GRE over MPLS not working...

Hi
I've a GRE tunnel configured between a CE and a PE.
I guess the problem is on the PE side, this is my config:
interface Loopback99
ip vrf forwarding dar
ip address 99.99.99.99 255.255.255.255
interface Tunnel199
ip vrf forwarding dar
ip address 11.11.11.1 255.255.255.252
ip policy route-map dfbit
tunnel source Loopback99
tunnel destination 88.88.88.88
tunnel path-mtu-discovery
Everything is reachable between PE and CE, but on the tunnel interface I wasn't able to find out the "tunnel vrf dar" command...
I've a Cisco 7206VXR (164 ram and 128 flash) and on the software feature navigator I wasn't able to find out an IOS support it..
Can anybody tell me why ?
Tks
Ric

Riccardo,
This feature is available starting with 12.3(2)T.
Regards

Similar Messages

GRE over MPLS

Hello people,
im facing problem trying to establish a GRE tunnel over mpls. The topology goes as follows:
(server) ----CE1(6500)-----PE1(6500)----vrf cloud-----CE2(6500)--FW
-server needs to establish a gre tunnel with FW.
-server receives a default route from CE1 via OSPF.
-CE1 has an default static route pointing to the next hop which is an interface VLAN (in a vrf) on PE1.
- PE1 receives a default route generated by CE2 (via mpbgp).
In this situation the GRE tunnel wouldnt come up.The only way i got the GRE to work was replacing the default static route on CE1 with a more specific static route.
On both cases (default AND specific static routes) the connectivity(ping) from end to end was there.
Has anybody seen anything alike?
thanks,
Bruno

You could be looking at some recursive routing throug the GRE interface, so the second it comes up it will try to put the GRE packets through the GRE tunnel, this creating a loop. Are you using a dynamic routing protocol to get network info over the GRE tunnel or a static route if so, how is it setup ?

MMS over WiFi not working after Sense 6 Update

A week ago Monday, the Sense 6 update hit my phone. Once loaded, I could no longer send MMS over WiFi, stream Google Play Music over WiFi, access my content on Google Play Books, or back up my pics to Google Cloud over WiFi. After several days of e-mails back and forth with HTC, it was determined that I had to perform a Hard Reset and lose all my information. This after clearing the cache, re-booting, various Safe Mode re-boots, etc. Nothing worked. I finally gave in and performed the hard reset. Now, the only thing NOT working is MMS over WiFi. I've tried other WiFi networks and still no MMS functionality. After about 10 minutes, I get a red triangle next to the message and an error notification, "Generic Network Failure."
This is going to start costing me money. Like so many of us, I no longer have unlimited data. Now, every time I want to send an MMS, I have to use my data plan. Not cool. I'm hoping that someone sees this and is working on the problem. I love my HTC One (M7), I really do. But, we're talking basic smart phone functionality. Without it, I'll be looking for another phone, and perhaps even another carrier. I'd prefer not to do that, but so be it. Please, Verizon, a little help?
For what it's worth, the MMS does this first. Notice the little MMS icon with the clock lower right...it just hangs there first...and sorry about the shoe pic.
Next, it does the Red Triangle thing...
And that's all I know. Perhaps someone here, or a kindly VZW employee will see this and take pity. Thanks!

I am having the exact same issue with my HTC one, which started immediately after updating to sense 6. Very annoying since I do not have unlimited mobile data plan, so I have to manually turn mobile data on each time I want to send or receive mms texts, including texts with multiple recipients. Did not have this issue before the update. Love this phone, my very first smartphone. But it is hard to believe that I was able to send pics over text with my old flip phone with no data plan. And now I can't with the HTC. I just can't have the mobile data on at all Times. It has become very inconvenient ever since the upgrade. Wish I had never done sense 6.

URL redirect over is not working..

