Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support

Similar Messages

I bought iphone 5s 2 days ago and suddenly it turn off and start again till the white screen with apple logo and start again

i bought iphone 5s 2 days ago and suddenly it turn off and start again till the white screen with apple logo and start again
please answer me as soon as possible

Hello Ahmedabokamar,
Thanks for the question! I'd recommend taking a look at the following article for troubleshooting steps that can help get your iPhone working again.
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Cheers,
Allen

My iMac wont go past the grey screen with Apple Logo and question mark a caution mark

My iMac wont go past the grey screen with Apple Logo and question mark a caution mark

You may find this support article helpful:
http://support.apple.com/kb/TS2570
Ciao.

My iMac does not move beyond the white screen with apple logo?

When the iMac turns on it does not advance it's start up beyond the 'White Screen' with the apple logo at the center.

the following article addresses the mac booting to gray screen issue you described:
http://support.apple.com/kb/TS2570
you should get resolution from this, good luck!

How to get passed the grey screen with apple logo when turning on?

I got a Imac Intel 20" about 6 years old. The other day turned it on and everscince havent been able to get passed the grey screen with the apple logo on it? What could be the problems and how can i fix this?
cheers

Hello v:
The computer is fairly old and anything can happen. You could try resetting the SMC and see if that helps.
Barry

Got a iMac upon start up it has white screen with apple logo and loading wheel spinning forever under it, does anybody know how to fix this?

PLEASE HELP!!!!!! EMERGENCY Upon start up normal start up noise occurs, then after white screen with Grey Apple logo, and a spinning loading wheel under it (thee repetitive lines NOT rainbow one) ?!? then thats as far as it goes it stays on that screen forever will not boot up. Any info on how to possibly fix? I've tried several of the Start up shortcuts , it wont even start up in Safe Mode . My fiance' is crushed she is a writer and EVERYTHING SHE HAS WORKED ON is somewhere on that hard drive. Any thoughts, i'm open to any and all LOGICAL responses, thank you very much for ya'lls time ........Its just heartbreaking to see my iMac in this vegistated coma,The whole reason i bought a mac was cause I love them I have Apple EVERYTHING, so once again please help.

Try this: Switch off your iMac wait 10-15 seconds hold down the Option Key (alt) key then press the power botton but keep the option key down. This should show all the available options to boot from. I trust you have a full backup, Good luck.

I get the grey screen with apple logo & swirly circle - that's it?

I need to re install Lion X. I went to the Genius bar & the Genius held the alt key (?) then the re-install screen came up. Simple, but i need to do this at home & now it doesn't work!
Do I need the computer on?
Do I hold only the alt key?
Or is it the cmd key?
Please help!
Thanks

Hold the alt/Option key (that's ONE key) at Startup and a completely ROM resident routine called the Startup Manager will draw a gray screen then an Icon for each bootable Volume. then the Eject key is "live" and will open the drawer on a tray-loader.
Select Recovery_HD and you will get to the Utilities/Installer screen you saw before.

TS1367 My MacBook Pro will not go past the grey screen with apple logo in the middle

How do I fix this issue is there anything I can do

Hey there Gonzoeg850,
It sounds like you are unable to boot your computer to your desktop or log in screen. I do not know if you have tried these steps from the article you have up there, but that is exactly where I would start:
Troubleshooting: My computer won't turn on
http://support.apple.com/kb/TS1367
Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
MacBook Pro: How to remove or install memory
MacBook: How to remove or install memory
Mac Pro: How to remove or install memory
Mac mini: How to remove or install memory
iMac (27-inch, Late 2012): Installing or replacing memory
iMac: How to remove or install memory
Reset the SMC.
If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
Thank you for using Apple Support Communities.
All the very best,
Sterling

Computer won't start, grey screen with Apple logo only. Ideas?

Last night my wife's G5 froze. It is a G5 2.0 running OS X 10.4.11. I shut it down (had to use the power button) and tried to restart. No luck, just made it to the grey screen with Apple logo and spinning wheel. After a few seconds the Apple logo disappeared and a black box took its place, then the wheel stopped spinning. It was late, decided top wait until morning before trying again.
This morning I tried to start up again. This time got a warning(?) in upper left that a Firmtek item had already started. I'm sorry I didn't write this all down at the time, so I don't remember the entire message. Since there is a Firmtek card installed in one of the PCI slots I thought that might be the problem, and I pulled the card, as well as another Adaptec card that was also installed. Tried to start again, got to grey screen with Apple but this time no spinning wheel.
Opened media slot manually and inserted Diskwarrior. Tried to start with Diskwarrior but again only reached grey screen. Let run for ~5 minutes, until fans started to run and were begining to get noisy.
Next I reset the PRAM. No luck, still stuck on grey screen. Tried Diskwarrior again, this time got another message in upper left. Here is most of it -
System Failure : cpu=1; code=60000009 (Invalid pmap)
Lateset crash info for cpu1;
Exception state (sv=0x609bb280)
PC=0x000a4ad0; MSR=0x02003000 followed by more similar strings, then
backtrace terminated - unaligned frame address; 0xfc088891
So what's the diagnosis? I've had various issues with my G5s in the past, but have never had one refuse to boot with Diskwarrior before.
Thanks in advance for any help!

