How to Bridge PACE 5031 NV to 3rd Party Router?

People say it's a lot like the 2Wire 3600, but the menus don't look the same to me. I Happily follow instructions with screenshots. My local tech geek is not able to handle this for some reason... Help?

Got my internet speed (cake) and gigabit LAN (eating it, too)! The trick I believe was 'Attack Detection' in advanced FW settings.
See here: http://forums.att.com/t5/Device-Setup/AT-amp-T-Modem-Router-Apple-Airport-Extreme/td-p/3607835#.Uw1oVfldUoA
There is no true bridge mode on the 2Wire routers. However, you can still configure it such that almost all functions of your own router will work properly.
1. Set your router's WAN interface to get an IP address via DHCP. This is required at first so that the 2Wire recognizes your router.
2. Plug your router's WAN interface to one of the 2Wire's LAN interfaces.
3. Restart your router, let it get an IP address via DHCP.
4. Log into the 2Wire router's interface. Go to Settings -> Firewall -> Applications, Pinholes, and DMZ
5. Select your router under section (1).
6. Click the DMZPlus button under section (2).
7. Click the Save button.
8. Restart your router, when it gets an address via DHCP again, it will be the public outside IP address. At this point, you can leave your router in DHCP mode (make sure the firewall on your router allows the DHCP renewal packets, which will occur every 10 minutes), or you can change your router's IP address assignment on the WAN interface to static, and use the same settings it received via DHCP.
9. On the 2Wire router, go to Settings -> Firewall -> Advanced Configuration
10. Uncheck the following: Stealth Mode, Block Ping, Strict UDP Session Control.
11. Check everything under Outbound Protocol Control except NetBIOS.
12. Uncheck NetBIOS under Inbound Protocol Control.
13. Uncheck all the Attack Detection checkboxes (7 of them).
14. Click Save.
Your router should now be able to route as if the 2Wire was a straight bridge, for the most part.
Inbound port 22 might be blocked, and inbound ports 8000-8015 might also be blocked, and there's nothing that can be done about it.
This is how I have my 2Wire configured, and I have a Cisco 2811 behind it doing IPSec, IPv6 tunnels, etc.

Similar Messages

Accessing secure sites with 3rd party router

I want to use my original router "Buffalo WBMR G54" with BT and have been for a short while but cannot access online banking or barclaycard online, works ok with home hub. Tried both firefox and IE8, pages just hangs on both browsers.
Any techies around know why this is please? My Buffalo worked fine as a 3rd party router with talktalk

wehey23 wrote:
Can you tell me how to change the MTU settings for the BT Hub pls?
I have just moved home and have taken BT BB with me.....the internet is running fine but i cant connect to secure sites at all. Have tried contacting BT and they have tried everything but cant help!
Thanks
First check your Firewall is not blocking SSL port 443.
This thread contains most of the information you may need to change you PC MTU value, I don't think the Homehub MTU value can be easily changed?
http://community.bt.com/t5/BB-in-Home/BT-Broadband-and-MTU/m-p/12660;jsessionid=F92D7A9C8D5A07CAE73C...
"I have this awful feeling someone is watching every move I make (one of my pet hates is router location tagging)." Marvin (A paranoid Android)

3rd Party Router and an iMac with Airport card

Could someone assist me in setting up an older flat panel iMac 800Mhz with a airport card to a 3rd party router (Speedport W 500V). It was really easy to set up the DSL etc when connecting to an Airport Extreme base station, however I have upgraded and trying to get conencted at my parents place, which have DSL but with the Speedport W 500V modem/wireless combo - any assistance to get the two connected would be appreciated.

Is there a SW tool similar to the Airport Admin
Utility which will allow setting and management of
the third party router?
There may be (probably Windows only) or you need to use a web based configurator. It will depend on what the manufacturer of your router provides.
The manual which came with the router (it may be in electronic form) should provide guidance on how to configure the router via a browser.
iFelix

HT1515 My internet 3rd party access point in in the basement and the speakers I want to stream music to wirelessly are upstairs. Does Airport Express need to be connected to my 3rd party router via ethernet cable or will it stream music wirelessly?

