remote in. So **bleep** aggravating. So tired of eating hours every week walking customers through alternative ways of getting connected. When I say to customer, "ok, go to www.logmein123.com" and they reply "how do I do that" and I tell them to open their internet browser and all I get is dead silence....I know I'm about to eat more unbillable time! Bill

Im playin a game on my ipod called ck zombies i tryed to buy more credits for the game with my credit card and they said to go to itunes support to fix the problem what do i do?

im playing a game on my ipod touch called ck zombies and i was trying to buy some credit to play the game and they said i needed to go to itunes support to fix the problem where do i go to fix the purchases?

Check with your credit card company as to why its declining.

Using calling cards with the Iphone Question

Hi,
Just wanted to know if there is a way to add a calling card number passcode and than be able to dial the contact number. Previously I had the razr and nokia n8o and never had any issues, one way was to use the calling card number as a contact and than use touh tone to select a contact to call to send the number as tone and the other way was to add the whole number, calling card+ passcode+ contactno with pauses.
it seems i cant no niether with the iphone. is there any ideas or suggestions.
thanks.
VOIP would have been great but since not have to use this old method.

Please reply with at least a helpful answer soon! This is urgent!!

Hp photosmart 7520 - can fax, get calls but not receive fax with bundoed service and wireless router

I finally got the printer set up to my wireless router and am able to fax and receive calls but now I can't send a fax.
I have a bundled service phone, internet and cabl;e with voice mail.
I have reduced the number of rings to 2 and turned off automatic answer. ready to pull my hair out!!
HP tech service was no help and neither was the cable company. Got this far on my own but hit a wall!
any thoughts?

Hello @mull274 , and welcome to the HP Forums, I hope you enjoy your experience!
I see you are running into fax issues. I would like to help.
I would recommend performing a power reset on the printer. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I would also recommend this document on Fax Sending Fails Intermittently.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

I tried to purchase music at iTunes with the iTunes card I was given. I was able to redeem the amount and it shows on my apple Id I have $25 but it does not pay my purchase it will still go to my credit card and bill it. It did not give an option.

I tried to purchase music at iTunes with the iTunes card I was given. I was able to redeem the amount and it shows on my apple Id I have $25 but it does not pay my purchase it will still go to my credit card and bill it. It did not give an option.

If you were instructed to call them, then that's what you should do. They will probably need to verify your identity before helping you with the security question.

Problems with Fujifilm XD cards

Hi everyone!
I recently moved to my first Mac, and have been slowly introducing various peripherals, including my much-loved Fujifilm F30 camera.
While I haven't had many problems with the changeover, the F30 is proving a major stumbling point. Could anyone help me figure out how to negotiate this? I'd be really grateful for any help!
In short, when I use my MBP to delete photos from my XD card, it deletes the files happily. However, when I then insert the same XD card into my camera, it tells me that the card is full, and I cannot take any more photos.
Basically, I think I have compatability issues with the XD card and the MPB.
Longer version:
1) If I connect the F30 camera directly to my MBP, using the provided cable, the computer doesn't recognise it at all. It's not simply a case of not being able to read the files, or copy them across - it doesn't recognised that there is any camera attached. As it happens, my brother has the same camera, so I tried borrowing his cable (in case mine had become faulty). Same problem.
I checked the Fuji website, and I shouldn't need any drivers (I'm using OSX, 10.5.6).
I have never had any trouble with either cable or camera with previous laptop, and it still transfers happily to PCs. In other words, I don't think the camera is faulty. It seemed like some kind of compatability issue, but it was a real mystery.
2) I bought a USB card reader, to see if this would help. This is the beastie I chose:
http://www.amazon.co.uk/Fujifilm-USB-XD-Card-Reader/dp/B00172017W/ref=cmcr_pr_product_tophttp://www.amazon.co.uk/Fujifilm-USB-XD-Card-Reader/dp/B0017201 7W/ref=cm_cr_pr_producttop
At first: triumph! MPB immediately detected the USB, and I could transfer the photos on my XD card easily to my hard-drive. No problem opening or manipulating the files, either - I've been playing with them on Picasa, and all is well with the .jpgs - no corruptions that I can see.
However, when I try to delete the photos from my XD card, something goes awry.
I had transferred the .jpgs in question to my hard-drive, then returned to the USB to delete the original files. This seemed straighforward, and was easily done (with the files moved to trash). But - here's the weirdness - when I insert the XD card to my camera:
a) the files are gone (hurray!)
b) there is no free space.
In other words, having deleted all the files on my 512MB XD card, the camera told me that my XD card was full.
I used the camera's own buttons to review the XD card - i.e. inserted the XD card into the F30, and pressed 'play' to open up the memory. There was nothing there. The camera could not show me any photographs.
So I now have the very strange situation of:
- having no photographs on the XD memory
- being told that the card is full, and I cannot take any more photos.
Help?!
Some more info:
As it happens, I have a second XD card, a 1GB XD. I tried an experiment. I noted how many photographs were left on the card: 63 shots.
I inserted the card into my USB card reader, deleted c.20 photographs already backed up elsewhere, and reinserted the XD card into my camera.
There were still only 63 shots left.
I used the camera's own interface to delete a shot. Remaining space: 64 shots.
In other words, only those files deleted by my Mac are affected.
Why not just use the camera to delete files, then? Well, in the short-term, it doesn't help my poor, borked 512MB XD card. I have no files to delete, and so I can't convince my camera that there is, in fact, room. Any files I deleted seems to be dead space now, with no clear way to retrieve it.
In the long-term, though, this is troubling. Yes, I could buy more XD cards (which aren't cheap, but let's just go with this). I could decide that the 512 MB card is now dead, and the 1GB card somewhat damaged. I could restrict myself to only delete photos on the F30 itself.
However, this is a major disappointment, and very frustrating. I take hundreds of photos, and to go through them one by one, pressing 'delete, ok' for each of them in turn would be hugely time intensive (and draining on battery power, while travelling).
I would dearly love to find a way to do negotiate this - any ideas? It feels like this is a formatting issue, but I don't know for sure. Has anyone else used an F30 with their Mac? Any solutions?

