Help with a wireless bridge

How do I get the airport extreme to broadcast to a U.S Robotics model 5430 wireless g bridge? I want to hook up the bridge to my directv box for on demand. THANKS!!!

It is possible that your US Robotics wireless bridge is having difficulty connecting to the AEBSn when the AEBSn is operating in the 802.11n radio mode. Again the default mode for the AEBSn is 802.11n (b/g-compatible). Since you are not running wireless encryption that issue would be a mute one. I was just checking because the bridge only supports the WEP standard for encryption.
I suggest that you reconfigure your AEBS for 802.11g only or 802.11b/g compatible radio mode to see if the bridge will connect to it now. Note: In order to access these non-"n" modes, you need to hold down the <Option> (Mac) or <Control> (PC) key before making the radio mode selection in the AirPort Utility.

Similar Messages

Connecting printer with a wireless bridge

I have an airport extreme base station. I am trying to connect a HP Photosmart 3200 printer. It has built in networking and I have a motorola wireless bridge to plug it into. What do I need to do? The tech at motorola said to see the range of the router ip addresses and to see if it was compatible with a DHCP wireless bridge. We did connect the bridge to my laptop and gave it the webkey. She wanted to assign it an IP address, but I wasn't sure it needed one. There is already a printer plugged into the USB and the printer does work with both my mac and wireless toshiba laptop when connected with a USB cable. TIA

You need to do two things.
Configure the Motorola Wireless Bridge to connect to your wireless network.
And then by connecting the printer to the bridge you need to configure the PhotoSmart 3200 to join your network.
iFelix

Configuring the WRVS4400N v2 to operate with a wireless bridge

I have a Motorola WRG850G wireless router setup as a wireless bridge (router functions disabled). The SSID, channel number & security options are set identical to the WRVS. I assigned it a static IP address of 192.168.10.148. My WRVS is 192.168.10.1. The DHCP addressing range is set to 192.168.10.100 through 192.168.10.149. I have not been able to get this bridge to connect to the WRSV. Any suggestions? Thanks

Thanks for the response. For configuration purposes, both devices are in the same room. Both devices are using the latest firmware. The security settings for both are WPA2, AES encryption with a passphrase. I read elsewhere about various successes and failures with wireless bridging and different security settings. Should this be a concern here due to the age difference between my WRVS4400N and my Motorola WR850G?

Help with my wireless network

On Friday it asked me for my password to my wireless network at my house, so I put it in. Then it said unable to join. I think I got the password wrong. Now when it asks me if I want to join it doesn't ask me for my password it just says unable to join. I can't talk on the phone and go online at the same time anymore. Can someone help with me this so I am able to put in my password for this? Thanks!

JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH, JO-SEPH,
HIP, HIP... HORAAY!!!! HIP, HIP... HORAAY!!!! HIP, HIP... HORAAY!!!! HIP, HIP... HORAAY!!!! HIP, HIP... HORAAY!!!! HIP, HIP... HORAAY!!!! HIP, HIP... HORAAY!!!! HIP, HIP... HORAAY!!!! HIP, HIP... HORAAY!!!!
IT WORKED!!! YOU'RE A GENIUS!!! Thank you! : )

Connectivity Issues with 1400 Wireless Bridge

Just seeing if anyone has run into a similar problem....I have two 1400 outdoor wireless bridges. They have been in place for a couple of years without issue. This past week, the non-root bridge began dropping it's association, at first randomly, then consistently. Both bridges have been replaced, antennas (AIR-ANT58G10SSA-N) on both have been replaced, and a spectrum analyzer has been used to verify there is not a problem over the air...the ditance between the two is >=1000 feet. Debugs show no reason for the drop, and when the two are asscoaited, the RSSI is averaging around -78. It had been down since Thursday, then last night, as another step in the process of elimination, we replaced the power injector on the root side, and the two bridges associated. They were up for two hours, then went down again, and then started going up and down randomly. As an additional step in the process of elimnation, we are now going to move the power source that the PI is connected to. Anyone ever run into something similar before or have any additional ideas? Thanks in advance.
Below is the most information I can glean from the logs
*Mar 1 06:31:39 pst: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0, Associated To AP KAirBridge_Para 0019.566e.be47 [None WPA PSK]
*Mar 1 06:31:39 pst: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 06:31:41 pst: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not valid
*Mar 1 06:31:41 pst: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 06:31:42 pst: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0, Associated To AP KAirBridge_Para 0019.566e.be47 [None WPA PSK]
*Mar 1 06:31:42 pst: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 06:32:05 pst: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not valid
*Mar 1 06:32:05 pst: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down

Yeah, power save is off, the cable run is only about 20 feet. The radio interface was shut down last night so that alerts weren't generated through the night due to flapping, I opened the interface earlier and right now both are up and have been for about an hour. I agree, -78 is not a great signal...currently, looking at the association, the root is at -64 and the non-root is at -62...will update if there is a status change. Thanks.

