Full screen playback on second monitor results in having to force quit Premier if a window opens on the second monitor.

Run into this problem a few times now. If I have full screen playback going to my second monitor, and then I try to do something like link media and the link media window opens on that second monitor I can't figure out a way to get to it. I end up having to force quit. Because the link media window causes all other application buttons to disable while it is open I have not been able to find a solution other than force quitting, reopen and disable full screen playback, open link media window and move it to the other monitor and then again enable full screen playback.
Has anyone run into this? Am I missing an easy solution?

You need to set up your Graphics Card Application first eg A and B Monitors , side by side etc.
In my case..a NVidea Display Application does this from the Control Panel
Then the second monitor will appear in display setting (Premiere).
My second monitor is entirely dedicated to full screen playback display.

Similar Messages

Popup window opens in the second page - plz help gurus.

Hi All,
I'm calling a transaction through ITS. There is a hyperlink in a report brings up PDF in the popup window. Popup window comes up in the second page of the report after closing in the first page of the report. Popup comes in all the consecutive pages of the report once I click on the hyperlink. This is really frustrating. Pls let me know if i need to do any configuration to avoid this problem.
Thanks,
Kumari

Hello Kumari,
are you using the SAP GUI for HTML (webgui)? Normally, no hyperlinks are used except on documents inside an HTMLviewer (like in TX TRIP), or when Drag & Relate is activated.
I suppose the link is part of a document that is shown in an HTMLviewer. Though this document does not belong to the ITS or the SAP GUI for HTML it uses ITS's URLs to address a new page or document. But, with this URL the status of the ITS or the application does not change, thus showing the popup over and over.
If you have a tool to trace the HTTP protocol you can check for the URLs that are send on a particular action. I
Best regards,
TJ

Dual Monitor and Full screen playback in Color 1.0

So, I was wondering if somebody could help me out.
I have 2 screens, one is a 23" ACD other is a 23" dell. I am going to be color correcting with my Matrox MXO setup on the 23"ACD. Whenever I do full screen playback the waveform monitor and vectroscope and all that jazz is not available anymore (obviously because of full screen)
So I was wondering what my options were:
1. Setup the waveform and vector scope to show on my primary display? (if possible, I'm not sure how to do it)
2. Do I have to get another graphics card and run three monitors?
3. If I Color grade with full screen playback disabled am I still utilizing the MXO for grading?
I am new to Color and how it works so I apologize if these questions seem "newbie-ish" of me.
Thanks

Isn't there a SINGLE MONITOR option in COLOR? Use that.
I don't think two graphics cards will work with Color, as Color relies on the card when it comes time to render. Might mess it up, or not work.
Shane

Full Screen Playback Control Impossible Using Monitor 2 in Dual Monitor

Recent iTunes update (patch didn't fix) causes playback control to disappear when the cursor is on the monitor showing the movie. Controls reappear when cursor is moved to first monitor. User cannot get the cursor near the control panel. Must drop out of full screen playback to touch controls with the cursor.

Isn't there a SINGLE MONITOR option in COLOR? Use that.
I don't think two graphics cards will work with Color, as Color relies on the card when it comes time to render. Might mess it up, or not work.
Shane

Full screen playback jittery with Aero enabled

Hello,
Currently running the CS5 trial on a new (built specifically for cs5) W7 64 based Dell 12-core Xeon box with three monitors attached via two Nvidia Quadro 3800 cards and am having issues with the full screen playback - namely, when my third monitor is enabled for full screen playback (connected via DVI>HDMI, 1920x1080@50Hz - yes I'm in PAL land) and my sequence matches, e.g. 50Hz - the playback is jittery (vsync slowing frame rate)- disabling Aero causes most of this to go away but now desktop video has to be disabled and there is some horizontal tearing (e.g. the vsync is now working but slightly adrift).
Googling around seems to indicate others with similar problems so this might be a W7 problem - has anybody else seen this kind of issue, and if so got a decent resolution?
I'd rather not have to splash out on unneccesary HDSDI and then HDSDI>HDMI I/O's when on paper a monitor connected via HDMI should playback correctly (which Windows Media Center does) - it also doesn't seem too much to ask for full screen playback to work 'out of the box', does it? How else are we expected to do this otherwise?
I've filed a bug report on this but any other ideas or suggestions appreciated.
Thanks
Sacha Goodwin

