How to Configure Internet on Solaris 10
Hi Guys,
I recently installed Solaris 10 on Vmware Workstation 7.0.1. I'm trying to get Internet to work in the solaris virtual machine by sharing it from the host machine but have not been successful.The Solaris Virtual Machine NIC is using NAT. Please help.
Thanks
kisad
Thank You for your reply. This is what i have configured.
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.0.0.51 netmask ffffff00 broadcast 10.0.0.255
ether 0:c:29:42:c3:b4
netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd
default 0.0.0.0 10.0.0.1 1500* 0 1 UG 0 0
10.0.0.0 255.255.255.0 10.0.0.51 e1000g0 1500* 0 1 U 0 0
224.0.0.0 240.0.0.0 10.0.0.51 e1000g0 1500* 0 1 U 0 0
127.0.0.1 255.255.255.255 127.0.0.1 lo0 8232* 0 9 UH 278 0
Similar Messages
-
Reg: How to Configure internet for solaris 10 in x86 32 bit
Hi,
I am new to Sun Solaris can any one help me detailed step of how to configure internet for standalone pc. Thanks in Advance
Thanx
MAOK, the classical way:
Open a terminal.
Type
ifconfig -a
ifconfig -a plumb
ifconfig -a
Note the differences, it will plumb ALL available interfaces this way. So, now you can see, which device is your network card.
Then perform a
ifconfig <interface> unplumb
for all the newly interfaces (aka those, that were new in the last ifconfig -a output).
Then, the simple way:
cd /etc
vi hostname.<interface-driver-name>0 (example: hostname.rge0, the driver would be rge, the instance is 0, and rge0 would have been displayed as an available interface in the last ifconfig command). Add the name of the host into this file.
Then
vi /etc/inet/hosts
and add the pair of IP-address and hostname.
If needed:
vi /etc/inet/netmasks
if you have a sub-divided network, and you need a differenbt subnet mask...
Then:
vi /etc/defaultrouter
and add the name or ip-adress of the gateway... (name only, if you have that name also in the /etc/inet/hosts file!)
Also:
vi /etc/nodename
and add the name of your host into that file, so that the system knows, who it is... ;-)
And: For the DNS you can then add the infos into:
/etc/resolv.conf
For example:
nameserver 192.168.2.1
or some such...
Then, as the last but one step:
ls /etc/nsswitch.*
and:
cd /etc
cp nsswitch.<what you need> nsswitch.conf (should be .files here!)
And the reboot... ;-)
HTH!
Matthias
P.S.: There might be some GUI, but I'm an old-timer, so I prefer the command-line version of things... -
How to Configure internet channel to a relay SMTP server
Hi men,
My problem is How to Configure internet channel(or outbound mail) sending to a relay SMTP server. I want to test my spam software.
I have search and read Sun Messaging Administration document but haven't fought the guide.
./imsimta version
Sun Java(tm) System Messaging Server 7.0-0.04 32bit (built Jun 20 2008)
Thank and Regards,
Duc Tien.tien86 wrote:
My problem is How to Configure internet channel(or outbound mail) sending to a relay SMTP server. I want to test my spam software. You can use the daemon channel keyword with the tcp_local channel e.g.
! tcp_local
tcp_local smtp nomx multiple remotehost inner switchchannel identnonenumeric \
pool SMTP_POOL maytlsserver maysaslserver saslswitchchannel tcp_auth loopcheck \
daemon relay.yourdomain.com
tcp-daemonIf the relay SMTP server only has an A record then use "nomx" instead of "mx".
http://msg.wikidoc.info/index.php/Mx%2C_nomx%2C_nodns%2C_defaultmx%2C_randommx%2C_nonrandommx%2C_nameservers%2C_defaultnameservers_Channel_Options
The "multiple" keyword instead of "single_sys" helps performance by increasing the number of emails per connection when sending to a relay system.
http://msg.wikidoc.info/index.php/Multiple%2C_addrsperfile%2C_single%2C_single_sys_Channel_Options
Regards,
Shane. -
How to configure Internet settings on Iphone 4, os 4.3
Hey I got replacement handset from apple store...But the problem is I lost my internet and mms settings ....How to configure internet and mms in os 4.3??Hey I got replacement handset from apple store...But the problem is I lost my internet and mms settings ....How to configure internet and mms in os 4.3??
