How to build distribution package with Agilent VISA as primary

Hi everybody,
I build a distribution package under LW 8.0 in a PC(Agilent VISA is primary), then I install the distribution package in another PC.
But I found the distribution package install NI VISA as primary in another PC. So How could I make Agilent VISA as primary when I build Distribution Package?
Does anyone can help me?

TaoZ,
Does your application use both NI-VISA and Agilent VISA? NI-VISA is only functional as the primary VISA, so if you need to use both NI-VISA and Agilent VISA, Agilent VISA will need to be secondary. If you are using just Agilent VISA, then you should not need to install NI-VISA. If you already have NI-VISA installed on the system, then typically Agilent VISA will overwrite NI-VISA because they use higher version numbers than us, but this is not necessarily always the case. Which version of each driver are you working with?
National Instruments
Product Support Engineer

Similar Messages

How to build a package with a hyphen

Hi guys,
Im trying to make my own wine 1.0-rc1
Ive tried just changing the pkgver but i get
ERROR: pkgver is not allowed to contain hyphens.
so what is the preferred method of doing it?
Thanks

kumico wrote:i think the convention is to create a new variable called _pkgver with the real required pkgver, and set pkgver to one without the hyphen
no it is not. Please be sure you've read the Arch packaging standards before commenting on such things.
http://wiki.archlinux.org/index.php/Arch_Packaging_Standards wrote:Do not introduce new variables into your PKGBUILD build scripts, unless the package cannot be built without doing so, as these could possibly conflict with variables used in makepkg itself. If a new variable is absolutely required, prefix the variable name with an underscore (_)

How to build a array with high sampling rates 1K

Hi All:
Now I am trying to develop a project with CRio.
But I am not sure how to build a array with high sampling rates signal, like >1K. (Sigle-point data)
Before, I would like to use "Build Arrary" and "Shift Register" to build a arrary, but I found it is not working for high sampling rates.
Is there anyother good way to build a data arrary for high sampling rates??
Thanks
Attachments:
Building_Array_high_rates.JPG ‏120 KB

Can't give a sample of the FPGA right now but here is a sample bit of RT code I recently used. I am acquiring data at 51,200 samples every second. I put the data in a FIFO on the FPGA side, then I read from that FIFO on the RT side and insert the data into a pre-initialized array using "Replace Array subset" NOT "Insert into array". I keep a count of the data I have read/inserted, and once I am at 51,200 samples, I know I have 1 full second of data. At this point, I add it to a queue which sends it to another loop to be processed. Also, I don't use the new index terminal in my subVI because I know I am always adding 6400 elements so I can just multiply my counter by 6400, but if you use the method described further down below , you will want to use the "new index" to return a value because you may not always read the same number of elements using that method.
The reason I use a timeout of 0 and a wait until next ms multiple is because if you use a timeout wired to the FIFO read node, it spins a loop in the background that polls for data, which rails your processor. Depending on what type of acquisition you are doing, you can also use the method of reading 0 elements, then using the "elements remaining" variable, to wire up another node as is shown below. This was not an option for me because of my programs architecture and needing chunks of 1 second data. Had I used this method it would have overcomplicated things if I read more elements then I had available in my 51,200 buffer.
Let me knwo if you have more qeustions
CLA, LabVIEW Versions 2010-2013
Attachments:
RT.PNG ‏36 KB
FIFO read.PNG ‏4 KB

How to build a screen with master detail data

Hi ,expert ,
Someone can teach me how to build a screen with master detail table ?
I wnat to build a screen for user to maintain FERT group and FERT detail list in one screen .
just like this ..
MASTER Block
FERT1
FERT2
FERT3
DETAIL Block
FERT1A1
FERT1A2
FERT1A3
when I double click FERT1 in the Master Block the detail view will show FERT1A1 A2 A3
Thanks for your help ....
Moderator message : Not enough research before posting. Spec dumping not allowed. Thread locked.
Edited by: Vinod Kumar on Jun 13, 2011 1:38 PM

An inefficient way to create the array is to use the build array and a shift register as shown below. It's more effecient in terms of memory management to create the array and then use the replace array subset as shown in the other image. Of course, if you don't need the array inside the loop, just wire the value out of the while loop and on the exit tunnel, right click and select 'Enable Indexing'.
Message Edited by Dennis Knutson on 07-03-2007 10:25 PM
Message Edited by Dennis Knutson on 07-03-2007 10:26 PM
Attachments:
Crude Build Array.PNG ‏4 KB
Better Build Array.PNG ‏6 KB

How to call a package with ADO?

I have designed a package which include a procedure. And I have a program coded in ASP.
How to call this package with ADO. Please give a sample.

