Grandstream GXW4108/Elastix setup , Caller ID problem

First I have to say, I don't know this gateway. But I have seen this before with Linksys gateways where you get the device account ID instead of who called. In asterisk terms you are seeing the called ID and not the caller ID. 
Are you sure you have subscribed to the caller ID service from your PSTN carrier? If you do, then the setting you must change is in the voip gateway and not in asterisk. You can use the called id to direct the inbound call via an inbound route to an extension, ring group, queue, or IVR.

Hello everyone I am new to Elastix and VOIP.
I just setup GXW4108 and Elastix. Everything is Ok.But Incoming call show Wrong Caller ID(User ID from elastix trunk).I want to see correct Caller ID.Help!!!!!!!!!!!!
This topic first appeared in the Spiceworks Community

Similar Messages

  • Cannot setup caller id because I cannot receive th...

    cannot setup caller id because I cannot receive the verification code.
    I see a lot of people ask the same question. anyone knwo the solution?

    same problem.  Someone for god sake please reply

  • Cannot setup Caller ID

    I am a "fellow member" and my administrator purchased a subscription for me to make calls.  When I login to my account, there isn't a "setup caller identification" tab anywhere.  I understand the process (verify number by 2 text msgs) but I can't find it anywhere.
    The only thing that has "verify number" is under the voicemail tab.

    Hi,
    Do not use the Skype app to do this.  Go to Skype.com from a browser and click the sign in button at the to left hand side of the page.  Then sign in with your SkypeId and password. You will then see information about your account.  Click on the 'call phones' tab and under your recent call stats there will be a Caller ID setting link.  This is where youscan set the caller ID.
    If there is anything else or if you have any problems please feel free to get in touch.
    Good luck.
    Feel free to contact us on Skype ID: tetra4comms
    or type 'Tetra4 Skype' in your search engine.
    Tetra4 - Putting Skype to Work.
    www.tetra4.com

  • Exchange 2013 cu3 setup fails with 'problem... validating the state of Active Directory... supplied credential... invalid'

    Windows Server 2013; Exchange Server 2013 with Cumulative Update 1
    Cannot install Cumulative Update 3 for Exchange Server 2013. It fails with
    [xxx] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Active Directory operation failed on . The supplied credential for 'XXX\Xxx' is invalid.  See the Exchange setup log for more information on this error.
    [xxx] [0] [ERROR] Active Directory operation failed on . The supplied credential for 'XXX\Xxx' is invalid.
    [xxx] [0] [ERROR] The supplied credential is invalid.
    (Crosses - XXX - replace original values.)
    I have found that a few others have experienced the same problem but found no solution, nor could come up with anything myself. If it is any hint, Event 40961 was logged in the Event Viewer around the same time on almost all installation attempts to be purely
    conincidental:
    The Security System could not establish a secured connection with the server
    ldap/xxx.xxx/[email protected] No authentication protocol was available.
    Both Windows Server and Exchange Server otherwise work OK, and do not recall any issues with Cumlative Update 1 installation.

    Hi vhr1,
    Based on my knowledge, the Event ID 40961 is a warning message.
    This behavior occurs when we restart the server that was promoted to a DC. The Windows Time service tries to authenticate before Directory Services has started.
    Found some resources for your reference even if the Exchange Version is mismatched:
    http://blogs.technet.com/b/jhoward/archive/2005/04/20/403946.aspx
    http://support.microsoft.com/kb/823712/en-us
    About the error message, "Setup encountered a problem while validating the state of Active Directory: Active Directory operation failed on . The supplied credential for 'XXX\Xxx' is invalid."
    The error message InvalidCredentials means: the wrong password was supplied or the SASL credentials cannot be processed.
    Found a similar thread for your reference, hope it is helpful:
    http://social.technet.microsoft.com/Forums/en-US/98e26ad6-8e43-4ef5-8ff9-e9fee6e76bda/bind-operation-is-invalid?forum=exchangesvrdeploylegacy
    Feel free to contact me if there is any problem.
    Thanks
    Mavis
    Mavis Huang
    TechNet Community Support

  • Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site

    Have an existing ex2010 sp3 organization.
    Could not run ex2013cu1 setup from my newly built 2012 server, getting the error in the subject line.  I used the command line to run the AD preparation steps successfully from my 2012 DC/GC, then tried to run setup again from the new 2012 server and
    still get the same error.  The error itself in the log is pretty useless:
    [05/07/2013 01:19:13.0137] [0] **********************************************
    [05/07/2013 01:19:13.0137] [0] Starting Microsoft Exchange Server 2013 Cumulative Update 1 Setup
    [05/07/2013 01:19:13.0137] [0] **********************************************
    [05/07/2013 01:19:13.0152] [0] Local time zone: (UTC-08:00) Pacific Time (US & Canada).
    [05/07/2013 01:19:13.0152] [0] Operating system version: Microsoft Windows NT 6.2.9200.0.
    [05/07/2013 01:19:13.0152] [0] Setup version: 15.0.620.29.
    [05/07/2013 01:19:13.0152] [0] Logged on user: DOMAIN\ADMINISTRATOR.
    [05/07/2013 01:19:13.0168] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
    [05/07/2013 01:19:13.0168] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
    [05/07/2013 01:19:13.0215] [0] Command Line Parameter Name='sourcedir', Value='\\h1\f$\junk\installers\server\Exchange\2013cu1'.
    [05/07/2013 01:19:13.0215] [0] Command Line Parameter Name='mode', Value='Install'.
    [05/07/2013 01:19:13.0215] [0] RuntimeAssembly was started with the following command: '/sourcedir:\\SERVER\f$\junk\installers\server\Exchange\2013cu1 /mode:Install'.
    [05/07/2013 01:19:13.0215] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
    [05/07/2013 01:19:13.0793] [0] Finished loading screen CheckForUpdatesPage.
    [05/07/2013 01:19:38.0762] [0] Finished loading screen UpdatesDownloadsPage.
    [05/07/2013 01:19:40.0496] [0] Starting file's copying...
    [05/07/2013 01:19:40.0496] [0] Setup copy files from '\\SERVER\f$\junk\installers\server\Exchange\2013cu1\Setup\ServerRoles\Common' to 'C:\Windows\Temp\ExchangeSetup'
    [05/07/2013 01:19:40.0700] [0] Finished loading screen CopyFilesPage.
    [05/07/2013 01:19:40.0840] [0] Disk space required: 1292445007 bytes.
    [05/07/2013 01:19:40.0840] [0] Disk space available: 23767240704 bytes.
    [05/07/2013 01:19:59.0762] [0] File's copying finished.
    [05/07/2013 01:19:59.0965] [0] Finished loading screen InitializingSetupPage.
    [05/07/2013 01:20:02.0934] [0] Setup is choosing the domain controller to use
    [05/07/2013 01:20:09.0325] [0] Setup is choosing a local domain controller...
    [05/07/2013 01:20:11.0794] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency. 
    See the Exchange setup log for more information on this error.
    [05/07/2013 01:20:11.0794] [0] [ERROR] Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.
    [05/07/2013 01:20:11.0809] [0] Setup will use the domain controller ''.
    [05/07/2013 01:20:11.0809] [0] Setup will use the global catalog ''.
    [05/07/2013 01:20:11.0825] [0] Exchange configuration container for the organization is 'CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain,DC=local'.
    [05/07/2013 01:20:11.0919] [0] Exchange organization container for the organization is 'CN=DOMAIN,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain,DC=local'.
    [05/07/2013 01:20:11.0966] [0] Setup will search for an Exchange Server object for the local machine with name 'WEX1'.
    [05/07/2013 01:20:12.0028] [0] No Exchange Server with identity 'WEX1' was found.
    [05/07/2013 01:20:12.0044] [0] The following roles have been unpacked:
    [05/07/2013 01:20:12.0044] [0] The following datacenter roles are unpacked:
    [05/07/2013 01:20:12.0044] [0] The following roles are installed:
    [05/07/2013 01:20:12.0059] [0] The local server does not have any Exchange files installed.
    [05/07/2013 01:20:12.0075] [0] Server Name=WEX1
    [05/07/2013 01:20:12.0137] [0] Setup will use the path '\\SERVER\f$\junk\installers\server\Exchange\2013cu1' for installing Exchange.
    [05/07/2013 01:20:12.0137] [0] The installation mode is set to: 'Install'.
    [05/07/2013 01:20:27.0591] [0] An Exchange organization with name 'DOMAIN' was found in this forest.
    [05/07/2013 01:20:27.0591] [0] Active Directory Initialization status : 'False'.
    [05/07/2013 01:20:27.0591] [0] Schema Update Required Status : 'False'.
    [05/07/2013 01:20:27.0591] [0] Organization Configuration Update Required Status : 'False'.
    [05/07/2013 01:20:27.0591] [0] Domain Configuration Update Required Status : 'False'.
    [05/07/2013 01:20:27.0841] [0] Applying default role selection state
    [05/07/2013 01:20:27.0872] [0] Setup is determining what organization-level operations to perform.
    [05/07/2013 01:20:27.0872] [0] Because the value was specified, setup is setting the argument OrganizationName to the value DOMAIN.
    [05/07/2013 01:20:27.0872] [0] Setup will run from path 'C:\Windows\Temp\ExchangeSetup'.
    [05/07/2013 01:20:27.0888] [0] InstallModeDataHandler has 0 DataHandlers
    [05/07/2013 01:20:27.0888] [0] RootDataHandler has 1 DataHandlers
    [05/07/2013 01:20:27.0903] [0] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.  See
    the Exchange setup log for more information on this error.
    [05/07/2013 01:20:27.0935] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency. 
    See the Exchange setup log for more information on this error.
    [05/07/2013 01:21:04.0154] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
    [05/07/2013 01:21:04.0154] [0] End of Setup
    [05/07/2013 01:21:04.0154] [0] **********************************************