Redirecting URL appended with querystring parameters for community is not working on SSO? We have SSO set up using Intergrated Windows Authetication.
When I launch new browser and request portal over SSO , works. Then I go to a community and copy the URL from browser. When I open new window and paste the URL extracting UserID from it, it gives me login screen and sso won't work.
If I do the same action twice in same window(for which I got the login screen firsttime), it works second time. How can I resolve this? Is anybody had this problem before?
Thanks!!
Sanjay

CaptureDeviceInfo di=null;
               Vector deviceList = CaptureDeviceManager.getDeviceList(new VideoFormat(VideoFormat.RGB));
               if (deviceList.size() > 0)
                         di = (CaptureDeviceInfo)deviceList.elementAt(0);
                         if(di==null) System.exit(-1);
                              System.out.println("devicelist2");
                    else
                         System.out.println("exit");
                         System.exit(-1);
               MediaLocator mediaURL = di.getLocator();
create medialocator by using datasouce object's mehtod getLocator();
anoop

[Solved] Remote X over ssh not working

Hello, I'm trying to forward X11 over ssh but it's not working.
I type
ssh -X 192.168.1.101
followed by my password, and I log in just fine.
I try to launch an X11 application and I get
$kate
kate: cannot connect to X server
SSH is supposed to be forwarding a dummy $DISPLAY to allow remote X. So I type
$echo $DISPLAY
and and get back a empty newline.
Well how about
$xinit
Fatal server error:
Server is already active for display 0
If this server is no longer running, remove /tmp/.X0-lock
and start again.
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
Okay, I'll shut down xserver.
I do it, and type
$xinit
again. KDE launches on my remote box. It makes sense, but contradicts many guides I have read which say it should launch on my local machine.
What am I doing wrong here? This should be ridiculously simple.
Last edited by xenobrain (2010-07-06 20:45:16)

Did you enable X forwarding in your sshd config?
Did you xhost + (or ssh -Y)?
Did you crop your DISPLAY variable in a bashrc or similar script run at login?
Last edited by benob (2010-07-06 19:10:54)

Voicemail over Bleutooth not working. Calling oke.

Hi,
Sins 4.2.1. update my voicemail over Bleutooth is not working in the car. Calling is no problem, only voicemail is. I can listen to my voicemail over the intern speakers. Not the earspeaker when i am in my car. Anybody a solution?
Rob
(iPhone 4 origineel simlockfree)

I filed a bug report with Apple and sent them logs as the problem was occurring. Apple is aware of this issue and seems they are working on it.... See Reply from Apple Below...
This is a follow up to Bug ID# 8716239. After further investigation it has been determined that this is a known issue, which is currently being investigated by engineering. This issue has been filed in our bug database under the original Bug ID# 8584516. The original bug number being used to track this duplicate issue can be found in the State column, in this format: Duplicate/OrigBug#.
Thank you for submitting this bug report. We truly appreciate your assistance in helping us discover and isolate bugs.
Best Regards,
Apple Developer Connection
Worldwide Developer Relations

Time Machine backup over wifi not working after upgrade to 10.6.3

I have a firewire external hard disk connected to directly into my imac which I use for back-up. The imac is wired into an ethernet LAN. I also backup my MacBook Pro to the same hard disk. The MacBook is connected to the backup disk via a wifi link to a router. All has been working well until I upgraded Snow Leopard to 10.6.3 and now the back-up is not working for the MacBook. The same thing happened after the last point release upgrade but at the time I thought it must have been user error. Last time I had to trash the backups and start from scratch. Can anyone shed any light?

Try reselecting the drive (from the laptop) via TM Preferences > Select Disk (first select the "none" drive, then the correct one).
If that doesn't help, try a "full reset" of TM on the laptop, per #A4 in the Time Machine - Troubleshooting *User Tip,* also at the top of this forum.

Polling over https not working

Hi,
How do I change below to make it work with https? I tried with AMFSecureChannel but that did not work. Appreciate any help... thanks!
<channel-definition id="my-amf-poll" class="mx.messaging.channels.AMFChannel">
    <endpoint
        url="http://{server.name}:{server.port}/{context.root}/messagebroker/amfpoll"
        class="flex.messaging.endpoints.AMFEndpoint"/>
    <properties>
        <polling-enabled>true</polling-enabled>
        <polling-interval-seconds>1</polling-interval-seconds>
    </properties>
</channel-definition>

Hi
I think you don't need to do all these things. With default setting create a HTTPService component and assign the required url to it. You can assign the resultFormat.Call the send() method. Optionally you can pass argument to it.
Hope this helps
Rush-me

[SOLVED] Brightness control over keyboard not working, but it works...

