H323 cisco attributes not being forwarded to Radius accounting server

I have enabled a Radius server to gather AAA Accounting CDR records but I don't see any of the Cisco h323 attributes. The following is an example of the list I WANT to see.
ATTRIBUTE h323-remote-address 23 string Cisco
ATTRIBUTE h323-conf-id 24 string Cisco
ATTRIBUTE h323-setup-time 25 string Cisco
ATTRIBUTE h323-call-origin 26 string Cisco
ATTRIBUTE h323-call-type 27 string Cisco
ATTRIBUTE h323-connect-time 28 string Cisco
ATTRIBUTE h323-disconnect-time 29 string Cisco
ATTRIBUTE h323-disconnect-cause 30 string Cisco
ATTRIBUTE h323-voice-quality 31 string Cisco
ATTRIBUTE h323-gw-id 33 string Cisco
ATTRIBUTE h323-incoming-conf-id 35 string Cisco
I see a lot of stuff comming in, but I don't see any of the attributes above.
PS. when I do a DEBUG AAA ACCOUNTING here's what I see.
*Oct 8 18:00:19.681: AAA/ACCT/CONN(00001863): STOP protocol reply FAIL
*Oct 8 18:00:19.681: AAA/ACCT(00001863): Accouting method=NOT_SET
Here's my config
aaa new-model
aaa group server radius ACS
server X.X.X.X auth-port 1645 acct-port 1646
aaa authentication login h323 group ACS
aaa authentication login no_rad local
aaa accounting update newinfo
aaa accounting exec default start-stop group ACS
aaa accounting connection default start-stop group ACS
aaa accounting connection h323 start-stop group ACS
aaa session-id common
gw-accounting aaa
attribute acct-session-id overloaded
attribute h323-remote-id resolved
acct-template callhistory-detail
radius-server host X.X.X.X auth-port 1645 acct-port 1646
radius-server timeout 60
radius-server key XXXXX
radius-server authorization permit missing Service-Type
radius-server vsa send accounting
radius-server vsa send authentication
dial-peer voice 447 voip
destination-pattern 1647280....
voice-class aaa 1
session target ipv4:X.X.X.X
Any ideas?
thanks,
Paul

Try the following command:
gw-accounting h323 vsa
See here (http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122tcr/122tvr/vrg_g1.htm#wp1505752) for details.

Similar Messages

VOIP calls not being forwarded from GW to GK and visa versa

I have a VOIP network setup in place using 2691 routers. i have a siemens PBX connected to the 2691 routers using an E1 controller (running QSIG), my WAN interface between the two sides is an ATM interface. when i do a csim start from one router to the extension on the other side the call goes through and the phone rings. However, when i actually dial from one extension to the other, the call is not being forwarded. and what happens is that i hear the dial tone again on the phone im dialing from.
I have taken some debugs but still could pin point the problem, even though in the ccapi inout debug i found that when it tries to look for a node, it doesnt find it.
I have attached the configuration for both sides. Along with the debug from one of the sites.
There are a couple of GW's associated with the GK.
The ones im concerned about are Mussalla_GW & GK-HO.
Thank You in advance
Mouhannad

Try this:
dial-peer voice 2 pots
direct-inward-dial
Without this command the router will not collect the digits coming across the PRI.
Please rate helpful posts.

Calls not being forwarded to skype number

Hello, I have had my Skype number for 2 years now and never had a problem.However since end of November 2012 calls from the USA are no longer being forwarded to my cellphone in Germany.No , I have not changed my settings , why should I , since it has been working perfectly all these years.There is no way to get help from Skype and I am extremely frustrated with their service.It sucks to pay for a product that won´t work.I am a dissatisfied customer and will leave them if they do not straighten out their stuff.