    Hi,
    The cause is clearly described in the log:
    [05/07/2013 01:20:11.0794] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency. 
    See the Exchange setup log for more information on this error.
    [05/07/2013 01:20:11.0794] [0] [ERROR] Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.
    I'd suggest you check NIC settings and AD configuration.
    Hope it is helpful.
    Fiona Liao
    TechNet Community Support

  • "Setup encountered a problem while validating the state of Active Directory: Exchange organization-level objects have not been created, and setup cannot create them because the local computer is not in the same domain and site as the schema master. Run se

    Team,
    I am trying to Install Exchange on my Lab, getting below error
    message.
    The Schema Role is installed on Root Domain and trying to install
    exchange on Child domain.
    1 Root Domain - 1 Child domain. both are located on single site.
    “Setup encountered a problem while validating
    the state of Active Directory: Exchange organization-level objects have not been created, and setup cannot create them because the local computer is not in the same domain and site as the schema master. Run setup with the /prepareAD parameter and wait for
    replication to complete.”
    Followed below articles:
    http://support.risualblogs.com/blog/2012/02/21/exchange-2010-sp2-upgrade-issue-exchange-organization-level-objects-have-not-been-created-and-setup-cannot-create-them-because-the-local-computer-is-not-in-the-same-domain-and-site-as-the-sche/
    http://www.petenetlive.com/KB/Article/0000793.htm
    transferred the schema roles to different server on root domain, still no luck.
    can someone please help me.
    regards
    Srinivasa k
    Srinivasa K

    Hi Srinivasa,
    I guess, you didn't completed the initial setup schemaprep and adprep before starting the installation. You can do it as follows:
    1. Open command Prompt as administrator and browse to the root of installation cd and run Setup.exe /PrepareSchema /IAcceptExchangeServerLicenseTerms
    After finishing this,
    2. Setup.exe /PrepareAD /OrganizationName:"<organization name>" /IAcceptExchangeServerLicenseTerms
    3. To prepare all domains within the forest run Setup.exe /PrepareAllDomains /IAcceptExchangeServerLicenseTerms. If you want to prepare a specific domain run Setup.exe /PrepareDomain:<FQDN of the domain you want to prepare> /IAcceptExchangeServerLicenseTerms
    4. Once you complete all of the 3 steps, install the pre-requisities for Exchange 2013
    5. Finally, run the setup program
    Hope this will help you
    Regards from Visit ExchangeOnline |
    Visit WindowsAdmin

  • I am facing call drop problem (incoming

    I am facing call drop problem in my I phone 5 since morning today, Outgoing & incoming both.
    However i switched off the handset & also pull out SIM from the Handset, again insert & reset the functions but it's stilll not working.
    Please help.

    Hi there Kuldeep Mishra,
    You may find the troubleshooting steps in the article below helpful.
    iPhone: Troubleshooting issues making or receiving calls
    https://support.apple.com/kb/TS3406
    -Griff W. 

  • Hey Verizon / HTC / Google  Please fix the caller ID problem, post 2.2 Froyo UPDATE.

    Hey Verizon / HTC / Google  Please fix the caller ID problem, post 2.2 Froyo UPDATE.  This is a major Problem. 

    I have provided some steps below that may help with the Caller Id issue you are experiencing.
    Try completing a soft reset on the device. A soft reset would be powering the device off and pulling out the battery. Once the battery is removed, place it back in and power the device back on.
    Dial *228 and send. Once dialed, listen for the recording to prompt you for option 1 and select option 1. The phone should complete its programming within a minute.
    Ensure you are using the area-code and 7 digit number format (ex. 9999951212)
    Try removing the contact and re-adding it.

