Has anyone ever successful​ly done a cont double buffer acq from multiple SCXI channels AND a spare AI of the MIO that controls the SCXI chassis at the same time?

I am trying do a sanity check before I order some hardware.
What I want to do is acquire from multiple channels in a SCXI chasis and as part of the same acquisition, also read from one of the "un-used" AI channels of the MIO card.
My concern is this:
All of the channels of the SCXI chassis get multiplexed down into a single channel of the MIO card that controls the SCXI chassis. This means that channel 0 has to do multiple A/D conversions to get a reading from all of the configured SCXI channels.
Meanwhile, the other AI channel of the MIO only has to do one to get it's reading. It seems that the on-boar
d clock of the MIO would have to run at two rates to be able to read all of my SCXI channels AND the other AI channel.
What I want to do:
I want to just configure a vitual channel for all of my SCXI channels AND one more for one "odd-ball" signal that is incompatable with all of the SCXI modules.
Then I just want to list all of my virtual channels when I configure and start my continuous double buffered acquisition.
I have successfully done all SCXI channels before, but I have never tried to use one of the un-used AI on the MIO at the same time. I have used the spare DIO lines previously, but that will not work in this app.
So...
If you have done this and it worked, I would greatly appreciate hearing about any special techniques that were used, etc.
Thank you for reading this question,
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Jeremy answered here
http://exchange.ni.com/servlet/ProcessRequest?RHIV​EID=101&RPAGEID=135&HOID=50650000000800000007C4000​0&UCATEGORY_0=_30_%24_12_&UCATEGORY_S=0
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Similar Messages

  • Has anyone ever successfully done a cont double buffer acq from multiple SCXI channels AND a spare AI of the MIO that controls the SCXI chassis at the same time?

    I am trying do a sanity check before I order some hardware.
    What I want to do is acquire from multiple channels in a SCXI chasis and as part of the same acquisition, also read from one of the "un-used" AI channels of the MIO card.
    My concern is this:
    All of the channels of the SCXI chassis get multiplexed down into a single channel of the MIO card that controls the SCXI chassis. This means that channel 0 has to do multiple A/D conversions to get a reading from all of the configured SCXI channels.
    Meanwhile, the other AI channel of the MIO only has to do one to get it's reading. It seems that the on-boar
    d clock of the MIO would have to run at two rates to be able to read all of my SCXI channels AND the other AI channel.
    What I want to do:
    I want to just configure a vitual channel for all of my SCXI channels AND one more for one "odd-ball" signal that is incompatable with all of the SCXI modules.
    Then I just want to list all of my virtual channels when I configure and start my continuous double buffered acquisition.
    I have successfully done all SCXI channels before, but I have never tried to use one of the un-used AI on the MIO at the same time. I have used the spare DIO lines previously, but that will not work in this app.
    So...
    If you have done this and it worked, I would greatly appreciate hearing about any special techniques that were used, etc.
    Thank you for reading this question,
    Ben
    Ben Rayner
    I am currently active on.. MainStream Preppers
    Rayner's Ridge is under construction

    Jeremy answered here
    http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=50650000000800000007C40000&UCATEGORY_0=_30_%24_12_&UCATEGORY_S=0
    Ben Rayner
    I am currently active on.. MainStream Preppers
    Rayner's Ridge is under construction

  • Has anyone ever SUCCESSFULLY gotten iTunes to back up library to disc?

    I've tried numerous times over different versions of iTunes, and I can NEVER get iTunes to back up my purchased library to disc.
    It offers to do it to DVD, to regular CD--- and nothing works. It spits the tray out, says to put in a blank CD and I do-- and it "checks Media" and never accomplishes anything. I'm starting to doubt the function even works and was put in there to make it look good.
    Has anyone ever successfully gotten the "Back Up Library to Disc" function to work?
    im running the latest version of iTunes.

    GOOD POINT. You cannot backup to an external hd. Who wants to use dvds OR cds for backup anyway? The whole reason for buying an ipod was to avoid these two optical disc nightmares and get with a hard disk management solution. itunes doesn't recognize external hard drives for backup. Ridiculous. Try using an ext hd as the itunes location for your music if you really want to see problems develop. Managing music instead of playing music has become my past time since I got into the ipod/ itunes mess. All I do is try to clean up it's messes. The software developers need to be accountable. Class action? No support, except forum, unless you want to pay.

  • Has anyone EVER successfully used BlackBerry Bold BlueTooth DUN w/ iBook ?