watsource wrote:
Hello, I have been a SKYPE user for the past 5 years and everything has been working fine. Recently, calls from telephones to my skype number are not being forwarded to my designated number. I've tried to turn off and on forwarding feature but still not working. Calls from other skype contacts using skype calling me are forwarded but not from any landline or mobile contacts calling my skype number.
What happens when you call your Online Number?
If calls directly from other Skype users are being forwarded to your designated number, but not the calls made to your Online Number, call-forwarding appears to be working. You may have a different issue related to your Online Number. Has it expired? If you click on "Account" at the top of this page, you can verify that your Online Number is still in effect by clicking on "Online Number" once you log into your Skype account through that link.
If your Online Number is still in effect, here's something else to check. From a computer (not the Skype app on a mobile phone or other device), can you verify the Privacy setting for Online Numbers? It should be set to allow calls from anywhere. If not, it is possible that this setting was changed, preventing you from getting calls on the Online Number.
Patrick
Location/Ubicacion: Arizona USA
Time Zone/Hora Local: UTC/GMT -7
If this message has adequately addressed your issue, please click on the “Accept as Solution” button. If you found a post useful then please "Give Kudos" at the bottom of my post, so that this information can benefit others.
Si esto mensaje le ha ayudado, por favor haga clic en "Aceptar como solución". Si encuentra un mensaje útil, por favor "Da Kudos" al final del mensaje, por lo que esta información puede beneficiar a otros.
I am not a Skype employee. No soy un empleado de Skype.

[svn:osmf:] 14982: Fixing some event parameters not being forwarded.

Revision: 14982
Revision: 14982
Author:   [email protected]
Date:     2010-03-24 02:15:50 -0700 (Wed, 24 Mar 2010)
Log Message:
Fixing some event parameters not being forwarded.
Modified Paths:
    osmf/trunk/apps/samples/framework/OSMFPlayer/src/DebuggerElementProxy.as

Hi,
Thanks for posting in Microsoft TechNet forums.
I will try to involve someone familiar with this topic to further look at this issue. There might be some time delay. Appreciate your patience.
Thank you for your understanding and support.
Kate Li
TechNet Community Support

Network Policy Server Event ID 6272 not being forwarded to Event Collector.

Hi there
I have configured an Event Subscription to collect events from 2 DCs that run RADIUS for network switches. It appears the events are being forwarded okay, I am getting the Security events (Logon and Logoff) on the event collector PC. However I am not getting
any of the Network Policy Server security events (specifically Event IDs 6272), to centrally audit RADIUS logins to switches.
The subscription is collector initiated, and I have added Network Service to the Event Log Readers Group. Is there something I am missing in the setup requirements for these events to be forwarded?
Thank you,
Kind regards
Hylton

Hi Gabriel101,
Could you offer us more information about your environment, such as what edition server you are using, whether your AD and NPS role on the same server, whether your NPS working
properly now, whether you can receive others security auditing.
The related KB:
NPS Local Log File Status
http://technet.microsoft.com/en-us/library/cc735386(v=ws.10).aspx
Event ID 6272 — NPS Authentication Status
http://technet.microsoft.com/en-us/library/cc735388(v=ws.10).aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Voip: CLI is not being forwarded

Dears,
I connected cisco 3800 router with ericsson MD110 exchange using QSIG over E1 Pri. Calls are forwarding properly over ip network but few features are not being enabled specially CLI feature. I found a documnet where a command "caller-id enable" was issue in voice-port interface. But i go in this mode using command voice-port 1/0:15, no command caller-id find. My topology is below:
MD110 PBX ----3845---------3825----MD110 PBX
Waiting for immediate positive response.
Regards
Rameez