Short answer: Empty the trash with the card reader connected to your Mac.
Longer answer: Deleting files is a two-step process - move the file(s) to the trash, then Empty the trash (Finder > File menu) to free up the space. The 'deleted' files are stored in an invisible folder (called .Trashes) at the root level of the drive/card the files were deleted from. Since the folder is invisible and the pics in it are not in the 'normal' file structure the camera expects, the camera does not see them. If you eject/unmount the drive, those files are not deleted. You must empty the trash with the drive/card connected. One thing you may note - if you have an empty trash can icon in the dock (i.e., you've emptied the trash without the card reader connected), then you connect the card reader with your 'borked' card, the trash can icon will change to a full trash can.
As a side note, I have a couple of Olympus cameras that use xD cards, I have some Olympus-branded and some Fuji-branded cards, up to 2 GB - all the cards work just fine with my MBP; I rarely connect the camera itself (can't even remember the last time) but I have used USB readers and now an ExpressCard reader.

HT3702 I have an order that has not been completed and the old card no longer exists and I want to pay with my new card. the order is MHBG5FL5DH How do I delete the restriction in iTunes

I have an order that has not been completed and the old card no longer exists and I want to pay with my new card. the order is MHBG5FL5DHHow do I delete the restriction in iTunes

You need to ask Apple to reset your security questions. To do this, click here and pick a method; if that page doesn't list one for your country or you're unable to call, fill out and submit this form.
(122986)

Please! Help me with my SIM card problem!

When I first bought the Blackberry Flip 8220, I was constantly having a problem with my SIM card and the signals. My signal would constantly drop down to none and would go into SOS mode. Not only that, but it would also say either "SIM Card Error,""Invalid SIM Card," or "Insert SIM Card." So, the RIM sent me a new replacement for the cellphone. For the first few days, it worked just fine but, as the time passed by, the phone started to have the similar problem. What's worse is that as the time passed, the more problem started to show up! Now, my side buttons aren't functioning and the rate of my phone experiencing the problem with the SIM card and the signals, similar to the ones mentions above, has risen drastically. For now, the side buttons aren't my priority but what I would like to find out is how come my phone is experiencing such problem with the SIM card and how I can fix it. Please, help me! Due to this problem, I can't even receive the international calls.

Hi and Welcome to the Forums!
I don't believe that RIM issues SIMs...the carriers issue the SIM cards since these activate your phone on their network. RIM doesn't care what network you use...but the carriers do
So, what I'd suggest is that you go see your carrier and find out what's going on with the bad SIM. It is also possible that the device itself has a problem with the SIM card contacts...in which case the advice is the same, your carrier provides your service, so going to see them is the right thing to do.
Good luck and let us know how it goes!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Contact names not showing with incoming calls!!!

Hi all,
I just got my E71-1 yesterday and upgraded from a very effiecient E61i....everything was going smooth until all of a sudden, contact names stopped appearing with incoming calls and SMS's.
I went through the forums searching for a solutions and apparently alot of people experienced the same thing.....except in my case, I do not have any duplicate names or numbers!!!!
Any ideas what could solve this???

There is a fix for it but you won't like it. I have tried it a few times and it always works but it involves a lot of work. This is what you do.
1. Make a backup of nothing else but your contacts only.
2. Delete all your contacts from both phone and sim card.
3. Start by entering the troublesome contacts from scratch making sure not to duplicate any numbers.
4. Now get those people to ring you to make sure that your CLI is working fine.
5. If it works then start entering the rest of the numbers, once again making sure there is no duplication whatsoever.
6. If it doesn't work, just restore the backup you made of your contacts.
I am fairly sure it will work, but just in case it doesn't you can always restore your backup and you are back to square one.