    Greetings all,
    I have spent days trying to get my iBook G4 running OS 10.4.11 to successfully connect to the internet via BlueTooth through my BB Bold's supposed dial-up networking capabilities. I have followed endless threads in multiple Mac, Black, Crack, and other forums and have watched countless video demonstrations. None of the info I have found has worked, probably because every source of info involved either a different BlackBerry model, a different Mac model, or a different OS version.
    I get the same Internet Connect error every time: "A modem error occurred. Please check your settings and try again."
    I have tried multiple dial-up isp's and multiple access numbers. I do not claim to be an expert, but I have worked as a network administrator, have set up multiple network devices, and have a pretty good understanding of internet and general network technologies and this is just driving me insane.
    If anyone actually knows how to accomplish this task, I would be eternally grateful for step-by-step instructions or even just some insight into how I might determine what type of "modem error" occurred!
    Please do not tell me to purchase an iPhone or a tethering plan. If those were viable options at the moment, I would not be wasting our time here. Thanks!

    Ditto on both points. Meanwhile I use the solution of a third party backup.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Has anyone ever figured out how to interact with PP events from LabVIEW?

    We would like to know how to interface a motor control system with a powerpoint file such that after each motor step is complete the next slide is shown and so on.
    Direct contact can be made via [email protected]
    Cheers Jim & Jon

    You can use PP or just put your graphs in a picture control, easyly passing from one step to the next. If you prefer using PP, you could use ActiveX, as is done to control Excel within LabVIEW.
    Good luck

  • Has anyone ever had the icons on the menu magnify?  My phone slipped onto the floor in my car and icons are now hugh.  Don't know how to fix it.

    Has anyone ever had the icons on the menu magnify?  My phone slipped onto the floor in my car and icons are now hugh.  Don't know how to fix it.

    Double tap the screen with 3 fingers.
    Stedman

  • Has anyone ever done a Pluggable Data Source (PDS) with BC4J

    Has anyone ever done a Pluggable Data Source (PDS) based on BC4J. We already have the data stored in a resultset and would like to be able to have Oracle Reports re-use it. Any ideas?
    tks,

    Hi Metthew
    BC4J pds is in the pipeline and will be soon out on the Oracle Reports plugin exchange.
    Thanks
    The Oracle Reports Team

  • Has anyone had success in getting Apple to correct Maps mistakes?

    On multiple occasions I've submitted a correction using the function within Maps to report errors, but nothing is ever done.  Has anyone ever had any success in getting Apple's attention and getting something fixed?  Or is the submitting a correction feature just a black hole?  I've had to tell friends with iPhones to always use Google Maps rather than Apple to navigate their way to my house because Maps has completely mislabeled the street outside my development.  It sure would be nice if they had a human being you could call...

    For users who's printer/scanner does not have a compatible driver from their manufacturer:
    How do I scan or print with the driver from Apple Software Update?
    Depending on your printer and the type of driver update, you might need to scan in a different way than you did before you installed Mountain Lion.
    Scan from the Print & Scan window:
    Place the item that you want to scan on the scanner glass, or load it into the automatic document feeder (ADF) if your printer has one.
    Click the Apple menu (# ), and then click System Preferences .
    Click Print & Scan (# ).
    Click your printer in the left pane.
    Click the Scan tab, and then click Open Scanner .
    Click Show Details . The details of the scan display, including options to change scan settings.Figure 5: Show Details scanning screen# Image: Show Details scanning screen
    Change any settings as necessary, and then click Scan .
    NOTE:
    Make sure to select either the Flatbed mode or the Document Feedermode, depending on your printer and how you plan to scan.
    Hope this helps

  • Has anyone been successful importing h.264 into Encore?

