Help with a new RV082 Router

Greetings all,
I hope this is the correct place to post my request for help.
I just installed a new RV082 Router and I can access the internet without any problems.
We have a security camera at 192.168.1.28 on the LAN side. This works just fine on the LAN side but cannot be accessed from remote machines trying to log into the camera remotely.
The camera can be access on port 2782 without any problems using my Linux based Smoothwall router by going to any web browser such as Firefox or IE8 by keying in: http://xxx.xxx.xxx.xx:2782 and the camera’s web interface comes up allowing a user to login by keying in their id and password.
I’ve tried for a few hours now to change firewall setting but I still can’t get this to allow anyone to login remotely.
The Smoothwall router allows me to setup a pass through in the firewall by creating the follow entry:
Protocol                                  TCP
External Source IP                ALL
Source Port                           2782
Destination IP                        192.168.1.28
Destination Port                    2782
This works without any problems.
Can anyone help be configure the RV082 in order to gain access to the camera?
Any help will be appreciated. This is now driving me crazy.
Thanks

Hi Howard,
To forward the port in the RV082, go to Setup-> Forwarding. Click the Service Management and create a new service for port 2782 (i.e. Service Name IPCam, Protocol TCP, Port Range 2782 to 2782, Add to list, Save Setting) Go back to Forwarding and select the new Service from the drop down list. Enter the IP address of the camera and check the Enable box. Add to list and Save Settings at the bottom of the page. Please let us know if this works or if you need further assistance.

Similar Messages

Need a little Help with my new xfi titanium

+Need a little Help with my new xfi titanium< A few questions here.
st question? Im using opt out port on the xfi ti. card and using digital li've on a windows 7 64 bit system,? I would like to know why when i use 5. or 7. and i check to make sure each speakear is working the rear speakers wont sound off but the sr and sl will in replace of the rear speakers. I did a test tone on my sony amp and the speaker are wired correctly becasue the rear speakers and the surrond? left and right sound off when they suppose too. Also when i try to click on? the sl and sr in the sound blaster control panel they dont work but if i click on the rear speakers in the control panel the sl and sr sound off. Do anyone know how i can fix this? So i would like to know why my sl and sr act like rears when they are not?
2nd question? How do i control the volume from my keyboard or from windows period when using opt out i was able to do so with my on board? sound max audio using spidf? Now i can only control the audio using the sony receiver.
Thank you for any help..

/Re: Need a little Help with my new xfi titanium? ?
ZDragon wrote:
I'm unsure about the first question. Do you even have a 7. system and receiver? If you just have 5., you should be able to remap the audio in the THX console.
I do have a sony 7. reciever str de-995 its an older one but its only for my cpu. At first i didnt even have THX installed because it didnt come with the driver package for some reason until i downloaded the daniel_k support drivers and installed it. But it doesnt help in anyway.
I have checked every where regarding the first question and alot of people are having problems getting sound out of there rear channels and the sound being re-mapped to the surround right and the surround left as if there rear left and rear right.
I read somewhere that the daniel_k support drivers would fix this but it didnt for me and many others.
For the second question i assumed it would be becasue of the spidf pass through and that my onboard sound card was inferior to the xfi titaniums. But i wasnt sure and i was hopeing that someone would have a solution for that problem because i miss controlling the volume with my keyboard.

TS4062 Syncing with a new network/router

I am having trouble on syncing on a new WIFI network.
I moved and I have a new router with a new network name. Since that I cannot sync over wifi.
On syncing options on the ipod says that I will be able to sync via wifi when "old network" is available.
I cannot change network name to the old one cause new network name is setup by ISP.
Hope it is clear enough and someone can help me.
Thanks.

Do you have a Google account? I find Google the easiest to use for contact syncing, as it's platform and device independent. You just set up your Google account as an exchange account on all of your devices and the contacts and calendars are there. Easy peasy.
If not, I'm sure someone with more experience of iCloud will be along soon.