"There is a problem with the SIM card in your iPhone"

I'm getting this error when I try to activate my new iPhone 4 through iTunes:
"*There is a problem with the SIM card in your iPhone.*
To activate your iPhone with this account, you will need a new, unactivated SIM card. Please use the SIM card that was provided with your new iPhone. If you are using the new SIM card, and are unable to complete activation, you can go to an Apple Retail Store or an AT&T company owned retail store to request an unactivated SIM. If you would prefer to have a replacement SIM card sent to you via overnight mail, please call us at 1-800-MY-APPLE. We apologize for the inconvenience this has caused."
Now I've already been to AT&T and nothing they could do with the account settings would work, in fact they had never seen the issue before. They gave me a new SIM card and that did nothing as well. Finally they tried out a different SIM tray, and that still didn't work. I have a Genius Bar appointment at the Apple Store tomorrow, but I was wondering if anyone else has this problem. Do you think that the SIM reader inside the iPhone 4 is broken?

I solved a problem I had with activating my iPhone although the error message was different from yours.
I got the message "There is something wrong with your iPhone and it cannot be activated, please bring it to your nearest Apple service".
Via a Chinese forum I found out its the SIM card witch is the problem. If the serial number of the SIM has a "letter" in it it won't work. If only numbers it will work.
I now tried it with 2 SIM cards with letters and got the message over and over again. Than tried with my only numbers SIM card and it activated instantly.

Set up prepaid calling card for international calls?

I have a prepaid calling card that I use for calling international. The way it works is that I have to call a 866 number, followed by entering a 10 digit code, and then proceed to calling the actual number (with international prefix codes). Is there a way to set this up as international call default so that I do not have to modify all my international contact's phone numbers to include this procedure?
Thanks.
K

speed dial: Your smartphone can store nine
phone numbers that you can call
with a single keypress. To store a
speed dial number, touch Phone
> Menu > Speed dial setup, and
insert a number in an empty speed
dial slot.
To call a speed dial number, touch
and hold the single-digit speed dial
number in the dialer screen.

How can I set up a calling card on speed dialing?

I use a company calling card for international dialing. How can I set up a speed dial for the dial number and the password with a pause in between for the international number? Any clues?

speed dial: Your smartphone can store nine
phone numbers that you can call
with a single keypress. To store a
speed dial number, touch Phone
> Menu > Speed dial setup, and
insert a number in an empty speed
dial slot.
To call a speed dial number, touch
and hold the single-digit speed dial
number in the dialer screen.

