GD80 Status LED and System Suspend problem

Hi everyone.
My hardware:
- MSI P55-GD80
-BIOS AMI v1.4
-Intel Core i7 860
-OCZ 4GB (2x2GB) 1600MHz CL8 Gold Low-Voltage
-Zotac GeForce GTX 275 896MB
- PSU: Corsair TX850W
-HDD : 1- Seagate Barracuda 7200.12 250GB (ST3250318AS); 2 - Seagate Barracuda 7200.10 500GB (ST3500630AS); 3 - Samsung Spinpoint F3 1TB (HD103SJ)
- Debian GNU/Linux "Squeeze", kernel 2.6.32, amd64
I have a problem with LEDs on motherboard. when they are lighting I can't "wake up" pc from S3 state (aka suspend). It just restarts when wake up event appears.
Actually the lighting LEDs are: 1&2 VTT_PHASE; "LED2" , which indicates active PCI-Express 16x port; CPU Phase LED panel (it shows 8) and + - buttons used for overclocking (OC Gene and these buttons are turned off in BIOS)
But the strangest thing is that the LEDs sometimes turns on and off (actually one day they do, in other they don't) when I turn on computer, even when they are disabled in BIOS (Green Power => Motherboard LED Control) [btw. Touch Panel is disabled and it still works ]
I have cleared CMOS , swapped SATA cables and I have checked RAM and PCI-Express connection (sometimes when I reinsert graphic card everything starts to work well, but for a few days the problem appears again. The same goes to SATA cable )
Anyway it looks to me like an error reporting (or something) but there is nothing about that in the manual. (or it's a BIOS bug).
I have been searching about it, but i haven't found anything.
Anyone had this kind of problem?
EDIT: BIOS upgrade from 1.4 to 1.5 didn't help.

Hi ctemp1,
Alert: sc0 Config Reader (Sun Fire High-End
Systems) A Status Domain A - Domain Status is: In
Recovery
But the domain has not been restart.
$ uptime
12:28pm up 52 day(s), 2:41, 6 users, load
average: 2.35, 2.49, 2.66SunMC is forwarding the status detected by your SMS daemons: so uptime probably isn't showing the whole story. Try a SMS command like "showenvironment -d A" and see what's reported.
Also what version of SMS are you running? SunMC has an update available for the new SC hardware, USIV uniboards, and newer versions of SMS that change the SunMC addon from the name "12k-15k" to "High-end Systems":
http://www.sun.com/download/products.xml?id=431df39d
If it looks like there's a mismatch between what SunMC and SMS are reporting, and you're running a newer version of SMS (i.e. 1.5) then you should give that update a try.
Regards,
[email protected]
http://www.HalcyonInc.com

Similar Messages

KT6V a)LAN LED and b)vga problem

Hi everybody,
Recently a friend of mine bought a KT6V-LSR, there are two things going on firstly, the led of activity on the LAN jack at the rear panel (backbone) doesn’t flash at all, it stays always on, other pc on the same switch with an MSI motherboard doesn’t have a problem (the led flashes during activity). Does anybody have the same motherboard and have checked that led?
Secondly a problem mentioned by an other person here in this forum, the screen turns to black for 1-2 seconds in windows without a specific reason the VGA is a Gigabyte nvidia 5200 128MB, the problem most of the times appears during overlay, powerdvd and windvd, but also in windows while surfing, the PSU is fine it used to work with a ATI-9800Pro. Does anybody have the same problem?
Thanks for the help!

i´m having the same problem as you
In the lan case it works perfect but the led don´t flash .this is not a big deal but the other one aparently to be a problem beetwen video and motherboad (AGP, bios or driver nvidia in my case)
becouse if you see (I have win xp installed SP1) check in panel control, admistrative tools icon, and go for succes visor , select system and look for an error with the following description
" a device has enter in an infinite loop and windows could estabilizase the system please save your work a reboot"
i still don´t know what to do first i´m thinking in flash the bios
My system configuration:
XP 2600 FSB166 Cache 512MB
MSI KT6V LSR Bios version:
MEM 512MB Kingston DDR400 CL3
VGA Biostar GF4MX440 64MB DDR AGP8x
Miro DC10plus Version 8.0
Power Supply 400W Sunshine
Encore Modem 56kbps chips ambient (Intel)
40gb 7200RPM MAXTOR
80GB 7200RPM Western Digital
Please help us!!!!! Thanks

4 Green LEDs and System Hang!!

I have the MSI K7t Pro 2-a, 512 of pc133 ram, geforce 2 mx, soundblaster live *which i have taken out* western digital hard drive 7200 rpm
I just now got this problem and it start when my brother was using it to play americas army. He was just sitting there waiting and the screen went black but the computer was still on.
Now when I reboot, i get 4 green leds and the computer will make it to the loading screen for win2k and soon as it gets to bout loading windows the screen hits black and the computer light is green and the work light, the little orange one is constant, it doesnt flash.
Whats the deal!
my sound card dont like this motherboard, ive had ram in this thing that it didnt like now this!! IS this MOBO PIECE OR WHAT!>
Thanks,

You are probably loading something the videocard doesn't like. Try to load windows in safemode. Keep hitting F8 during start up and you'll get a menu which has "start up in safemode" option. If you can get windows to start, everything looks terrible (256 colors, 480x640 etc). Reinstall the video drivers.
Is your board a 6330 or 6380?