1. OK - From W7 Performance Info:
More details about my computer
Component
Details
Subscore
Base score
Processor
Intel(R) Xeon(R) CPU X5670 @ 2.93GHz
7.8
5.9
Determined by lowest subscore
Memory (RAM)
12.0 GB
7.8
Graphics
NVIDIA Quadro FX 3800
6.9
Gaming graphics
4607 MB Total available graphics memory
6.9
Primary hard disk
288GB Free (465GB Total)
5.9
Windows 7 Enterprise
System
Manufacturer
Dell Inc.
Model
Precision WorkStation T7500
Total amount of system memory
12.0 GB RAM
System type
64-bit operating system
Number of processor cores
12
Storage
Total size of hard disk(s)
465 GB
Disk partition (C:)
288 GB Free (465 GB Total)
Media drive (D:)
CD/DVD
Disk partition (F:)
0 B Free (39 MB Total)
Graphics
Display adapter type
NVIDIA Quadro FX 3800
Total available graphics memory
4607 MB
      Dedicated graphics memory
1024 MB
      Dedicated system memory
0 MB
      Shared system memory
3583 MB
Display adapter driver version
8.17.11.9790
Primary monitor resolution
1920x1200
Secondary monitor resolution
1920x1200
Secondary monitor resolution
1920x1080
DirectX version
DirectX 10
Network
Network Adapter
Intel(R) PRO/1000 MT Server Adapter
Notes
The gaming graphics score is based on the primary graphics adapter. If this system has linked or multiple graphics adapters, some software applications may see additional performance benefits.
Disk system doesn't apply in this case as we use an Editshare NAS.
2. First thing I did was a clean install of W7 (Enterprise), I always start from vanilla install.
I'm a bit unsure about your tuning guide - can you document what improvements you get after changing said settings? I note the option "Adjust Visual Effects and check Adjust For Best Performance" is one way to turn off Aero (which I've tried anyway), which whilst sort of resolving the original problem, unfortunately now causes other display issues (and also caused CS5 to crash when using the source trimmer window) so have had to switch it back.
Turning off the services as you are suggesting seems a bit drastic just to get a plain DV clip without any FX to playback smoothly (e.g. CPU util is about 3% in these situations, network at about 5%, disk not doing anything).. it's the kind of thing I would have done about 10 years ago but modern machines are supposedly built around HD multimedia so it seems odd to still be expected to do this kind of thing now.
FYI, this was the thread that suggested turning off Aero to fix:
http://social.technet.microsoft.com/Forums/en/w7itproperf/thread/d4f155d8-6ff6-4741-bb2d-8 ed184b7a45c
Out of interest, what do other people use to get full HD preview under CS5? Is it all OK out there in NTSC land @ 60fps?
Thanks
Sacha.

Full screen Playback only on Main Display

I noticed that after upgrading to Lion quicktime player won't play movies full screen on my second display. Under Snow Leopard if the quicktime window was on the second display and you hit full screen it would fill the display is was on. Now the video slides to the main display and then goes full screen. There doesn't seem to be any way to change that behavior. There are no preferences.
The only work around is to move the menu bar in the display preferences to the second menu, so that the second monitor becomes the main one.
Any solutions or terminal commands I make to set it back to the old way?