[SOLVED] kernel crash with PCI wifi card

HI,
I id install and start to use arch just two weeks ago :-)
I was able to solve problems until now.
I am not sure if this is problem of arch kernel, maybe it will be general.
I did insert PCI wifi card to my PC with arch. Card is Z-COM XI-626 : LAST LINE:
lspci
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5)
00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b5)
00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5)
00:1c.6 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 (rev b5)
00:1c.7 PCI bridge: Intel Corporation 82801 PCI Bridge (rev b5)
00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation H67 Express Chipset Family LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
03:00.0 IDE interface: VIA Technologies, Inc. VT6415 PATA IDE Host Controller
04:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
06:00.0 PCI bridge: ASMedia Technology Inc. ASM108x PCIe to PCI Bridge Controller (rev 01)
07:00.0 Network controller: Intersil Corporation ISL3874 [Prism 2.5]/ISL3872 [Prism 3] (rev 01)
It start to work very nicely, I could connect to the network with NetworkManager in gnome.
BUT
after while connection is not working.
the is in message LOG:
Dec 6 07:53:09 localhost NetworkManager[686]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) scheduled...
Dec 6 07:53:09 localhost NetworkManager[686]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) complete.
Dec 6 07:53:09 localhost NetworkManager[686]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) started...
Dec 6 07:53:10 localhost NetworkManager[686]: <info> (wlan0): device state change: ip-config -> activated (reason 'none') [70 100 0]
Dec 6 07:53:10 localhost NetworkManager[686]: <info> Policy set 'Auto moje_wifi' (wlan0) as default for IPv4 routing and DNS.
Dec 6 07:53:10 localhost NetworkManager[686]: <info> Activation (wlan0) successful, device activated.
Dec 6 07:53:10 localhost NetworkManager[686]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) complete.
Dec 6 07:53:10 localhost dbus[661]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper)
Dec 6 07:53:10 localhost dbus[661]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher'
Dec 6 08:02:58 localhost kernel: [ 1889.872241] Pid: 0, comm: swapper Tainted: G C 3.1.4-1-ARCH #1
Dec 6 08:02:58 localhost kernel: [ 1889.872243] Call Trace:
Dec 6 08:02:58 localhost kernel: [ 1889.872244] <IRQ> [<ffffffff810c6cfd>] __report_bad_irq+0x3d/0xe0
Dec 6 08:02:58 localhost kernel: [ 1889.872252] [<ffffffff810c713d>] note_interrupt+0x14d/0x210
Dec 6 08:02:58 localhost kernel: [ 1889.872255] [<ffffffff810c5079>] handle_irq_event_percpu+0xc9/0x2a0
Dec 6 08:02:58 localhost kernel: [ 1889.872257] [<ffffffff810c5298>] handle_irq_event+0x48/0x70
Dec 6 08:02:58 localhost kernel: [ 1889.872259] [<ffffffff810c7a7a>] handle_fasteoi_irq+0x5a/0xe0
Dec 6 08:02:58 localhost kernel: [ 1889.872262] [<ffffffff81016992>] handle_irq+0x22/0x40
Dec 6 08:02:58 localhost kernel: [ 1889.872265] [<ffffffff8140d01a>] do_IRQ+0x5a/0xe0
Dec 6 08:02:58 localhost kernel: [ 1889.872268] [<ffffffff81409c6e>] common_interrupt+0x6e/0x6e
Dec 6 08:02:58 localhost kernel: [ 1889.872269] <EOI> [<ffffffff8131d3aa>] ? poll_idle+0x3a/0x80
Dec 6 08:02:58 localhost kernel: [ 1889.872273] [<ffffffff8131d383>] ? poll_idle+0x13/0x80
Dec 6 08:02:58 localhost kernel: [ 1889.872275] [<ffffffff8131d756>] cpuidle_idle_call+0xc6/0x350
Dec 6 08:02:58 localhost kernel: [ 1889.872277] [<ffffffff81013229>] cpu_idle+0xc9/0x120
Dec 6 08:02:58 localhost kernel: [ 1889.872280] [<ffffffff813e6912>] rest_init+0x96/0xa4
Dec 6 08:02:58 localhost kernel: [ 1889.872282] [<ffffffff8194fc15>] start_kernel+0x3bf/0x3cc
Dec 6 08:02:58 localhost kernel: [ 1889.872285] [<ffffffff8194f347>] x86_64_start_reservations+0x132/0x136
Dec 6 08:02:58 localhost kernel: [ 1889.872287] [<ffffffff8194f140>] ? early_idt_handlers+0x140/0x140
Dec 6 08:02:58 localhost kernel: [ 1889.872289] [<ffffffff8194f44d>] x86_64_start_kernel+0x102/0x111
Dec 6 08:03:05 localhost NetworkManager[686]: <info> (wlan0): roamed from BSSID 00:19:0A:01:1A:66 (moje_wifi) to (none) ((none))
Dec 6 08:03:05 localhost kernel: [ 1896.943757] wlan0: interrupt delivery does not seem to work
Dec 6 08:03:07 localhost kernel: [ 1898.942477] wlan0: interrupt delivery does not seem to work
Dec 6 08:03:10 localhost kernel: [ 1902.180399] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:12 localhost kernel: [ 1904.179118] wlan0: interrupt delivery does not seem to work
Dec 6 08:03:14 localhost kernel: [ 1906.177838] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:16 localhost kernel: [ 1908.176557] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:18 localhost kernel: [ 1910.175277] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:20 localhost kernel: [ 1912.173997] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:22 localhost kernel: [ 1914.172716] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:24 localhost kernel: [ 1916.171436] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:26 localhost kernel: [ 1918.170157] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:28 localhost kernel: [ 1920.168875] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:30 localhost kernel: [ 1922.167595] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:32 localhost kernel: [ 1924.166315] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:32 localhost kernel: [ 1924.279547] ------------[ cut here ]------------