    First, my system and goal:
    A MacPro with 2.66mHz dual core and 12 gigs of RAM.
    Multi Terrabytes of space.
    I shoot on a Panasonic HVX-200, edit in Final Cut Pro and output Quicktime files as the basis for rendering to DVD and Blu-ray. I shot this stuff in 1080i. The camera codec is DVCPROHD and that is what I output to also.
    I am trying to burn Blu-ray discs. I have an external Pioneer BDR-203 Blu-ray burner and it works fine.
    I have done my tests and have decided that for Blu-ray, h.264 is far superior to mpeg2 in look and file size so I am sticking with it.
    Here is the issue (and I have scoured this forum area and found no one discussing or solving this issue to date):
    I have made hundreds of different DVDs with DVDStudioPro and am very familiar with it. Not to get off on a tangent but my beloved Apple has decided to betray me by not supporting Blu-ray (the ONLY way to output HD for us independents) so I studied up on Encore and have been using it to format my latest project to HD. The interface works pretty nice and even has some superiority to DVDSP but you have to have the patience of JOB to see your results. 5 Day (Remember. That's 24 Hour Days) Rendering is my tops so far. (OK. Full Disclosure... the documentary is 3 hours and 15 minutes long BUT DVDStudioPro took the same Quicktime files and crunched them down to mpeg2 for the DVD in about a day) Anyway about 6 days ago I had a 3 day render session that crapped out on me as it was finally recording to disc. For some reason it didn't like the BD-RE disc I had in the machine and just bagged the whole process. When I put in a new disc it just started rendering All Over Again. After that debacle I gave up on that method and now am rendering to BDMV folders which I then burn to disc using Toast. (While I am writing this my fingers are crossed that it will make it to the end - it's been another 3 days...)
    I provide the details above to show why I am more than dismayed that I cannot figure any way to import h.264 files INTO Encore from another renderer. Either Compressor or Encoder render much faster than Encore. So I have tried render my project to a variety of output types from both Apple's Compressor and Adobe's Encoder with no joy any way I try.
    (as a side note I am also dismayed that when I made a change to a MENU, Encore decided to encode The Whole Project Again rather than just the menu part...)
    One of my latest file testing adventures was based on a theory that the problem has to do with DVCPROHD recording to 1280 x 1080 anamorphic rather than 1440 x 1080 (the "expected" frame size for 1080i). I fooled with that a half day but could not get either renderer to generate any test material from my FCP output that Encore would burn without re-rendering. By that I mean I cajoled and tricked Compressor and Encoder to output 1920 x 1080 files; 1440 x 1080 files and 1280 x 1080 files (all h.264) to see if Encore would recognize any of them without re-rendering them. No Luck.
    So. Has anyone had success importing h.264 into CS4Encore from anywhere (but particularly using the same or similar gear I am using)? The Encore literature really doesn't give you much to go oon.
    Lately I am very inclined to think the problem has something to do with this 1280 x 1080 DVCPROHD issue but I can't say for sure. I offer that as a suggestion if anyone else with a similar production stream is having the same problem and maybe it will trip a switch in their mind for a solution.
    I like the Encore interface and design possibilities you have by swinging back and forth from PShop and After Effects but using Encore's renderer is like Chinese Water Torture.
    Thanks for your help.

    Brian,
    I got your test file into Encore and got Encore to show its Blu-ray transcode status as "Don't Transcode".
    Screenshots:
    PrCS4 Export settings:
    EnCS4 Project Panel:
    Since it's hard to make out the En Project panel, I'll attach the same image to another message.
    -Jeff

  • Has anyone ever seen this error

    We just launched a vaccation tracking app with a coldfusion
    front end and an access 97 backend (dont ask). The app was tested
    for over a month and passed all tests. However we never tested for
    volume, or amount of users hitting the app. On the backend, we have
    an access table linked to a text file. Again, this tested out
    perfectly over the past month. This morning after release to the
    entire company of about 2,000 people, users began reporting this
    error:
    The text file specification 'EmployeeList Link
    Specification6' does not exist. You cannot import, export, or link
    using the specification.
    Some users logged in to the app successfully and some
    recieved this error. For those that recieved the error, we had them
    back out and re-login and then the app worked just fine.
    Has anyone ever seen this or have a guess as to what is going
    on?

    Hi,
    The right way would be to use a "real" database server.
    But you can test if db-caching can improve the issue.
    With each <cfquery> you can set a cachedwithin
    parameter. Using that should allow you to query the Access db once,
    and then have CF keep the query results in memory (for the DB as
    well as the text-file).
    You could query the complete database with no filtering this
    way, and then filter the data using QueryofQuery to output only
    records for specific users/groups/regions.
    You also need to make sure the settings in CF admin are
    configured right for this.
    The more often the database content is updated, the slower
    this solution will get though.
    cheers,
    fober
    ps. for the cachedwithin parameter in the query set a
    timeframe of forever, so the recordset never gets updated, and then
    actually execute a new query to update the recordset at the end of
    your "save a vacation" or "updated a vacation" functions. This way
    the app would only read the db when a real change to the records
    occurred.
    But like I said with 2000 users, even that may not be enough
    to get the app performing.

  • Has anyone ever ran Logic using VMWare Workstation on a Windows PC?

    Has anyone ever emulated Mac OS X and used Logic on their x86 Microsoft Windows systems? I was thinking about doing this to use some synths and stuff with some Windows designed software. I'm not sure if it is possible to use both operating systems at the same time with VMWare Workstation operating system emulator. Help me out guys. Has anyone ever done it? Can it be done?

    VMWare Workstation will not run the client version of Mac OS X in emulation, and likely won't run Mac OS X Server either.
    (32050)

  • Has anyone ever succeeded to use the scope_identity() from the LabVIEW DB toolkit ?

    Hi,
    Using LabVIEW 2014 DS, and MSSQL 2008R2.
    I have configured a table with identity, so the indexed will be incremented automatically.
    I am trying to get the ID of the last Insert command that I am using.
    I am trying to SELECT SCOPE_IDENTITY() but with no success.
    I read about trying to so it with a procedure or transaction, but I just could not succeed myself.
    Has anyone ever succeeded to use the scope_identity() from the LabVIEW DB toolkit ?
    If yes, can you please elaborate more or even share the code ?
    Thanks, 
    Amitai.