This issue seems to be related to Lion's "Full Screen App" mode in Lion, where a window that goes to full screen creates a separate Space, and it always uses the "primary" screen (the one with Menu Bar). So it's the same as making a Safari window go to full screen; it always uses the screen with the Menu Bar.
But I did noticed something interesting. If it's a video that can play in iTunes (instead of using QuickTime Player), then you can make it play full screen on the other screen. Play the video in iTunes so that it plays in a separate window. Move the window to the secondary screen (the one without Menu Bar), and make it go full screen. It plays at full screen on that screen.
So it is possible, but Apple has not done it for QuickTime Player. You should send Apple feedback to request the same functionality for QuickTime Player, like I did.
Also, VLC Player (third-party video player app) still uses the "old school" way of doing full screen mode, so it still works the same way as before. Full screen will go to the screen that has the window playing the video.

Full screen playback as with 2nd screen blacked?

I've got two Apple displays hooked up to my G5, and unlike DVD Player, which automatically blacks the second screen when I enter full screen playback, Quicktime leaves the second screen unblacked- I'm hoping I can figure out a way to get Quicktime to black the second screen as with DVD Player? As opposed to simply dimming it (since the syst. prefs don't allow for complete dim-to-black) Any other users notice this as an issue? Obviously not a soul-crushing problem, but is kinda annoying...
Searched for previous posts on this topic, didn't see it posted already, which surprised me. But I don't see any settings in the Quicktime full screen playback settings that might address this.
cheers,
Jack

Holy blackout, Batman! That did the trick- my "Full Screen" options were set to "Fit to Screen" instead of "Fill Screen", and I checked the "Background Color- show on all displays" box. Nice. Thanks much!!!

Toggling for Full Screen playback

I am having no success toggling to full screen playback in Premier Pro CS6 using ctrl+` or anything else. The onmly way I can get to full screen during playback is by going to Edit/Prefernces/Playback and ticking one of the 2 monitors (or both) that I have connected. The only way of going back to small screen playback is by going into the same menu and deselecting.
Look forward to hearing from anyone,
Dan

This isn't the answer you are looking for, but maybe I can help a little.
If you look in the keyboard shortcuts and search for "playback" the one under "edit" will at least allow you to call up the window faster than using menus. I assigned Ctrl-Shift-P because I don't care about setting poster frames and I can remember the "P" for "playback".
I don't see any way to select or deselect the monitor via the keyboard. At least not from within Premiere Pro. If you were a moderately talented programmer, there are ways to control Premiere Pro from outside of the program itself. I used to write programs to control other programs but I haven't done so since about 1994.
Perhaps submitting a feature request would be appropriate. https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform

Full screen playback in PE9 garbled - anyone else see this?

I mentioned this in a general post but I'll make it a specific question now -
When I click on the "full screen" button near the top right of the interface, full screen playback has a corrupted area which corresponds with where the timescale is on the normal interface. Sometimes the playback cursor "breaks through" as a black vertical line too.
Does anyone else see this?
I have the latest Nvidia drivers installed. Windows XP Pro SP3 Q9300 quad core PC 2GB memory.
Thanks for any observations.

It's very obvious if you do have the problem - a wide strip of the video (horizontal, matching the timescale hidden beneath the full screen display) gets shifted sideways somewhat (flickering on and off), so that any vertical object in the footage gets displaced sideways at that point in an obvious juddering fashion. I tried to do a screen grab but simply doing that makes the problem change - it is more evident when the footage is running than when frozen.
Anyway, adjusting the Windows Display Properties "hardware acceleration" slider, moving it to the left till it is set to the point where the message beneath reads "Disable all DirectDraw and Direct3D acceleraions. Use this setting to correct severe problems with DirectX accelerated applications" seems to fix the problem.
Graphics card is a GeForce 8600 GT, in case that's relevant.
At least I know how to work around the problem. Let's see if others come across the same problem in due course. Maybe it's just a local issue.