Dec 6 08:03:32 localhost kernel: [ 1924.279553] WARNING: at net/sched/sch_generic.c:255 dev_watchdog+0x257/0x260()
Dec 6 08:03:32 localhost kernel: [ 1924.279555] Hardware name: System Product Name
Dec 6 08:03:32 localhost kernel: [ 1924.279556] NETDEV WATCHDOG: wifi0 (hostap_pci): transmit queue 0 timed out
Dec 6 08:03:32 localhost kernel: [ 1924.279558] Modules linked in: fuse ext2 mbcache snd_hda_codec_hdmi orinoco_pci orinoco cfg80211 snd_hda_codec_realtek i915 drm_kms_helper drm i2c_i801 hostap_pci hostap i2c_algo_bit i2c_core eeepc_wmi asus_wmi sparse_keymap rfkill psmouse pci_hotplug serio_raw snd_hda_intel mei(C) snd_hda_codec iTCO_wdt iTCO_vendor_support snd_hwdep snd_pcm snd_timer snd evdev r8169 mii pcspkr intel_agp intel_gtt button video lib80211 wmi processor soundcore snd_page_alloc btrfs zlib_deflate crc32c libcrc32c hid_a4tech usbhid hid sd_mod ahci pata_acpi libahci pata_via libata xhci_hcd ehci_hcd scsi_mod usbcore
Dec 6 08:03:32 localhost kernel: [ 1924.279599] Pid: 0, comm: swapper Tainted: G C 3.1.4-1-ARCH #1
Dec 6 08:03:32 localhost kernel: [ 1924.279600] Call Trace:
Dec 6 08:03:32 localhost kernel: [ 1924.279602] <IRQ> [<ffffffff81061b9f>] warn_slowpath_common+0x7f/0xc0
Dec 6 08:03:32 localhost kernel: [ 1924.279610] [<ffffffff81025047>] ? intel_pmu_enable_all+0xa7/0x110
Dec 6 08:03:32 localhost kernel: [ 1924.279612] [<ffffffff81061c96>] warn_slowpath_fmt+0x46/0x50
Dec 6 08:03:32 localhost kernel: [ 1924.279615] [<ffffffff8107e472>] ? __queue_work+0xe2/0x490
Dec 6 08:03:32 localhost kernel: [ 1924.279617] [<ffffffff81364377>] dev_watchdog+0x257/0x260
Dec 6 08:03:32 localhost kernel: [ 1924.279620] [<ffffffff81071e61>] run_timer_softirq+0x131/0x440
Dec 6 08:03:32 localhost kernel: [ 1924.279622] [<ffffffff81364120>] ? qdisc_reset+0x50/0x50
Dec 6 08:03:32 localhost kernel: [ 1924.279624] [<ffffffff8101c139>] ? read_tsc+0x9/0x20
Dec 6 08:03:32 localhost kernel: [ 1924.279626] [<ffffffff810691c0>] __do_softirq+0xb0/0x270
Dec 6 08:03:32 localhost kernel: [ 1924.279629] [<ffffffff81096158>] ? tick_dev_program_event+0x48/0x110
Dec 6 08:03:32 localhost kernel: [ 1924.279631] [<ffffffff8109623f>] ? tick_program_event+0x1f/0x30
Dec 6 08:03:32 localhost kernel: [ 1924.279634] [<ffffffff8140c76c>] call_softirq+0x1c/0x30
Dec 6 08:03:32 localhost kernel: [ 1924.279637] [<ffffffff81016a15>] do_softirq+0x65/0xa0
Dec 6 08:03:32 localhost kernel: [ 1924.279639] [<ffffffff810696ce>] irq_exit+0x9e/0xc0
Dec 6 08:03:32 localhost kernel: [ 1924.279641] [<ffffffff8140d10e>] smp_apic_timer_interrupt+0x6e/0x99
Dec 6 08:03:32 localhost kernel: [ 1924.279643] [<ffffffff8140afde>] apic_timer_interrupt+0x6e/0x80
Dec 6 08:03:32 localhost kernel: [ 1924.279644] <EOI> [<ffffffff81279e9b>] ? intel_idle+0xcb/0x120
Dec 6 08:03:32 localhost kernel: [ 1924.279649] [<ffffffff81279e7d>] ? intel_idle+0xad/0x120
Dec 6 08:03:32 localhost kernel: [ 1924.279651] [<ffffffff8131d756>] cpuidle_idle_call+0xc6/0x350
Dec 6 08:03:32 localhost kernel: [ 1924.279654] [<ffffffff81013229>] cpu_idle+0xc9/0x120
Dec 6 08:03:32 localhost kernel: [ 1924.279657] [<ffffffff813e6912>] rest_init+0x96/0xa4
Dec 6 08:03:32 localhost kernel: [ 1924.279659] [<ffffffff8194fc15>] start_kernel+0x3bf/0x3cc
Dec 6 08:03:32 localhost kernel: [ 1924.279662] [<ffffffff8194f347>] x86_64_start_reservations+0x132/0x136
Dec 6 08:03:32 localhost kernel: [ 1924.279664] [<ffffffff8194f140>] ? early_idt_handlers+0x140/0x140
Dec 6 08:03:32 localhost kernel: [ 1924.279666] [<ffffffff8194f44d>] x86_64_start_kernel+0x102/0x111
Dec 6 08:03:32 localhost kernel: [ 1924.279668] ---[ end trace 6f3b132eb24e1d2e ]---
Dec 6 08:03:32 localhost kernel: [ 1924.279669] wifi0 Tx timed out! Resetting card
Dec 6 08:03:32 localhost kernel: [ 1924.279694] hostap_pci: wifi0: resetting card
Dec 6 08:03:34 localhost kernel: [ 1926.278267] wifi0 Tx timed out! Resetting card
Dec 6 08:03:36 localhost kernel: [ 1928.163754] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:36 localhost kernel: [ 1928.276987] wifi0 Tx timed out! Resetting card
Dec 6 08:03:38 localhost kernel: [ 1930.162473] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:38 localhost kernel: [ 1930.222552] hostap_pci: wifi0: already resetting card - ignoring reset request
Dec 6 08:03:38 localhost kernel: [ 1930.262615] hostap_pci: wifi0: already resetting card - ignoring reset request
Dec 6 08:03:38 localhost kernel: [ 1930.262619] wifi0: Port type setting to 1 failed
Dec 6 08:03:38 localhost kernel: [ 1930.275703] wifi0 Tx timed out! Resetting card
Dec 6 08:03:40 localhost kernel: [ 1932.261129] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:40 localhost kernel: [ 1932.261131] wifi0: MAC port 0 enabling failed
Dec 6 08:03:40 localhost kernel: [ 1932.261150] hostap_pci: wifi0: resetting card
Dec 6 08:03:43 localhost kernel: [ 1934.463052] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:43 localhost kernel: [ 1934.463064] hostap_pci: wifi0: already resetting card - ignoring reset request
Dec 6 08:03:45 localhost kernel: [ 1936.461771] wifi0: interrupt delivery does not seem to work
Dec 6 08:03:45 localhost kernel: [ 1936.501864] hostap_pci: wifi0: already resetting card - ignoring reset request
Dec 6 08:03:45 localhost kernel: [ 1936.501866] wifi0: Port type setting to 1 failed