Hi,
I persume that you are facing this problem when u try to code in VB. If that is the case here comes the code.........
OraDatabase.Parameters.Add "A_NBR_NEWSID", A_NBR_NEWSID, ORAPARM_INPUT, 2
OraDatabase.Parameters.Add "A_NBR_TOPICID", A_NBR_TOPICID, ORAPARM_INPUT, 2
OraDatabase.Parameters.Add "A_NBR_USERID", A_NBR_USERID, ORAPARM_INPUT, 2
OraDatabase.Parameters.Add "result", 0, ORAPARM_OUTPUT
OraDatabase.Parameters("result").serverType = 2
OraDatabase.ExecuteSQL ("declare result Number; Begin :result := PKG_CONTENT_MANAGEMENT.FUN_GET_NEWS_PERM_BY_USERID(:A_NBR_NEWSID, :A_NBR_TOPICID, :A_NBR_USERID); end;")
OraDatabase.Parameters.Remove "A_NBR_NEWSID"
OraDatabase.Parameters.Remove "A_NBR_TOPICID"
OraDatabase.Parameters.Remove "A_NBR_USERID"
FUN_GET_NEWS_PERM_BY_USERID = OraDatabase.Parameters("result").Value
OraDatabase.Parameters.Remove "result"
Hope this clear your doubt..
Raj

[SOLVED] How to install AUR packages with patchname.patch

Hi all,
I'm trying to install lottanzb from the AUR and there's are a dependency called par2cmdline 0.4-13 that has a lot of nameofpatch.patch that are included in the AUR par2cmdline 0.4-13 package page that just open up to a url that shows code.
I created patch files from the code displayed in the url with a text editor and added them to the extracted LOTTANZB folder in my build directory but when I go to build the package with PKGBUILD it runs through a check sum while building and the checks don't match.
I'm obviously doing something fundamentally wrong here. Can someone direct me?
Thanks,
Last edited by bennylb0 (2010-05-28 13:30:16)

Hi, thanks for reply.
Sorry, my mistake.
I did place patch files inside the par2cmdline-0.4 folder. The only reason I created the .patch files and placed them inside par2cmdline-0.4 folder was because the PKGBUILD as well as the other 5 .patch files didn't exist inside the extracted build folder. They only place I could find them was in AUR par2cmdline-0.4 displayed as a url.
When I copied and created the PKGBUILD as it did not exist inside the extracted folder par2cmdline-0.4 folder I received the following error:-
Error autoconf.patch was not found in the build directory and is not a url. That along with 4 others do not exist in the build directory.
You can see this bellow:-
[ben@ben par2cmdline-0.4]$ makepkg
==> Making package: par2cmdline 0.4-13 i686 (Fri May 28 22:08:21 EST 2010)
==> Checking Runtime Dependencies...
==> Checking Buildtime Dependencies...
==> Retrieving Sources...
-> Downloading par2cmdline-0.4.tar.gz...
--2010-05-28 22:08:23-- http://downloads.sourceforge.net/source … 0.4.tar.gz
Resolving downloads.sourceforge.net... 216.34.181.59
Connecting to downloads.sourceforge.net|216.34.181.59|:80... connected.
HTTP request sent, awaiting response... 301 Moved Permanently
Location: http://downloads.sourceforge.net/projec … 0.4.tar.gz [following]
--2010-05-28 22:08:23-- http://downloads.sourceforge.net/projec … 0.4.tar.gz
Reusing existing connection to downloads.sourceforge.net:80.
HTTP request sent, awaiting response... 302 Found
Location: http://transact.dl.sourceforge.net/proj … 0.4.tar.gz [following]
--2010-05-28 22:08:24-- http://transact.dl.sourceforge.net/proj … 0.4.tar.gz
Resolving transact.dl.sourceforge.net... 202.55.147.10
Connecting to transact.dl.sourceforge.net|202.55.147.10|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 239312 (234K) [application/x-gzip]
Saving to: "par2cmdline-0.4.tar.gz.part"
100%[===================================================>] 239,312 179K/s in 1.3s
2010-05-28 22:08:26 (179 KB/s) - "par2cmdline-0.4.tar.gz.part" saved [239312/239312]
==> ERROR: par2cmdline-0.4-autoconf.patch was not found in the build directory and is not a URL.

HT3951 How can I buy music with my visa card in nigeria

How can I buy songs with my visa card in Nigeria

Itunes verifies your account using your billing info.
If your credit shows in the top right side of the itunes store, then it will take it from that balance.

How can uesd app store with out visa to dawnload free app only

Hello
How can uesd app store with out visa to dawnload free app only

There are instructions on this page for how to create a new account (the instructions won't work with existing accounts) without giving credit card details : http://support.apple.com/kb/HT2534

How could I transport package with all content within

How could I transport package with all content ( I do not get it with se80->"write transport entry") or by entering in se10 in transport request object R3TR DEVC.

go to SE03
choose the third item "include objects in a request" by double-clicking
there you set the first parameter "Package" to your package and execute
note: you can also deselect the radiobutton "All objects" and set "Selected objects" then you will be able to fine-tune the list of objects

How to use single ant build to package with and without native extensions

Hi,
I am using iOS native extensions for Adobe air. For this I am listing the extensionid in the application descriptor file. Since the package with native extensions are meant to run only on device, I want my build script to work without native extensions too to be able to run on simulator. Is this manadatory that I need two separate application descriptors/basically two build scripts to compile and package them? Please suggest and let me know if more explanation is needed.
Thanks,
Swathi.

why are you wanting to use single frames?
They allow having the initial frame address stay in the
address bar, and not
show the linked page's address. The problems they cause
usually override any
value.
Or- if we aren't using the same words the same way, please
give an example
site of what you want to do.
Alan
Adobe Community Expert, dreamweaver
http://www.adobe.com/communities/experts/

How to build a array with collected data

Hi,
I have collected data from serial port with VISA. Now I want to build a array with 100 date points. Should I connect VISA Read with Build Array directly? How to do it?
PS: All of them are in a While Structure.
Thank you!