  • Unable to setup Caller Id - New Zealand

    Hi,
    I am trying to setup caller ID from last few weeks and i am always getting below error:
    Unable to send code at this time
    We were unable to send you a confirmation code at this time.
    Please try again later.
    Details:
    User Type: Monthly Subscription User
    Country: New Zealand.
    Please help.

    Hey no wonder, it's The Fantastic Microsoft. Don't expect the fix any time soon. I have been waiting for the support representative for an hour to ask, apparently they're very busy *****
    Edited to conform with the Community Guidelines

  • Unable To Setup Call Forwarding - Receive Message ...

    Unable To Setup Call Forwarding - Receive Message "oops the server is not responding"
    have tried 3 different web browsers, chrome, ie and firefox and also tried our 3 outgoing internet lines all with different suppliers but when I go to add a call forwarding number it does nothing and I get the "oops" message.
    What's going on here, I need this urgently for business!

    for the call forwarding you need balance in your account and you can forward from the web browser or sky msn option also if need assistance you can connect with us

  • Verizon Call Assistant Problem

    I am trying to setup Call Assistant but the system shows a phone number that was changed a long time ago.
    How can I get this info updated to my current number?
    Thanks,
    Dave G

    Dave you can reach out to our Verizon Call Assistant team @ 1-888-483-5156 Monday-Friday 07:00am-6:00pm/PT, 09:00am-08:00pm/CT, 10:00am-09:00pm/ET.  They will be able to assist you in updating the system to the correct phone number. 
    Ian_VZ
    Verizon Support
    Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

  • Setup call forwarding

    I can't setup call forwarding to my mphone phone. I'm getting the error that I need to use the international dialing standard.&lt;br&gt;&lt;br&gt;I used (with and without spaces):&lt;br&gt;+1236xxxxxxx&lt;br&gt;1236xxxxxxx&lt;br&gt;xxxxxxx&lt;br&gt;&lt;br&gt;Where xxxxxxx is my actual phone number. Is it because the 236 area code is new, or how does this international dialing format supposed to look like?

        Hi Xibir,
    Oh no! Call forwarding is a great feature, and I am sad to hear that your having issues activating this feature. Let's get this fixed. To set an Immediate Call Forwarding from your work phone,
      • Dial *72 then the 10-digit phone number of your personal phone.
      • press Send and wait for confirmation beeps/message, and
      • press End.
    If this does not work, please accept my follow & send us a Private message with your work mobile number. We can set this forwarding up for you.
    Thanks,
    PamelaF_VZW
    Tweet us @vzwsuport

  • How to setup call forwarding

    I am trying to setup call forwarding but unable to do as
    I know it is not that much difficult but prob I am facing is
    That when I try to put the number it does not give any option
    To confirm which mean the setup did not complete

    Hi Scooter,
    There are a few ways this can be done Have a look in CUCM under
    Call Routing> Directory number and see if it's set up there. You can have a DID/DN
    with Call Forward set up without an actual phone by doing it via this config.
    You can also check Device > CTI Route Point as the same "virtual" config can be set there as well.
    Cheers!
    Rob
    "Show a little faith, there's magic in the night" - Springsteen

  • Caller display problem

    been having problems with my caller display it has been reported several times in last 3 weeks
    engineers came out and said it was my telephone at fault
    now tried 3 different brand new phones in the master socket and all just display "incoming call"
    tried a neighbours phone and it did work
    of the 3  new phones 2 were bt and one panasonic
    dialing  *234# says callers number will be displayed although this only started doing this yesterday usually it says service not available
    do you have any suggestions

    sorry, but you just have to be persistant and determined
    I've has smiliar issues setting up call blockers ( which need caller ID )
    Have gone through a number of these and different phones .
    After isolating the issues, finally system has stabilised ..
    One thing to make sure of is that BT have actually enabled it
    you have to called customer services ( don't make a new order )
    my BT Bill online still keeps saying:
    "extra calling features available" - incude BT Caller diaplay ( free for a year etc )
    its so frustrating, because I have this setup , yet the Bill looks like I need to order it 

  • Setup = Call adobe customer support

    I am trying to install the pixelbender toolkit on a Mac pro
    running 10.5.6. I downloaded the dmg and tried to click the "setup"
    icon and it informs me I should call adobe customer support.
    Adobe support doesn't handle this issue.

    Hey,
    Sorry to understand you are having problems installing the
    Toolkit. I'd like to help you out but I need a bit more
    information. For example, the language of your operating system,
    whether or not you've installed earlier versions of the Toolkit,
    etc.
    Let us know and thanks!
    samantha

Maybe you are looking for