Dec 6 08:03:45 localhost kernel: [ 1936.521925] wifi0: MAC port 0 enabling failed
Dec 6 08:04:13 localhost kernel: [ 1964.923031] hostap_pci: wlan0: resetting card
Dec 6 08:04:15 localhost kernel: [ 1967.125469] wlan0: interrupt delivery does not seem to work
Dec 6 08:04:15 localhost kernel: [ 1967.125474] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:04:17 localhost kernel: [ 1969.124179] wifi0: interrupt delivery does not seem to work
Dec 6 08:04:17 localhost kernel: [ 1969.164257] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:04:17 localhost kernel: [ 1969.164259] wlan0: Port type setting to 1 failed
Dec 6 08:04:17 localhost kernel: [ 1969.184273] wlan0: MAC port 0 enabling failed
Dec 6 08:06:13 localhost kernel: [ 2084.846529] hostap_pci: wlan0: resetting card
Dec 6 08:06:15 localhost kernel: [ 2087.048638] wlan0: interrupt delivery does not seem to work
Dec 6 08:06:15 localhost kernel: [ 2087.048649] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:06:17 localhost kernel: [ 2089.047356] wifi0: interrupt delivery does not seem to work
Dec 6 08:06:17 localhost kernel: [ 2089.087406] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:06:17 localhost kernel: [ 2089.087407] wlan0: Port type setting to 1 failed
Dec 6 08:06:17 localhost kernel: [ 2089.107404] wlan0: MAC port 0 enabling failed
Dec 6 08:08:13 localhost kernel: [ 2204.769302] hostap_pci: wlan0: resetting card
Dec 6 08:08:15 localhost kernel: [ 2206.971827] wlan0: interrupt delivery does not seem to work
Dec 6 08:08:15 localhost kernel: [ 2206.971832] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:08:17 localhost kernel: [ 2208.970532] wifi0: interrupt delivery does not seem to work
Dec 6 08:08:17 localhost kernel: [ 2209.010630] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:08:17 localhost kernel: [ 2209.010634] wlan0: Port type setting to 1 failed
Dec 6 08:08:19 localhost kernel: [ 2211.009274] wlan0: interrupt delivery does not seem to work
Dec 6 08:08:19 localhost kernel: [ 2211.009275] wlan0: MAC port 0 enabling failed
Dec 6 08:10:13 localhost kernel: [ 2324.691574] hostap_pci: wlan0: resetting card
Dec 6 08:10:15 localhost kernel: [ 2326.891711] wlan0: interrupt delivery does not seem to work
Dec 6 08:10:15 localhost kernel: [ 2326.891716] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:10:17 localhost kernel: [ 2328.890393] wifi0: interrupt delivery does not seem to work
Dec 6 08:10:17 localhost kernel: [ 2328.930472] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:10:17 localhost kernel: [ 2328.930473] wlan0: Port type setting to 1 failed
Dec 6 08:10:17 localhost kernel: [ 2328.950482] wlan0: MAC port 0 enabling failed
Dec 6 08:12:13 localhost kernel: [ 2444.616669] hostap_pci: wlan0: resetting card
Dec 6 08:12:15 localhost kernel: [ 2446.818212] wlan0: interrupt delivery does not seem to work
Dec 6 08:12:15 localhost kernel: [ 2446.818218] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:12:17 localhost kernel: [ 2448.816887] wifi0: interrupt delivery does not seem to work
Dec 6 08:12:17 localhost kernel: [ 2448.856917] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:12:17 localhost kernel: [ 2448.856919] wlan0: Port type setting to 1 failed
Dec 6 08:12:17 localhost kernel: [ 2448.876938] wlan0: MAC port 0 enabling failed
Dec 6 08:14:13 localhost kernel: [ 2564.540113] hostap_pci: wlan0: resetting card
Dec 6 08:14:15 localhost kernel: [ 2566.741388] wlan0: interrupt delivery does not seem to work
Dec 6 08:14:15 localhost kernel: [ 2566.741394] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:14:17 localhost kernel: [ 2568.740062] wifi0: interrupt delivery does not seem to work
Dec 6 08:14:17 localhost kernel: [ 2568.780120] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:14:17 localhost kernel: [ 2568.780121] wlan0: Port type setting to 1 failed
Dec 6 08:14:17 localhost kernel: [ 2568.800135] wlan0: MAC port 0 enabling failed
Dec 6 08:16:13 localhost kernel: [ 2684.463514] hostap_pci: wlan0: resetting card
Dec 6 08:16:15 localhost kernel: [ 2686.664525] wlan0: interrupt delivery does not seem to work
Dec 6 08:16:15 localhost kernel: [ 2686.664530] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:16:17 localhost kernel: [ 2688.663241] wifi0: interrupt delivery does not seem to work
Dec 6 08:16:17 localhost kernel: [ 2688.703314] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:16:17 localhost kernel: [ 2688.703315] wlan0: Port type setting to 1 failed
Dec 6 08:16:17 localhost kernel: [ 2688.723340] wlan0: MAC port 0 enabling failed
Dec 6 08:18:13 localhost kernel: [ 2804.386357] hostap_pci: wlan0: resetting card
Dec 6 08:18:15 localhost kernel: [ 2806.587699] wlan0: interrupt delivery does not seem to work
Dec 6 08:18:15 localhost kernel: [ 2806.587704] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:18:17 localhost kernel: [ 2808.586422] wifi0: interrupt delivery does not seem to work
Dec 6 08:18:17 localhost kernel: [ 2808.626468] hostap_pci: wlan0: already resetting card - ignoring reset request
Dec 6 08:18:17 localhost kernel: [ 2808.626471] wlan0: Port type setting to 1 failed
Dec 6 08:18:19 localhost kernel: [ 2810.625118] wlan0: interrupt delivery does not seem to work
Dec 6 08:18:19 localhost kernel: [ 2810.625121] wlan0: MAC port 0 enabling failed
please, have anybody idea what is wrong?
thanks for help / tips ...
Last edited by jancici (2012-03-21 08:47:06)

