Hi there, i bought my macbook 1 week ago and its working fine. BUT the fan is always running and it is very annoying? what should i do
hi there, i bought my macbook 1 week ago and its working fine. BUT the fan is always running and it is very annoying? what should i do
Take it back to the store where you bought it for a hardware check and/or exchange/refund.
If they say "that's normal" then get your money back.
Nothing worst than a annoying fan you can't do anything about.
I has a eMac that did that, sounded like a vacuum cleaner running all the time, I'm so glad I trashed it and will never buy a machine I can hear running in a near silent library.
Some advice, the higher end models with a dedicated graphics do tend to operate cooler, it's the one's with only CPU graphics (Intel) regardless if a Mac or PC that tend to make a lot of noise.
Graphics should have never been put on the CPU, it just doubles the heat and doubles the fan noise.
Similar Messages
-
I have an old iPhone 3Gs with software version 4.3.5, I am trying to use it again, and it works fine, but I have not been able to update the software. Every time I try, I get the following message:
"there was a problem downloading the software for the iPhone, the network connection could not be established". This happens even though I have a working internet connection.
Besides that, all the other functions work properly, even synchronize apps and library.
Will I be able to update the software?look around the forum tons of people repport that they can't update
makes you suspect that apples update servers can't meet the depand of too many users
trying to update at once -
Can you charge a macbook by any other means than the power cord? For example the usb drive? My cord works fine but the outlet on the laptop is not.
The only way to charge a MBP is with a MagSafe power supply (wall or airline) try http://support.apple.com/kb/TS1713
-
Hello. I recently pieced together a late 2008 MacBook Pro 15". Everything works fine except the battery constantly goes between "not charging" and "calculating" or, rarely "charging". It does charge after a long while and will report that it is charged.
I have reset the NVRAM and the SMC a couple of time but that didn't work so I ran an Apple Hardware Test and while testing the logic board it gives the following error:
4SNS/1/40000000 LB1T
I've done some research and found this is a temperature sensor related to the battery, but cannot find where the sensor is located in the computer. Would you know how I can find the sensor to test it? Could my battery problem be related to something else? Would a fresh install of Lion help?
Thank you!
Mike
Two pieces of information that may or may not b helpful, the hard drive is from my early 2008 MBP and the only test disc I have access to is from an iMac.Why do you have LION installed on that older machine?
So you say you built a macbook from a bucket of parts eh? Kudos
heres a pic of the battery temp sensor -
I BOUGHT an application from my iphone Application icon and paid 2.99 dollars too, for phone tracker , downloaded sucessfully and its working too but not tracking the phones as mentioned in the description can any one support me??? better from apple!!
Is this the app you're referring to?
http://itunes.apple.com/us/app/phone-tracker/id348537489?mt=8
As you'll note it's made by Presselite and that page has a link to their support.
Also, you'll find it best not to post questions about iPhone apps in the AppleWorks forum. Best to contact the makers of the app.
Regards
TD -
is it free to take my macbook air to an apple store to get a check because the fan is always running?
Yes, the diagnosis at the apple store is free, ....have them find out what is wrong for you
However its totally normal for the fan to be always on, on your macbook Air.
SMC (System Management Controller) could be causing the fan to misinterpret temp. an SMC reset would likely fix this.
If you can HEAR the fan all the time, it might be running noisy due to dust/junk in the fan blades and hub.
If you have pets or a dusty room, fans trap dust and pet fluff like a magnet. Might just need a cleaning. -
Hello, I have the usual issue to use AcroExch.PDDoc/AcroExch.App/AcroExch.AVDoc objects in Visual Basic (MS EXCEL). On my company's machine I have Acrobat X and everything works fine. I am looking for the cheapest solution to get the stuff running on another machine... is there any way to do that with the Acrobat SDK, or do I need to purchase a full version of Acrobat XI ($$) ?
The Acrobat SDK is nothing by itself. It is just information on how to automate Acrobat - just as the Office SDK doesn't include Office, but is for people who already have purchased Office but want to automate it.
These automation things are MARKETING TOOLS FOR ACROBAT. Consider this and the technical limitations make a lot more sense.
So, yes, you need to buy Acrobat. Standard is cheaper than Pro. -
Hi , i have late 2011 model of 13 inch macbook pro. Installled mountain lion . Around 200 gb of free space. Now when i start my mac os the icons lag and it takes time to open up even scrolling the mouse you can see it drag and also the fan runs at high rpm .The cpu processesor runs at peak. When i switch on the windows the fan noise still there but the performance is good.Please advice me what might be the problem and what shall i do to solve it.
Please read this whole message before doing anything.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then copy it. The headings “Step 1” and so on are not part of the commands.
Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Triple-click the line of text below on this page to select it:
kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}' | open -f -a TextEdit
Copy the selected text to the Clipboard by pressing the key combination command-C. Then click anywhere in the Terminal window and paste (command-V). A TextEdit window will open with the output of the command. If the command produced no output, the window will be empty. Post the contents of the TextEdit window (not the Terminal window), if any — the text, please, not a screenshot. You can then close the TextEdit window. The title of the window doesn't matter, and you don't need to post that. No typing is involved in this step.