R1#
Oct 30 13:19:12.465: ISDN Se1/0:15 Q931: RX <- SETUP pd = 8 callref = 0x3684
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18381
Preferred, Channel 1
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x0181, N/A
Plan:ISDN, Type:Unknown
Called Party Number i = 0x81, '3'
Plan:ISDN, Type:Unknown
Shift to Codeset 5
Codeset 5 IE 0x31 i = 0x80
Shift to Codeset 5
Codeset 5 IE 0x32 i = 0x81
R1#
Oct 30 13:19:12.469: ISDN Se1/0:15 Q931: TX -> SETUP_ACK pd = 8 callref = 0xB684
Channel ID i = 0xA98381
Exclusive, Channel 1
Oct 30 13:19:13.005: ISDN Se1/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x3684
Called Party Number i = 0x81, '0'
Plan:ISDN, Type:Unknown
R1#
Oct 30 13:19:13.481: ISDN Se1/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x3684
Called Party Number i = 0x81, '0'
Plan:ISDN, Type:Unknown
Oct 30 13:19:14.429: ISDN Se1/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x3684
Called Party Number i = 0x81, '1'
Plan:ISDN, Type:Unknown
R1#
Oct 30 13:19:14.577: ISDN Se1/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xB684
Oct 30 13:19:14.693: ISDN Se1/0:15 Q931: TX -> ALERTING pd = 8 callref = 0xB684
Facility i = 0x9FAA068001018201018B0100A1080201020201018000
Progress Ind i = 0x8188 - In-band info or appropriate now available
Oct 30 13:19:14.737: ISDN Se1/0:15 Q931: RX <- FACILITY pd = 8 callref = 0x3684
Facility i = 0x9FAA06800100820100A406020102810102
R1#
Oct 30 13:19:20.841: ISDN Se1/0:15 Q931: TX -> CONNECT pd = 8 callref = 0xB684
Progress Ind i = 0x8182 - Destination address is non-ISDN
Connected Number i = 0x0181, '3001'
Shift to Codeset 5
Codeset 5 IE 0x32 i = 0x81
Oct 30 13:19:20.901: ISDN Se1/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x3684
R1#
Oct 30 13:19:32.625: ISDN Se1/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0xB684
Cause i = 0x8190 - Normal call clearing
Oct 30 13:19:32.681: ISDN Se1/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x3684
Cause i = 0x8190 - Normal call clearing
Oct 30 13:19:32.681: ISDN Se1/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xB684
R1#u all
All possible debugging has been turned off
R1#
Output of Router R2 you will find in my next post as i have to split output due to character limit.
Regards

WINS traffic not being forwarded

Hi folks,
For some reason, it seems that my WINS traffic isn't being forwarded across subnets over our 3750's. This is causing the workstations to have a "hit and miss" with authentication. I have enable "ip helper-address", "ip forward-protocol udp 137/138", even tried "ip directed-broadcast".
If I create create an LMHOST file, it works everytime. "Enable NetBIOS over TCP/IP" is enable on WinXP Clients. On Win98 clients receives it's setting from dhcp.
PCa---Vlan1 --<>-- Vlan2 ---- WINS Server / Authentication
Thanks..
-- Dominique

Hi Everyone,
This is how I have the device currently configured:
<..snip..>
ip dhcp excluded-address 10.203.8.1 10.203.8.29
ip dhcp pool 10.203.8.0/24
network 10.203.8.0 255.255.255.0
default-router 10.203.8.1
dns-server 10.70.0.9 10.70.0.6
domain-name rainbowschools.ca
netbios-name-server 10.203.0.7
netbios-node-type h-node
<..snip..>
!! Example Interface Configuration !!
interface FastEthernet1/0/23
description Academic
switchport access vlan 108
switchport mode access
no cdp enable
spanning-tree portfast
!! Server VLAN interface !!
interface Vlan100
ip address 10.203.0.1 255.255.255.0
!! Academic VLAN interface !!
interface Vlan108
ip address 10.203.8.1 255.255.255.0
ip helper-address 10.203.0.7
ip directed-broadcast
!! IP Forward Protocol !!
ip forward-protocol udp netbios-ss
ip forward-protocol udp bootps
ip forward-protocol udp bootpc
--> Even when I enter "ip forward-protocol udp 137/138", it doesn't appear. So I am assuming it is on by default.
Thanks.
-- Dominique