My internet 3rd party access point in in the basement and the speakers I want to stream music to wirelessly are upstairs. Does Airport Express need to be connected to my 3rd party router via ethernet cable or will it stream music wirelessly?

Wirelessly
Just select the option to make your AirPort Express join an existing network in the setup process

Buffalo WHR-600D & Youview+ 3rd Party Router

Hi,
I have just received my youview+ box and am unable to view the extra channels and BT sport using my Buffalo WHR-600D router.
The BT HomeHub does not have the extra functionality I need so am looking for the settings I need for my router to make it work.
Many Thanks,

https://community.bt.com/t5/YouView-Boxes/Using-a-3rd-party-router-for-Multicast/td-p/1048582

Use express as a wifi extension wirelessly with 3rd party router

Hello,
I've just purchased an Airport Express. I want to use it to extend the wifi range to upstairs of my Virgin Media Superhub (downstairs).
I have read that you need to connect the two together with an ethernet cable if using a 3rd party router (not Airport Extreme or Time Capsule). I have connected the AE it to my macbook pro via airport utility wirelessly (without an ethernet cable) and the light is green and the signal seems to have slightly extended. So it seems to have worked for my MBP.
The problem is when I use it with my iPhone 5, despite showing up on the airport utility app, when I go close to the Airport express (upstairs) it doesn't improve the wifi signal at all and sometinmes lose signal completely. The airplay also works with my MBP but cuts out with the iPhone.
Is it possible to connect it wirelessly like I have done or have I just been tricked into thinking the signal has improved?
I'm currently running OS 10.8.5 on MBP and iOS 7 on the iphone 5.
I've tried to articulate this easily and I'm sure someone has already asked this but any help would be appreciated.
Thanks

The trick would be to locate the Express where you need more wireless signal coverage and connect it back to the SuperHub using an Ethernet cable.
You can run an Ethernet cable up to 330 feet or 100 meters with no signal loss.
If you cannot run an Ethernet cable, you might want to take a look at a pair of Ethernet powerline adapters to send the Ethernet signal over the AC powerlines in your home. The theory here is that you already have the wiring in place, you just need the adapters.
Any computer/electronics superstore will have a selection of powerline devices on hand from which to choose.
I doubt that you would notice any improvement at all if you located the Expess close the SuperHub, and it might actually interfere with the signal from the SuperHub, so that location would not be recommended.

How to Collect IDOCS before sending to 3rd party

Hi All,
I am sending out PO's using ORDERS idoc from SAP to 3rd party.
In my scenario I need to group the similar IDOC data into a single file before sending it out to the 3rd party using XI. So in Partner profile I have choosen 'Collect IDOC' option and given the count as 10.
Once IDOCS were generated they were in Status '30'. So I then ran RSEOUT00 to flush the PO idocs to XI. It did flush them out but as individual IDOCS.
I had the impression that 'Collect IDOC' files the selected IDOCS into a SINGLE file/IDOC and then sends it out. Was I right in assuming that collect IDOCS merges all idocs into 1 file/idoc or is it wrong.
If it does not, is there a way how I can merge all these IDOCS into a single file before sending to 3rd party ?
Thanks
Shirin

Hi Shirin,
For IDoc packages see -
XI:Idoc Message Packages
The specified item was not found.
For IDoc Bundling see - The specified item was not found.
Also, to see BPM Collect patterns, you can navigate to the SWCV named SAP BASIS in your IR. Under namespace http://sap.com/xi/XI/System/Patterns you will find the integration process called BpmPatternCollectPayload. There are many examples in this namespace.
If you are new to BPM, see this - [Step by Step Guide to BPM|http://www.riyaz.net/blog/index.php/2008/04/16/a-step-by-step-guide-to-bpm-asynch-sync-bridge/].
Hope this helps.
Regards,
Riyaz