Step 2
Repeat with this line:
{ sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix)|org\.(amav|apac|cups|isc|ntp|postf|x)/{print $3}'; sudo defaults read com.apple.loginwindow LoginHook; sudo crontab -l; } 2> /dev/null | open -f -a TextEdit
This time you'll be prompted for your login password, which you do have to type. Nothing will be displayed when you type it. Type it carefully and then press return. You may get a one-time warning to be careful. Heed that warning, but don't post it. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step.
Step 3
{ launchctl list | sed 1d | awk '!/0x|com\.apple|org\.(x|openbsd)/{print $3}'; crontab -l 2> /dev/null; } | open -f -a TextEdit
Step 4
ls -1A /e*/{la,mach}* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts .la* 2> /dev/null | open -f -a TextEdit
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 5
osascript -e 'tell application "System Events" to get name of every login item' | open -f -a TextEdit
Remember, steps 1-5 are all copy-and-paste — no typing, except your password. Also remember to post the output.
You can then quit Terminal. -
Umm, not many details really. Recaptcha still works with other websites. Library.nu doesn't list any popups or images as blocked. The site works fine with chrome and opera
If images are missing then check that you aren't blocking images from some domains.
*Check the permissions for the domain in the current tab in "Tools > Page Info > Permissions"
*Check that images are enabled: Tools > Options > Content: [X] Load images automatically
*Check the exceptions in "Tools > Options > Content: Load Images > Exceptions"
*Check the "Tools > Page Info > Media" tab for blocked images (scroll through all the images with the cursor Down key).
If an image in the list is grayed and there is a check-mark in the box "<i>Block Images from...</i>" then remove that mark to unblock the images from that domain.
Make sure that you do not block third-party images permissions.default.images
*http://kb.mozillazine.org/Images_or_animations_do_not_load
There are also extensions (Tools > Add-ons > Extensions) and security software (firewall, anti-virus) that can block images.
*https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes -
I am having trouble seeing my usb printer from my second gen airport extreme using the newest version of airport utility under Mountain Lion. UGH! And while I can see and network to my Canon IP5000 from my macbook pro running leopard, I can't from my new macmini running Mountain Lion. Any help would be appreciated in configuring my macmini so it can see the Canon IP5000 on the airport extreme. Don't want to "share" the printer from the laptop because that would be a cludge. Thanks ahead
I solved this one based on another post. Turned out I needed the snow leopard IP5000 driver. I had just copied over the leopard driver (I had saved my .dmg file) and installed that but it didn't work. So I downloaded the latest driver which turned out to be for snow leopard and I am guessing since it is 64bit that is why it worked and the leopard driver didn't. Anyway, I also had to hook the printer up via usb to the mac mini to get it to work locally before the O/S would see it over Bonjour via the airport extreme.
-
id also like to mention that before it stopped giving me the option to use airplay on my iphone, i had disconnected my apple tv because it was in the sun while i was watching it, and a message popped up saying "temperature: your apple tv is over heating. this message will dissapear when your apple tv is ready,"
Take it in to Apple
-
Please hep me.
I am fine byuying a copy of WIndows 8 but where would I buy it? Also I was wondering wether I would be able to do this without using a disk, solely online, because my boot camp says insert disk.
-
The applications say they are waiting, please i need help.
Thank you very much, i solved the problem rebooting the iPad. :D
-
How do I upgrade my macbook pro to I-Lion without paying, because I bought it three weeks ago just before the release
See "More like this" on the right.
Regards,
Shawn -
I upgraded to Mountain Lion on Macbook Pro today which I bought new three weeks ago, on the upgrade my Ethernet connection is no working, Any ideas on a fix on this issue.
jimr.l wrote:
I upgraded to Mountain Lion on Macbook Pro today which I bought new three weeks ago, on the upgrade my Ethernet connection is no working, Any ideas on a fix on this issue.
If you bought the MBP new 3 weeks ago, it should have come with Mountain Lion already installed. Did you update your MBP to the newly released 10.8.4 update? If not, what OS were you running before the upgrade, and what version of Mountain Lion do you have now?
Maybe you are looking for
-
Falcon 4.0 Allied Forces does not work with Mountain Lion and Nvidia 650M
I have the new Imac with Mountain Lion and the base, built in Nvidia GeForce 650M card. I bought the Falcon Allied Forces game app from the app store, but the in-game graphics are unusable, pixelated, and generally garbage. It does not appear there
-
Ipod mini keeps turning itself on and playing
Hi, Hopin gsomeone can help me here. My iPod mini keeps turning itself on and playing..thus running down the battery overnight. I've checked that the alarm clock is set to OFF. I turn the iPod off, put Lock on the keypad and in the morning, it's turn
-
BAdI: Field LIFNR not ready to accept input (Change will not be adopted)
Dear Guruz...\ given below is the warning with message number BAdI: Field LIFNR not ready to accept input (Change will not be adopted) Message no. MIGO050 while i am trying to enter the batch name for removal for scrapping and clicking check this war
-
Problem to run servlets in web logic
dear fnds please solve my problem, i created a domain in weblogic server using configuration wizard.but after deploying i cannot get the servlet. please provide me the url how to access that file.
-
Hello, just wondering how I would add an "else if" statement to the following. (weather == "hail") ? trace("bringMotorcycleHelmet") : trace("bringStrawHat"); thanks for any help.