Hello everyone, hoping for some help with my new Apple Cinema Display 20"

Hi everyone, I bought an Apple Cinema Display 20 inch LCD monitor, just about 3 weeks ago. I have two issues I am hoping to get some help with.
1) I am using the screen on a PC with Windows XP, and I was very disappointed at the lack of PC support. I have no on screen display (OSD), so I can't see what percentage I have my brightness set to, and I can't alter the colour or contrast of the display, etc. Luckily it defaulted to very good settings, but I would really like to be able to use the (fan made?) program called "WinACD". If I would be best asking somewhere else, please direct me there. If not, my problem is that I installed it added the "Controls" tab, but it just says, Virtual Control Panel "None Present". I have tried googling for an answer, and I have seen many suggestions, but none of them worked. I installed the WinACD driver without my USB lead plugged in, and someone said that was important. So I have tried uninstalling, rebooting, then reinstalling it again with the USB plugged in, and a device plugged in to my monitor to be sure. It didn't seem to help. I have actually done this process a few times, just to be sure. So I would really like to get that working if possible.
2) I am disappointed at the uniformity of the colour on the display. I have seen other people mention this (again, after a google search), and that someone seemed to think it is just an issue we have to deal with, with this generation of LCD monitors. Before I bought this screen, I had an NEC (20wgx2), and it had a very similar issue. Most of the time, you cannot see any problem at all, but if you display an entire screen with a dark (none prime) colour, like a dark blue green colour, you can see areas where it is slightly darker than others. It was more defined on the NEC screen, and that is why I returned it. I now bought this Apple Cinema Display, because it was the only good alternative to the NEC. (It has an 8bit S-IPS / AS-IPS panel, which was important to me). But the problem exists in this screen too. It isn't as bad thankfully, but it still exists... I have actually tried a third monitor just to be sure, and the problem existed very slightly in that one, so I think I am probably quite sensitive in that I can detect it.
It is most noticable to me, because I do everything on this PC. I work, I watch films, and I play games. 99% of the time, I cannot see this problem. But in some games (especially one)... the problem is quite noticeable. When you pan the view around, my eyes are drawn to the slight areas on my screen which are darker, and it ruins my enjoyment. To confirm it wasn't just the game, like I said, I can use a program to make the entire screen display one solid colour, and if you pick the right type of colour (anything that isn't a bright primary colour), I can see the problem - albeit fairly faintly.
I am pretty positive that it is not my graphics card or any other component of my PC, by the way, because everything is brand new and working perfectly, and the graphics card specifically, I have upgraded and yet the problem remains - even on the new card. Also, the areas that are darker, are different on this screen than on the other screens I have used.
So basically, I would like to register my disappointment at the lack of perfect uniformity on a screen which cost me £400 (over double what most 20 inch LCD screens cost), and I would like to know if anybody could possibly suggest a way to fix it?
It is upsetting, becuase although this problem exists on other screens too, this is, as far as I know, the most expensive 20" LCD monitor available today, and uses the best technology available too.
p.s. If anyone would like to use the program that lets you set your entire PC screen a specific colour, it is called "Dead Pixel Buddy", and it is a free piece of software, made by somebody to check for dead pixels. But I found it useful for other things too, including looking at how uniform the colour of the screen is. That's not to say I was specifically looking for this problem by the way... the problem cought my eye.
Thanks in advance!
Message was edited by: telelove