There are none unless it's built in to the Skype app.
-
How to configure PPPoE in solaris 10
Hi
As I have to configure Internet in one Intel based Solaris box [Solaris 10] can you tell me the steps how to configure it as I have Brodband connection of Iqara.hi,
did you configure your interface for pppoe? the first step is configuring your interface for ppoe and then you can define a pppoe access server.
please look at http://docs.sun.com/app/docs/doc/816-4555/6maoquija?a=view for details.
yavuz -
How to configure postfix in Solaris 10?
Hi guys,
I need doc or link on how to configure postfix(mail send from server has to be forwarded to mail host which takes care of delivery) in Solaris 10 as i am facing issues with sendmail. I tried googling but couldnt find out any useful stuff.
Thanks in adavance...http://www.postfix.org/documentation.html
-
How to configure internet proxy for portlet builder
Hi All,
We have downloaded the portlet builder from developer.bea.com. But while trying
to access xmethods for adding web service, it can't access as the internet connection
is thru proxy.
Can anybody pls tell me how to configure the internet proxy with this portlet
builder ?
TIA,
SudarsonHi, I got the same problem...I try to configure a web service with Portal Builder
7.0 in Bea E-Business Control Center... But I can not proceed cause there is no
hint for a proxy... Have you found a solution?
"sudarson" <[email protected]> wrote:
>
Hi All,
We have downloaded the portlet builder from developer.bea.com. But while
trying
to access xmethods for adding web service, it can't access as the internet
connection
is thru proxy.
Can anybody pls tell me how to configure the internet proxy with this
portlet
builder ?
TIA,
Sudarson -
How to configure default gateway Solaris 9
How to configure default gateway using /etc/gateways file (NO /etc/defaultrouter).
The line "net default gateway ip_router metric 1 passive" produce the following error message:
in.routed: bad net "default" in /etc/gateways entry "net default gateway ip_router metric 1 passive"--cannot be default.
With Solaris 8 is ok.
Can you help me.you've probably worked this out by now, but this may help others;
net 0.0.0.0 gateway x.x.x.x metric 1 passive
* x.x.x.x = your gateway IP -
How to configure CUPS in Solaris 10 X86 and SPARC
Dears,
I need help in configuring CUPS for Solaris 10 X86 as well as on SPARC.
What i did?
Downloaded the CUPS 1.5.0
read the readme.txt
read the INSTALL.txt
Pre-req installation requires :-
CFLAGS= -i /some/directory \
CPPFLAGS = -i /some/directory \
CXXFLAGS = -I /some/directory \
DSOFLAGS = -L /some/directgry \
LDFLAGS = -L /some/directory \
./configure --
It errors out with
checking for gawk ... no
checking for mawk... no
checking for nawk ...nawk
chekcing for gcc ... no
checking for cc ... no
checking for cl.exe no
Configure error: no acceptable C compiler found in $PATH
see 'config.log' for more details
I installed all the missing dependencies from www.sunfreeware.com and I have the same problem.
I also tried to install the software packages from the operating system dvd... like for
ls -lrt gcc
gcc "SUNWgcc", "SUNWgccS", "SUNWgccruntime"
ls -lrt cc
cc "SUNWgccruntime", "SUNWlccom", "SUNWcctpx", "SUNWccisgn" , "SUNWccinv", "SUNWccfwctrl", " SUNWccfw", "SUNWccccrr", "SUNWccccr", "SUNWccccfg", "SUNWislcc",
"SUNWaccu", "SUNWaccr", "IPLTccons", " SUWgccs", "SUNWgcc", "SUNWmccom", "SUNWmcc", "SUNWusbccids", "SUNWusbccid"
ls -lrt gawk
no results
ls -lrt mawk
no results
ls -lrt cl.exe
no results
Is there any way should i follow apart from the above?
Rgds,
MkyCheck pkginfo -l for each package.
export the PATH variable where the packages are installed, like /usr/local/bin and etc. -
How to configure internet domain name for P6 website using weblogic
After installing and configuring weblogic for P6 you get the following address https://servername:7002/console/login/LoginForm.jsp to access P6 website. Anyone know how to configure a purchase domain such as www.mydomain.com have it redirect to https://servername:7002/console/login/LoginForm.jsp Is this configured in weblogic server? If not, what is needed to redirect the purchased domain?