An inefficient way to create the array is to use the build array and a shift register as shown below. It's more effecient in terms of memory management to create the array and then use the replace array subset as shown in the other image. Of course, if you don't need the array inside the loop, just wire the value out of the while loop and on the exit tunnel, right click and select 'Enable Indexing'.
Message Edited by Dennis Knutson on 07-03-2007 10:25 PM
Message Edited by Dennis Knutson on 07-03-2007 10:26 PM
Attachments:
Crude Build Array.PNG ‏4 KB
Better Build Array.PNG ‏6 KB

[solved] building a package with bjam

Hello all,
I'm trying to figure out how to create a package that builds with bjam. When I build the package manually, I only need to run
./bjam --prefix=/usr --with-feature1 --with-feature2 ...etc
and the binaries are created correctly. I need to use "./bjam" because the project supplies its own version of bjam to reassure compatibility with its code.
When I use the same command inside the PKGBUILD, compilation starts fine and in the end I get an error in the build() function, without further explanations.
Since I'm not at all familiar with bjam, can anyone point me to some sample PKGBUILDs or give me some tips how to create the PKGBUILD?
TIA
EDIT: It seems no special procedure is needed. The problem occurs due to a failure in the bjam build which forces makepkg to abort.
Last edited by panosk (2012-09-10 19:35:29)

The pkgtools package will do this for you.
See https://wiki.archlinux.org/index.php/Pkgtools for instructions on how to set it up.
Last edited by szim90 (2011-08-03 14:25:58)

How to build a table with predifined? Like Huffman decoding, there are 34 predefined tables?

I am trying to use Labview for mp3 huffman decoding. there are 34 predefined tables for lookup purpose. I tried build array control, but it is so hard to assign value with size of 16. What is the better way to create predefined array? And how to do lookup table with Labview?

IMHO, the best way to have something "predefined" is to read this data from a "setup/configuration" file (if you don't want to use "default settings" LV feature). The choice of the format for all the data that you want to store in some kind of configuration file is up to you.
Also, constructing a "lookup table" in LV doesn't seems different as for any other programming language.

How to call a package with OO4O?

I have designed a package which execute a procedure.
How can I call it with OO4O?
Please give me a sample code.

Hi,
I persume that you are facing this problem when u try to code in VB. If that is the case here comes the code.........
OraDatabase.Parameters.Add "A_NBR_NEWSID", A_NBR_NEWSID, ORAPARM_INPUT, 2
OraDatabase.Parameters.Add "A_NBR_TOPICID", A_NBR_TOPICID, ORAPARM_INPUT, 2
OraDatabase.Parameters.Add "A_NBR_USERID", A_NBR_USERID, ORAPARM_INPUT, 2
OraDatabase.Parameters.Add "result", 0, ORAPARM_OUTPUT
OraDatabase.Parameters("result").serverType = 2
OraDatabase.ExecuteSQL ("declare result Number; Begin :result := PKG_CONTENT_MANAGEMENT.FUN_GET_NEWS_PERM_BY_USERID(:A_NBR_NEWSID, :A_NBR_TOPICID, :A_NBR_USERID); end;")
OraDatabase.Parameters.Remove "A_NBR_NEWSID"
OraDatabase.Parameters.Remove "A_NBR_TOPICID"
OraDatabase.Parameters.Remove "A_NBR_USERID"
FUN_GET_NEWS_PERM_BY_USERID = OraDatabase.Parameters("result").Value
OraDatabase.Parameters.Remove "result"
Hope this clear your doubt..
Raj

For a READ TABLE how to build a dynamic WITH KEY condition?

Hi All,
I have a Z table with 6 fields. The first field is the Plant and is the key field. This field can be matched with the field from selection screen. Now I have 4 character fields which can contain various values. Now I have another field at the end of the table and this field is the one which I will need for further processing.
Now this last field will be selected based on the data for first 5 fields.
This Read is performed in a loop and the data for all the 4 character fields may not be present.
Now my problem is how to build a Read statement for this table where I need to get the value of the Last field based on the values of first 5 fields?

Hi,
    Use
IF    you have internal table With header line then use
      REad Tablename with key field1 = value1   field2 = value2      field3 = value3        field4 = value4    field5 = value5.
If sy-subrc = 0.
endif.
if you have internal table WithOut header line then use
     REad Tablename into workArea with key field1 = value1   field2 = value2      field3 = value3        field4 = value4    field5 = value5.
If sy-subrc = 0.
endif.
regards,
Amit

How to build distribution package with Agilent VISA as primary

Similar Messages

Maybe you are looking for