No Full Screen Playback

I am trying to view full screen playback but I am not seeing any AV devices under the video playback menu. When I go to view/Video Playback the only option is "None".
I have ben able to get full screen playback with this setup as recently as today but something has changed.
I tried a complete reinstall and that did nothing.
I have tried refreshing A/V devices but it doesn't detect anything, not even the laptop screen.
Any ideas?
Message was edited by: jonmeredith

Using FCP 7.
I have gotten it to work a couple of times, but I am never sure what is fixing it. Restarting multiple times mixed with something else seems to do it, but then if I restart one more time after that I lose it again - the External A/V window comes up upon launching the program saying that it was unable to locate the Digital Cinema Desktop Preview.

I have two screen on my PC. Adobe always opens on the second screen. I would like to change this. Ho

I have two screens on my PC Adobe always opens on the second screen. How do I change this to open on the first screen.

It should (should) stay where you close it from, especially if you have it maximized on that monitor. I can't guarantee that because I'm having the same problem with Firefox this morning. I always open it on my secondary montior, and today it will only open on the primary.

Black screen windows 10 at the second turn

Hello
I have a strange problem after installing Windows 10 at the second turn on the computer black screen with no cursor display on the computer is not responding as they walk fans can be heard when the black screen that the Windows logo is so fuzzy and these dots also tried to install Windows 10 but the same even downloaded files I looked at the other monitor also does not work and yet how is this black screen that you can turn off the computer by disconnecting the power supply and turn again how it works but for re-inclusion happens as I described, please help there is no record of a drivers like what all I

I should mention I installed Windows in gpt/uefi.
Therefor I believe the CSM reveals both the Intel HD4000 and the GT650M.
Both show up in the devicemanagement tool of Windows.
Maybe I have to disable the Intel GPU somehow?

I have two monitors on my Mac. Running FF3.6.16 new windows now want to open on the wrong monitor. How do I get FF to open on the main display?

I have an eMac with a second display. I am running OS X 10.4.11 (Tiger) and Firefox 3.6.16. Everything was working fine until the other day I opened a second window in Firefox and dragged it to my secnd monitor. I later closed it. Since then all New Window requests, including when starting Firefox always open on the second monitor. How do I tell Firefox I want my main monitor has the primary monitor?

It has nothing to do with the Mac, but more with the software exporting the displays on the PC. A typical VNC server will generally only export the primary monitor.
What PC software are you using to export the display(s), and what Mac software are you using to view the PC displays? That may help someone come up with a workable solution for you (or not ).

How do I get firefox 4 on Windows 7 to 'remember' to open on monitor 2? It keeps opening on the main monitor, only.

When you open a program in a multi-monitor set-up and transfer the program to the second monitor and close it, when it next opens it should open on the second monitor. Firefox 3.x performed this way. Firefox 4 does not -- it only opens on the main monitors, always.
Please build this into the product or provide an option for it?
Thanks,

Update: I forgot something about the way BootCamp installs Windows...
I had temporarily turned off BlueTooth on OS X because I didn't need it, and when you do that, it effectively removes it from the system's list of devices.
So I just wiped the Windows partition, turned BT back on in OS X, and re-installed Windows. Just to make sure, I went through and manually installed all the drivers by hand and then let the BootCamp utility install them as well, and it's been working like a charm!

I have continuous problems with my iPad Mini, and it is getting worse! Newstand application keep pausing or crashing, websites keep hanging first time in but then open fine the second time, and I have problems with applictions crashing.

I have continuous problems with my iPad Mini, and it is getting worse! Newstand application keep pausing or crashing, websites keep hanging first time in but then open fine the second time, and I have problems with applictions crashing. Has anyone experienced similar problems and any suggestions?

Has the device always behaved this way? Did this start as a result of an update to the iOS software? If the problem is that bad, you should probably restore the iOS software and then restore from a backup. If that fails, restore as new and rebuild the device. If that fails, it's time for a trip to an Apple Store to let them have a look at the iPad.
Use iTunes to restore your iOS device to factory settings

Full screen playback on second monitor results in having to force quit Premier if a window opens on the second monitor.

Similar Messages

Maybe you are looking for