Help with wired/wireless solution

Ok.. I just purchased a G5 2.7 .. my old Mac is an iMac G4 1.25.
Both computer are in the same room, and I need both to have internet access.
Based on what I've read in the forums, it would be better to have a wired internet connection for speed, but I have an Airport Card and Airport Express I can use.
I would like to have have the G5 wired, as this would be my main computer, and perhaps use the Airport Card and Express for the iMac.
I don't know if this is a good solution, or if there is an easier way to have both computers with internet access. I don't know how to use both the wired and wireless combo as my DSL box only has one Ethernet connection.
I'd rather not have to spend more money on a router, being I just purchased the Airport Card/Express. Speed and security is the most important issue, especially for the new G5. I won't be using the iMac that often, so speed is not a big issue for it.
Any thoughts, comments and suggestions would be greatly appreciated. Please keep in mind that I'm not a techie in anyway.. so any help in simple terms would be great

Glad to hear it is working for you.
The reason you may not be seeing any bandwidth difference may be due to what you are measuring. If you are measuring bandwidth of your DSL connection, that is how fast each computer can upload and download to the Internet, you shouldn't see any difference. This is because your internet connection speed is relatively slow (probably somewhere between 340 kbps and 3 mbps), compared to the available bandwidth of a wired Ethernet connection (can be 100 or 1000 Mbps) or wireless ( 54 mbps). With those kind of numbers, you should see no difference in testing bandwidth of your Internet connection from either computer.
Where you would see a difference is if you were measuring how fast your computers could transfer a file between each other. If they were connected by wired Ethernet, the larger available bandwidth of the connection would make file transfer much faster then the speed seen if they were connected via wireless.
Just a note. All the figures I used for Ethernet and Wireless are theoretical maximums, and currently no equipment will actually reach those speeds, but they are easier to use to illustrate a point then trying to adjust the numbers for overhead and performance issues.
Tom N.

Urgent help with WRT110 Wireless connection

i have got this wireless router a few months ago. since i have gotten it, i have only used hard wired to my desktop. I got a laptop recently, running Vista. I am trying to setup using the wireless with WPA2 personal security. However, i am not supposed get it to connect. It told me unidentified network, and it's not going through to the global earth icon under "Network and Sharing Center".
Now, i have searched solution on google, this is not my first experience setting up wireless, i used to have a WRT54G wireless and it works fine.
Now i have tried all these procedure below:
1) Open the setup page of the router and Under the Wireless tab,Click on Advanced Wireless Settings...Change the Beacon Interval to 50,Fragmentation Threshold to 2304,RTS Threshold to 2304 and Click on Save Settings...Also reduce the MTU to 1400 and click on save settings..Now,check.
2) On all Vista and Win 7 computers, disable IPv6 under the LAN properties for the adapters.
It still doesn't work. Can anybody here help me with this issue? thanks alot

Maybe this will help you but what I do with my adapters when installing is disabling my internet connection, firewall, virus and almost everything. I also turn the internet off then I instal the software. You can try that.cheapest voipcheapest voip callsOSU Beaversfree voip phone calls

Help with Download of Bridge and Lightroom on my MAC

Trying to download Bridge and it never opens. Also trying to download Lightroom and it's been downloading for 5 hours.