I've been talking about this on another forum too, and I made some pictures in photoshop to describe the problem. Here is what I posted on the other forum:
Yes, "brightness uniformity" definitely seems to be the best description of my issue.
Basically it just seems like there are very faint lines down the screen, that are slightly darker than the other areas on the screen. They aren't defined lines, and they aren't in a pattern. It's just slight areas that are darker, and the areas seem like narrow bands/lines. Usually you can't see it, but in some cases, it is quite noticeable. It is mainly when I'm playing a game. The slightly darker areas are not visible, and then when the image moves (because I am turning in a car, or turning a plane, or turning in a shooter etc.) the image moves, but these slightly darker areas stay still, and that makes them really stand out.
As for how it looks, I tried to make an example in photoshop:
Original Image:
http://img340.imageshack.us/img340/3045/td1ja9.jpg
Then imagine turning the car around a bend, and then it looks like this:
http://img266.imageshack.us/img266/959/td2hq7.jpg
It's those lines in the clouds. If you can tab between the two images, you can see the difference easily. Imagine seeing those lines appear, every single time you move in a game. (I haven't tested this in movies yet, but I am assuming it's the same).
It isn't very clear on a static image. But when the image moves, the darker areas stay in the same place and it draws your eyes towards them. It isn't terrible, but it is annoying, especially consider how much this screen cost.
Message was edited by: telelove

Please help with a new dual purpose PC build

Hi everybody in AdobeLand!
I've been reading various boards and hardware sites and have started piecing together a dual purpose computer system. It will be used for both video editing (of pre-shot hacked, high bitrate I-Frame Panasonic GH2 DSLR and camcorder footage using the AVCHD codec @ 1080p 24 and 30 fps) and webcasting/streaming purposes. I would build two computers for each task, but it's just not in the budget right now. I'm already stretching things as is.
I'm still not sure if I will be using Adobe Premiere or Sony Vegas Pro 12 yet, though it seems like they organize their folders and file structures about the same. Adobe's cloud service has me a bit scared off right now. This new scheme feels like they have their hand purpetually in your wallet, which does not sit well with me. I may still go with Vegas 12 just to avoid that hassle right now. Help guide me here, experts! Telestream's Wirecast is being used for multi-cam switching and graphics for live and pre-recorded material being compressed and streamed.
Back on topic:
Here's the build as of right now...
OS: Windows 7 64-Bit Professional (Windows 8 absolutely sucks!)
CPU: Intel i7-4930k 6-Core Ivy Bridge (own)
Motherboard: Asus P9X79 Pro (own)
Memory: Crucial Ballistix 1.35v Sport DDR3L @ 32 GB (own)
GPU: EVGA GTX 770 FTW w/ 4 GB (will buy another HD monitor at a later date, hence the 4GB memory)
Case: Fractal Design XL R2 Full Tower
CPU Cooling: Noctua NH-D14 w/ SE2011 Bracket
PSU: Corsair RM1000 Quiet Series / 80 Plus Gold / 1000 Watts
Monitor: Dell U2412M Ultrasharp 24 inch / 1920x1200
Optical Drive: LG Blu-ray Writer
Keyboard: Microsoft 4000 Ergonomic
HDMI capture cards: Blackmagic Designs Decklink Mini (x2)
Storage:
I bought two Samsung 840 Pro SSD drives: one 128 GB and one 256 GB
Thinking about possibly 2 (maybe 3-4 if I really stretch) Seagate ST3000DM001 3TB HDD's.
I could sure use your help with any advise on arranging the storage to get the best bang vs. buck in speed and storage utilization (Wirecast can be setup to record live webcast sessions at 720p or 1080p in compressed files... probably no more than 120 minute webcasts... so that comes into play as well). Just don't have the funds for an uber-expensive RAID controller card right now.
Any opinions overall on the parts for the current build? I still have time to send back and exchange anything already purchased.
Thank you for your time and consideration.