okay, I did blacklist hostap_pci, I did find out that with orinoco_pci module it is more stable
BUT
sometimes it hang up with same error message
Dec 6 23:03:45 localhost kernel: [ 2465.908317] ------------[ cut here ]------------
Dec 6 23:03:45 localhost kernel: [ 2465.908324] WARNING: at net/sched/sch_generic.c:255 dev_watchdog+0x257/0x260()
Dec 6 23:03:45 localhost kernel: [ 2465.908326] Hardware name: System Product Name
Dec 6 23:03:45 localhost kernel: [ 2465.908328] NETDEV WATCHDOG: eth1 (orinoco_pci): transmit queue 0 timed out
Dec 6 23:03:45 localhost kernel: [ 2465.908329] Modules linked in: fuse ext2 mbcache snd_hda_codec_hdmi snd_hda_codec_realtek orinoco_pci orinoco r8169 cfg80211 mii
i915 drm_kms_helper drm snd_hda_intel evdev snd_hda_codec mei(C) i2c_algo_bit rfkill intel_agp psmouse wmi i2c_i801 i2c_core intel_gtt snd_hwdep snd_pcm button proc
essor video snd_timer snd soundcore snd_page_alloc btrfs zlib_deflate crc32c libcrc32c hid_a4tech usbhid hid sd_mod ahci pata_acpi libahci xhci_hcd pata_via libata e
hci_hcd scsi_mod usbcore
Dec 6 23:03:45 localhost kernel: [ 2465.908365] Pid: 0, comm: kworker/0:1 Tainted: G C 3.1.4-1-ARCH #1
Dec 6 23:03:45 localhost kernel: [ 2465.908366] Call Trace:
Dec 6 23:03:45 localhost kernel: [ 2465.908368] <IRQ> [<ffffffff81061b9f>] warn_slowpath_common+0x7f/0xc0
Dec 6 23:03:45 localhost kernel: [ 2465.908375] [<ffffffff81025047>] ? intel_pmu_enable_all+0xa7/0x110
Dec 6 23:03:45 localhost kernel: [ 2465.908378] [<ffffffff81061c96>] warn_slowpath_fmt+0x46/0x50
Dec 6 23:03:45 localhost kernel: [ 2465.908381] [<ffffffff810f1743>] ? perf_ctx_unlock+0x23/0x30
Dec 6 23:03:45 localhost kernel: [ 2465.908383] [<ffffffff81364377>] dev_watchdog+0x257/0x260
Dec 6 23:03:45 localhost kernel: [ 2465.908386] [<ffffffff81071e61>] run_timer_softirq+0x131/0x440
Dec 6 23:03:45 localhost kernel: [ 2465.908388] [<ffffffff81364120>] ? qdisc_reset+0x50/0x50
Dec 6 23:03:45 localhost kernel: [ 2465.908390] [<ffffffff8101c139>] ? read_tsc+0x9/0x20
Dec 6 23:03:45 localhost kernel: [ 2465.908392] [<ffffffff810691c0>] __do_softirq+0xb0/0x270
Dec 6 23:03:45 localhost kernel: [ 2465.908395] [<ffffffff81096158>] ? tick_dev_program_event+0x48/0x110
Dec 6 23:03:45 localhost kernel: [ 2465.908397] [<ffffffff8109623f>] ? tick_program_event+0x1f/0x30
Dec 6 23:03:45 localhost kernel: [ 2465.908400] [<ffffffff8140c76c>] call_softirq+0x1c/0x30
Dec 6 23:03:45 localhost kernel: [ 2465.908403] [<ffffffff81016a15>] do_softirq+0x65/0xa0
Dec 6 23:03:45 localhost kernel: [ 2465.908404] [<ffffffff810696ce>] irq_exit+0x9e/0xc0
Dec 6 23:03:45 localhost kernel: [ 2465.908407] [<ffffffff8140d10e>] smp_apic_timer_interrupt+0x6e/0x99
Dec 6 23:03:45 localhost kernel: [ 2465.908409] [<ffffffff8140afde>] apic_timer_interrupt+0x6e/0x80
Dec 6 23:03:45 localhost kernel: [ 2465.908410] <EOI> [<ffffffff81279e9b>] ? intel_idle+0xcb/0x120
Dec 6 23:03:45 localhost kernel: [ 2465.908415] [<ffffffff81279e7d>] ? intel_idle+0xad/0x120
Dec 6 23:03:45 localhost kernel: [ 2465.908417] [<ffffffff8131d756>] cpuidle_idle_call+0xc6/0x350
Dec 6 23:03:45 localhost kernel: [ 2465.908419] [<ffffffff81013229>] cpu_idle+0xc9/0x120
Dec 6 23:03:45 localhost kernel: [ 2465.908422] [<ffffffff813f8944>] start_secondary+0x202/0x209
Dec 6 23:03:45 localhost kernel: [ 2465.908424] ---[ end trace 58cac98ca8b4102b ]---
Dec 6 23:03:45 localhost kernel: [ 2465.908433] eth1: Tx timeout! ALLOCFID=0128, TXCOMPLFID=03eb, EVSTAT=808b
maybe I need some more modern card, something with atheros chipset ...