Internal Order not being created in cProjects-Accounting Integration

Dear All,
We are working on cProjects 4.0 with ECC 6.0,
Trying to do Accounting Integration.
For only one Project I am able to create Internal Order,
But I am getting following error.
Cost/revenue rate YP002 is not valid in organization 00000000
Inspite of assigning these rates to the organization 00000000
For other projects, when I click on accounting:
I get following error
"Single-Obj.Controlling on InternalOrders 0188993B3E343947A046B554FD886E03 000006000032 does not exist"
When I go to Controlling Cockpit, I see this Internal Order not being created.
Have revisited all settings, project type, etc.
How do I go about this.
Kindly help,
Navendu

Dear All,
I was able to solve the one of the problem, with the following settings,
Assign Cost Elements & Activity Types:
Choose Organization, Start & End Dates, Cost and Revenue Elements, Currency.
The start and end date of the cost/ revenue did not fall within the start and end date of the Organization.
Regards,
Navendu Shirali

Port not being forwarded in WRT54GR

As Topic says, here are the screenshots in what I did, I even did DMZ but my ports are not forwarded.

1.
2.
Active Connections
Proto Local Address          Foreign Address        State
TCP    0.0.0.0:135            0.0.0.0:0              LISTENING
TCP    0.0.0.0:445            0.0.0.0:0              LISTENING
TCP    0.0.0.0:2869           0.0.0.0:0              LISTENING
TCP    0.0.0.0:5357           0.0.0.0:0              LISTENING
TCP    0.0.0.0:49152          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49153          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49154          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49155          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49156          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49157          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49893          0.0.0.0:0              LISTENING
TCP    127.0.0.1:49190        127.0.0.1:49191        ESTABLISHED
TCP    127.0.0.1:49191        127.0.0.1:49190        ESTABLISHED
TCP    127.0.0.1:49199        127.0.0.1:49200        ESTABLISHED
TCP    127.0.0.1:49200        127.0.0.1:49199        ESTABLISHED
TCP    192.168.1.110:139      0.0.0.0:0              LISTENING
TCP    192.168.1.110:49724    64.4.9.101:1863        ESTABLISHED
TCP    192.168.1.110:49733    64.4.9.97:1863         ESTABLISHED
TCP    192.168.1.110:49782    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49783    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49784    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49785    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49786    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49793    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49796    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49797    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49803    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49807    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49811    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49813    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49815    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49816    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49817    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49818    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49828    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49837    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49841    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49844    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49854    209.85.225.95:80       ESTABLISHED
TCP    192.168.1.110:49859    207.46.124.136:443     ESTABLISHED
TCP    192.168.1.110:49879    207.46.125.253:7001    TIME_WAIT
TCP    192.168.1.110:49883    154.20.137.56:55562    ESTABLISHED
TCP    192.168.1.110:49884    207.46.125.253:7001    TIME_WAIT
TCP    192.168.1.110:49885    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49886    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49887    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49889    65.55.194.253:443      ESTABLISHED
TCP    192.168.1.110:49890    65.55.194.253:443      ESTABLISHED
TCP    192.168.1.110:49891    207.46.113.93:443      ESTABLISHED
TCP    192.168.1.110:49892    207.46.125.253:7001    TIME_WAIT
TCP    [::]:135               [::]:0                 LISTENING
TCP    [::]:445               [::]:0                 LISTENING
TCP    [::]:2869              [::]:0                 LISTENING
TCP    [::]:5357              [::]:0                 LISTENING
TCP    [::]:49152             [::]:0                 LISTENING
TCP    [::]:49153             [::]:0                 LISTENING
TCP    [::]:49154             [::]:0                 LISTENING
TCP    [::]:49155             [::]:0                 LISTENING
TCP    [::]:49156             [::]:0                 LISTENING
TCP    [::]:49157             [::]:0                 LISTENING
TCP    [::]:49894             [::]:0                 LISTENING
UDP    0.0.0.0:123            *:*
UDP    0.0.0.0:500            *:*
UDP    0.0.0.0:623            *:*
UDP    0.0.0.0:664            *:*
UDP    0.0.0.0:3702           *:*
UDP    0.0.0.0:3702           *:*
UDP    0.0.0.0:4500           *:*
UDP    0.0.0.0:5355           *:*
UDP    0.0.0.0:60919          *:*
UDP    127.0.0.1:1900         *:*
UDP    127.0.0.1:50242        *:*
UDP    127.0.0.1:52704        *:*
UDP    127.0.0.1:60925        *:*
UDP    192.168.1.110:9        *:*
UDP    192.168.1.110:137      *:*
UDP    192.168.1.110:138      *:*
UDP    192.168.1.110:1900     *:*
UDP    192.168.1.110:7587     *:*
UDP    192.168.1.110:60924    *:*
UDP    [::]:123               *:*
UDP    [::]:500               *:*
UDP    [::]:3702              *:*
UDP    [::]:3702              *:*
UDP    [::]:5355              *:*
UDP    [::]:60920             *:*
UDP    [::1]:1900             *:*
UDP    [::1]:60922            *:*
UDP    [fe80::100:7f:fffe%11]:1900 *:*
UDP    [fe80::100:7f:fffe%11]:60923 *:*
UDP    [fe80::31e6:cdb:363c:5305%10]:1900 *:*
UDP    [fe80::31e6:cdb:363c:5305%10]:60921 *:*
Yeah I also have a voip connected, but I haven't tampered with the settings in that device yet, even though I DO have access to the settings, I don't really know how to tamper with it.
Thanks for the reply so far, got home late~

