How to configure a Sun Type 7 Keyboard (Solaris 10 11/06)
Hi.
I bought a Sun Type 7 (UNIX) keyboard. I plugged it in and configured Xorg's kbd driver to use this kind of keyboard. The problem is that some keys, such as the 3 volume keys, the sleep key, the composite key, doesn't appear to work. In the official documentation there's no other installation hint but "to plug it in".
Has anyone any experience configuring this keyboard?
Thanks again,
Enrico.
hello.
Just do this:
eeprom kbd-type=Frenchafter reboot.Hello,
"eeprom" is fine on a SPARC box, but how do I do this on a x86 box ?
TIA.
Similar Messages
-
How to configure a internal modem in solaris X86
Hi,
We were testing a solaris installation in one of my friend's sysytem and i would like to know how to configure an internal modem in solaris to dial out to ISP. If some one can help us in setting this up it will be really helpful.
Waiting for your response
Thanks in advance
CSHi Sharmac,
Try this URL:
http://www.geocities.com/~gregl/htm/Int_Modem_Setup.htm
Revert back.
Thanks & Regards,
Senthilkumar
SUN - DTS -
How to configure to access internet on Solaris 10 SPARC
Dear All,
how to configure to access internet on Solaris 10 SPARC.
Thanks and regards,
HengWhat you need is just an IP address on your network interface and configure dns in /etc/nsswitch.conf and /etc/resolv.conf.
More details here : http://docs.oracle.com/cd/E23823_01/html/816-4554/index.html -
How to configure add document types in pr
how to configure add document types in pr
Hi
Just check out the following document for Configuring PO doc tpe , PR config is similar to that just need to do selection form PR
[Po doc configuration|http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/703cdc83-d604-2c10-c79c-c30eab6c56a8?QuickLink=index&overridelayout=true ] -
PR05: How to configure the expense types depending on the type of expense?
Hi,
We are in the process of upgrade from 4.6C to ECC 6.0. The problem is that when we are creating the expense request, after selecting the type of expense (travel expense or non travel expense) we are getting the same expense types for both the travel and non travel expenses.
Now my question is that, is there any in error in configuring the expense types in transaction FITVFELD.
How to configure the expense types depending on the type of expense (travel and non travel)?
Your answer will be highly appreciated.
Thanks in advance.
RamanaHi
I checked with one of the SUBJECT MATTER EXPERT on T&E and it is not possible to have the expense types based on the schema.
Thanks
Ashok
Award points if this is useful -
How do I determine what type of Solaris installation I have ?
I'm runnig "SunOS PSP 5.8 Generic_108528-13 sun4u sparc SUNW,Sun-Fire-480R" but I would like to determine the type of Solaris installation I have....do I have a a "development" installation ? Do I have all the SUNW developer packages ? Also what are the "types of installations" that are possible ?
I'm thinkig about download the mysql binary (from Sunfreeware.com) and I went to the dpendencies site (http://wwws.sun.com/software/solaris/freeware/s8u7dependencies.html) to check what dependencies exist and I saw the following line (among other non "related" info.):
mysql-3.23.43 gcmn-1.0 ncurses-5.2
What exactly does this mean ?Hi
You can check the type of solaris install from the below file
/var/sadm/system/admin/CLUSTER
Regards -
How to configure this material type We will treat it as consumable goods?
Dear Experts,
How to create new material type which we will treat as consumable goods?
Also, for all purchase, we want to have the GR Non-valuated checked so that the actual cost will not have effect after goods receipt but will be effective when the invoice has been entered. No inventory will be used. We will treat it as other consumable goods.
For GR Non-valuated, it means the actual cost will not happen in goods receipt only.
we will create po and gr and invoice and payment. can you tell me what we have to pay attention to ?
Best Regards,
Merryyou can use material type UNBW, because its having non valuted ticket and quantity updation also not there, and you can do PO, GR, Invoice and payment as a normal process, but the only difference is when you do GR the value of that GR is immediately charge out to an account or cost center including quantity. but you will do the MIRO to clear GR/IR account.
regards,
qsm sap -
How to configure script output type in vt01 (where) ?
I have output type zmi0...
I have configured in /nnace..
In /nvt01, where to configure my outpout type ..printer and all
Please help me.Ur query is not clear.
After creating output type u have to assign it in the NACE tcode.
After that for a particular vt02 go and enter the sipment no and that u have option for enetring the output type.