AAA Radius Authentication for Calling Card Platform

Hi,
I am using AS5350 and I am using it for calling card application using Clear Box as my RADIUS Server for AAA. My question now, how would I know if cisco is sending the dtmf for "enter card number.au" on the RADIUS server ? Does the card number included on the VSA ? below are my configurations and the debug info. The problem here is that the card number that I entered doesn't able to match against the configuration on my Clear Box/SQL Database. I want to know what should I expect from CiscoAS5350 to send a vsa for enter_card_number ?
aaa new-model
aaa group server radius ClearBox
server 192.168.1.1 auth-port 1812 acct-port 1813
aaa authentication login default local
aaa authentication login h323 group ClearBox
aaa authorization exec h323 group ClearBox
aaa accounting exec default start-stop group ClearBox
aaa accounting network default start-stop group ClearBox
aaa accounting connection h323 start-stop group ClearBox
aaa session-id unique
radius-server host 192.168.1.1 auth-port 1812 acct-port 1813
radius-server key 7 0355481F031F761D
radius-server vsa send accounting
radius-server vsa send authentication
call application voice prepaid tftp://192.168.1.2/debitcard-multi-lang-Cisco.1.1.0.2.tcl
call application voice prepaid pin-len 10
call application voice prepaid warning-time 300
call application voice prepaid redirect-number 8662195822
call application voice prepaid language 1 en
call application voice prepaid language 2 sp
call application voice prepaid language 3 ch
call application voice prepaid set-location en 0 tftp://192.168.1.2/prompts/
call application voice prepaid set-location sp 0 tftp://192.168.1.2/prompts/
call application voice prepaid set-location ch 0 tftp://192.168.1.2/prompts/
gw-accounting aaa
==================================================
Getting session id for NET(00003600) : db=6418E654
AA/ACCT/NET(00003600): add, count 1
Getting session id for NET(00003601) : db=6410D098
AAA/ACCT/NET(00003601): add, count 1
AAA/ACCT/CONN(00003601): Pick method list 'h323'
AAA/ACCT/SETMLIST(00003601): Handle 94000002, mlist 62D3B124, Name h323
Getting session id for CONN(00003601) : db=6410D098
AAA/ACCT/CONN(00003601): Queueing record is START
AAA/ACCT(00003601): Accouting method=ClearBox (RADIUS)
AAA/ACCT/EVENT/(00003601): ATTR ADD
AAA/ACCT/CONN(00003601): START protocol reply PASS
AAA/ACCT/EVENT/(00003601): VOICE DOWN
AAA/ACCT/HC(00003601): Update VOICE/000020D3
AAA/ACCT/HC(00003601): VOICE/000020D3 [sess] (rx/tx) base 0/0 pre 0/0 call 0/0
AAA/ACCT/HC(00003601): VOICE/000020D3 [sess] (rx/tx) adjusted, pre 0/0 call 0/0
AAA/ACCT/CONN(00003601): Queueing record is STOP osr 1
AAA/ACCT(00003601): del node, session 174133
AAA/ACCT/CONN(00003601): free_rec, count 1
AAA/ACCT/CONN(00003601): Setting session id 174144 : db=6410D098
AAA/ACCT/HC(00003601): Update VOICE/000020D3
AAA/ACCT/HC(00003601): Deregister VOICE/000020D3
AAA/ACCT/EVENT/(00003601): CALL STOP
AAA/ACCT/CALL STOP(00003601): Sending stop requests
AAA/ACCT(00003601): Send all stops
AAA/ACCT/NET(00003601): STOP
AAA/ACCT/NET(00003601): Method list not found
AAA/ACCT/CONN(00003601): STOP protocol reply PASS
AAA/ACCT/CONN(00003601) Record not present

VSAs are collected by the RADIUS server during the accounting process when AAA is configured with the Debit Card feature. Data items are collected for each call leg created on the gateway. A call leg is the internal representation of a connection on the gateway. Each call made through the gateway consists of two call legs: incoming and outgoing. The call leg information emitted by the gateways can be correlated by the connection ID, which is the same for all call legs of a connection.
Use the H.323 VSA method of accounting when configuring the AAA application.
There are two modes:
â¢Overloaded Session-ID
Use the gw-accounting h323 syslog command to configure this mode.
â¢VSA
Use the gw-accounting h323 vsa command to configure this mode.

Faxing With A Calling Card

Similar Messages

Maybe you are looking for