Please read, and reply back here with information https://forums.adobe.com/thread/1499014
-try some steps such as changing browsers and turning off your firewall
-also flush your browser cache so you are starting with a fresh browser
http://myleniumerrors.com/installation-and-licensing-problems/creative-cloud-error-codes-w ip/
http://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html
or
A chat session where an agent may remotely look inside your computer may help
Creative Cloud chat support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html

Etherchannel with Cisco wireless Bridges

Hello,
I am trying to create a network in which there are four bridges communicating wirelessly in point to point design(Two bridges on each end of the network which are the connected to Catalyst 3650 switches). I have achieved this design but when I combine the links using etherchannel on the switches one of the link is active and the other inactive. the other link becomes active only when the active links goes down due to STP. Is there a way I can make both links to transmit and receive in a bonded fashion without one of the links being inactive to achieve aggregated throughput. Attached is an example of the network looks like.
I would be grateful if any assistance is given to me in this area.
thanks.

Like Dan mentioned, there is no way you can bond the ports together and make it act like an etherchannel. You either have a primary and backup solution or your configure spanning tree to determine what vlans it should pass to what switch port. This way at least you are using both links and not congesting one link with traffic.
Here is an example"
http://www.cisco.com/en/US/docs/switches/lan/catalyst3560/software/release/12.2_25_see/configuration/guide/swstp.html#wp1020470

Help with T41 wireless driver for Win7

Hi, I have several Tseries (T40, T41, and T43) and I am migrating them to Win7. The T40 went fine, which has a Cisco wireless adapter. I am having trouble with my T41 model 2374-7FG MARG6.
Can you please direct me to the correct driver?
Can you please tell me which adapter I have? The matrix shows it can be three different types and I have tries all drivers, I think.
Thank you,
Rick

Rick, welcome to the forum,
you should have the Intel PRO/Wireless LAN 2100 3B Mini PCI adapter. According to the driver matrice site The Vista driver was available through Windows Update, have you tried running Win. Update to see if it finds it for you?
Hope this helps
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Help with the wireless, please.

I am not having a problem with the iPod's wireless, because it seems to work fine at my friend's house on his unprotected wireless.
The problem is my secured, with a WEP key, internet.
It worked for a little while, but after a month it decided to not work. It connects when the network isn't secured, so I know it's an issue with the WEP key. I want to change my security to a WPA key, and I use an Actiontec GT701-WG Wireless router/gateway. I went to change the security to WPA, but it asks for a whole slew of things I don't know. As anybody ever setup a network with this type of router, and if yes, please tel me how to setup a WPA key!
Thanks in advance for any help.

Oh, and just in case this information is useful, my iPod can connect to the network, password and SSID are accepted. The little "wi-fi" icon appears at the top with a full signal.

Any help with a wireless printer setup?

I recently got a Dell, and an wireless printer with it. The set-up seems pretty straight forward, but I get to the point where on my printer's screen, it gives me a PIN number I am supposed to enter on the WPS page. Problem is, I can't find anywhere on the WPS page where I can enter this number... is there an easy way to simply add another device?
THanks in advance!
-Matt
Solved!
Go to Solution.

Ok.
Which guide does your router look like..
#1 http://www.portforward.com/english/routers/wireless/Actiontec/GT704-WG/wireless.htm
#2 http://www.portforward.com/english/routers/port_forwarding/Actiontec/1020/1st_SMTP_Server.htm
#3 http://www.portforward.com/english/routers/port_forwarding/Actiontec/GT704-WGv2/1st_SMTP_Server.htm
#4 http://www.portforward.com/english/routers/port_forwarding/Actiontec/GT724R/1st_SMTP_Server.htm
#5 http://www.portforward.com/english/routers/port_forwarding/Actiontec/MI-424-WR/1st_SMTP_Server.htm
#6 http://www.portforward.com/english/routers/port_forwarding/Actiontec/MI-424-WRv2/1st_SMTP_Server.htm
#7 None of those.
At this time: Please only look at the screens/guides, do not adjust any wireless (OR port forwarding) settings.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Help with 3945ABG Wireless

Hello to the Board
I'd be most grateful is someone could please help me get my wireless connection up and running on my HP dv2000. I have installed network manager which connects fine when using wired connection.
When I click the network manager icon I can even see my Hub but I just cant connect ('Wireless Networks' is grey and says 'Disconected'). I'm sure it's something embarassingly simple but regardless, I am starting to get frustrated !!
Here is some info:
[ipsofacto@MyBox splashy-full]$ lspci | grep -i net
05:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
08:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02)
[ipsofacto@MyBox splashy-full]$ iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11abg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
eth0 no wireless extensions.
[ipsofacto@MyBox splashy-full]$ dmesg | grep -i wifi
[ 5.004275] iwl3945 0000:05:00.0: Detected Intel Wireless WiFi Link 3945ABG
I am using XFCE4
Apologies if I have left something of importance out. This is the Newbie forum !!
Thanks for reading..
Last edited by ipsofacto2000 (2012-04-09 13:57:29)