What do you not understand from:
With all the reading and writing going on, on the boot disk, it is understandable you need a (number of) dedicated disk(s) for video editing, especially with the bandwidths required when the clip duration is short and the number of tracks exceeds one and uses a codec more complex than DV. The kind of files used during editing are, in order of their need for speed:
Media cache & Media cache database files, created on importing media into a project. They contain indexed, conformed audio and peak files for waveform display.
Typically small files, but lots of them, so in the end they still occupy lots of disk space.
Preview (rendered) files, created when the time-line is rendered for preview purposes, the red bar turned to green. Read all the time when previewing the time-line.
Project files, including project auto-save files, that are constantly being read and saved as auto-save files and written when saving your edits.
Media files, the original video material ingested from tape or card based cameras. Typically long files, only used for reading, since PR is a non-destructive editor.
Export files, created when the time-line is exported to its final delivery format. These files are typically only written once and often vary in size from several hundred KB to tens of GB.
When you are doubting which category of files to put on which kind of disk, especially when using both SSD's and HDD's, keep in mind that the speed advantage of SSD's over HDD's is most noteworthy with the Media cache & Media cache database. These files are frequently accessed, are small and there are many, so reducing latency and seek times and increasing transfer rates pays off by putting these on a SSD, rather than on a HDD, even if it is a raid0. Export files can go to the slowest volume on your system, since you only export once. To help you decide, I have added priority rank-numbers for speed, with 1 for the fastest volume and 5 for the least speed-demanding category.
and
Well, in the benchmark tests we have not seen any noticeable difference between SSD and HDD in terms of performance, but logic dictates that there should be a small difference in performance when the volume used for media cache is a SSD, because of the much faster access time and lower latency compared to a conventional disk. If it is noticeable, it is specifically on this volume with the media cache and media cache database, due to the large amount of small files that need to be accessed and written. This argument does not apply to the media volume with a limited number of files, that are very big in size.

Need some Help with the new Genius Mixes on iTunes 9

I would like to know how to use the New Genius Mixes on iTunes 9. I don't quit know how to use it yet and like all of us we're all just learning how to use the Genius Mixes. I did watch the KeyNote but they didn't go into great detail on how to use it. Does Apple have a web site that has more detail instruction on how to use the genius Mixes? I did find some info. on how to use the Genius mixes but it didn't go into great detail on how or what to do with the genius Mixex and thats what I need.
when I click on the genius Mixes icon under the "Genius", what shows up is a Big square with four album images of my music that I have in my music collection, I go and roll my mouse over the Big square with my four music albums and click on it to play the music and it'll play what ever I have in the Genius Mix list plus as I roll my mouse over the Big Square, under it it says "Jazz Mix" with some text writings under the Jazz mix.
I want to change the Jazz mix Title and I want to know how to add more music square boxes to my Genius Mixes just like they show in the Keynote and I would like to edit and create my own four square music boxes in my Genius Mixes.
I never used my music genius list, I always created just a play List, now I am just learning how to use this music Genius lists and I don't know how to use it at all and I need someone that knows how to use thr Genius Mixes list to help me how to use it since there isn't a how to book yet for the new iTunes 9.
Can someone Please help me with the new genius Mixes on iTunes.
Thank you,
Mrs Trisha Foster

Today, I was getting an array out of bounds exception on a split
I don't see how that could happen with the 'split' method since it creates its own array.
For this particular string, ordSplit.length = 24 and commas = 26.
PERFECT! That is exactly what it should be!
Look closely at the end of the sample string you posted and you will see that it has trailing empty strings at the end: '1096200000000242505,,,'
Then if you read the Javadocs for the 'split' method you will find that those will NOT be included in the resulting array:
http://docs.oracle.com/javase/6/docs/api/java/lang/String.html#split(java.lang.String)
split
public String[] split(String regex)
Splits this string around matches of the given regular expression. This method works as if by invoking the two-argument split method with the given expression and a limit argument of zero. Trailing empty strings are therefore not included in the resulting array.
Just a hunch but your 'out of bounds exception' is likely due to your code assuming that there will be 26 entries in the array and there are really only 24.