    Yes I have...let me dig out some code...
    I do my INSERT query (with a semicolon at the end) and in the same query string do a "SELECT SCOPE_IDENTITY() as inserted_id;" - essentially what you're doing here is running two queries in one - one to insert your data and the second to retrieve the ID. From what I remember of when I did this (last year?), I think scope_identity() is valid for the same connection so as you're doing both queries in the same connection it should always be valid.
    I then do this to get the ID (pardon the crappy VI snippet):
    Essentially I execute the query and the result is a 2D array that contains one row/column which is your last inserted ID.
    Certified LabVIEW Architect, Certified TestStand Developer
    NI Days (and A&DF): 2010, 2011, 2013, 2014
    NI Week: 2012, 2014
    Knowledgeable in all things Giant Tetris and WebSockets

  • Has anyone ever been quoted more than $500 to replace a failed logic board?

    Has anyone ever been quoted more than $500 to replace a failed logic board? A Genius buddy of mine swears that it'll never be over $500 but I' convinced he's high out of his mind.

    I doubt it. They don't even take the same kind of RAM.
    What makes you think a replacement "will most likely go bad in the future"? Some have had to go back more than once; many haven't. (And many have not gone in at all.) There are many iBook users out there, happily iBooking away without any knowledge of the iBook Logic Board Repair Extension Program because they've never had a problem.
    Get it replaced, free, NOW, and worry about the future when it gets here.
    http://www.apple.com/support/ibook/faq/
    P.S. When you make an error in a post, there is a little edit-pencil icon next to the "Reply" icon in your post. The edit pencil stays there for about 15 minutes to allow you to edit your post. Just click on it, and it takes you back to your message box so you can edit it to your heart's content.

  • Has anyone ever changed an apple id on the iphone

    my wife and i have been sharing an apple id and i now want to provide her with her own.  since the icloud has been launched any app she downloads i get and vice versa.  Has anyone ever switched out an applie id on the iphone before.  does it have to be synced with itunes once to make the change happen?  If so will i still be able to keep all of the contents ih her phone.

    You can share iTunes content within the same household, so if you get your own Apple ID/iTunes account, you can continue to use content obtained using your Wife's account. Any app updates to apps obtained using the wife's Id must be done using that ID. Just authorize the computer for the new Apple ID/iTunes account: Store>Authorize this Computer. You can switch iTunes accounts on the phone by going to: Settings>Store...tap the ID shown...sign out...sign back in with the ID you want to use.

  • Has anyone had success using SharePoint and FrameMaker 10 together using CMS?

    Has anyone had success using SharePoint and FrameMaker 10 together using CMS?

    Thanks for reminding to at least update the results thus far.
    Update 4:
    I did get quite a bit of support initially although slowly over a period of a month or so. After Adobe FM support and my SharePoint systems engineer reviewed how FM10 was setup on my computer (which I am the admin for our department’s SP site) and how it interfaces with our SharePoint 2010 Enterprise Edition, there was two conclusions:
    Basically Adobe FM Support said that FM10 did not support claims-based authentication and they can no longer help me. They said it will work with FM11 when it comes out.
    My SP Systems Engineer, said that FM10 is connecting to SP 2010 just fine but that the FM10 has a software glitch that causes FM10 lose control when executing checkout procedure within FM10. I can checkout and edit that same file in SP with no problems.
    About a month later, I upgraded to FM11 and ran into the same problem. I attempted to get Adobe FM Support to help and they said they will look into and get back to me. That was in July and I have not heard anything more from them, and to be honest, my schedule has been extremely busy the last 5 months that I have not had time to pursue it any further.
    Needless to say, I was very disappointed with the SP interface and, overall, the lackluster support I received from Adobe. Having a working SP interface was one of the criteria for purchasing TCS3.5 (and subsequent upgrade) in the first place.
    One thing of note, we migrated from SP 2007 to SP 2010 in February 2011 and, at the time of Adobe support, I still had access to my SP 2007 site. FM10 and FM11 had to no issues working with SP2007. Unfortunately, SP 2007 is not an option for me anymore.
    Also, another observation of FM10/11 not working with SP 2010, it seems that FM10/11 is automatically configured to work with SharePoint Drafts folder locally when connecting to the SharePoint library. This worked just fine with SP 2007 but SP 2010 does not use SharePoint Drafts folder locally the same way (the programming changed, don’t recall where I saw it, probably when searching this issue online)  and I suspect that is one of the main issues why it does not work correctly.
    So at this time, I have not found a working solution to this problem.

Maybe you are looking for