How to trace Logs for WebService connectivity - 3rd Party to ECC

Hi Experts,
Basically it's a simple scenario, the 3rd party will send a soap request with the information in it and wiill be sent to ECC and be written on a table.
I'm wondering on how to trace logs on the soap request sent from 3rd party to an ECC environment. I used Altova XMLSpy and soapUI and to create a soap request from wsdl created in SOAMANAGER. Both of the software returns a response. Do these both of these software really sends data (soap request) going to the binded address or it's just i simulation that wsdl created is valid.
Cheers,
R-jay

Hello,
These third party tools send web service requests to SAP system. You can trace Service invocation and download the request and response payloads using SOAMANAGER. In Logs and Trace tab, edit the Trace configuration with suitable trace level and expiration time.
Thanks,
Venu

Anyone know how to upload the HTS files from 3rd party provider to GTS??

We are having following files provided by 3rd party provider - CUSTOMS Info
NAFTA ROO
U.S. HTS
Per provider, SAP has developed a system so that GTS users can automatically reclassify items that are effected by a change and they have asked us to program the HS data needed.
Anyone know how to do that?
Please advise,
Appreciated.

Hi Reddy,
Thanks for your input firstly, and i still need ur advise on the HTS upload.
1. Below is the HTS files provided by 3rd party company. and I noticed that there is 3 types of files. "DTR" , "Nom" and "Txt". Could you explain what are they? and If I need to upload them seperately?
2. Follow the procedure your provided - "classification > upload manually HTS codes into GTS system" Actually, I didn't find upload mannually HTS codes into GTS IN THE SAP CUSTOM Managment.
I tried "Load Traiff Code Numbers from XML files" and "Load Commodity code from XML file".
1) "Load Traiff Code Numbers from XML files"
2) "Load Commodity code from XML file".
   a) Select all files.
        - fill in "Data Provider",
        - "XML Files"-All files selected.
        - check " Output list", "simulation mode" "Nomenclature Active" and "Activate All Text Types"
        - no "Alternative Numbering Scheme" selected, and other selected.
        Error msg found:
        - Unable to find any defined structures for tariff assignment rule set "_DHSCN"
        - Incorrect order. Enter the first file(see long text)
    b)   only select "HSCN_Txt_I_00002001001.xml", the other is the same like bove.
          1. prompted to select a "From-Time Zone",   Select "UTC+8"
          2. Simulation was carried out successfully
    c) only select "HSCN_Nom_I_00002001002.xml", the other is the same like above.
          But I meet error for this file: "Incorrect order. Enter the first file(see long text)"
    d) only select "HSCN_DTR_I_00002001007.xml", the other is the same like above.
          meet error msg:
          "Unable to find any defined structures for tariff assignment rule set "_DHSCN""
HTS xml files of China from 3rd party provider
+++++++++++++++++++++++++++++++++++++++++++++++++++
2008-05-02 10:53         7,483,730 HSCN_DTR_I_00002001007.xml
2008-05-02 10:53         7,980,857 HSCN_DTR_I_00002002007.xml
2008-05-02 10:53         7,765,896 HSCN_DTR_I_00002003007.xml
2008-05-02 10:53         7,605,204 HSCN_DTR_I_00002004007.xml
2008-05-02 10:53         7,743,890 HSCN_DTR_I_00002005007.xml
2008-05-02 10:54         8,007,036 HSCN_DTR_I_00002006007.xml
2008-05-02 10:54         3,883,316 HSCN_DTR_I_00002007007.xml
2008-05-02 10:51         6,087,448 HSCN_Nom_I_00002001002.xml
2008-05-02 10:51         4,955,900 HSCN_Nom_I_00002002002.xml
2008-05-02 10:50           260,960 HSCN_Txt_I_00002001001.xml
+++++++++++++++++++++++++++++++++++++++++++++++++++

How do I get my iWork'09 3rd party Keynote themes into Keynote 6.0?