APC UPS, Mountain Lion, and system restart problem

I have a Mac Pro (3,1) and it's been running Lion (10.7.x) for a long time. It's connected to an APC UPS XS 1500 via a USB cable for years. I've never had any problems with it.
Two weeks ago I updated to Mountain Lion (10.8.2). Since then I've returned to my machine to find that it had rebooted itself. After logging in, the system tells me that there was a problem and asks if I want to send the error report to Apple.
Yesterday, I tried unplugging the Mac Pro from the UPS, plugging it directly into a wall outlet, and disconnecting the USB-UPS cable. So far, I've had no problem with system restarts.
Has anyone had a similar problem? If so, did you solve it? How?
Thank you.

Hi, macjack. Thanks for your response.
So far, with the MP plugged directly into a wall outlet I've had no system initiated reboots or shut-downs.
I looked in the console log and there's so much stuff in there, I'm simply lost. Are there one or two keywords I should search for that might help in debugging the problem?
Again, thanks.

CS3 and system reinstall problem

I have had to reinstall the system on my MacPro. Reinstalled from the disc and then updated to 10.5.6 using the combo updater and everything seems to be working again.
I understand when you do a system reinstall that it doesn't touch any 3rd party applications.
I opened Photoshop and discovered that no matter what I type (font or size), it is pixilated and all jagged.
The other Adobe programs I have don't have this problem.
What am I missing to cause this problem? Any ideas?
Vicki

I would start by trying a New User (on the theory only Ps is hosing that font).
http://www.gballard.net/macrant/osx_troubleshooting.html
If the problem clears here, go back to you normal account and delete your Ps user preferences.
Also Font Agent Pro has a free demo you can download and check your fonts.
http://www.insidersoftware.com/FA_pro4_details.php
Also check out Insider Software SMASHER
http://www.insidersoftware.com/SM.php
Smasher
Flatten Mac OS X font problems fast
Smasher gives you the power to look deep inside your fonts and suitcases to solve problems fast. Using Smasher, you can:
Stop garbled text display
Prevent output problems
Clear pesky font caches
Verify font outlines
Perform suitcase surgery
Check font properties and permissions

Airport Utility and System Keychain Problem

I'm having a strange issue when trying to access Airport Utility on our imac. When I click on manual update I get a popup box asking for the administrator user name and pass word because Mac OS X wants to use System keychain. When I type those in the boxes and click allow an error message appears saying I typed an invalid password. I've rebooted, I booted up in Safe Mode which asks you for a password before it logs in - no problems there. I didn't try to access AU from there, not sure if that's possible. I've even gone to account settings and changed the password which requires you to enter the current password, that worked. I used the new password with that warning from Airport Utility but got the same error. I went back and changed the password back to the original and tried again, same error.
I don't normally access AU on that computer, I use my laptop and there are no problems there, so I don't know if this is a problem that just cropped up under SL or not. So far that's the only instance of this popping up with that issue. I don't believe I've ever seen it say it needed to access the System keychain before. Another oddity to this is I can open up Keychain Access and click on unlock the System keychain which then asks you for an administrator password, I enter it and it unlocks with no issue. Any help with this would be greatly appreciated.
John

Sometimes the Keychain just gets a bit "wonky." The simplest resolve, in most cases, is to delete all entries with the Kind of "AirPort base station password" and "AirPort network password" in the Keychain using the Keychain Access utility.

Cd's and system discs problems with new apple quick silver g4

hello hopefully someone can help me I just purchased this macine on ebay 2 weeks ago. The problem I am having is for one I cannot open the cd-r-rw without using popcorn to open it. When I try to insert a disc for an application or the system disks that he included with the purchase I cannot read any of them in fact as soon as i close the drawer with the disc in it it reopens in a few minutes. I can't even find a way to open the drawer with out popcorn there is no external place to open this up like my old cd rom had. I had a power mac beige g3. So in order to load anything I have to download the disk to a usb small portable plug memory card, plug it in to the new machines usb port and then download the program through there. So what do I need to be able to put a system disk or program disc into this machine and also able to open the tray I have now. Do I need something like a external cd-rom drive that hooks up into my usb port to be able to use the discs or what.
The one thing it does do is play a music disc if you openned it with popcorn and close it it plays the music disc but not the other type thanks Tim L