Hello,
I recently got a new laptop at work and I put a fresh Arch on it.
Almost everything works perfectly, but I have one weird issue.
I can control backlight of my display via ACPI; I wrote a simple script for it:
pabre@pbr-laptok:~$ cat /usr/local/sbin/brightness.sh
#!/bin/bash
DEV=/sys/class/backlight/intel_backlight/brightness
MAX=`cat /sys/class/backlight/intel_backlight/max_brightness`
ACT=`cat /sys/class/backlight/intel_backlight/actual_brightness`
MIN=0
STEPS=10
STEP=$((MAX/STEPS))
if [ $1 == "+" ]; then
if [ $((ACT+STEP)) -le $MAX ]; then
echo $((ACT+STEP)) > $DEV
fi
elif [ $1 == "-" ]; then
if [ $((ACT-STEP)) -ge $MIN ]; then
echo $((ACT-STEP)) > $DEV
fi
fi
exit 0
I put myself a sudoers entry for it:
root@pbr-laptok:~# cat /etc/sudoers | grep pabre
pabre ALL=(ALL) NOPASSWD: /usr/local/sbin/brightness.sh,/usr/bin/pacman -Sy
And it works like a charm, when run from a terminal:
pabre@pbr-laptok:~$ sudo /usr/local/sbin/brightness.sh -
So, my next step was to bind that script to appropriate keys on my keyboard (Fn + UP/DOWN - which are XF86MonBrightnessUp and XF86MonBrightnessDown)
My window manager is Awesome, so I put to the config:
awful.key({ }, "XF86MonBrightnessUp", function () awful.util.spawn("sudo /usr/local/sbin/brightness.sh +") end),
awful.key({ }, "XF86MonBrightnessDown", function () awful.util.spawn("sudo /usr/local/sbin/brightness.sh -") end),
among others like touchpad toggling, volume control, etc (which are working without issues)
And now, guess what... Those keys fire that script, change the brightness and after second or less - it comes back to old value! You can see that display blinks (for example gets brighter and moment after - it goes back to previous state).
I tried to debug it, putting to the script something like:
if [ $1 == "+" ]; then
if [ $((ACT+STEP)) -le $MAX ]; then
echo $((ACT+STEP)) > $DEV
cat /sys/class/backlight/intel_backlight/actual_brightness >> /tmp/br.log
sleep 1
cat /sys/class/backlight/intel_backlight/actual_brightness >> /tmp/br.log
fi
And the first entry was that what it was supposed to be, while te other (second after) Was again the old value.
Does anybody have any idea what "reverts" my changes to the /sys/class/backlight/intel_backlight/brightness and why it works without issues when simply run from a terminal?
Last edited by PaBre (2014-03-16 17:10:54)

I think that I've found partial answer.
When I changed key binds to another keys - it works!
But even then, when I press XF86MonBrightnessUp or XF86MonBrightnessDown, the brightness level gets reset. And now they are not bind to anything (at last not explicit).
So it looks that I have to found how to decouple the internal, not working as expected, bind to these keys.

Apple remote desktop over vpn - not working

Hi,
I've been using ARD within my firewall and it's been working great. I am currently traveling and logged in via VPN (PPPT) for the first time and although I can see the computers (two) that I want to log into, I am not able to connect to them.
I am able to access my file server fine, it just seems to be ARD that does not work... I have an Asus RT-N66U as my router/VPN server.
HELP!!!!

have you tried scanning the network in ARD while connected via VPN

USB audio input to voice-over tool not working

with FCE-HD on iMac i have system preferences set to USB-122 Tascam box for audio input/output (works great with GB for instance) but when i try using it for audio input on FCE and the voice-over tool set to USB-122, i hear no audio, the level meter doesn't more, etc, its still taking the audio from the built-in mic.
im sure its something simple im overlooking??
tia

Mark,
See if this post helps. Not familiar with USB audio devices myself, but found this searching:
John Hayward, "Audio out from FCE HD to USB audio iMic" #1, 10:11am Oct 4, 2005 CDT

MAPI over HTTP not working correctly, Outlook 2013 clients prompting for credentials during profile creation or opening depending on security of virtual directory