Emails Not Being Forwarded in a non-wireless environment...

This is very strange and I'm not sure if it's something I did or if there's something wrong with my phone..
I have my emails forwarded from my AOL account using TMobile's service. Up until now, I've not had any problems..
I also have my WiFi turned on in several locations which I frequent (my home, office and Starbucks). What is happening is my phone is not forwarding ANY of my emails, texts or PINs unless I'm in one of these WiFi locations. I've checked all of my connections and both my Mobile Network as well as my WiFi connections are both turned on.
I've tried resetting the phone many times, I've even recreated my email addresses in Blackberry Internet Service and still, NO EMAILS unless I'm within WiFi range..
Does anyone have any idea what's going on here? Did I accidentally switch something off or on that I shouldn't have that is blocking my email, texts & PINs?
Thanks in advance for your help.
Sophie
Message Edited by sophbakall on 01-04-2009 02:39 AM

You said you've reset your phone? Did you remove the battery and reboot it?
With the BlackBerry device powered ON, remove the battery a few seconds and then reinsert the battery to reboot.
Try also removing/deleting your Service Books for email accounts at Options > Advanced > Servcie Books, then readding them from your BIS account login.
Resend your service books from your carrier BIS site.
http://www.blackberryfaq.com/index.php/Where_can_I_log_into_my_BIS_account%3F
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

Email from specific email not being forwarded to BB

Since I have set up my owa email account on the BB, using BIS, there are emails I am unable to receive from specific users on the BB. These users are within the same domain as me and the emails are in my inbox when I log in to my account through IE. I also use an IMAP account on the BB and those users are copying that email and those emails are forwarded to the BB via that email, but not my email via OWA. Has anyone had this issue before, does anyone have any kind of solution to this problem?
We have already deleted and readded the email on the BB and nothing is working....
Any insight would be helpful.
Thanks

Look through the Cookie extensions at AMO for an extension that has the features you want.
[https://addons.mozilla.org/en-US/firefox/search/?q=cookies&cat=all&lver=any&atype=0&sort=&pid=1&pp=20&lup=&advanced= AMO search for "cookies" extensions]

Captivate 5: Acrobat Quiz Results Not being Forwarded - Screen Freezes.