Regards -
Print HTML using JPS API.. How to configure printer MIME-TYPE as text/html
Hi All,
I have to print the HTML pages.. for this i have used JPS API , but i found that my printer doesnt supoort Mime-type(Flavour) text/html.
Can someone help me in this ...
i) Can i configure my printer for this Mime-type , if yes then HOW?
ii) Is there any work around ?
Thank you all in advance :)I reposted this question in the Database forum. Admin can feel free to delete this thread.
The answer is to add this at the top: htp.addDefaultHTMLHdr(false);
Thanks,
T.
Edited by: 855677 on May 3, 2011 9:35 AM -
How to configure a Graphic Terminal at Solaris 9
Hello everyone!
I�m having difficulties while finding a compatible Solaris 9 driver for my video card.
I have installed Solaris 9 in my PC, but I can only work with the text terminal, what is not interesting because I need to export a remote window from a server to my local machine.
I�m using Diamond Multimedia Viper II Z200 as my video controler.
Any help is useful.
Thank you all for the attention.From the command console run:
/usr/sbin/kdmconfig
Configure the hardware device by selecting the closest match. Please pay attention to the other configurable items as well. Make certain you get the mouse, monitor size and display resolution correct in the process or you may end up locked onto a blank screen.
I don't recall seeing that type of (Diamond?) Video Card in the device options of kdmconfig but I have never looked for it. Perhaps you might want to slip a common ATI or Nvidia card into your AGP slot if you can't find a device driver for yours.
best...
Mike -
How to configure st microcontroller, type STEVAL-MK1062V
I am not able to get with arm porting guide . I dont have this RTX_Conf*.c file too.
Thank you '
RajI am not able to get with arm porting guide . I dont have this RTX_Conf*.c file too.
Thank you '
Raj -
How to configure ASM of 11gR2 RAC on Solaris 10
Hi all,
I have the first time to install the RAC on Solaris 10. I have stuck on the ASM disk group step in the Grid Infrastructure.
Our Configuration
2 Sun Server in Solaris 10 with same configure (which we are not using shared drive)
250GB Local Hard Disk
1100 GB Raw Disk (which at SAN)
3GB x 3 Raw Disk (which at SAN) for voting disk
When I install Grid Infrastructure, I select first option: Install and Confgure Grid in Cluster (I can't remember the exact name) and also select the Typical Installation. The previous steps are successful before the ASM Disk Group. At ASM Disk Group, no disk are display for selection.
So, how to fix the missing disk in this ASM Disk Group creation?
Please help!
Sunny Yip952832 wrote:
Hi all,
I have the first time to install the RAC on Solaris 10. I have stuck on the ASM disk group step in the Grid Infrastructure.
Our Configuration
2 Sun Server in Solaris 10 with same configure (which we are not using shared drive)
250GB Local Hard Disk
1100 GB Raw Disk (which at SAN)
3GB x 3 Raw Disk (which at SAN) for voting disk separate voting disks in 11gR2 are not necessary.
I would break the 1100G into 11@100G devices and use EXTERNAL redundancy (RAID on the SAN side). You will get much better performance. (Configured/managed a 250TB 3node cluster on Sun 6900s however my LUNs were 1.5TB in size)
>
When I install Grid Infrastructure, I select first option: Install and Confgure Grid in Cluster (I can't remember the exact name) and also select the Typical Installation. The previous steps are successful before the ASM Disk Group. At ASM Disk Group, no disk are display for selection.
So, how to fix the missing disk in this ASM Disk Group creation?
Please help!
Sunny YipAgain using a single 1.1TB device will not get you better performance and should you need to add additional devices, they too will need to be 1.1TB. Sometimes smaller is better.
Make sure you use a partition that starts at cylinder 1 or 2
Make sure you set the correct permissions (660) and ownership (gridowner:oinstall) on those devices and make sure the oracle user is a member of that group. -
How to configure network printer on solaris 10 intel based
how to configure the network printer in solaris 10
like hp laserjet printer/printers,Very very easy.
Go to the print manager . (printmgr I believe or in the launch menu under preferences)
select add a network printer
Fill out the info. I find that the hpijs printer driver works better then the suggested foomatic on my hp 4000s. I could not print pdfs otherwise.