Whew, could be many things, from RAM, (or RAM slots/solder issue), to CPU #1 being bad, (CPU#1 is actually the second one.
Does it boot into any of these modes?
Target mode...
http://support.apple.com/kb/HT1661
Does it boot to Single User Mode, CMD+s keys at bootup, if so try...
/sbin/fsck -fy
Repeat until it shows no errors fixed.
(Space between fsck AND -fy important).
Resolve startup issues and perform disk maintenance with Disk Utility and fsck...
http://docs.info.apple.com/article.html?artnum=106214
We might get clues with verbose mode...
http://support.apple.com/kb/HT1492

I just opened my imac, i got the grey screen without apple logo, I just opened my imac, i got the grey screen without apple logo

I just opened my imac, i got the grey screen without apple logo, I just opened my imac, i got the grey screen without apple logo

I am curious as to why you repeated your question twice both in the subject box and in the discussion box?
In answer to your question, have you tried using
Disk Utility?
   1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
   2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
      Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
   3. Click the First Aid tab.
   4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
   5. Select your Mac OS X volume.
   6. Click Repair. Disk Utility checks and repairs the disk.
Then, if you can, reboot to your internal drive and repair permissions.

HT204347 Hi my serial number on bottom of my mac is W8*******66E when l try to try the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not

Hi my serial number on bottom of my mac is W8******66E when l try to turn the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not worked?
<Edited by Host>

What other solutions have you tried?
This may help you:
https://discussions.apple.com/docs/DOC-3353
Ciao.

Imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black

imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black

Hey there mtriest,
It sounds like you are unable to boot the iMac successfully as it keeps shutting down when you try to boot. I suggest the troubleshooting from the following article named:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Disconnect, test peripheral devices and network cables
Note: "Peripheral devices" refers to external devices other than what came with your Mac, such as hard drives, printers, or hubs that you connect via a USB or FireWire cable.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Disconnect all peripheral devices such as external hard drives or printers (leave only the display, a keyboard, and mouse connected).
Disconnect any Ethernet cables.
Start up your Mac.
If you can start up this way, one or more of your peripheral devices (or installed software related to the device) is probably causing the gray screen issue. Connect one device, then restart your Mac to test for the issue. Repeat the process until you locate the device at issue. Make sure the device is powered if it needs to be to operate correctly. Check with the manufacturer of the device for support or possible software driver or firmware updates that may be available for the device. Try a different cable with the device if possible (such as a different USB or FireWire cable).
Note: If you have multiple peripheral devices and the issue only occurs when they are all connected, but not when each device is the only peripheral connected, see the Additional Information section below.
If you are using a desktop Mac with a third-party keyboard and/or mouse device, and the issue still occurs, try starting up with an Apple keyboard and mouse connected instead. Try starting with no keyboard and mouse connected, then connect them after start up. Also, try a different USB port on your Mac.
If the gray screen issue persists with no devices connected, go to the next section (with the peripherals still disconnected).
Perform a Safe BootSimply performing a Safe Boot may resolve this issue.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Start your Mac, then immediately hold the Shift key. This performs a Safe Boot. Advanced tip: If you want to see the status of a Safe Boot as it progresses, you can hold Shift-Command-V during start up (instead of just Shift).
Note: A Safe Boot takes longer than a typical start up because it includes a disk check and other operations.
If your Mac starts up as expected, immediately try restarting.
If the Safe Boot does not work, or the restart after a successful Safe Boot does not work, go to the next section.
There is additional information in the article with further troubleshooting if needed.
Thank you for using Apple Support Communities.
Cheers,
Sterling

HT1349 i upgraded to yosemite last week, now my computer wont start. it stops at white screen with apple logo. what do i do?

i upgraded to yosemite last week, now my computer wont start. it stops at white screen with apple logo. what do i do?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My macbook pro 2011 shows grey screen with apple logo and want start

i was just using my macbook pro and it freezed for a while not responding and i turned it off by pressing the power button. afterwards, i turn it on and it shows a grey screen with apple logo but want start pls somebody help me because am having "my life" on the machine

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

My macbook pro doesn't bootbeyond the grey screen with apple icon and spinning wheel.

My macbook pro doesn't boot beyond the grey screen with apple icon and spinning wheel. I used the "Option" button to access the Disk Utility function and run Repair Disk and Repair Disk Permissions. Should I restart my computer?

The following support article is somewhat outdated. Where it refers to booting from an installation disc, you should boot from your recovery partition (if running 10.7 or later) by holding down the key combination command-R at the chime.
Mac OS X: Gray screen appears during startup

Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Similar Messages

Maybe you are looking for