1. I had iWork '09 installed on my computer from the old installation disk. It was not clear at the keynote that I would receive the updates for free as I already owned them. I was expecting to see the updates when I opened up the App Store, but they were not there which gave the impression that I was SOL since I didn't purchase them through the App Store. I even received the message "[App name] is already installed, purchase anyway?", but that message is cryptic and not clear that I was going to receive the update, so I wound up purchasing the iWork apps again, just to wake up this morning to find out that I should have received them for free. I am truly hoping for a refund, because at $20 each, that's a big difference between that and free.
2. I opened up keynote to play with the new features, but because the internal architecture is different, it no long references my old themes folder in Library > Application Support > iWork > Keynote. I have tried copying the files to other permutations of possible reference folders in the global and user libraries, but have had no success. These 3rd party themes were not cheap either. I'm sure there is a way to get them to show up in the Keynote Theme Selector, but I haven't stumbled on it yet. Does anyone have any suggestions?

Thanks for the link to the troubleshooting tips! It contained the correct answer which is:
"If your documents or changes still don’t appear, try creating a new document on your iOS device, and then check again for existing documents from iCloud to appear".
I created a test document in Pages and when I returned to my documents all the documents from iCloud reappeared.

How to unlock iPhone 4s bought from 3rd party Carphone Warehouse UK

Hi everyone!
Hope you can help?
I purchased an iPhone 4s from Carphone Warehouse UK with an Orange contract. I am traveling to the USA shortly and I would like to use a local SIM card whilst out there as it will dramatically reduce my cost for data etc.
I contacted Orange to unlock my phone. They initially said that they could do it, but when they pulled my details up they said that because I purchased my iPhone through a 3rd party (Carphone Warehouse) and that the handset was not 'Orange branded' that they were unable to do it! I will need to contact Apple to unlock it.
I rang Apple and they said categorically that they do not unlock phones and it is the responsibility of the network to unlock the handset.
I rang Orange back with Apples response. They still said that they could not do it. I tried to reason with them, explaining that I wanted to get unlocked from THEIR network. But apparently its the phone that gets unlocked and not the network?
I decided to go back to my point of purchase. Carphone Warehouse said that they don't unlock phones and that it was a very 'grey' area. They said, that what ever SIM card is initially inserted into the handset, it automatically locks to that network? They didn't like to confirm who is responsible to unlock the phone (Orange or Apple) but they were leaning more toward Apple.
So my questions are:
Has anybody else had the same problem?
Has anybody else resolved this issue?
If this is not possible, can anybody offer any alternatives, other than roaming bundles etc, as they are still expensive?
Thank you all very much for reading this, I hope to hear from you soon,
Ceri

ONLY Orange can unlock your iphone. No one else at all. ONLY Orange.
Locking and unlocking is at the sole discretion of the carrier.
You will need to keep taking to Orange.