After completing the quiz, then pressing the POST button, I fill in the required two fields; but, the screens freezes or remains on the ...signing in status indefinitely.
I tried all the security settings for my pc and the acrobat website with no success.
I tried various Captivate settings and still no solution.
Is there something else I could try, I need to temporaily use Captivates' Score Result feature until the LMS is online.
Thank You
iaustin

Hi,
Can you try repubklishing your course using Flash Playe 10 in settings of Publish options?
Can you add the location of your published output to Flash player, Global Security settings to Trusted Locations--
http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager04.htm l
Thanks,
Anjaneai

Invitations not being sent out on Calendar Server 6.3

We would be grateful for any help on this. We can give further details if needed, please just let us know.
Thanks very much.
Issue:
To our customers the calendars server appears to be fully operational and without error. However, when a customer creates a new event and invites other people to attend, no invites are sent out. The event creator, however, believes all is in order as no error messages appear and the list of invitees appears on the event. This was working recently. We have looked for things which have changed (e.g. disk space, size of files, corruption, recent patching, licenses expiring, etc) but have not yet found anything that has changed.
Some details of our system:
./cal/sbin/csversion
Oracle Communications Calendar Server 6.3-27.01 (built Feb 15 2011)
SunOS xxxx 5.10 Generic_142909-17 sun4u sparc SUNW,Sun-Fire-V440
In /var/opt/SUNWics5/logs/watcher.log , we get these notices and errors when we restart the service.
[20/Feb/2012:12:35:56 +1300] (Notice) Received request to restart: store admin http
[20/Feb/2012:12:35:56 +1300] (Notice) Connecting to watcher ...
[20/Feb/2012:12:36:00 +1300] (Notice) 7698
[20/Feb/2012:12:36:00 +1300] (Notice) Stopping http server 7704 ..... done
[20/Feb/2012:12:36:02 +1300] (Notice) Stopping http server 7705 ... done
[20/Feb/2012:12:36:02 +1300] (Notice) admin server is not running
[20/Feb/2012:12:36:02 +1300] (Notice) Stopping store server 7700 ............................................................... timeout
[20/Feb/2012:12:37:03 +1300] (Error) Cannot stop server store with SIGTERM, now retrying with SIGKILL
[20/Feb/2012:12:37:03 +1300] (Notice) Stopping store server 7700 ..... done
[20/Feb/2012:12:37:05 +1300] (Notice) Starting store server .... 7718
[20/Feb/2012:12:37:05 +1300] (Notice) Checking store server status ..... ready
[20/Feb/2012:12:37:07 +1300] (Notice) Starting admin server ....Watched 'csadmind' process 7725 exited abnormally
7725
[20/Feb/2012:12:37:08 +1300] (Notice) Starting http server ....[20/Feb/2012:12:37:08 +1300] (Notice) Received request to restart: store admin http
[20/Feb/2012:12:37:08 +1300] (Notice) Connecting to watcher ...
... 7727
[20/Feb/2012:12:37:13 +1300] (Notice) 7698
[20/Feb/2012:12:37:13 +1300] (Error) store failed twice in 600 seconds, will not perform restart
Watched 'csadmind' process 7844 exited abnormally
What we've done:
We have run db_verify and csdb -v check on the databases. ics50deletelog.db did have corruption, so we fixed that by using db_dump and db_load to export then import the databases.
We also purged the ics50deletelog.db database using cspurge afterwards when the dump and load didn't seem to have had an effect.
We tried putting the log level up in the /opt/SUNWics5/cal/config/ics.conf , but didn't get any more details when restarting the service (through /etc/init.d/sunwics5 restart)
Before we did the db_dump, db_load and purge:
Calendar database version: 4.0.0
Sleepycat Software: Berkeley DB 4.2.52: (December 3, 2003)
Total database size in bytes: 1465503744
Total number of calendars: 14964
Total number of events: 830842
Total number of tasks: 17351
Total number of alarms: 57181
Total number of gse entries: 9
Total number of master component entries: 24100
Total number of deletelog entries: 1779967
Total logfile size in bytes: 79262
Session database version: 3.0.0 [BerkeleyDB]
Total database size in bytes: 0
Total logfile size in bytes: 0
Counter database version: 1.0.0 [Memory Mapped Files]
Total database size in bytes: 0
After the db_dump, db_load and purge:
Calendar database version: 4.0.0
Sleepycat Software: Berkeley DB 4.2.52: (December 3, 2003)
Total database size in bytes: 1201864704
Total number of calendars: 14964
Total number of events: 830845
Total number of tasks: 17351
Total number of alarms: 55116
Total number of gse entries: 9
Total number of master component entries: 24100
Total number of deletelog entries: 1779967
Total logfile size in bytes: 5251612
Session database version: 3.0.0 [BerkeleyDB]
Total database size in bytes: 0
Total logfile size in bytes: 0
Counter database version: 1.0.0 [Memory Mapped Files]
Total database size in bytes: 0
Thanks again.