There are several things you can check or test. Follow these 3 rules and you'll be able to change drives in any Mac.
1. After changing Hard Drives ... are you restarting AND zapping PRAM or just restarting? Any changes to hardware configuration require zapping the PRAM (hold down command, option, p and r keys while restarting).
2. Making a copy of a startup disk onto a second Hard Drive is never as good as installing the OS independently on each drive. Even if they're both in the same computer. Be sure your new optical drive is in place and connected when installing OS.
3. Hard drives and optical drives have configuration addresses or designations. The ATA bus in Macs support 2 devices on each channel (2 channels). The optical drives are normally connected to the slower ATA/66 bus and are designated Master and Slave. If both drives are set as Master a conflict will occur. Check the jumpers located at the rear of the drive where the ribbon cable connects. There's usually a sticker on the drive which shows how to set them for the appropriate configuration.
Hope this helps ....
Gary

SUN Fire V65 - System Status LED - non-critical condition

Hi guys
We have a Checkpoint Cluster which is made up of 2 Sun Fire V65 servers.
The front panel of the servers are showing the System Status LED lights as Blinking Amber , which sun documenation has listed as
"Blinking amber: Indicates the system is in a non-critical condition" ref: http://dlc.sun.com/pdf/817-2024-12/817-2024-12.pdf
We have resetead the hardware, cleared ,logs, even change HW etc. The light goes away for some time and then returns.
Can anyone advise on what to do?
Sun has the following listed in their Troubleshooting pdf i ref before
"Non-Critical Condition
A non-critical condition is indicated with a blinking amber status LED and signifies
that at least one of the following conditions is present:
¡ Temperature, voltage, or fan non-critical threshold crossing.
¡ Chassis intrusion.
¡ Satellite controller sends a non-critical state, via the Set Fault Indication
command, to the BMC.
¡ A Set Fault Indication command from the system BIOS. The BIOS may use the Set
Fault Indication command to indicate additional, non-critical status such as
system memory or CPU configuration changes"
Is there any Unix / Linux / SPLAT logs I can look at or debugging we can look at.
Thanks in advance

Your initial description mentions that you have swapped various pieces of hardware around. I presume that means you used current parts instead of new-never-used components. Are both of the clustered systems showing the same symptoms?
I can only think of a couple of additional things to try.
Firstly, those are old boxes. V65's went EOL in January 2005, so yours are at least that old if not older. They are x86 architecture. Have you replaced the CR2032 CMOS battery that's on the systemboard? Have you additionally checked for voltage fluctuations in the data center? A marginal power supply can "mostly work" but it can be effected by an AC mains issue.
If that doesn't change anything, then you may need to contact Checkpoint. They may be able to point you toward some sort of heartbeat function that is tripping a fault level when it flip-flops between the two systems.
That's a software investigation and would be outside the scope of this forum.

"waiting" and "system error" status cannot be resent in rwb?

Hi,gurus:
In RWB->MESSAGE MONITORING,I can't resend or cancel the messages with the status " waiting" and "system error".
when I clicked "resend" button,it asked for user and password.After I was authentificated,the system didn't resend a message. Have you ever met this issue?
By the way,I could resend the error messages before.
Thanks in advance.

Hi,
I checked the note 1233918,and it talked about the same issue.
But the solution is as follows,which I don't know what to do.(Our PI version is PI7.0 SR3 SP14)
Symptom
When the first message for a managed system is cancelled or resent, after pressing ok in the logon pop-up nothing happens - message is not resent or cancelled. The logon data is correct, since subsequent resend/ cancel works without further logon request. Another symptom is cancelling or resending a wrong message, when using the filter mechanism in the table. E.g. the table displays messages A, B, C, D. If message C is selected and after that the filter is set so that message C is hidden from the filter selection, when selecting message D and trying to resend/cancel it, message C is cancelled/resent (the hidden one, previously selected) and nothing is happening with message D.
Other terms
NWA, PI, Message monitoring, resend, cancel
Reason and Prerequisites
The UI Proxy connection was not obtained properly. Another reason - TableAccessories was not invalidating the nodes properly. Also after filtering the result list, resend/cancel was taking wrong message Ids.
Solution
For SP5 install LMNWABASICCOMP05P_1.SCA or higher patch level.
For SP6 install LMNWABASICCOMP06P_1.SCA or higher patch level.