Using a 3rd party router for Multicast

Hi all,
There’s a lot of feedback on this board about using third party routers with Multicast, so we’ve decided to put this information all in the one place for you.
NOTE: the workarounds below haven’t been tested by BT as we do not support 3rd party routers and we do not endorse any of them. Our recommended router remains the Home Hub.
With the above statement in mind, we know that a lot of you do choose to use other routers. The information contained here has come from fellow customers who have given their time to share this information in good faith. Thanks to all of the forum members who have helped make this information available to our community it is a great example of the wealth of information that a community can provide and we hope this encourages users to come back and visit us in the future.
A special mention goes to walkerx who has posted and prompted a lot of the provided information.
Hub configurations in alphabetical order:
Apple Airport Extreme
Put your Airport Extreme into Bridge Mode and turn the Home Hub's wireless off.
[From MartinH's post]
ASUS RT-N66U
You must configure 'Enable VPN + DHCP Connection' to 'No' under the WAN option.
Settings used were:
- Have router on the latest firmware: 3.0.0.4.374.130
- Use the following settings in LAN > IPTV:
- 'Select ISP Profile' = None
- 'Choose IPTV STB Port' = None
- 'Use DHCP routes' = Microsoft
- 'Enable multicast routing (IGMP Proxy) = Enable
- 'Enable efficient multicast forwarding (IGMP Snooping) = Enable
- 'UDB Proxy (Udpxy) = 0
[From sepph's post]
Billion 7800DXL
Router has been reported to work.
[From walkerx's post]
Billion 7800N
Requires you to add another profile (Pure Bridge) to the EWAN port along with the PPPoE profile. Save settings & restart. Also enable IGMP proxy & snooping.
[TimCurtis' post]
DLink Dir 825
If enable multicast you can see the on-demand players but get an IPC6023 error when viewing the test channel (this means poor internet channel quality). This error message comes up even though it works if use the Home Hub 4
[walkerx's post]
Netgear R6300
Netgear R6300, but with the Home Hub 3.0 and 500Mbit Powerline adapters in the picture.
Modem -> HH3 -> R6300 -> Powerline -> 2 x Youview Boxes on other Powerlines.
To do this, configure the Home Hub 3.0 as 192.168.1.1, then disable its wireless and DHCP. Make sure that NAT and UPNP were enabled, and then set it to use the address 192.168.1.254 as a DMZ server.
Then configure the R6300 as the address 192.168.0.1, using the WAN IP address of 192.168.1.254, with 192.168.1.1 as the gateway and DNS server. The R6300 is then connected via WAN port to the HH3 Gigabit port.
In the R6300 settings switch on IGMP.
The above settings allow both YouView boxes to use on demand content and different streaming channels simultaneously, as well as giving the full features of the R6300 such as AC1750 wireless, network printing, and DLNA
[wigglr's post]
TP-Link AC1750
Router has been reported to work.
[zarf2007's post]
TP-Link Archer C7
Router has been reported to work.
[HappySlayerUK's post]
TP-Link TL-WR1043ND
No configuration needed, plug and play.
[walkerx's post]
TP-Link WDR4300 N750
Router has been reported to work.
[aseymour's post]
TP-Link TL-WDR4900 N900
Router has been reported to work, plug and play.
[cactusbob's post]
TP-Link routers in general
How to configure Multicast on TP-Link routers (from the TP-Link website).
One of our posters also found the following:
He found that your router must be able to do the following for Multicast:
For an end user connected via Openreach GEA (FTTC and FTTH)
• The Residential Gateway will support:
– IPoE for multicast traffic and PPPoE for BB traffic;
– VLAN tag ID of 0 or no VLAN tag ID for multicast and BB traffic;
– Fork IGMP requests up multicast and BB paths.
For an end user connected to an MSAN (WBC copper)
• The Residential Gateway will support:
– A dual VC architecture;
– Accept TV Connect multicast traffic on ATM VP/VC 0/35 with IPoE and broadband traffic on ATM VP/VC 0/38 with PPPoE;
– Fork IGMP requests up multicast and broadband paths.
IGMP should v3 and will be in range from 225.0.0.0 to 239.255.255.255
[walkerx's post]
List of routers that do not appear to work:
Draytek 2750n
Linksys EA4500
linksys EA6300
Netgear AC6300
[From Red_Snow's post]
If you use a router that’s not listed here, do a search on the YouView from BT board to see if advice has been posted elsewhere. If it hasn’t, do post your question.
Thanks,
Stephanie
Stephanie
BTCare Community Manager
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post. If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Thanks for confirming that quails.
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

Changing router to 3rd party router

I've been thinking about upgrading my router to a 3rd party AC wireless router so I can use more of my bandwith on my laptop and other wireless gadgets. My question is can I change it and keep all my tv services. I was told I have to use verizon's as a bridge. If I can how would I go about doing it.