HELP with the new version of skype

Hi thank you for looking at this and spending you time please exuse my spelling and grammer I need help with my skype about the new verson i downloaded it today then boom when it said done downloading my skype was on a loading thing for my online status then i said "oh let me try to unlog then relog then it keeps giveing me this error message "Skype cant connect!" my internet works fine and no my proixy and crap like that is not messed up i have been searching the fourm for abunch of answers none of them worked please help!

ruwim wrote:
What Firewall and Antivirus applications are installed on your computer? Be aware that even expired applications may still block Skype.
I disabled my firewall and i have a Antivirus that didnt bug it before after i updated it then it stoped working

I need help with my new LG G2. I dial *611 but it will not recognize my phone number

I am having trouble setting up my new LG G2. When I dial *611, it will not recognize my number, and the 800 number refers me back to the *611 number. There is no live chat available on the website, so I am lost. Is this any way to run customer support?

It seems I am about the only G2 customer support you'll fund unfortunately. Chat is available on the support site after logging in to My Verizon on the web, but you have to click on Contact Us at the top right of the page then choose Live Chat and then Help with My device and then look to the right and wait for the red dot to turn green. *611 will take you to a screen where you can launch My Verizon or Click to Call which dials the customer support number. Unfortunately chat is about as useless as waiting for a rep to respond in the forums. Calling is the only way to get started and work your way up the chain. Going to a store is a hassle. What exactly is the problem you're having? You can't activate the phone or set up your Google accounts or what?

Help with downloading new version of flash player not accepting password

I am having trouble downloading the new flash player version. Adobe is not excepting my password even with changing it several times. Need help with downloading the new version.

It's NOT an Adobe password. It's your Operating System (admin) password.
Download the Adobe Flash Player installer directly by clicking one of the following links.
Flash Player for ActiveX (Internet Explorer)
Flash Player Plug-in (All other browsers)
Flash Player (Mac OS X)

Help with Aiport Dual Band Router

Can someone help me, i have my router set basically default settings with security set. For some reason i cannot get any push notifications from any messaging app on my ipad. Now on a netgear router i can get it to work with no problem. I hope someone can help or suggest settings, Ive been searching and post on different forms with no luck. even apple support was a dead end. Thanks
Rich

Could you provide what settings that were successful with the Netgear router that allowed you to do this and I will help figure out what would be the equivalent settings for the 802.11n AirPort Extreme Base Station (AEBSn). Are these notifications coming from the Internet and require specific ports to be opened?

Help with installing new graphics card

Hi I have a 3 year old hpe575a (hp pavillion)
Intel i7 2600, 8gb ram
Orginally had a ati hd radeon 2gb (not sure what model)
in it
after 2 years the radeon finally melted ( always had overheating problems in the australian summer )
so I bought a nvidia gtx630m which had the same connections and power requirements and connections as the radeon
I csnt seem to get it working, despite the card powering up, and loading the splash screen it doesnt go any further, I can get to the network boot screen or the hp splash screen but no further, and I cant find any bios updates for my mptherboard (pegatron) so do I need a new motherboard? The computer works 100% fine without the new graphics card
Should I get a new motherboard. Or graphics card? which would be cheaper? or is there someway to get the current system to work with the new graphics card? thanks -zac

Hi,
The existing card is an "AMD Radeon HD6570 (2 GB)". I don't know how you can fit a Nvidia GTX630M to your machine because this card is for laptop:
     http://www.geforce.com/hardware/notebook-gpus/geforce-gt-630m/specifications
Probably you are talking about the following card:
    http://www.geforce.com/hardware/desktop-gpus/geforce-gt-630/specifications
The card should be able to use 300W PSU on your machine (no need new PSU). My suggestion:
(a) Update BIOS to the latest one, please check, should be "Version7.15 Rev. A" the motherboard is Cleveland
     http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=cp-101150-1&cc=us&dlc=en&lc=en...
(b) Install driver for new card
Hope this helps.
Note: Autumn now but still hot isn't it ?
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Help with my new curve please

I am hoping someone knows the answers to my questions! Thanks in advance if you can help.
Just got a new blackberry today as my other curve died today. Got a new curve.
I liked the way I could put more icons on the screen down the left side and then across the bottom. Can I do that with the new one? I also couldnt' figure out how to put an icon on the home screen . currently I have a couple emails, calendar and contaccts and I'd like the browser to be there. How do I do that?
Facebook. I downloaded the free app but now can't really find where it is andhow to get it to be an icon on my home screen. when I go to download it , it says i've already downloaded it.
thank you!