HI
You could have that domain resolving to/by some DNS servers and set up a load balancer / proxy to redirect every incoming request to that domain / site to your weblogic console.
however , what is it you are trying to do? It is very unsual of redirecting/ using Domain names to redirect to wls consoles.
could you explain your use case in detail please
Sri -
Configuring Internet on solaris 10!!
Hello everyone,
I am new to solaris 10, i use broadband internet that requires username and password. Please tell me how can i configure it using java dsktop. Please tell from the scratch.
waiting for reply
AmitojSorry for my English, please.
I have a DSL connection that uses username and password, I use network card and router modem.
I can connect using ppp. It's easy to configure. First of all test your network configuration, or type sys-unconfig and clear all.
When the computer reboot, answer the questions, network? yes. router NO, DHCP NO, services DNS, other questions will be video driver, keyboard, etc.
You have in :http://www.phildev.net/solaris/spppoe.htlm an excellent guide for configure ppp.
REMEMBER: First reconfigure your system, I had a several days lost configuring ppp. -
How to configure snmp on solaris 10
hi, i am working on solaris management console(smc) .i want to configure snmp for this to send traps regarding my system performance and cpu usage ..can any body know ho to do this
I could use some help with this as well ... so far I have been unable to find a clear and concise document that can walk me through configurin gSNMP. Clean Solaris 10 installation, snmpdx is running - now how do I configure it? Better yet, how do I disable snmpdx and run net-snmp?
Please, someone help or at least paste a link to an article somewhere... -
How to configure snmp on solaris 10 for sending traps to any EMconsole
i am working on solaris management console(smc) .i want to configure snmp for this (smc)to send traps regarding system performance and cpu usage ..can any body know ho to do this .i am new to solaris ..learned some basic administration of it ..
I could use some help with this as well ... so far I have been unable to find a clear and concise document that can walk me through configurin gSNMP. Clean Solaris 10 installation, snmpdx is running - now how do I configure it? Better yet, how do I disable snmpdx and run net-snmp?
Please, someone help or at least paste a link to an article somewhere... -
How to configure Internet connection?
I've just installed Solaris 10 x86.
It did not detect and configure the ethernet card, which is connected to a DSL router. How do I set this LAN?You need to identify the ethernet card. The name of the device depends on the type of card. Once you have the name of the device you can use the ifconfig (see man pages) to configure it. Usually,
ifconfig devnam plumb
ifconfig devnam dhcp
will get the interface up and running from your router, then you will need to add the domain name servers to
/etc/resolv.conf
and
copy /etc/nsswitch.dns to /etc/nsswitch.conf
to get the naming services working.
It may be neccessary to add a default route to your router using something like
route add default 192.168.0.1 -
How to configure Internet/
Hi i have installed Solaris 10 u5 now and I also have the LAN connection. So my query is How should I configre the LAN? like IP Address, DNS..
my best guess would be
ifconfig <interface> dhcp
if you don't know what that interface is.. find it with ifconfig -a plumb
then configure the one that comes up.. if it is more than one.. use snoop to find out which one is connected to you switch...
vi your /etc/resolv.conf and add the right entries...
then
route add default <ip of your main router>
Maybe you are looking for
-
I am trying to do something that requires Flash Player, but even though it shows in my control panel, and it is the latest version, I keep seeing a notice that it is disabled, and it does not appear in the list of plugins, so I don't know how to enab
-
Bridging a WPA2 Enterprise Radius Server (Lion Server) to Apple TV
Hello, I was wondering if anyone can help me out with this setup that I have with Lion Server. Recently I set up my Airport Extreme to use Radius and bind it to my Lion Server for Authentication. Radius works with most of my devices, except for my AT
-
How to create a clickable video link in Contribute
I am new to Contribute and am trying to figure out how to do the following. I have a video on my website and want to insert an image with a play button which will link to the video on my site. The video is on an html page with swf embedded in it (c
-
ALE/ IDOC CONFIGURATION OBJECT
IT'S URGENT I NEED AN OBJECT IN ALE/IDOC CONFIGURATION SETTINGS
-
Some contact picture are missing from verizon messaging
brand new s5 set up messaging for my husband. all contact pictures show up in verizon messaging but mine. there is a picture for me under contacts. no idea why this is happening. husband uses google for contacts and linked to facebook we use syne