Sounds like we talking about 'Event Invitations Notifications'. These are the notifications that gets sent when some one invite you to an event. Whether you receive the notification or not depends on your preference that is stored in ldap. This can be set using the Convergence by navigating through Options-> Calendar -> Notifcations (Check "Notify me via email of new invitations or invitation changes"). The actual ldap attributes that gets stored in user's entry is below.
icsExtendedUserPrefs: ceNotifyEnable=1
icsExtendedUserPrefs: ceNotifyEmail=[email protected]
In the following cases, the user (attendee) will not get notifications even if the above preference is set.
a> Creating an event with attendees in the past. CS6, by default, suppresses notifications for past events. You can enable notifications for past events by setting the config "ine.pastnotification.enable" to "yes" in ics.conf
b> If the client creating the event requests server not to send notifications. (smtpNotify wcap param for storeevents.wcap). Outlook Connector uses this wcap param, so you won't get server notifications for the events invited using Outlook Connector. Outlook Connector sends it's own notifications directly.
I think, you are looking for these kind of notifications. The process responsible for sending these notifications is "csadmind" on the Frontend. So, you need to check admin.log on the Frontend to see if it is sending notifications or not.
Edited by: dabrain on Feb 21, 2012 9:26 AM

Snow Leopard client for NetRestore image not being recognized in Mountain Lion Server

I target firewired a MacBook Pro running Snow Leopard and ran System Imaging Utility and the machine does not show up as an option. Does Mountain Lion Server support Snow Leopard NetRestore images or am I doing something wrong?

I'm actually trying to figure that out as well. We have 10.5, 10.6, 10.7, and 10.8 Images we wanted to put together for our netrestore images on our server, but can only do 10.8 images currently.
We also have the AppleCare Helpdesk diagnostic kit which includes hardware tests, we were only able to get the newer mid-2012 and late-2012 Diagnostic utilities to netboot but none of the older ones.
So do we need a server running the older OS to get these or is there a better alternative? i mean really shouldnt be a problem considering theyre running inside of an image and dont rely heavily on the server resources other than to say "Yep, goto this file/directory".
I'd like to know more as well....

Question on not being able to update SQL Server

Hi Gurus,
The following code is working OK to insert a Date/Time format data on MS Access.
I ported the database over to SQL Server with the same DateTime type of data in SQL Server. Could anybody think of a reason why this could not work and a possible solution.
I am setting the parameters for a SQL query to update the database, and the 17th parameter is the datetime field in SQL Server.
int cc = -1;
stmt.setDate(17, new java.sql.Date(k.getExpirationDate().getTime()));
cc = stmt.executeUpdate();
My email is [email protected] I appreciate your help.
Thanks
Venkat

Thanks. I am trying that way, but have not been successful before now or till now.
Thanks for your suggestion.
Venkat

H323 cisco attributes not being forwarded to Radius accounting server

Similar Messages

Maybe you are looking for