linuxxnutt wrote:Is there a hardware switch for the wireless
How could we know if *your* machine has a hardware switch? Think about it.
Anyway, while a ipw3945 problem was reported for 3.4-rc1, it's possible that backporting stuff to 3.3.1 broke that version too. So try this patch: http://marc.info/?l=linux-wireless&m=13 … 427374&w=2
Kernel 3.4-rc2 has this patch already applied, so you could also try that. Yert another possibility is using wireless-compat.
Last edited by Gusar (2012-04-10 08:37:04)

HELP with JMS message bridge to MSMQ

          Can anyone offer suggestions on how to obtain/build a JMS messaging bridge to MSMQ.
          I see that WL has a Messaging Bridge but only for certain foreign messaging systems.
          FioranoMQ have a JMS Implementation with a bridge to MSMQ but a complete JMS implementation
          seems overkill and is costly.
          We already have Weblogic's JMS implementation & just want messages to appear on
          a JMS Queue when they are put in a MSMQ queue. A message driven bean will then
          trigger from the JMS queue.


It is rare to hear of MSMQ when it comes to messaging.
          (I guess MSMQ users typically stay in MS world?)
          I suggest building a minimal subset JMS wrapper. Customers
          have had success with this approach with other queuing products.
          If you can implement asynchronous (onMessage) then the same
          wrapper can be used to plug into MDBs as well as into the bridge.
          You might find that there already is open source
          for these wrappers, search the web.
          Take note that interop is what web-services is supposed
          to be all about. You might want to investigate writing
          an MSMQ app that in turn invokes a WebLogic web-service
          that finally enqueues to a WL queue.
          Another possibility is to write an MSMQ app that invokes
          WebLogic's JMS C client to put messages into a JMS
          queue. The JMS C client is due out
          shortly, perhaps this week, perhaps within the next
          few weeks. It will be posted to dev2dev and work
          with 7.0.
          Tom, BEA
          Pete wrote:
          > Can anyone offer suggestions on how to obtain/build a JMS messaging bridge to MSMQ.
          > I see that WL has a Messaging Bridge but only for certain foreign messaging systems.
          >
          >
          > FioranoMQ have a JMS Implementation with a bridge to MSMQ but a complete JMS implementation
          > seems overkill and is costly.
          >
          > We already have Weblogic's JMS implementation & just want messages to appear on
          > a JMS Queue when they are put in a MSMQ queue. A message driven bean will then
          > trigger from the JMS queue.

I need help with my wireless card of my T60 anyone plz...

It was working fine but then one day, i couldnt get signal from the wireless router, i have tryed installing all of the network drivers and all it says on the divece manager is ""?ETHERNET CONTROLLER"" , and under properties it says OTHER, and this is the ID number of the divice CI\VEN_168C&DEV_1014&SUBSYS_058A1014&REV_01\4&20975680&0&00E1
Can some one plz help me i tierd of being attached to a wire, plz...
and also the the on and off button for the wireless internet in front of the laotop does not do nothin...
I thank You in advance
o yea my Comp is the T60 1951-D12
Message Edited by MxFurious on 08-01-2008 01:06 PM
Message Edited by MxFurious on 08-01-2008 01:07 PM
Message Edited by MxFurious on 08-01-2008 01:10 PM

If it was working then it's something simple. Simple things are usually the hardest to trouble shoot.
Just to begin turn everything off. computer, router, cable modem, everything. relax, take a break and then turn the internet modem on first, then the computer or router, then the computer. I'm hoping your online by then if not...
Then there is something other than simple but fixable.
So I'm thinking... virus software up to date?
Message Edited by T23FUN on 07-09-2008 07:28 PM
ThinkPad T23, 2647 HU8, Based on 2647-8RU: PIII-M 1.20GHz (512KB), 512MB RAM, 40.0GB HDD, 14.1 XGA(1024x768) TFT LCD, 8x8x24x/8x CDRW/DVD, Modem(MPCI), Ethernet(CDC), WinXP Home, Linksys Wireless B adapter.

Help with a wireless bridge

Similar Messages

Maybe you are looking for