ENVIRONMENT
-1 Exchange 2013 SP1 CU7 server with all roles that is also a hybrid server with Office 365 tenant, mailboxes are all on premise only LYNC online is being utilized right now.
-Exchange 2013 public folders
-Mix of Outlook 2013 SP1 and Outlook 2010 SP3 clients all fully update to day as of Feb 2015
Outlook anywhere is working perfectly across all clients both internally and externally using autodiscover. Both Outlook 2013 and 2010 clients can open the program and create a profile automatically via autodiscover and no additional logon prompts
are seen.
We set the internal and external mapi virtual directory URLs to a valid URL that also matches the Exchange 2013 SSL certificate. We set the security to ntlm, negotiate on the mapi virtual directory. We reset IIS and enabled mapi over http in
the org config. We run in to problems here.
Outlook 2010 clients appear to be working fine. We can create a new profile and open and close Outlook without any logon prompts and verify that MAPIHTTP and Negotiate are used to connect to Exchange.
Outlook 2013 clients are having problems. As soon as we try to create a profile it says your administrator has made a change that requires you to restart outlook and then a windows logon prompt appears. If we authenticate Outlook will open and connect.
This logon prompt should not occur. We can confirm that it is connecting via MAPI HTTP and Negotiate.
If we set the mapi virtual directory to NTLM only then a logon prompt also appears during every open of Outlook 2013. We can confirm that it is trying to connect with MAPIHTTP via NTLM in the outlook connection test screen.
I do not understand this behavior by Outlook 2013 which was supposed to be designed with MAPI HTTP in mind. I would think the same issues would occur with Outlook 2010 but they do not. I am not sure how to resolve this and I am looking for help.

I have the same problem. Exchange and Outlook are both up to date. After creating a new profile Outlook prompts for username/password. A lot of users also get this prompt while
working - the profiles have been "migrated" from Exchange server 2010. <o:p></o:p>
Niko, as i can see in your screenshot you do not have Mapi over HTTP enabled. Why? You can change settings in the security tab – if you have Mapi over
HTTP enabled all options are grayed out (please correct me if I
am wrong):
This is a very annoying thing – does anybody else have the same problem?
Any suggestions on this?
Marc

5.1 over analgue not working, 5.1 over digital work

I have the 24 bit external li've sound card plugged into my laptop via usb. Well i connected it into my reciever via digital coax and i can get DD. But if i connect it via analogue wires(http://www.radioshack.com/product/in...entPage=search) i can only get sound through the front 2 speakers. I have a 5. set up but in the testing its only front L/R. But if i switch it to spdif it works for dd. I have CMSS enabled and i have 5. set as my speakers but it still doesnt work. Any ideas?

3
It seems like it should be working but its not
I wonder why the card isnt trying to send sound over those wires when its set to 5., if it was the wires being messed up then why would the left and right speaker worK?

Facetime over cellular not working (at&t)

So we just switched over to an AT&T Mobile Share plan and we're supposed to be able to facetime over cellular now, but it almost never works.
You click on the facetime button, and it just waits and waits and waits, and the person on the other end never gets a request. I know it's not an issue with them not allowing it because we were able to get it to work 1 time out of about 20 attempts (plus it used to give a nasty message and we can setup hotspots now.)
The mobile sharing plan is activated, so facetime should be good to go.
I think what is going on is that it's losing network connectivity. We'll be on LTE, get a phone call, fall off LTE because on AT&T you drop down to 3G when on the phone, and then you hit facetime, and you're still on 3G, and/or your phone hasn't made a connection yet, and then it's stuck in some sort of limbo between cell networks.
It really stinks, because I actually really wanted the ability to do this and was actually going to be using it.
I'm hoping this clears up somehow, or I find a solution... but I'm pretty annoyed. It's supposed to just work, and if it only works 1 time out of 10, I'll just never even try and it's 100% useless.
I'm not sure if this is Apple's fault or AT&T, but I want a solution.
I dropped out of my unlimited data plan to switch over to a mobile share plan, and facetime over cellular was one of the main reasons. If it's not going to work, I'm going to be pretty upset.

More than likely it is an AT&T problem. I have sprint and FaceTime over cellular works great. Not as good quality as wifi but way better than Skype. AT&T is only after your money. With sprint I have unlimited data and not restricted like AT&T does.

Mousing over program not working

Seems to be an issue with hovering over Spotify. Instead of showing the options to pause or skip forward/backward, nothing happens. It seems Spotify is buggin out and showing itself as the forefront window, even when it's not. As a result, highlighting the program is not bringup the "preview window" as it were, because it already thinks it's at the forefront. This makes it incredibly annoying to skip tracks and pause, since you have to switch to the window instead of just using the shortcut. This is on WIndows 7.

First, quit the editor, then restart it while holding down ctrl+alt+shift. Keep the keys down till you see a window asking if you want to delete the settings file. You do. Note that if you have set the welcome screen to automatically open the editor, it won't work from that shortcut. Use the actual .exe/application file or the buttons in the organizer or on the welcome screen.

GRE over MPLS not working...

Similar Messages

Maybe you are looking for