Couple of things to do carriemn.
1. Look here for the steps to change themes on your device (see if the Dimension L is listed): 9330 User Guide
If not there, you can also google something like "Blackberry OS 5 Dimension L theme" and see what you get back. There are lots of websites that have free or paid themes that you can download. Just be sure that it is a theme written for OS 5 since that is what you are running on your device.
2. Try looking in all the folders on your homescreen for Facebook. It may be there and you haven't found it yet. If not, try a battery pull. Pull the battery out with the device ON. Wait about a minute and put the battery back in. Let the BB completely restart and see if that doesn't help. Clears out the memory and refreshes the BB; like rebooting your pc. See if Facebook icon is there after the restart.
When you have anomalous behavior in your BB a battery pull often helps to clear it up too.
Write good notes as you go so you can refer back to them if necessary. Let us know how it goes.
IrwinII
Please remember to "Accept as Solution" the post which solved your thread. If I or someone else have helped you, please tell us you "Like" what we had to say at the bottom right of the post.

Help with Connecting New Computer w/ WRT110

My sister just got a new laptop and has the WRT110. My brother in law passed away 3 weeks ago and he had the security passcodes. I just called Linksys to get help with it and their warrenty is up and wanted to charge us $30. Money is tight right now. Is there anyone that can help us with this issue?
Thanks so much

Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
Click on the Wireless tab..under Wireless tab,click on the subtab Wireless Security...Now,check the Security/Network Key.If you are using WEP Security then,use Key1 as the Security/Network Key.

Help with my new u410 touch

Hi, well first of all I'm very happy with my new laptop, saddly I don't noticed that I bought it with 4gb of RAM. According to many people, if I add more RAM it will void my warranty, is there anyway I can avoid that from happening? My laptop haves 24gb of ssd and I am curious if I can upgrade it and if you recommend it.
Another question but I think this one is pretty stupid, but anyways... Is the NVIDIA 710m soldered to the motherboard or can it be upgradeable?
Thanks a lot for your help, I worked very hard and this is my first laptop .

supahdog wrote:
Hi, well first of all I'm very happy with my new laptop, saddly I don't noticed that I bought it with 4gb of RAM. According to many people, if I add more RAM it will void my warranty, is there anyway I can avoid that from happening? My laptop haves 24gb of ssd and I am curious if I can upgrade it and if you recommend it.
Another question but I think this one is pretty stupid, but anyways... Is the NVIDIA 710m soldered to the motherboard or can it be upgradeable?
Thanks a lot for your help, I worked very hard and this is my first laptop .
The ssd is used for caching. Advising you to temporarily defer the upgrade until such time that you have all the info needed to do it.
The ram is different. To add more ram refer to page 72 of the hardware maintenance manual of your unit.
Pertaining to the GPU, it is soldered on the board. It is non-upgradable.

Help with Footers (New Update Glitch)

Hi there,
I'm in need of some urgent help with my website as upon publishing with the new update installed all my footers have changed.
I now have massive gaps between where my content ends and the footer begins on almost every page. Example.
Pages which are attached to the Master pages are not reading the same footer positions now. For example, my home page footer begins at nearly 1300 but the master it's attached to it should be closer to 950..... Everything was fine until the update today.
Any help would be appreciated. Thanks!

Maybe I can explain this a little better, issue is still going on, spoke with an Adobe representative but didn't get any helpful advice, actually got no advice other than to send the file in.
So here's my home page: you can see the gap between the content and the footer (with the footer starting at around 1300.
But then here's the Master page it's attached to, the footer is set to start way higher, this is happening on every one of my pages.

Help with a new RV082 Router

Similar Messages

Maybe you are looking for