Other things to know is the protocol should be BSD (at least it works for me). And add the port to the destination so 192.168.0.1:9600 for example (for hp).
thats about it. To have it show up correctly in JDS you should probably add it to the printer list under the launch->preferences->printer preferences. -
How to Customize a document type to use on CV01N transaction in SAP
I am trying to create a attach document in CV01N but I want to set up a new document type and don't want to use existing ones, so can some one help me in how to configure new document type and also please tell everything in step by step in order to xcomplete this process successfully.
HI,
1. Define Number Ranges for Document Numbers
T code OD00
SPRO / IMG -> Cross - Application Component -> Document Management System -> Control Data -> Define Number Ranges for Document Numbers
2. Define Document Type
T code DC10
SPRO / IMG -> Cross - Application Component -> Document Management System -> Control Data -> Define Document Types.
In this step, you create Document Type for categorize documents according to the organizational procedures.
Supppose u define ZAD
Document Type The document type is used to categorize documents according to the organizational procedures. E.g. in company, there exists many departments for which separate document types have been created. For example, ZAD,ZCB,ZCD etc Document type is a three digit alphanumeric field.
Document Type Description Description appears in the screen heading when document info record is being processed.
Use Kpro Indicator controls that the original files are stored in defined content repository via Knowledge Provider.
Assignment of Revision Level This indicator shows that a revision level is automatically assigned to a document the first time the document is released with reference to a change number.
CM Relevance u2018 u2018 u2013 Not Relevant for Configuration Management
u20181u2019 u2013 Relevant for Configuration Management
Determines whether Configuration Management controls the object.
Number Exit MCDOKZNR Program that controls number assignment and version numbering for documents.
Regards,
Pardeep Malik -
Reg: How to Configure internet for solaris 10 in x86 32 bit
Hi,
I am new to Sun Solaris can any one help me detailed step of how to configure internet for standalone pc. Thanks in Advance
Thanx
MAOK, the classical way:
Open a terminal.
Type
ifconfig -a
ifconfig -a plumb
ifconfig -a
Note the differences, it will plumb ALL available interfaces this way. So, now you can see, which device is your network card.
Then perform a
ifconfig <interface> unplumb
for all the newly interfaces (aka those, that were new in the last ifconfig -a output).
Then, the simple way:
cd /etc
vi hostname.<interface-driver-name>0 (example: hostname.rge0, the driver would be rge, the instance is 0, and rge0 would have been displayed as an available interface in the last ifconfig command). Add the name of the host into this file.
Then
vi /etc/inet/hosts
and add the pair of IP-address and hostname.
If needed:
vi /etc/inet/netmasks
if you have a sub-divided network, and you need a differenbt subnet mask...
Then:
vi /etc/defaultrouter
and add the name or ip-adress of the gateway... (name only, if you have that name also in the /etc/inet/hosts file!)
Also:
vi /etc/nodename
and add the name of your host into that file, so that the system knows, who it is... ;-)
And: For the DNS you can then add the infos into:
/etc/resolv.conf
For example:
nameserver 192.168.2.1
or some such...
Then, as the last but one step:
ls /etc/nsswitch.*
and:
cd /etc
cp nsswitch.<what you need> nsswitch.conf (should be .files here!)
And the reboot... ;-)
HTH!
Matthias
P.S.: There might be some GUI, but I'm an old-timer, so I prefer the command-line version of things...
Maybe you are looking for
-
How can I delete an alias of a file that has been deleted already?
A couple of days ago I took a screen shot of my flight's itinerary for this summer vacations. Without noticing I created an alias of the file...I deleted the screen shot and now I just have the alias and i can not delete it nor dragg it anywhere ....
-
Uploading data from a particular column of a particular sheet from an excel file into internal table
Hi, I have to upload data in the first coulmn of 7th sheet of an excel file. Can anyone please help me on this. This link works perfectly fine for excel files without Macros. Read multiple sheets of an Excel file into SAP through ABAP - Code Gallery
-
Question regarding a method of stocking data
I know this thread already is in the "New to Java Technology" Forum, although I said the topic was closed there so I could open it back here.. I realized it would be more fitting here and it would probably get more replies... I am working with a frie
-
The file will appear in the location that I set for downloads, but this is not convenient to constantly return to the computers main window and extract the file.
-
Will a US factory unlocked iphone 4s work in india ?
hi , i just wanted to knw will a iphone 4s purchased frm US retail store factory unlocked iphone work without any problem in india ?hv i to purchase at higher price in india only ?