MDS 9216 - showing red status LED, not starting up

Hi,
In a recent power loss (took out our R&D UPS in the process), an MDS 9216 we have in R&D failed.
On power up, it shows a red status LED, and does nothing. We've pulled and swapped PSUs (something we're told is a common fix for a common problem with these chassis), to no avail.
Strangely, we pulled the fan card (which had a green light), and put it back in to see it now also has a red status light.
We've swapped all cards around for new and spares (even the main cards) and they show up with red status lights in the chassis (can't test them in another chassis at present) so I assume this problem is with the chassis itself (ie the backplane or PSUs).
Any ideas, any similar experiences?
Many thanks,

As far as warranty, it would be covered for 1 year or 90 days from purchase....not sure which, but since the 9216 is end of sale for a few years now, I doubt that is covered under warranty. If you have a maintenance contract covering that 9216 serial number, then it would be covered. The design on the 9216 is that the module 1 is not field replaceable. There is no Cisco part number for the slot1 line card. It is a hybrid of a 16 port FC module with a supervisor daughter card. It is basically considered part of the chassis. If you have your own spare 9216 and feel energetic you could replace the slot 1 line card....but from the official support perspective, it is not replaceable.
There are no other replaceable parts besides the chassis and PS that would cause this problem. (I assume you have removed any line card from slot2 to be sure it was not causing the problem).
Thanks,
Mike

1131AG no status LED

Hello,
One of my 1131AG access points stopped working and I am trying to troubleshoot.
When I apply power (originally it was PoE) the Status LED never does anything (not even a blip), the Ethernet and Radio leds will flash, but the status LED will never light.
Any thoughts?
Thanks
Rob

Rob,
     Is this an IOS or LWAPP access point your troubleshooting, the reason I ask is because it's possible to disable that Circular status LED from within the software and it's possible it has gotten disabled.
     If it is an LWAPP access point, I'd just do a factory reset on the unit and then see if it comes back up or console into it first and see if it is even booting.
     if it is an IOS access point console into the unit and enter enable mode by typing en; then enter config mode (conf t), from there you should have an command that is something like status led and the options are enable, disable, blink
Hope this helps... Please rate useful posts.
Thanks,

Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

hi,
I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives Ethernet LED = Off; Radio LED = RED ; Status LED = RED and only next listing in the screen:
Xmodem file system is available.
Flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error during initializion of the flash filesystem.
The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
ether_init
tftp_init
boot
When I type this commands, it doesn't help at all. The output will be following:
ap: flash_init
Initializing Flash...
flashfs[0]: out of memory
...done Initializing Flash.
ap: ether_init
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ap: tftp_init
Unable to get our ip address: no "IP_ADDR" variable set
ap: boot
Loading ""...; permission denied
Error loading ""
Interrupt within 5 seconds to abort boot process.
Boot process failed...
ap:
what i do ? please help , thanks

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red

D400 - system status LED blinking, network LED blinking

Hi - Just recently started experiencing this problem with my D400.
The system status LED is blinking, which according to the user guide means that WHS is either booting or shutting down. The Network LED shows activity.
Problem is that I can't get on the D400 via remote desktop.
Frustrating. Talked with support already, said only option is to send in to depot or find a local resource to troubleshoot or fix. Problem is that we have our music/photos on this thing.
Support also said that if we factory reset data on all drives will be erased.
Looking for help wherever I can get it. Thanks!
Scott

Hi scottdcm, and welcome to the Lenovo User Community!
To get your music/photos off the system before returning it for service, connect the hard drive(s) to another computer with a SATA connection. An external USB/SATA connector or drive enclosure will also do the job.
You can also remove any drives you have added before shipping it for service.
Hope this helps!
I don't work for Lenovo. I'm a crazy volunteer!

I have a mid 2009 13'' MBP. I got the battery replaced in Apple store, It then stopped displaying the battery status LED. After some months of use my MBP died. I got it checked in Apple verfied Service centre and was told that logic board was to blame

I have a mid 2009 13'' MBP. I got the battery replaced in Apple store, It then stopped displaying the battery status LED.
After some months of use my MBP died outside USA. I got it checked in Apple verfied Service centre and was told that logic board was faulty.
After I came back to US I took my MBP to Apple store and was told that there is liquid damage in the system. My question is that if there was liquid damage why did my MBP stop displaying the battery status right after the battery was changed secondly why didnt the apple verified Service centre tell me that there was liquid damage afterall I paid them the money for diagnosing the problem.
Is there a process i can followup on this problem

These are question you would need to ask that service center.
This is a User to User forum. No Apple employees here.

Cisco 1131AG LWAP status led yellow and other leds blinking green

I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.
The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).
The SSID broadcast is enabled.
On the switch the interface is up and there is traffic going in and out of the LAP.
I tired power reset and factory reset for the APs but the problem remains the same.
Any ideas for what might be the problem ?!!
Regards

Yes the clients are not able to see the SSID broadcasted by the AP.
But these APs were functioning normally before without any changes to the WLC config.
I had the same problem with other APs but they went back to normal state after a hardware reset to the APs.

GD80 Status LED and System Suspend problem

Similar Messages

Maybe you are looking for