Check your new router's manual for how to put it into Access Point Mode. (most new AC routers just require changing a setting, some/ those without an explicit setting will require you turn off DCHP and make sure it is plugged in via one of its LAN ports ).* All your services will remain because your Actiontec will essentially be doing all the heavy lifting. You can even leave the WiFi on the old router on but I would recommend spacing out the channels to prevent interference. (also it is not very neighbor friendly if you live in an apartment)
Bridging the Actiontec is only needed if:
You have a pretty old one and want to do a lot of torrenting/ gaming (the older ones have small NAT tables ... I think any of the ones over 100,00 should be fine for most)
You want to use some specialized features besides WiFi on your new router (its firewall, advanced management of the usb port, ect.... Access Point mode disables some of these features)
You have time to waste
You have so much heavy traffic/ devices on your router that the cpu/ ram of your new router will make a difference (unlikely)
Anyway, if you do bridge (and it is a fun little project if you have the time), you can create a double bridge which shouldn't be much harder to fix the On Demand problem**. It is option 5 of this guide: http://www.dslreports.com/faq/16077
*Just plugging the router in normally without putting it in Access Point Mode means all your WiFi internet traffic has to go through two routers to reach the internet. It will likely work most of the time, but it may cause unnecessary problems with devices on your network communicating to each other and also port forwarding which is important to a lot of applications.
**Only On Demand and DVR will go away with a regular bridge... Not your entire TV service. (possibly the tv guide/ on screen caller ID but I've heard from multiple people that is not the case)

Working with a 3rd party router

I have a Netgear Nighthawk R7000 and wish to use it rather than the gateway (3801HGV) that was provided. I realize that At&t doesn't support 3rd party routers, so I thought I'd ask here.The current setup is: Gateway>Netgear>devices. The netgear is connected as a DMZ port on the gateway. They also have separate subnets. Gateway is 192.168.1.x and netgear is 192.168.2.x. The Netgear has the ports open for Xbox Live. I have 3 devices on the network that don't seem to be working correctly. Two of those devices are TV receivers (wireless and wired) and the other is an Xbox One. The wired receiver and Xbox are connected to a Gigabit switch over by the TV. The TVs freeze and say they lose connection even though they show 10-30 seconds of the channel chosen.The Xbox is having issues keeping connected to party chat. Games and other apps work properly. To work on some troubleshooting, I connected the cables that go to the TVs to the gateway and the TVs are working properly, but I would like everything to be run through the netgear. I'm not the one who plays Xbox, so I am not yet able to test. Is there anything I can do to configure the Netgear or the gateway to allow all devices to be routed through the Netgear? Any help is appreciated.

As my thoughts has said, AT&T doesn't support sending IPTV traffic through a third party router. If you have a third party router that properly implements IGMPv3, then you may be able to do so, but understand that AT&T doesn't support it. I do not believe your router falls into this category anyway, so it's a moot point.
The symptoms of running your IPTV traffic through a router that doesn't support it is exactly what you've experienced, you get picture for 10-20 seconds after a channel change, then it's lost. I'm guessing that your issue is that you have only one Cat5e cable run between where the RG and router are and where a TV Receiver and the Xbox are and you need to run traffic for both over that same wire. Options are (a) get a Wireless Receiver, (b) use two VLAN with tagging capable gigabit switches to send the tagged traffic over the single cable, then separate it out at the remote switch.

How do I set class path for 3rd-party classes?

Hello, I need to know how to set the classpath so that I can use the apache's third-party lang classes. I downloaded commons.apache.org/lang/download_lang.cgi. And I need to know next steps. Move the unzipped files to which location? And type what commands?
Thanks, Melissa

Hi, it's not the server that I am running. My instructor told me to download an apache class file for the Apache Lang library and then set my class path to point to the executable. Her instructions are for Windows users, however. I need to do something in the terminal shell but I don't know precisely what.
mg

How to Bridge PACE 5031 NV to 3rd Party Router?

Similar Messages

Maybe you are looking for